Craftsman 580.752290 Owner's manual

Brand: Craftsman

Model: 580.752290

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

580752290

Operator'siVlanual

3100 PSi MAX

2.8 GPMMAX

Model No. 580.752290

PRESSUREWASHER ,_

CUSTOMERHELPLINE

HOURS: Non. - Fri. 8 a.m. to 5 p.m. (CT)

WAemG

Before usingthis product, readthis

manualand follow all SafetyRules

and Operating Instructions.

1_-illADVERTEHCIA

Antes de utilizar el producto, lea este

manualy siga todas las Regiasde

Seguridade Instrucciones de Uso.

Sears, Roebuckand Co., RoffmanEstates,IL 60179 U.S.A.

Visit ourCraftsman website:www.craftsman.cnm

Part No. 206170GS Draft A (01/18/2008)

,, Safety

,,Assembly

,, Operation

=Maintenance

,, Parts

• Espafiol,p. 32

WARRANTY.......................................... 2

SAFETYRULES...................................... 2-5

FEATURESANDCONTROLS.............................. 6

ASSEMBLY........................................ 7-10

OPERATION....................................... 11-16

SPECIFICATIONS..................................... 17

MAINTENANCE.................................... 18-22

STORAGE........................................... 23

TROUBLESHOOTING.................................. 24

REPLACEMENTPARTS.............................. 25-29

EMISSIONCONTROLWARRANTY..................... 30-31

ESPANOL......................................... 32-55

HOWTO ORDERPARTS........................ BACKPAGE

ONE-YEARFULLWARRAHTYONCRAFTSMAHPRESSUREWASHER

If this pressurewasher fails dueto a defectin material or workmanship within one year from the dateof purchase,return it to

any Searsstore, other Craftsman outlet, or SearsParts & RepairCenterin the UnitedStates or Canadafor free repair (or

replacementif repair proves impossible).

All warranty coverageapplies for only 90 days from dateof purchaseif this pressure washer is ever usedfor commercial or

rentalpurposes.

This warranty gives you specific legal rights, and you mayalso haveother rights which vary from stateto state.

Sears, Roebuck and Co., Hoffman Estates, IL 60178

Sears Canada Inc., Toronto, Ontario, Canada M5B 288

,_ Thisisthe safetyalert symbol.It isusedto alert youtopotentialpersonalinjuryhazards.Obeyall safetymessages

thatfollow thissymboltoavoid possibleinjuryor death.

_Read this manualcarefully and becomefamiliar

with yourpressurewasher. Knowits applications,

its limitations, and any hazardsinvolved.

Thesafety alert symbol (_&.) is usedwith a signal word

(DANGER,CAUTION,WARNING),a pictorial and/or a safety

messageto alert you to hazards.BANGERindicatesa hazard

which, if not avoided, willresult in deathor serious injury.

WARNINGindicates a hazardwhich, if not avoided, could

result in deathor serious injury. CAUTIONindicatesa hazard

which, if not avoided, might result in minor or moderate

injury. NOTICEindicatesa situation that could result in

equipment damage. Follow safety messagesto avoid or

reducethe risk of injury or death.

Hazard Symbolsand Meaninos

ToxicFumes ElectricalShock

2 5-

SlipperySurface Fall

Fire

Explosion

FluidInjection

Operator'sManual

HotSurface

MovingParts FlyingObjects

Kickback

WARHING

Theengineexhaustfromthisproductcontains

chemicalsknowntothe State of California tocause

cancer,birthdefects,or otherreproductiveharm.

WARHIHG

Runningengine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathingcarbon monoxide can cause headache,

_ atigue, dizziness,vomiting, confusion, seizures,

nausea,fainting or death.

Some chemicals or detergents may be harmful if

inhaled or ingested, causing severe nausea,

fainting, or poisoning.

* OperatepressurewasherONLYoutdoors.

Keepexhaustgasfromenteringaconfinedareathrough

windows,doors,ventilationintakes,or otheropenings.

DONOTstartor runengineindoorsor in anenclosedarea,

evenif windowsanddoorsareopen.

Usea respiratoror maskwheneverthereisa chancethat

vaporsmaybeinhaled.

* Readall instructionswith masksoyouarecertainthemaskwill

providethenecessaryprotectionagainstinhalingharmful

vapors.

WARHIHG

_Fuel and its are extremely flammable and

vapors

explosive.

Fireor explosion cancause severe burns or

death.

WHENADDINGORDRAININGFUEL

* TurnpressurewasherOFFandletit coolatleast2 minutes

beforeremovingfuelcap.Loosencapslowlyto relievepressure

in tank.

Fillor drainfueltankoutdoors.

DONOToverfilltank.Allowspaceforfuelexpansion.

Iffuelspills,waituntilit evaporatesbeforestartingengine.

Keepfuelawayfromsparks,openflames,pilotlights,heat,and

otherignitionsources.

DONOTlighta cigaretteorsmoke.

WHENSTARTINGEQUIPMENT

* Ensuresparkplug,muffler,fuelcap,andair cleanerarein

place.

* DONOTcrankenginewith sparkplugremoved.

WHENOPERATINGEQUIPMENT

* DONOTtip engineor equipmentat anglewhichcausesfuelto

spill.

* DONOTsprayflammableliquids.

WHENTRANSPORTINGORREPAIRINGEQUIPMENT

* Transport/repairwithfueltank EMPTYor withfuelshutoffvalve

OFF.

* Disconnectsparkplugwire.

WHENSTORINGFUELOREQUIPMENTWITHFUELINTANK

* Storeawayfromfurnaces,stoves,waterheaters,clothes

dryers,or otherappliancesthathavepilotlightor otherignition

sourcebecausetheycanignitefuelvapors.

WARHIHG

'__¢ Risk of electrocution.

Contactwith power source can causeelectric

shock or burn.

NEVERspraynearpowersource.

WARHIHG

Startercord kickback(rapid retraction) can result

in bodily injury. Kickbackwill pull handand arm

_,_< toward enginefaster than youcan let go.

Brokenbones, fractures, bruises, or sprains

could result.

* NEVERpullstartercordwithoutfirst relievingspraygun

pressure.

* Whenstartingengine,pullcordslowlyuntilresistanceisfelt

andthenpull rapidlyto avoidkickback.

Aftereachstartingattempt,whereenginefailsto run,always

pointspraygunin safedirection,pressredbuttonandsqueeze

sprayguntriggerto releasehighpressure.

Firmlygraspspraygunwith bothhandswhenusinghigh

pressuresprayto avoidinjurywhenspraygunkicksback.

WARHIHG

Useof pressure washer cancreate puddles and

slippery surfaces.

Kickbackfrom spray gun cancause you to fall.

* Operatepressure washer from a stable surface.

The cleaningarea should haveadequateslopes and drainageto

reducethe possibility of afall dueto slippery surfaces.

Be extremelycareful if you must usethe pressure washer from

a ladder, scaffolding, or any other similar location.

Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARHIHG

_ ontact with muffler area can result in serious

burns.

_ Exhaustheat/gases can ignite combustibles,

structures or damagefuel tank causing a fire.

, DONOTtouchhotpartsandAVOIDhotexhaustgases.

, Allowequipmentto coolbeforetouching.

* Keepatleast5feet (152cm) ofclearanceonall sidesof

pressurewasherincludingoverhead.

, Codeof FederalRegulation(CFR)Title36 Parks,Forests,and

PublicPropertyrequireequipmentpoweredbyaninternal

combustionengineto haveasparkarrester,maintainedin

effectiveworkingorder,complyingto USDAForestservice

standard5100-1Corlaterrevision.IntheStateofCaliforniaa

sparkarresteris requiredundersection4442oftheCalifornia

Publicresourcescode.Otherstatesmayhavesimilarlaws.

WARHIHG

The high pressure stream of water that this

equipment produces can cut through skin and its

_ nderlying tissues, leading to serious injury and

)ossible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• DONOTallow CHILDRENto operate pressure washer.

, NEVERrepair highpressure hose. Replaceit.

• NEVERrepair leakingconnections with sealantof any kind.

Replaceo-ring or seal.

, NEVERconnect high pressure hoseto spray tip extension.

• Keephigh pressure hoseconnectedto pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button

and squeezespray gun trigger, to release high pressure, every

time you stop engine.

• NEVERaim spray gun at people, animals, or plants.

, DONOTsecure spray gun in open position.

• DO NOTleavespray gun unattendedwhile machine is running.

, NEVERusea spray gun which does not have atrigger lock or

trigger guard in place and in working order.

• Always be certain spray gun, spray tips and accessories are

correctly attached.

WARHIHG

_ Unintentional sparking can result in fire or

_¢ electric shock.

WHENADJUSTINGORMAKING REPAIRSTOYOUR PRESSURE

WASHER

Disconnectthe sparkplug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHENTESTINGFORENGINESPARK

* Useapproved sparkplug tester.

DONOTcheck for sparkwith spark plug removed.

WARHJHG

_ IStarter and other rotating parts can entangle

hands, hair, clothing, or accessories.

* NEVERoperatepressure washer without protective housing or

covers.

. DO NOTwear loose clothing, jewelry or anything that may be

caught in the starter or other rotating parts.

. Tie up long hair and remove jewelry.

WARNING

Risk of eye injury.

Spray can splash back or propel objects.

Alwayswear safetygoggles when using this equipment or in

vicinity of where equipment is in use.

Beforestarting the pressure washer, be sureyou are wearing

adequatesafetygoggles.

NEVERsubstitute safetyglasses for safety goggles.

NOTICE

High pressure spray may damage fragile items including

lass.

DONOTpoint spraygunatglasswhenusingred(0°) spraytip.

NEVERaim spray gun at plants.

NOTICE

Improper treatment of pressure washer can damage it and

shorten its life.

Ifyou have questions about intended use, ask dealer or contact

Sears.

NEVERoperate units with broken or missing parts, or without

protective housing or covers.

DONOT by-pass any safety device on this machine.

DONOTtamper with governed speed.

DONOToperate pressure washer above rated pressure.

DONOT modify pressure washer in any way.

Before starting pressure washer in cold weather, check all parts

of the equipment to besure ice has not formed there.

NEVERmove machine by pulling on hoses. Use handle

provided on unit.

Checkfuel system for leaksor signs of deterioration, such as

chafed or spongy hose,loose or missing clamps, or damaged

tank or cap. Correct all defects beforeoperating pressure

washer.

This equipment is designedto be usedwith Searsauthorized

parts ONLY.If equipment is used with parts that DO NOT

comply with minimum specifications, userassumes all risks

and liabilities.

KNOWYOURPRESSUREWASHER

_Head the Operator'sManual andsafety rulesbefore operatingyourpressurewasher.

Comparethe illustrations with your _ressurewasher to familiarizeyourself with the locations of various controls and

adjustments. Savethis manualfor future reference.

A - Spray Gun-- Controls the application of water onto

cleaning surfacewith trigger device.Includestrigger lock.

B - Spray Tips -- Detergent,0°, 15° and 40°: for various

high pressure cleaning applications.

C- Accessory Tray -- Providesconvenient storage for

standard and optional accessories,such as brushes,

turbo wands, etc.

D - High Pressure Hose-- Connect oneend to water pump

and the other end to spray gun.

E - Bottle Brackets -- Cleaningsolution bottles fit in wire

form brackets here.Concentratebottles not included.

F - Spray Tip Extensionwith QuickConnect-- Allows you

to switch betweenfour different spray tips.

G - Choke Lever-- Preparesa cold engine for starting.

H - Air Filter -- Protects engine by filtering dust and debris

out of intake air.

J - Recoil Starter -- Usedfor starting the engine manually.

K- Fuel Valve-- Usedto turn fuel supply on and off to

engine.

L - Throttle Lever-- Setsengine in starting mode for recoil

starter and stops a running engine.

M - FuelTank -- Filltank with regular unleadedfuel. Always

leaveroom for fuel expansion.

N - Warning/OperatingInstructions Tag-- Identifies

hazards and proper procedureto start/stop pressure

washer.

P - Standard DetergentSiphoning Tube/Filter-- Useto

siphon pressure washer safe detergents into the low

pressure stream.

Q - Water Inlet -- Connectionfor garden hose.

R - High Pressure Outlet-- Connectionfor high pressure

hose.

S - Automatic Cool Down System -- Cycleswater through

pump when water reaches125°-155°F. Warm water will

discharge from pump onto ground. This system prevents

internal pump damage.

T - Pump-- Developshigh pressure.

U - Project Pro®PerfectlVIWMSiphon -- Mixes concentrate

with pressure washer spray.

Items Not Shown:

Oil Drain -- Drainengine oil here.

DataTag (near rear of baseplate) -- Provides model and

serial number of pressure washer. Pleasehavethese readily

availableif calling for assistance.

Oil Fill -- Checkand add engine oil here.

Safety Goggles-- Always usethe enclosedsafety goggles

when running your pressure washer.

Your pressure washer requires some assembly and is ready

for useonly after it has been properly servicedwith the

recommendedoil and fuel.

If you haveany problemswith the assemblyof your

pressurewasher, please call the pressurewasher heipline

at 1-800-222-3135.

UNPACKPBESSUREWASHER

1. Removeeverything from carton exceptpressure washer.

2. Opencarton completely bycutting eachcorner from top

to bottom.

7. Attach spray tip extensionto spray gun.

8. Select/attachQuick Connectspray tip to spray tip

extension.

Attach Handle and Accessory Tray

1. Placehandle (A) onto handlesupports (B) connectedto

main unit. Make sure holes (C) in handlealign with holes

3. Removepressure washer from carton.

CARTONCONTENTS

Checkall contents, if any parts are missing or damaged,call

the pressure washer helpline at 1-800-222-3136.

* Main Unit

* Handle

* AccessoryTray

* High PressureHose

* Spray Gun

* Spraytip Extensionwith Quick ConnectFitting

* Bottle BracketWireform (2)

* PerfectMixTMSiphoningUnit/Hose

* StandardSiphoning Hose

* Oil Bottle

* Parts Bag (which includes the following):

* Operator's Manual

* Owner's RegistrationCard

* SafetyGoggles

* Bagcontaining 4 multi-colored Quick Connect

Spraytips

* HandleFasteningHardwareKit (whichincludes):

* CarriageBolts (4)

* Plastic Knobs (4)

, TreeClips (4)

Becomefamiliar with eachpiecebefore assemblingthe

pressure washer. Identify all contents with the illustration on

page 6. if any parts are missing or damaged,callthe

pressure washer helpline at 1-800-222-3136.

ASSEMBLINGPRESSUREWASHER

Your Craftsmanpressure washer will need assembly before

operation:

1. Fill out and send in registration card.

2. Attach handle,accessorytray and bottle brackets.

3. Add oil to engine crankcase.

4. Add fuel to fuel tank.

5. Connectpressure hoseto spray gun and pump.

6. Connectwater supply to pump.

NOTE:It may be necessaryto move the handle supports

from sideto side in order to align the handle so it will slide

overthe handlesupports.

2. Insert carriagebolts (D) through holes from back of unit

and attacha plastic knob (E)from front of unit. Tighten

by hand.

3. Placeaccessorytray (F) over holes (6) on handle

(viewing from front of unit). Pushthe tree clips (H) into

the holes until they sit flat againstthe accessorytray.

Insert multi-colored Quick Connectspray tips and other

supplied accessories in spaces provided in accessory

tray. SeeHow to UseAccessory Tray.

5. Attach bottle bracket (A) to handlewith carriagebolt (B)

and black plastic knob (C). Tighten by hand.

2-1N-1SOAPSYSTEM

Thepressure washer is equipped with two detergent

siphoning hoses.

Standard Clear Siphon Tube

Cleartube with filter:

Whenusingtheclearsiphontube,dilute

1partconcentrateto 16partswater

(4 ozof standardconcentratemakes

1/2Cationofmix.)

Project Pro÷ PerfectMW" Siphon

Blue tube with blue bottle cap:

WhenusingthebluePerfectMi/'_siphon,

usetheconcentratestraightfrom thebottle

(Onequartbottleof PerfectMixTM concentrate

makes4.25gaflonsofsoapspray.)

AttachProjectPro®PerfectMixTM Siphonto Pump

Attachthe hoseend of the blue Project Pro®PerfectMixTM

Siphon (D)to the barbed hosefitting (E) on the pump.

Attach PerfectMix,, Detergent Siphon

to Concentrate BottJe

PlaceProject Pro®PerfectMixTM bottle (not included) in the

wire-form bracket on the handle.Removecap from bottle

and insert the Project Pro®PerfectMixTM Siphon (F). Screw

the siphon unit to the top of the bottle (6). Usethe clip on

the cap (F) to snapsiphon to wire form bracketwhen siphon

is not in a concentrate bottle.

AddEngineOil

1. Placepressure washer on a flat, levelsurface.

2. Cleanareaaround oil fill and removeyellow oil fill cap.

3. Using oil funnel (optional), slowly pour contents of

provided oil bottle into oil fill opening to the point of

overflowing.

NOTICE

Improper treatment of pressure washer can damageit and

shorten its life.

DONOTattemptto crankor starttheenginebeforeit hasbeen

properlyservicedwiththerecommendedoil.Thismayresultin

anenginefailure.

4. Replaceoil fill cap and fully tighten.

AddFuel

Fuel must meet theserequirements:

* Clean,fresh, unleadedgasoline.

, A minimum of 87 octane/B7AKI (91 RON).High altitude

use, seeHigh Altitude.

* Gasolinewith up to 10% ethanol (gasohol) or upto 15%

MTBE(methyl tertiary butyl ether) is acceptable.

NOTICE

Avoid pressure washer damage.

Failureto follow Operator's Manualfor fuel

recommendations voids warranty.

DONOTuseunapprovedgasolinesuchasE85.

DONOTmixoil in gasoline.

DONOTmodifyengineto runon alternatefuels.

Toprotectthefuelsystemfromgumformation,mixinafuel

stabilizerwhenaddingfuel.SeeStorage.All fuel is not the

same. If you experiencestarting or performanceproblems

after using fuel, switch to a different fuel provider or change

brands. This engine is certified to operateon gasoline. The

emission control system for this engine is EM (Engine

Modifications).

WARRIRG

Fueland its vapors are extremely flammable and

explosive.

Fireor explosion can causesevere burns or

death.

WHENADDING FUEL

• Turn pressure washer OFFand let it cool at least 2 minutes

before removing fuel cap. Loosen cap slowly to relievepressure

in tank.

• Fill fuel tank outdoors.

, DONOToverfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporatesbefore starting engine.

, Keepfuel away from sparks, openflames, pilot lights, heat,and

other ignition sources.

, DONOTlight a cigarette or smoke.

Cleanarea around fuel fill cap, remove cap.

Slowly add regular unleadedfuel (A) to fuel tank (B). Be

careful notto overfill. Allow about 1.5" (4cm) (C) of tank

spacefor fuel expansion.

3. Installfuel capand wait for any spilled fuel to evaporate.

CAUTION!Alcohol-blended fuels (calledgasohol, ethanol or

methanol) can attract moisture, which leadsto separation and

formation of acids during storage.Acidic gascan damagethe

fuel system of an enginewhile in storage.

Toavoidengineproblems,the fuel systemshouldbetreated

with afuel preserver or emptied beforestorageof 30 daysor

longer.If adding a fuel preserver,fill the fuel tank with fresh

fuel. If only partially filled, air in the tank will promote fuel

deterioration during storage. If fuel preserver is not used,

drainthe fueltank, startthe engineand let it run untilthe fuel

linesand carburetorareempty. Usefresh fuelnext season.See

Storagefor additionalinformation.

NEVERuseengine or carburetor cleanerproducts in the fuel

tank as permanent damagemay occur.

HighARRude

At altitudes over5,000 feet (1524 meters), a minimum

85 octane/ 85 AKI (89 RON)gasoline is acceptable.To

remainemissions compliant, high altitude adjustment is

required. Operationwithout this adjustment will cause

decreasedperformance, increased fuel consumption, and

increasedemissions. Seea qualified Searsdealerfor high

altitude adjustment information. Operationof the engine at

altitudes below 2,500 feet (762 meters)with the high altitude

kit is not recommended.

Connect Hose and Water Supply to Pump

[ ROTICE

DONOTrun the pump without the water supply connected

and turned on.

L amageto equipmentresultingfrom failureto followthis

instructionwillvoidwarranty.

NOTE:Removeand discardthe shipping caps from the

pump's high pressure outlet and water inlet beforeattaching

hoses.

1. Uncoil high pressure hose and attach one end of hoseto

baseof spray gun. Tighten by hand.

WARRIRG

he high pressurestream of water that this

quipment produces cancut through skin and its

nderlying tissues, leadingto serious injury and

ossible amputation.

NEVERconnecthighpressurehoseto spraytip extension.

Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

Alwaysbecertainspraygun,spraytipsandaccessoriesare

correctlyattached.

2. Attach other end of high pressure hoseto high pressure

outlet on pump. Tighten by hand.

Beforeconnectinggarden hoseto water inlet, inspect

inlet screen.Cleanscreen (A) if it contains debris or have

it replacedif damaged.DONOTrun pressurewasher if

inlet screenis damagedor missing.

4. Run water through garden hose for 30 secondsto flush

it of debris. Turn off water.

IMPORTANT:DONOTsiphon standing water for the water

supply. UseONLYcold water (less than IO0°F).

5. Connectgarden hose (not to exceed50 feet in length) to

water inlet. Tighten by hand.

NOTICE

Using a OneWay Valve(vacuum breakeror check valve)

at pump inlet cancause pump or inlet connector damage.

ThereMUSTbeatleasttenfeet(3m)of unrestrictedgarden

hosebetweenthepressurewasherinletandanydevice,suchas

avacuumbreakeror checkvalve.

Damagetoequipmentresultingfromfailuretofollowthis

instructionwillvoidwarranty.

6. Turn ONthe water,press red button (B) on the gun and

squeezethe trigger to purge the pump system of air and

impurities.

WARHIHG

_Risk of injury.

eye

ISpray cansplash back or propel objects.

Alwayswearsafetygoggleswhenusingthis equipmentor in

vicinityof whereequipmentisin use.

Beforestartingthepressurewasher,besureyouarewearing

adequatesafetygoggles.

NEVERsubstitutesafetyglassesfor safetygoggles.

CheckJistBeforeStartingEngine

Reviewthe unit to ensureyou have performed all of the

following:

1. Besure to read SafetyRules and Operationsections

before usingthe pressure washer.

2. Makesure handle is in placeand secure.

3. Checkthat oil has beenadded to proper levelin engine

crankcase.

4. Add proper fuelto fuel tank.

5. Checkfor proper hoseconnections (high pressure and

water supply) and that there are no kinks, cuts, or

damageto the high pressure hose.

6. Provideproper water supply (not to exceedIO0°F).

HOWTOUSEYOURPRESSUREWASHER

If you haveany problems operatingyour pressure washer,

pleasecallthe pressure washer helpline at 1-800-222-3136.

Pressure Washer Location

PressureWasherClearance

,_ WARNING

_ Exhaustheat/gases can ignitecombustibles,

structures or damagefuel tank causing a fire.

* Keepatleast5ft. (152cm)clearanceonall sidesofpressure

washerincludingoverhead.

Placepressure washer outdoors in an areathat will not

accumulate deadlyexhaustgas. DONOTplacepressure

washer where exhaustgas (A) could accumulateand enter

inside or be drawn into a potentially occupied building.

Ensureexhaustgas is kept awayfrom any windows, doors,

ventilation intakes, or other openingsthat can allow exhaust

gasto collect in a confined area. Prevailingwinds and air

currents should be taken into considerationwhen positioning

_ressurewasher.

,_ WARHJHG

Runningengine gives off carbon monoxide, an

odorless, colorless, poison gas.

_ reathingcarbon monoxide can causeheadache,

fatigue, dizziness,vomiting, confusion, seizures,

nausea,fainting or death.

. OperatepressurewasherONLYoutdoors.

. Keepexhaustgasfromenteringaconfinedareathrough

windows,doors,ventilationintakes,or otheropenings.

• DONOTstartor runengineindoorsor in anenclosedarea,

evenif windowsanddoorsareopen.

To Start Your Pressure Washer

To start your engine-powered pressurewasher for the first

time, follow these instructions step-by-step. This information

also applies wheneveryou start the engine after you havelet

the pressure washer sit idle for at leasta day.

1. Placepressure washer nearan outside water source

capableof supplying water at a flow rategreater than

3.8 gallons per minute and no less than 20 PSIat

pressurewasher end of garden hose.

2. Checkthat high pressure hose istightly connectedto

spray gun and pump. SeeAssemblyfor illustrations.

3. Makesure unit is in a levelposition.

4. Connectgarden hoseto water inlet on pressure washer

pump.

5. Turn ONthe water,press red button on the gun and

squeezethe trigger to purge the pump system of air and

impurities.

[ NOTICE

DONOTrun the pump without the water supply connected

and turned on.

L amageto equipmentresultingfrom failureto followthis

instructionwillvoidwarranty.

6. Attach spray tip extensionto spray gun. Tighten by

hand.

7. ChooseQuick Connectspraytip you want to use, pull

back on collar of spray tip extension, insert spray tip and

releasecollar. Tug on spray tip to make sure it is

securely in place. SeeHow to Use OuickConnectSpray

tip System.

8. Rotate fuelshut-off valveto "On"position (B) (fully

counter-clockwise).

9. Move throttle lever (A) to "Fast" position, shown here as

a rabbit.

10. Move choke lever (B) to "Choke" position.

NOTE:Fora warm engine, be surethe choke lever is in the

"Run" position.

IMPORTANT:Beforestarting the pressure washer, be sure

/ou are wearing adequatesafety goggles.

WARNING

>_ Risk of eyeinjury.

_Spray cansp ash back or propel objects.

Alwayswearsafetygoggleswhenusingthis equipmentor in

vicinityofwhereequipmentisin use.

Beforestartingthepressurewasher,besureyouarewearing

adequatesafetygoggles.

NEVERsubstitutesafetyglassesforsafetygoggles.

1. Whenstarting engine, position yourself as

recommended, grasp handle and pull recoil starter

lightly until you feel some resistance,then pull briskly.

WARNING

Starter cord kickback(rapid retraction) can result

in bodily injury. Kickbackwill pull handand arm

___ toward enginefaster thanyou canlet go.

Brokenbones, fractures, bruises, or sprains

could result.

• NEVERpullstartercordwithoutfirst relievingspraygun

pressure.

• Whenstartingengine,pullcordslowlyuntilresistanceisfelt

andthenpullrapidlyto avoidkickback.

, Aftereachstartingattempt,whereenginefailsto run,always

pointspraygunin safedirection,pressredbuttonandsqueeze

sprayguntriggerto releasehighpressure.

, Firmlygraspspraygunwith bothhandswhenusinghigh

pressuresprayto avoidinjurywhenspraygunkicksback.

12. Return recoil starter slowly. DONOTlet rope "snap

back"against starter.

13. When engine starts, slowly movechoke leverto "Run"

position, as engine warms. If engine falters, move choke

leverto "Choke" position, then to "Run" position.

14. After eachstarting attempt, where enginefails to run,

always point gun in safe direction, press red button and

squeezespray gun trigger to releasehigh pressure.

Move choke leverto "Choke" position, and repeatsteps

11 through 13.

15. If enginefails to start after six pulls, movechoke leverto

"Run" position, and repeatsteps 11 through 13.

NOTE:Always keepthe throttle lever in the "Fast" position

when operatingthe pressure washer.

WARNING

Thehigh pressurestream of water that this

equipment produces cancut through skin and its

_ nderlying tissues, leadingto serious injury and

)ossible amputation.

Spray gun traps high water pressure,evenwhen

engine is stopped and water is disconnected,

which can cause injury.

, DONOTallowCHILDRENtooperatepressurewasher.

* Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

* NEVERaimspraygunatpeople,animals,or plants.

, DONOTsecurespraygun inopenposition.

* DONOTleavespraygununattendedwhilemachineis running.

, NEVERusea spraygunwhichdoesnothaveatriggerlockor

triggerguardin placeandin workingorder.

, Alwaysbecertainspraygun,spraytipsandaccessoriesare

correctlyattached.

WARHIHG

s_ Contact with muffler result in serious

area can

burns.

f_ Exhaustheat/gases can ignite combustibles,

structures or damagefuel tank causing a fire.

* DONOTtouchhotpartsandAVOIDhotexhaustgases.

* Allowequipmentto coolbeforetouching.

Keepatleast5feet (152cm) ofclearanceonall sidesof

pressurewasherincludingoverhead.

* Codeof FederalRegulation(CFR)Title36Parks,Forests,and

PublicPropertyrequireequipmentpoweredbyaninternal

combustionengineto haveasparkarrester,maintainedin

effectiveworkingorder,complyingto USDAForestservice

standard5100-1Corlaterrevision.IntheStateofCaliforniaa

sparkarresteris requiredundersection4442oftheCalifornia

Publicresourcescode.Otherstatesmayhavesimilarlaws.

How to Stop Your Pressure Washer

1. Releasespray gun trigger and letengine idle for two

minutes.

2. Move throttle to SLOWposition, then STOPposition.

WARNING

f_j Backfire,fire or engine damagecould occur.

DONOTstopenginebymovingchokeleverto "Cheke"position.

3. ALWAYSpoint spray gun in a safe direction, press red

button and squeezespray gun trigger to releaseretained

high water pressure.

IMPORTANT:Spraygun traps high water pressure,even

when engine is stopped and water is disconnected.

WARHIHG

The high pressure stream of water that this

equipment produces cancut through skin and its

_ nderlying tissues, leadingto serious injury and

_ossibleamputation.

Spray gun traps high water pressure,evenwhen

engine is stopped and water is disconnected,

which can cause injury.

. Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

* ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntrigger,to releasehighpressure,every

time youstopengine.

How to Use Accessory Tray

Theunit is equipped with an accessorytray with placesto

store your QuickConnectspray tips, spray gun and spray tip

extension. Thereis also a hook atthe front of the accessory

tray to hold your high pressure hose. Identify all accessories

with the illustration on page6.

NOTE:The extra hole in the tray is for storing a utility brush.

Theextra clip in the tray is for storing a turbo spray tip. The

brush and turbo spray tip are NOTincluded with your

pressure washer. You can buythese items as optional

accessories.

1. Placespray tip extensionthrough hole on accessory

tray, as shown.

Placespray gun through hole on accessorytray on right

side of unit.

Insert multi-colored Quick Connectspray tips in spaces

provided in accessorytray.

Hanghigh pressure hose on hook attachedto accessory

tray on front of tray as shown.

How to Use Spray Tips

Thequick-connect on the spray tip extensionallows you to

switch between four different quick connect spray tips. Spray

tips can be changedwhile pressure washer is running once

spray gun trigger lock is engaged.Thespray tips vary the

spray pattern asshown on next page.

Followthese instructionsto changespraytips:

1. Puil backcollar on quick-connect and pull current spray

tip off. Storespray tips in holder provided on accessory

tray.

WARNING

Thehigh pressurestream of water that this

:_ equipment produces cancut through skin and its

underlyingtissues, leadingto serious injury and

)ossible amputation.

NEVERexchangeQuickConnectspraytips withoutthetrigger

lockedonthespraygun.

DONOTtwist QuickConnectspraytips whilespraying.

2. 2-IH-1 SOAPSYSTEM

Select desiredspray tip:

Low Pressure

Black

Useto apply

chemical

High Pressure

40° White 15° Yellow 0° Red

2550 PSI 2800 PSI 3100 PSI

2.3 GPM 2.7 GPM 2.8 GPM

* Fordelicate rinse (lower pressure and higher flow),

for gentlecleaning of cars/trucks, boats, RV's, patio

furniture, lawn equipment, etc., select white 40°

spray tip.

* Forgeneral rinsing (medium pressure and medium

flow), ideal for most all purposecleaning such as

home siding, brick patios, wood decks, driveways

and sidewalks,garage floors, etc., select yellow

15° spray tip.

* Formaximum rinsing (higher pressure and lower

flow), for stubborn or hard to reachsurfacesuch as

second story surfaces,paint removal,oil stains, rust

removalor other stubborn substances (tar, gum,

grease,wax, etc.), select red 0° spraytip.

, To apply detergent,applies project specific cleaners

to help breakdown stubborn dirt and grime on a

variety of surfaces, select black detergentspray tip.

Pull backon collar,insert newspraytip and releasecollar.

Tugon spraytip to makesureit is securelyin place.

UsageTips

* Formost effective cleaning, keepspray tip from 8 to

24 inches (20 to 61 cm) awayfrom cleaning surface.

, If you get spray tip too close, especiallyusing a high

pressure spray tip, you may damagesurface being

cleaned.

, DONOTget closer than 6 inches (15 cm) when cleaning

tires.

CAUTION

Chemicalscan cause bodily injury, and/or property

damage.

NEVERusecausticliquidwith pressurewasher.

UseONLYpressurewashersafedetergents/soaps.Followall

manufacturersinstructions.

Cleaning and Applying Detergent with

the Project Pro®PerfectMix TM Siphon

Tn applyundiluteddetergent using

the bluePerfectMix" siphnn,

felJnw these steps:

1. Reviewuseof black spray tip.

2. Attach PerfectMixTM siphon hoseto

pump and PerfectMixTM Extreme

Concentratebottle.

3. Makesure black spray tip is installed.

NOTE:Detergentcannot be applied with the

high pressurespray tips (Yellow, White or Red).

Makesure garden hose is connectedto water inlet.

Checkthat high pressure hose is connectedto spray gun

and pump. Turn on water.

NOTICE

You must attachall hosesbefore you start the engine.

Startingtheenginewithoutallthehosesconnectedandwithout

thewaterturnedONwill damagethepump.

Damageto equipmentresultingfrom failureto followthis

instructionwillvoidwarranty.

5. Start engine following instructions How to Start Your

Pressure Washer.

6. Placethreadedend of detergent siphoning tube into

ExtremeConcentratedetergentcontainer. Tighten by

hand.

7. Apply detergentto a dry surface, starting at lower

portion of areato be washed and work upward, using

long, even, overlappingstrokes.

8. Allow detergentto "soak in"for 3-5 minutes before

washing and rinsing. Reappiyas neededto prevent

surface from drying. DONOTallow detergent to dry on

(preventsstreaking).

Forbest results, scrub the detergent covered surfaceto help

removestubborn dirt, grime and stains. Forvehicles, usea

soft car wash brush or mitt. Fordecking, siding and

concrete, usea brush appropriate for the type of surface

being cleaned.

IMPORTANT:You must flush the detergent siphoning system

after eachuse by placing the filter into a bucketof clean

water, then run the pressure washer in low pressurefor 1-2

minutes.

Cleaning and Applying Detergent with

the Standard Clear Siphon

To apply diluteddetergent usingthe

standardcJearsiphontube,

folJowthesesteps:

1. Reviewuse of black spray tip.

2. Attachclear siphon hoseto pump.

3. Mix detergent solution as required byjob.

4. Placesmall filter end of clearsiphoning tube into

container with diluted solution as described above.

NOTICE

Contact with the hot muffler can damagedetergent

siphoning tube.

Wheninsertingthesiphonintoa detergentsolutionbottle,

routethetubesoasto keepitfrom inadvertentlycontactingthe

hotmuffler.

NOTE:Makesure the filter is fully submerged in fluid while

applying solution.

5. Make sure black spray tip is installed.

NOTE:Detergentcannot be applied with the high pressure

spray tips (Yellow, White or Red).

6. Make sure garden hoseis connectedto water inlet.

Checkthat high pressure hose is connectedto spray gun

and pump. Turn on water.

NOTICE

You must attachall hosesbefore you start the engine.

Startingtheenginewithoutallthehosesconnectedandwithout

thewaterturnedONwill damagethepump.

Damageto equipmentresultingfrom failureto followthis

instructionwillvoidwarranty.

7. Start engine following instructions How to Start Your

Pressure Washer.

8. Apply detergentto a dry surface, starting at lower

portion of areato be washed and work upward, using

long, even, overlappingstrokes.

9. Allow detergentto "soak in"for 3-5 minutes before

washing and rinsing. Reapplyas neededto prevent

surface from drying. DONOTallow detergent to dry on

(preventsstreaking).

Forbest results, scrub the detergent covered surfaceto help

removestubborn dirt, grime and stains. Forvehicles, usea

soft car wash brush or mitt. Fordecking, siding and

concrete, usea brush appropriate for the type of surface

being cleaned.

IMPORTANT:You must flush the detergent siphoning system

after eachuse by placing the filter into a bucketof clean

water, then run the pressure washer in low pressurefor 1-2

minutes.

PressureWasherRinsing

ForRinsing:

1. Removesoapspray tip from spray tip extension.

2. Selectand install desiredhigh pressurespray tip

following instructions How to Use Ouick ConnectSpray

tip System.

3. Keepthe spray gun a safe distance from the areayou

plan to spray.

WARHIHG

spray gun can cause you

Kickbackfrom to fall.

• Operatepressurewasherfrom astablesurface.

, Beextremelycarefulif youmustusethepressurewasherfrom

a ladder,scaffolding,or anyothersimilarlocation.

, Firmlygraspspraygunwith bothhandswhenusinghigh

pressuresprayto avoidinjurywhenspraygunkicksback.

4. Apply a high pressure spray to a small area,then check

the surfacefor damage.If no damageis found, it is okay

to continue cleaning.

Start at the top of the areato be rinsed, working down

with same overlapping strokes asyou usedfor washing

and applying detergent.

Cleaning DetergentSiphoning Tube

If you usedthe clear detergent siphoning tube, you must

flush it with cleanwater beforestopping the engine.

1. Placedetergent siphoning tube/filter in a bucketfull of

clean water.

2. Removehigh pressurespray tip from spray tip

extension.

3. Selectand install a soap spray tip following instructions

How to Use Ouick ConnectSpray Tips.

4. Flushfor 1-2 minutes.

5. Shut off engine following instructions How to Stop

Pressure Washerand turn off water supply.

6. ALWAYSpoint spray gun in a safe direction push red

button and squeezespray gun trigger to releaseretained

high water pressure.

WARHIHG

The high pressure stream of water that this

_ equipment produces can cut through skin and its

lunderlying tissues, leading to serious injury and

ipossible amputation.

• Keephigh pressure hoseconnected to pump and spray gun

while system is pressurized.

• ALWAYSpoint spraygun in safe direction, press red button and

squeezespray gun trigger, to releasehigh pressure, everytime

you stop engine.

iMPORTANT:Spraygun traps high water pressure,even

when engine is stopped and water is disconnected.

Automatic Cool Down System (Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun,

circulating water in the pump can reachtemperatures above

125°F.Thesystem engagesto cool the pump by discharging

the warmwater onto the ground.

EHGINETECHNICALINFORMATIOH

This is a single cylinder, overheadvalve (OHV),air cooled

engine. It is a low emissions engine.

Inthe Stateof California, ModelSeries 120000 enginesare

certified by the CaliforniaAir ResourcesBoardto meet

emissions standardsfor 125 hours. Suchcertification does

not grant the purchaser,owner or operator of this engine any

additional warranties with respectto the performance or

operational life of this engine.Theengine is warranted solely

according to the product and emissions warranties stated

elsewherein this manual.

Power Ratings

Thegross power rating for individual gas engine models is

labeledin accordancewith SAE(Societyof Automotive

Engineers)codeJ1940 (Small Engine Power & Torque

Rating Procedure),and rating performance hasbeen

obtained andcorrected in accordancewith SAEJ1995

(Revision2002-05). Torquevalues are derived at3060 RPM;

horsepower values are derivedat 3600 RPM.Actual gross

engine power will be lower and is affected by, among other

things, ambient operating conditions and engine-to-engine

variability. Givenboth the wide array of products on which

enginesare placedand the variety of environmental issues

applicableto operatingthe equipment, the gas engine will not

developthe ratedgross power when used in a given pieceof

power equipment (actual "on-site"or net power). This

difference is due to a variety of factors including, but not

limited to, accessories (air cleaner, exhaust,charging,

cooling, carburetor, fuel pump, etc.), application limitations,

ambient operating conditions (temperature,humidity,

altitude), and engine-to-engine variability. Dueto

manufacturing and capacity limitations, Briggs & Stratton

maysubstitute an engine of higher ratedpower for this

Seriesengine.

This pressurewasher is rated in accordanceto the Pressure

Washer Manufacture Association (PWMA) standard PW101

(Testingand Rating Performanceof PressureWashers).

PRODUCTSPECIFICATJOHS

Pressure Washer Specifications

Max Outlet Pressure ....................... 3,100 PSi

Max How Rate............................. 2.8 GPM

DetergentMix ........................ Use asdirected

Water SupplyTemperature .......... Not to exceed IO0°F

Engine Specifications

Bore ................................ 2.672 in.(68mm)

Stroke .............................. 2.204 in.(56mm)

Displacement ........................ 12.48in.(206 cc)

SparkPlug

ResistorType: ............. Briggs & Stratton 491055S

Long Life Platinum: .......... Briggs & Stratton 5066D

SetGapTo: ...................... O.030inch(0.76ram)

ArmatureAir Gap: ........... 0.010-0.014in.(O.25-O.36mm)

Valveclearancewithvalvespringsinstalledand piston1/4in.

(6 ram)pasttopdeadcenter(checkwhenengineiscold).

Intake.................... 0.004-0.006in.(0.10-0.15mm)

Exhaust .................. 0.009-0.011in.(0.23-0.28mm)

FuelCapacity............................... 1.6Quarts

OilCapacity........................ 20 Ounces(0.6 liter)

NOTE:Forpractical operation, the engine load should not

exceed 85% of rated power. Enginepower will decrease

3-1/2% for each1,000 feet (300 meters) abovesea leveland

1% for each 10° F(5.6° C) above77° F(25° C). It should

operatesatisfactorily at an angle up to 15°.

GENERALRECOMMENDATiOHS

Follow the hourly or calendarintervals,whichever occurs

first. More frequent service is required when operating in

adverseconditions noted below.

Pump Oil

DONOTattempt any oil maintenanceon this pump. The

pump is pre-lubricated and sealedfrom the factory, requiring

no additional maintenancefor the life of the pump.

* Changeengine oil

* Check/clean water inlet screen1

* Checkhigh pressure hose

* Checkdetergentsiphoning hose

* Checkspray gun and assemblyfor leaks

* Cleandebris

* Checkengine oil level

* Serviceengine air cleaner_

* Changeengine oiF

* Servicespark arrester

* Servicespark plug

* Cleancooling system2

' Clean if clogged. Replaceif perforated or torn.

Service more often under dirty or dusty conditions.

General Recommendations

Regularmaintenancewill improve the performanceand

extendthe life of the pressure washer.Seeany Searsor

other qualified service dealerfor service.

Thepressure washer warranty doesnot cover items that

havebeensubjected to operator abuseor negligence.To

receivefull valuefrom the warranty, the operator must

maintain pressurewasher as instructed in this manual

including proper storage asdetailed in Storage.

Someadjustments will needto be madeperiodically to

properly maintainyour pressure washer.

All service and adjustments should be madeat least once

eachseason.Follow the requirementsin the Maintenance

Schedulechart above.

NOTE:Oncea yearyou should clean or replacethe spark

plug and replacethe air filter. A new spark plug and clean air

filter assure proper fuel-air mixture and helpyour engine run

better and last longer.

Emissions Control

Maintenance, replacement,or repair of the emissions

controldevicesand systemsmay be performedby any non-

roadengine repair establishmentor individual. However,

to obtain "no charge" emissions control service, the work

must be performed by a factory authorized dealer.Seethe

Emissions Warranty.

Refore Each Use

1. Checkengine oil level.

2. Cleandebris.

3. Checkwater inlet screenfor damage.

4. Checkhigh pressure hose for leaks.

5. Checkgun and spray tip extensionassembly for leaks.

6. Purgepump of air and contaminants.

PRESSUREWASHERMAINTENANCE

Clean Debris

Daily or before use,clean accumulated debris from pressure

washer. Keeplinkage, spring and controls clean. Keeparea

around and behind muffler free from anycombustible debris.

Inspect cooling air slots and openings on the pressure

washer. Theseopenings must be kept cleanand

unobstructed.

Pressurewasher parts should be kept cleanto reducethe

risk of overheating and ignition of accumulated debris.

* Usea dampcloth to wipe exterior surfaces clean.

* Usea soft bristle brushto loosencaked on dirt, oil, etc.

[ NOTICE

Improper treatment of pressure washer can damageit and

[shorten ts fe.

E DONOTinsertanyobjectsthroughcoolingslots.

* Usea vacuumcleanerto pick up loosedirt anddebris.

Check and Clean Inlet Screen

Examinegarden hose inlet screen. Cleanif it is clogged or

replaceif it is torn.

Check High Pressure Hose

Highpressure hoses can developleaksfrom wear, kinking,

or abuse. Inspecthosebefore eachuse. Checkfor cuts,

leaks,abrasions, bulging of cover, or damageor movement

of couplings. If any ofthese conditions exist, replacehose

immediately.

WARNING

_! pressure stream of water that th_

nt produces cancut through skin and its

ng tissues, leadingto serious injury and

amputation.

NEVERrepairhighpressurehose.Replaceit.

ReplacementhoseratingMUSTexceedmaximumpressure

ratingof unit.

Check Detergent Siphoning Tube

Examinethe filter on the detergent tube andclean if clogged.

Thetube should fit tightly on the barbed fitting. Examinethe

tube for leaks or tears. Replacethe filter or tube if either is

damaged.

Check Gun and Spray Tip Extension

Examinethe hose connectionto the spray gun and make

sure it is secure.Testthe trigger by pressing the red button

and making surethe trigger "springs back" into placewhen

you releaseit. You should not be able to press the trigger

without pressing the red button. Replacespray gun

immediately if it fails any ofthese tests.

Spray Tip Maintenance

A pulsing sensationfelt while squeezingthe spray gun trigger

may becaused by excessivepump pressure. Theprincipal

cause of excessivepump pressure is a spray tip clogged or

restricted with foreign materials, such asdirt, etc. Tocorrect

the problem, immediately cleanthe spray tip following these

instructions:

Shut off engine and turn off water supply.

ALWAYSpoint spray gun in a safe direction, press red

button and squeezespray gun trigger to releaseretained

high water pressure.

WARNING

Thehigh pressure stream of water that this

equipment produces can cut through skin and its

_ nderlying tissues, leading to serious injury and

)ossible amputation.

Spraygun traps high water pressure, evenwhen

engine is stopped and water is disconnected,

which cancause injury.

• Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

. ALWAYSpointspraygunin safedirection,pressred button

andsqueezesprayguntrigger,to releasehighpressure,every

timeyoustop engine.

Removespray tip from end of spray tip extension.

Usea small paperclip to free any foreign material

clogging or restricting spray tip (A).

Removespray tip extensionfrom spray gun.

Using a garden hose, removeadditional debris by back

flushing water through spray tip extension. Backflush

between30 to 60 seconds.

10.

11.

Reinstallspray tip into spray tip extension.

Reconnectspray tip extensionto spray gun.

Makesure garden hose is connectedto water inlet.

Checkthat high pressure hose is connectedto spray gun

and pump. Turn on water.

Start engine following instructions How to Start Your

Pressure Washer.

Test pressure washer by operating with eachquick

connect spray tip.

O-Ring Maintenance

Purchasean O-Ring RepairKit atyour local Searsor by

calling 1-800-4-NIY-HOME(469-4663) or online at

www.sears.com. It is not included with the pressure washer.

This kit includes replacemento-rings, rubber washer and

water inlet filter. Referto the instruction sheet provided in the

kit to serviceyOUrunit's o-rings.

WARNING

Thehigh pressurestream of water that this

_ quipment produces cancut through skin and itsunderlyingtissues, leadingto serious injury and

_ossibleamputation.

• NEVERrepairleakingconnectionswithsealantof anykind.

Replaceo-ringor seal.

ENGINEMAINTENANCE

WARHIHG

_ Unintentionalsparking can result in fire or

_¢ electric shock.

WHENADJUSTINGORMAKINGREPAIRSTOYOURPRESSURE

WASHER

* Disconnectthesparkplugwirefromthesparkplugandplace

thewirewhereit cannotcontactsparkplug.

WHENTESTINGFORENGINESPARK

* Useapprovedsparkplugtester.

, DONOTcheckfor sparkwith sparkplugremoved.

Oil

OiiRecemmendations

We recommendthe useof Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptableif classified for service SF,SG,

SH, SJ or higher. Do not usespecial additives.

Outdoortemperatures determine the proper oil viscosity for

the engine. Usethe chart to selectthe best viscosity for the

outdoor temperature rangeexpected.

; i°

* Below40%(4°C)theuseofSAE30will resultin hardstarting.

** Above80°F(27°C)theuseof10W30maycauseincreasedoil

consumption.Checkoil levelmorefrequently.

NOTE:Synthetic oil meeting ILSACGF-2,API

certification mark and API servicesymbol with

"SJ/CF ENERGYCONSERVING"or higher, is an

acceptableoil at all temperatures. Useof synthetic oil

doesnot alter required oil change intervals.

CheckingOilLevel

Oil level should be checked prior to each useor at least every

8 hours of operation. Keepoil levelmaintained.

1. Make sure pressure washer is on a level surface.

2. Removeoil fill cap and wipe cleanwith cloth.

3. Verify oil is at the point of overflowing at oil fill opening.

Replaceand tighten oil fill cap.

AddingEngineOil

1. Makesure pressure washer is on a levelsurface.

2. Checkoil level as described in CheckingOffLevel

3. If needed,slowly pour oil into oil fill openingto the point

of overflowing at oil fill cap.

4. Replaceand tighten oil fill cap.

ChangingEngineOil

Changeengine oil after the first 5 hours and every 50 hours

thereafter. If you are using your pressure washer under

extremely dirty or dusty conditions, or in extremely hot

weather, changeoil more often.

CAUTION

Avoid prolonged or repeatedskin contact with used motor

oil.

Usedmotoroil hasbeenshownto causeskincancerin certain

laboratoryanimals.

Thoroughlywashexposedareaswith soapandwater.

KEEPOUTOFREACHOFCHILDREN.DON'T

POLLUTE.CONSERVERESOURCES.RETURN

USEDOILTOCOLLECTIONCENTERS.

Changeoil while engineisstillwarmfrom running,asfollows:

1. Makesure unit is on a levelsurface.

2. Disconnectthe spark plug wire from the spark plug and

placethe wire where it cannot contact spark plug.

3. Cleanareaaround oil drain plug (A). Theoil drain plug is

locatedat baseof engine, opposite carburetor.

4. Removeoil drain plug and drain oil completely into a

suitable container.

5. Reinstalloil drain plug and tighten securely. Removeoil

fill cap.

6. Slowly pour oil (about 20 oz.) into oil fill opening (B) to

the point of overflowing (C)at oil fill cap.

7. Reinstalloil fill cap. Fingertighten capsecurely.

8. Wipe up anyspilled oil.

Page is loading ...

Craftsman 580.752290 Owner's manual

Brand: Craftsman

Model: 580.752290

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

580752290

Download PDF

report

in other languages

español: Craftsman 580.752290 El manual del propietario

Craftsman 580.752290 Owner's manual

This manual is also suitable for

Craftsman 580.752290 Owner's manual

in other languages

Related papers

Other documents