MTD PS720r User manual

Category
Power chainsaws
Type
User manual
Operator’s Manual
IMPORTANT: READ SAFETY RULES
AND INSTRUCTIONS CAREFULLY
P/N 9096-A10708
© 2005
PRINTED IN T
AIW
AN
Pole Saw
PS720r
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
2
INTRODUCTION
Copy the serial number
her
e:
THANK YOU
Thank you for buying this quality product. This modern
outdoor power tool will provide many hours of useful
service. You will find it to be a great labor-saving device.
This operator’s manual provides you with easy-to-
understand operating instr
uctions. Read the whole
manual and follow all the instr
uctions to keep your new
outdoor power tool in top operating condition.
PRODUCT REFERENCES, ILLUSTRATIONS
AND SPECIFICATIONS
All information, illustrations, and specifications in this
manual are based on the latest product information
available at the time of printing. We reserve the right to
make changes at any time without notice.
Copyright© 2004 MTD SOUTHWEST INC, All Rights
Reserved.
SERVICE INFORMATION
Service on this unit both within and after the warranty
period should be performed only by an authorized and
approved service dealer.
For service call
1-800-345-8746 to obtain a list of
authorized service dealers near you. For more details
about your unit, visit our website at
www.TrimmerPlus.com.
If you have difficulty assembling this product or have any
questions regarding the controls, operation or
maintenance of this unit, please call the Customer
Support Department.
DO NOT RETURN THE UNIT TO THE RETAILER.
PROOF OF PURCHASE WILL BE REQUIRED FOR
W
ARRANTY SERVICE.
Make sure you carefully read and understand this manual
befor
e starting or operating this equipment.
THIS PRODUCT IS COVERED BY ONE OR MORE U.S.
PATENTS. OTHER PATENTS PENDING.
S/N :
ITEM :
MODEL :
TABLE OF CONTENTS
Intr
oduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . .3
Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . .8
Maintenance and Repair Instructions . . . . . . . . . . .11
Specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . .14
Parts List . . . . . . . . . . . . . . . . . . . .Inside Back Cover
Copy the model and parent
part number her
e:
Befor
e beginning, locate the unit’s model plate. It lists
the model and serial numbers of your unit. Refer to the
sample plate below and copy the information for future
reference.
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
3
RULES FOR SAFE OPERATION
SPECIAL SAFETY WARNINGS FOR GAS
POWERHEADS
Stor
e fuel only in containers specifically designed and
appr
oved for the storage of such materials.
Always stop the engine and allow it to cool before filling
the fuel tank. Never remove the cap of the fuel tank, or
add fuel, when the engine is hot. Never operate the unit
without the fuel cap securely in place. Loosen the fuel
tank cap slowly to relieve any pressure in the tank.
Mix and add fuel in a clean, well-ventilated area
outdoors where there are no sparks or flames. Slowly
remove the fuel cap only after stopping engine. Do not
smoke while fueling or mixing fuel. W
ipe up any spilled
fuel from the unit immediately.
Avoid creating a source of ignition for spilled fuel. Do
not star
t the engine until fuel vapors dissipate.
Move the unit at least 30 feet (9.1 m) fr
om the fueling
source and site before starting the engine. Do not
smoke. Keep sparks and open flames away from the
area while adding fuel or operating the unit.
Never start or run the unit inside a closed room or
building. Breathing exhaust fumes can kill. Operate this
unit only in a well ventilated area outdoors.
READ ALL INSTRUCTIONS
BEFORE OPERATING
Carefully read and understand the operator's manual of
the unit that powers this attachment.
Read this operating instr
uction manual car
efully
. Be
thoroughly familiar with the controls and the proper use
of the equipment. Know how to stop the unit and
disengage the controls quickly.
Do not operate this unit when tired, ill, or under the
influence of alcohol, drugs, or medication.
Never allow childr
en to operate the equipment. Never
allow adults unfamiliar with the instr
uctions to use the
unit. Never allow adults to operate the equipment
without pr
oper instr
uction.
All guar
ds and safety attachments must be installed
properly before operating the unit.
SYMBOL
MEANING
The purpose of safety symbols is to attract your
attention to possible dangers. The safety symbols,
and their explanations, deserve your careful attention
and understanding. The safety warnings do not by
themselves eliminate any danger
. The instructions or
warnings they give are not substitutes for proper
accident prevention measures.
NOTE: Advises you of infor
mation or instructions vital to
the operation or maintenance of the equipment.
SYMBOL
MEANING
• IMPORTANT SAFETY INSTRUCTIONS •
Failure to obey a
safety warning can
result in injury to yourself and others.
Always follow the safety precautions to
reduce the risk of fire, electric shock and
personal injury.
WARNING:
Failur
e to obey a
safety war
ning will
r
esult in serious injury to yourself or to
others. Always follow the safety pr
ecautions
to r
educe the risk of fire, electric shock and
personal injur
y.
DANGER:
Failure to obey a
safety warning may
result in property damage or personal injury
to yourself or to others. Always follow the
safety precautions to reduce the risk of fire,
electric shock and personal injury.
CAUTION:
Indicates
danger,
warning or caution. Attention is required in
order to avoid serious personal injury. May
be used in conjunction with other symbols
or pictographs.
SAFETY ALERT:
Read the Operator’
s Manual(s) and follow all
war
nings and safety instructions.
Failur
e to do so can result in serious injury to the
operator and/or bystanders.
FOR QUESTIONS, CALL 1-800-345-8746
When using the unit,
you must follow the
safety rules. Please read these instructions
before operating the unit in order to ensure the
safety of the operator and any bystanders.
Please keep these instructions for later use.
WARNING:
Gasoline is highly
flammable, and its
vapors can explode if ignited. T
ake the
following precautions:
WARNING:
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
4
POLE SAW OPERATING PROCEDURES
Keep bystanders, especially children and pets, at least
50 ft (15 m) away.
Wear safety glasses or goggles that are marked as
meeting ANSI Z87.1 standards, and ear/hearing
protection when operating this unit. Wear a face or
dust mask if the operation is dusty. Wear a hard hat.
Wear heavy, long pants, boots, gloves and a long sleeve
shirt. Do not wear loose clothing, jewelry, short pants,
sandals or go barefoot. Secure hair above shoulder level.
Use the unit only in daylight or good artificial light.
Use the right tool. Only use this tool for the purpose
intended.
Always stop the engine/motor when operation is
delayed or when walking fr
om one location to another.
Use only genuine factory replacement parts and
accessories for this unit. These are available from
your authorized service dealer. Use of any unauthorized
parts or accessories could lead to serious injury to the
user or damage to the unit, and void your warranty.
KICKBACK SAFETY PRECAUTIONS
With a basic understanding of kickback, you can
reduce or eliminate the element of surprise. Sudden
surprise contributes to accidents.
Grip saw firmly. Hold the pole saw firmly with both
hands when the motor is running. Keep a good firm grip
on the saw with both hands, the right hand on the r
ear
handle, and the left hand on the front handle.
Do not let the nose of the guide bar contact a log,
branch, gr
ound or other obstr
uction.
Always cut with the engine r
unning at full speed. Fully
squeeze the throttle trigger and maintain a steady
cutting speed.
RULES FOR SAFE OPERATION
Do not over reach.
Follow the manufacturer’s sharpening and
maintenance instructions for the saw chain.
Use only replacement bars and chains specified by the
manufacturer or the equivalent.
OTHER SAFETY PRECAUTIONS
DO NOT operate a pole saw with one hand! Serious
injury to the operator, helpers, or bystanders may
result from one-handed operation. A pole saw is
intended for two-handed use.
Do not operate a pole saw if you are fatigued.
Do not wear loose clothing or jewelry, as they can get
caught in moving parts. Non-skid footwear is
recommended when working outdoors. Wear
protective hair covering to contain long hair.
Use safety glasses, safety footwear, snug fitting
clothing, protective gloves, and protective hearing and
head gear.
Use caution when handling fuel. Move the pole saw at
lest 10 feet (3 m) from the fueling point before starting
the engine.
Do not allow other persons to be near the pole saw
when starting or cutting with the pole saw. Keep
bystanders and animals out of the work area.
Keep the work area clean. Cluttered areas invite
injuries. Do not start cutting until you have a clear
work area, secure footing, and a planned retreat path
from the falling branches.
Stay Alert. Watch what you are doing. Use common
sense. Do not operate the pole saw when you are
tired. Keep all parts of your body away from the saw
chain when the motor is operating. Before you start
the saw, make sure the saw chain is not contacting
anything.
Disconnect the pole saw when not in use, before
servicing, and when changing accessories and
attachments such as saw chain and guard.
Check damaged par
ts. Befor
e fur
ther use of the pole
saw, a guard or other part that is damaged should be
carefully checked to determine that it will operate
pr
operly and per
for
m its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may af
fect its operation. A guar
d or other par
t that
is damaged should be properly repaired or replaced by
an authorized service center, unless otherwise
indicated in this instr
uction manual.
Kickback may occur
when the nose or tip
of the guide bar touches an object, or when
the wood closes in and pinches the saw
chain in the cut. Tip contact in some cases
may cause a lightning-fast reverse action,
kicking the guide bar rapidly back towards
the operator. Pinching the saw chain along
the top of the guide bar may push the guide
bar rapidly back towards the operator.
Either of these reactions may cause you to
lose control of the saw, which could result in
serious injury to the user.
Do not rely exclusively upon the safety
devices built into your saw. As a pole saw
user, you should take several steps to keep
your cutting jobs fr
ee fr
om accident or injury.
WARNING:
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
5
Use extreme caution when cutting small sized brush
and sapling, as slender material may catch the saw
chain and be whipped towar
d you or pull you off
balance. Do not operate a pole saw in a tree unless
you are specifically trained to do so. When cutting a
limb that is under tension, be alert for spring back so
that you will not be struck when the tension in the
wood fibers is r
eleased. Do not expose the pole saw
to rain. Do not use the pole saw in damp or wet
locations. Do not use the pole saw in the presence of
flammable liquids or gases.
All pole saw service, other than the items listed in the
user manual safety and maintenance instructions,
should be performed by competent pole saw
personnel. Do not attempt to repair it yourself; there
are no user serviceable parts inside.
When not in use, pole saws should be stored out of
the r
each of children, in a dry, high or locked-up place.
When storing saw, use a scabbard or carrying case.
The pole saw will do a better and safer job when used
at the rate for which it was intended.
Use the right tool. Cut wood only. Do not use the pole
saw for purposes for which it was not intended. For
example, do not use the pole saw for cutting plastic,
masonry, or non-building materials.
Use devices, such as low-kickback chain, guide bar
nose guards and special guide bars, which reduce the
risks associated with kickback.
There are no other replacement components for
achieving kickback protection in accordance with CSA
Z62.3.
Do not operate a pole saw that is damaged,
improperly adjusted, or not completely and securely
assembled. Be sure that the saw chain stops moving
when the trigger is released.
Do not attempt operations beyond your capacity or
experience.
Never remove, modify or make inoperative any safety
device furnished with your unit.
This saw is classified by CSA as a Class 2C saw
. It is
intended for infrequent use by homeowner’s, cottagers
and campers, and for such general applications such
as clearing, pr
uning, cutting fir
ewood, etc. It is not
intended for prolonged use. If the intended use
involves pr
olonged periods of operation, this may
cause cir
culator
y pr
oblems in the user’s hands due to
vibration. It may be appropriate to use a saw having an
anti-vibration featur
e.
Safety clothing required by your safety organizations,
government regulations, or your employer should be
used; other
wise, snug fitting clothing, safety footwear,
and hand and ear protection should be worn.
Low-kickback saw chain is chain that has met the
kickback performance requirements of ANSI B175.1-
1991 and is in accordance with CSA Z62.3. Do not use
other replacement chain unless it has met these
requirements for your specific model.
Do not use any other cutting attachment or
accessories. Use only original equipment
manufacturer replacement parts and accessories,
which are designed specifically to enhance the
performance and maximize the safe operation of our
products. Failure to do so may cause poor
performance and possible injury. Use only the chain
and bar supplied with this pr
oduct. Do not use any
other cutting attachment. Use of such attachments will
void your factory warranty and could result in serious
bodily injury.
Never touch the chain or attempt to service the saw
while the engine is running. Make sure all moving parts
have stopped. Allow the pole saw to cool, as the chain
can be hot.
Check the bar and chain at frequent intervals for
proper adjustment. Make sure the bar and chain are
properly tightened and sharpened. Visually inspect for
damage. Repair any damage before restarting or
operating the pole saw.
Do not cut near electrical cables or power lines.
Do not use the chain saw to fell a tree. Use a standard
chain saw for this application.
MAINTENANCE AND STORAGE
Allow the unit to cool before storing or transporting.
Be sure to secure the unit while transporting.
Store the unit in a locked up and dry or high and dry
place to prevent unauthorized use or damage, out of
the r
each of childr
en.
Never douse or squir
t the unit with water or any other
liquid. Keep handles dry, clean and free from debris.
Clean after each use.
Keep these instructions. Refer to them often and use
them to instruct other users. If you loan someone this
unit, also loan them these instructions.
Only qualified personnel should perform any repairs
or maintenance procedures that are not described
in this manual.
SAVE THESE
INSTRUCTIONS
RULES FOR SAFE OPERATION
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
6
RULES FOR SAFE OPERATION
SYMBOL
MEANING
SAFETY ALERT SYMBOL
Indicates danger, warning, or cau-
tion. May be used in conjunction
with other symbols or pictographs.
WARNING - READ OPERATOR'S
MANUAL
Read the Operator’s Manual(s) and
follow all warnings and safety
instructions. Failure to do so can
result in serious injury to the opera-
tor and/or bystanders.
WEAR HEAD, EYE AND HEARING
PROTECTION
WARNING: Thrown objects and
loud noise can cause severe eye
injury and hearing loss. Wear eye
protection meeting ANSI Z87.1-
1989 standards and ear protection
when operating this unit. Falling
objects can cause severe head
injury. Wear head protection when
operating this unit.
Use a full face
shield when needed.
KEEP BYSTANDERS AWAY
WARNING: Keep all bystanders,
especially childr
en and pets, at least
50 feet (15 m) from the operating
area.
SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes safety and inter
national symbols and pictographs that may appear on this product.
Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.
SYMBOL
MEANING
THROWN OBJECTS CAN CAUSE
SEVERE INJURY
WARNING:
Do not operate unit
without proper attachments and
guards in place.
GUIDE BAR WARNING
Contact of the guide bar tip with any
object should be avoided. Tip contact
may cause the guide bar to move
suddenly upward and backward,
which may cause serious injury.
USE BOTH HANDS
Always use both hands while oper-
ating the chain saw. Never use only
one hand to operate the saw.
HOT SURFACE WARNING
Do not touch a hot muffler or cylin-
der. You may get burned. These
par
ts get extr
emely hot from opera-
tion. When turned off they remain
hot for a short time.
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
7
RULES FOR SAFE OPERATION
KNOW YOUR UNIT
Tension
Adjustment Screw
Guide Bar
Saw Chain
Oil Tank Cap
Drive Shaft
Guide Bar
Nose
Sprocket
Cover
Foot
Bar Retaining Nuts
Extension Pole
Coupler
Knob
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
8
OPERATING INSTRUCTIONS
The add-on should be installed with the release button in
the primary hole.
Check Flex Shaft Engagement Prior to Using
1. Start the unit.
2. Briefly engage and release the trigger.
3. Check that add-on is operating.
4.
If the add-on is not operating, r
emove add-on and
repeat steps for installing the add-on.
5. Recheck operation of add-on attachment.
4. Turn the knob clockwise to tighten (Fig. 3).
ASSEMBLING THE COUPLER
The following TrimmerPlus Add-Ons are also available for your
unit:
Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .GC720r
Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .LE720r
Hedge T
rimmer . . . . . . . . . . . . . . . . . . . . . . . . . . HS720r
Straight Shaft T
rimmer . . . . . . . . . . . . . . . . . . . . SS725r
Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . TB720r
Pole Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBPS
NOTE: To make installing or removing the add-on easier,
place the unit on the ground or on a work bench.
NOTE: The extension pole with this unit is to give the
user added reach. Follow the directions for
removing the add-on or installing the add on to
remove or install the extension pole.
Removing the add-on
1. Turn the knob counterclockwise to loosen (Fig. 1).
2. Press and hold the release button (Fig. 1).
3. While firmly holding the upper shaft housing, pull the
add-on out of the coupler (Fig. 2).
Installing the add-on
1.
Remove the hanger fr
om the top of the shaft housing.
2. Turn knob counterclockwise to loosen (Fig. 1).
3. While firmly holding the add-on, push it straight into
the coupler (Fig. 2).
Fig. 1
Coupler
Release Button
Guide Recess
Knob
Primary Hole
Upper Shaft
Housing
Coupler
NOTE: Aligning the r
elease button with the guide recess
will help installation (Fig. 1).
Fig. 2
Fig. 3
Knob
Lower Shaft
Housing
Release Button
Knob
Clockwise
Counter
clockwise
Prior to operation,
read and understand
the operator’s manual for unit to be used with
this add-on.
WARNING:
To avoid serious
personal injury and
damage to the unit, shut the unit off befor
e
removing or installing add-ons.
WARNING:
The add-ons with the
coupler system is to
be used in the primary hole only. Using the
wrong hole could lead to personal injury or
damage to the unit.
CAUTION:
Lock the release
button in the primary
hole (Fig. 2) and securely tighten the knob
before operating this unit.
CAUTION:
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
9
OPERATING INSTRUCTIONS
Fig. 4
Fig. 5
Fig. 6
OPERATING PRECAUTIONS
1. Keep bystanders 50 feet (15 meters) away when
operating the saw.
2. Do not use the pole saw to cut down trees. Use a
chain saw without a pole attachment.
3. Grip pole saw securely - one hand on the pole, the
other on the handle.
4. Keep finger off the trigger until ready to make cut.
5. Before starting the pole saw, make sure the chain is
not touching anything.
6. Keep all parts of your body away from the chain
when the saw is running.
7. Do not force the pole saw while cutting. Apply light
pressure. It will do the job better and safer at the rate
for which it was intended.
8. When cutting limbs or branches that are under
tension, use extreme caution. Be alert for wood
springing back. When wood tension is released, the
limb could spring back and strike operator causing
severe injury or death.
9. When carrying pole saw from one place to another:
• hold pole at balance point
• keep guide bar and chain to the rear
10. Do not cut small brush and saplings with the pole
saw. Use a chain saw only, with extreme care.
Slender matter may catch in the chain and be
whipped towar
d you. This could also pull you of
f
balance.
11. Never stand directly under the limb you are trimming.
Always position yourself out of the path of falling
debris (Fig. 4).
12. Never stand on a ladder or other type of unstable
suppor
t while using the pole saw
.
13. Always use both hands to operate pole saw. Keep a
firm, steady pressure on the pole saw while cutting,
but do not tr
y to for
ce the saw through the wood.
14.
Do not use the pole saw to cut limbs larger than
4” (10 cm) in diameter.
15. Keep other persons away from cutting end of pole
saw and at a safe distance from work area. (Fig.5).
16.
Do not use the pole saw near cable, electric power
or telephone lines. Maintain a minimum clearance of
10 feet from all power lines (Fig. 6).
Dr
ess properly to
r
educe the risk of
injur
y when operating this unit. Do not
wear loose clothing or jewelr
y. Wear eye
and ear/hearing pr
otection. Wear heavy
long pants, boots and gloves. Wear a hard
hat. Use a full face shield when needed.
WARNING:
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
10
OPERATING INSTRUCTIONS
OPERATING TIPS
A
void kickback. Kickback can result in severe injury or
death.
Do not operate the pole saw while in a tree, on a ladder
or any other unstable work surface, or in any awkward
position. You may lose control of the pole saw causing
severe injury.
Do not extend your arms above shoulders when using
the pole saw. Seek professional help if you are facing
conditions beyond your ability.
Trimming a tree is the process of cutting limbs from a
living tree. Make sure your footing is firm. Keep your feet
apart. Divide your weight evenly on both feet.
Avoid kickback.
Kickback can result
in sever in jur
y or death. See Kickback,
page 9, to avoid risk of kickback.
WARNING:
1. When operating the pole saw, rest the foot (A) of the
pole saw against the tree limb that is being cut. (Fig.
7)
2. Make the frist cut one (1) foot from where the final
cut will be. (Fig. 8)
3. Cut the outside of the branch collar to avoid damage
to the tree. (Fig. 9)
Do not operate Pole
Saw while in a tree,
on a ladder or any other unstable work
surface, or in any awkward position. You
may lose control of Pole Saw causing
servere injury.
WARNING:
Do not extend arms
above shoulders
when using Pole Saw
.
WARNING:
Seek professional
help if facing
conditions beyond your ability.
WARNING:
Fig. 7
A
Fig. 8
1 Foot
Fig. 9
Cut
Collar
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
11
MAINTENANCE AND REPAIR INSTRUCTIONS
SAW CHAIN REPLACEMENT/INSTALLATION
1. Remove the bar retaining nuts and screw. Then take
off the sprocket cover (Fig. 10a).
2. Using a straight screwdriver turn tension adjustment
screw counterclockwise (Fig. 10b) as far as it will go
or to the end of its travel, take off the chain then
remove the bar.
Whenever handling
the saw chain,
always wear work gloves for protection
against sharp cutting edges.
WARNING:
Fig. 10
A
B
Bar Retaining
Nuts
Spr
ocket
Cover
Screw
Tension
Adjustment
Screw
Fig. 10
3. Prepare new chain or bar.
4. Loop the saw chain over the drive sprocket with the
cutting edges of the chain pointing in the direction of
rotation (Fig. 11).
5. Adjust the tension adjustment screw (Fig. 10b) to
allow insertion of the bar (Fig. 12). Make sure the
chain follows the slot in the guide bar and adjust the
tension adjustment screw to make the chain tighten.
6. Install the sprocket cover and tighten bar retaining
nuts and screw (Fig. 10a).
Fig. 11
Fig. 13
SAW CHAIN TENSION ADJUSTMENT
Pr
oper tension of the saw chain is extremely important
and must be checked before starting, as well as during,
any cutting operation. Taking the time to make needed
adjustments to the saw chain will result in improved
cutting performance and prolonged chain life.
NOTE: A new chain and bar will need r
eadjustment after
as few as 5 cuts. This is normal during the
break-in period, and the interval between future
adjustments will lengthen quickly (Fig. 13).
If a chain is too loose
or too tight, the bar,
chain and saw bearings will wear more
rapidly. Refer to Figure 14 for information
concerning correct cold tension (A), correct
war
m tension (B), and a chain in need of
adjustment (C).
CAUTION:
A
C
B
To adjust the saw chain tension:
1. Loosen the bar retaining nuts so they are hand tight
(Fig. 8a).
2. Holding the nose of the bar up, use the screwdriver or
scr
ench (if pr
ovided in your unit’
s har
dwar
e pack) to
turn the guide bar adjustment screw clockwise to
tighten the chain (Fig. 8b). Turning the screw
counterclockwise loosens the chain on the guide bar.
3.
While wearing heavy duty work gloves (after you’ve
made the adjustment), move the saw chain back and
forth on the guide bar to be sure the chain moves
fr
eely and is in pr
oper mesh with the sprocket. Never
move the chain with your bare hands.
NOTE: IF the chain is difficult to rotate or if it binds on
the guide bar
, ther
e is too much tension applied
and it must be adjusted. T
o decr
ease tension,
turn the adjustment screw counterclockwise,
slowly
. Move the chain back and for
th until it
moves fr
eely
.
4.
Holding the nose in upper position, secur
ely tighten
the bar retaining nuts.
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
12
OILING THE CHAIN
The pole saw chain is self-lubricating. Oil is dispersed
onto the chain as the unit is used. Keep an adequate
amount of oil in the oil tank. Use the bar-chain oil
provided in the hardware pack. Always use bar-chain
and sprocket oil or similar chain saw oil.
GUIDE BAR MAINTENANCE
NOTE: Proper maintenance of the guide bar is essential
to the performance of your pole saw. Proper
guide bar maintenance will keep your saw in
good working order.
Most guide bar problems can be prevented merely by
keeping the chain saw well maintained.
Incorrect filing and non-uniform cutter and depth gauge
settings cause most guide bar problems, primarily
resulting in uneven bar wear. As the bar wears unevenly,
the rails widen, which may cause chain clatter and
difficulty in making straight cuts.
Insufficient guide bar lubrication and operating the saw
with a chain that is
too tight will contribute to rapid bar
wear. Refer to Saw Chain Tension Adjustment.
To help minimize bar wear, the following guide bar
maintenance is recommended:
Bar Wear
Turn guide bar frequently at regular intervals (for
example, after 5 hours of use), to ensure even wear on
top and bottom of bar.
Ensur
e that the unit
is off and the spark
plug is disconnected (gas powerheads) before
performing any maintenance on your saw.
WARNING:
Bar Grooves
Bar grooves (or rails which support and carry the chain)
should be cleaned if the saw has been heavily used or if
the saw chain appears dirty. Rails should always be
cleaned every time the saw chain is removed.
T
o clean guide bar rails:
1. Remove sprocket cover, bar and chain. Refer to Saw
Chain Replacement / Installation
.
2. Using a screwdriver, putty knife, wire brush or other
similar instrument, clear residue from the rails on the
guide bar (Fig. 14).
This will keep the oil passages open to provide
proper lubrication to the bar and chain.
3. Reinstall the bar, chain and bar bolt retaining nuts.
Refer to
Saw Chain Replacement / Installation.
MAINTENANCE AND REPAIR INSTRUCTIONS
Fig. 14
Oil Passages
Oil passages at bar pad should be cleaned to insure
proper lubrication of the bar and chain during operation.
This can be done using a soft wire small enough to insert
into the oil discharge hole.
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
13
MAINTENANCE AND REPAIR INSTRUCTIONS
CHAIN MAINTENANCE
A low-kickback saw chain should always be used in
conjunction with other kickback protection devices such
as the hand guard, which is furnished with your unit.
Always use a r
eplacement saw chain designed as “low-
kickback” or a saw chain which meets the low-kickback
per
formance.
A standard saw chain (a chain which does not have the
kickback reducing guard links) should only be used by
an experienced professional chain saw operator.
Low-Kickback Saw Chain
A low-kickback saw chain is a chain which has met the
kickback performance requirements of ANSI B175.1. Do
not use other replacement chain unless it has met these
requirements for your specific model.
By keeping the saw chain in good working condition and
correctly serviced as recommended in this manual, you
will be able to maintain the safety system of your chain
saw over the life of the product.
Ensure that the unit
is off and the spark
plug is disconnected (for gas powerheads)
when working on the saw chain. Wear heavy
duty gloves too.
WARNING:
Never remove,
modify or make
inoperative any safety device furnished with
your unit. The low kick back saw chain is a
major safety feature provided for your
protection.
WARNING:
Unless you have
experience and
specialized training for dealing with
kickback (see Important Safety Instructions),
always use a low-kickback saw chain,
which significantly reduces the danger of
kickback. Low-kickback saw chain does not
completely eliminate kickback. A low-
kickback or “safety chain,” should never be
regarded as total protection against injury.
WARNING:
Chain Tension
Check the chain tension frequently and adjust as often
as necessary to keep the chain snug on the bar, but
loose enough to be pulled around by hand. Refer to
Saw
Chain Tension Adjustment.
Br
eaking in a New Saw Chain
A new chain and bar will need readjustment after as few
as 5 cuts. This is normal during the break-in period, and
the interval between future adjustments will begin to
lengthen quickly.
Over a period of time, however, the moving parts of the
saw chain will become worn, resulting in what is called
chain stretch. This is normal. When it is no longer
possible to obtain correct chain tension adjustment, a
link will have to be removed to shorten the chain. See
your TrimmerPlus Authorized Service Center to have this
repair performed.
Never use a loop of
chain that has more
than 3 links removed from it. This could
damage the sprocket.
WARNING:
SPECIFICATIONS
POLE SAW ADD-ON
Approximate Operating Weight of Attachment........................................................................................... 3.3 lbs. (1.5 kg)
Drive Shaft Length.............................................................................................................................................. 26” (66 cm)
Cutting Width................................................................................................................................................... 8" (200 mm)
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
MANUFACTURER’S LIMITED WARRANTY FOR:
No implied warranty
, including any implied warranty of
merchantability or fitness for a particular purpose,
applies after the applicable period of express written
warranty above as to the parts as identified. No other
express warranty or guaranty, whether written or oral,
except as mentioned above, given by any person or
entity, including a dealer or retailer, with respect to any
product shall bind TrimmerPlus During the period of the
Warranty, the exclusive remedy is repair or replacement
of the product as set forth above.
(Some states do not
allow limitations on how long an implied warranty lasts, so
the above limitation may not apply to you.)
The provisions as set forth in this Warranty provide the
sole and exclusive r
emedy arising from the sales.
TrimmerPlus shall not be liable for incidental or conse-
quential loss or damages including, without limitation,
expenses incurr
ed for substitute or replacement lawn
care services, for transportation or for related expens-
es, or for rental expenses to temporarily replace a war-
ranted product.
(Some states do not allow limitations on
how long an implied warranty lasts, so the above limitation
may not apply to you.)
In no event shall recovery of any kind be greater than the
amount of the purchase price of the product sold. Alteration
of the safety features of the product shall void this Warranty.
You assume the risk and liability for loss, damage, or injury
to you and your property and/or to others and their proper-
ty arising out of the use or misuse or inability to use the
product.
This limited warranty shall not extend to anyone other than
the original pur
chaser, original lessee or the person for
whom it was purchased as a gift.
How State Law Relates to this Warranty: This warranty
gives you specific legal rights, and you may also have other
rights which vary from state to state.
To locate your nearest service dealer dial
1-800-345-8746.
MTD Southwest Inc
PO Box 361131
Cleveland, OH 44136-0019
The limited war
ranty set forth below is given by TrimmerPlus
with respect to new merchandise purchased and used in
the United States, its possessions and territories.
TrimmerPlus warrants this product against defects in mate-
rial and workmanship for a period of two (2) years com-
mencing on the date of original purchase and will, at its
option, repair or replace, free of charge, any part found to be
defective in material or workmanship. This limited warranty
shall only apply if this product has been operated and main-
tained in accordance with the Operator’s Manual furnished
with the product, and has not been subject to misuse,
abuse, commercial use, neglect, accident, improper main-
tenance, alteration, vandalism, theft, fire, water or damage
because of other peril or natural disaster. Damage resulting
fr
om the installation or use of any accessory or attachment
not approved by TrimmerPlus for use with the product(s)
covered by this manual will void your warranty as to any
resulting damage. This warranty is limited to ninety (90) days
from the date of original retail purchase for any TrimmerPlus
product that is used for rental or commercial purposes, or
any other income-producing purpose.
HOW TO OBTAIN SERVICE: Warranty service is available,
WITH PROOF OF PURCHASE THROUGH YOUR LOCAL
AUTHORIZED SERVICE DEALER. To locate
the dealer in
your area, visit our website at www.TrimmerPlus.com,
check
for a listing in the Yellow Pages, call 1-800-345-8746 or
write to
P.O. Box 361131, Cleveland, OH 44136-0019
.
This limited warranty does not provide coverage in
the following cases:
A. Tune-ups - Spark Plugs, Carburetor Adjustments,
Filters
B.
W
ear items - Bump Knobs, Outer Spools, Cutting
Line, Inner Reels, Star
ter Pulley, Starter Ropes, Drive
Belts
C. TrimmerPlus does not extend any warranty for prod-
ucts sold or exported outside of the United States of
America, its possessions and ter
ritories, except
those sold through TrimmerPlus’s authorized chan-
nels of export distribution.
T
rimmerPlus
reserves the right to change or improve the
design of any TrimmerPlus Product without assuming any
obligation to modify any pr
oduct pr
eviously manufactur
ed.
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
Sie de Pole
PS720r
Manuel de L'utilisateur
IMPORTANT: LISEZ LES RÈGLES ET
CONSIGNES DE SÉCURITÉ SOIGNEUSEMENT
P/N 9096-A10708
© 2005
F
ABRIQUÉ Á T
AIW
AN
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
F7
CONSIGNES DE SÉCURITÉ
FAMILIARISEZ-VOUS AVEC VOTRE APPAREIL
Vis de réglage
de tension
Guide-chaîne
Chaîne
Bouchon du
réservoir a huile
Tarbre de
Transmission
Tête du
guide-chaîne
Couvercle
du pignon
Pied
Ecrous du guide-chaîne
Prolongation Polonais
Coupler
Coupleur
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
Cortadora de
Poste
PS720r
Manual Del Operador
IMPORTANTE: LEA LAS REGLAS DE SEGURIDAD E
INSTRUCCIONES DETENIDAMENTE
P/N 9096-A10708
© 2005
HECHO EN T
AIW
AN
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
E7
NORMAS PARA UNA OPERACIÓN SEGURA
Tornillo para
ajuste de tension
Guia de barra
Cadena
para contar
Tapon de tanque
aceite
Ensamble de
eje impulsor
Punta de guia
de barra
Cubierta del
engrane
Pie
Tuerca sujeta dora de barra
CONOZCA SU UNIDAD
Extensión Poste
Acoplador
Botón
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
E14
NOTAS
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
E15
PARTS LIST
REPLACEMENT PARTS - MODEL PS720r
POLE SAW ADD-ON
Item Part No. Description
1 753-04621 Gearbox
2 753-04622 Screw
3 753-04623 Shaft Assembly
4 753-04624 Spindle Assembly
5 753-04625 Connection Stick Assembly
6 753-04626 Screw
7 753-04627 Case Cover
8 753-04628 Screw
9 753-04629 Sprocket
10 753-04630 Washer
11
753-04631
C Ring
12 753-04632 Oil Pump Assembly
13
753-04633
Rubber Cork
14 753-04634 Fixed Plate
15
753-04635
Scr
ew
Item
Part No. Description
16 753-04636 Oiler Assembly
17 753-04637 Anti-Spillage Pad
18 753-04638 Regulation Screw
19 753-04639 Regulation Cap
20 753-04640 Adjustable Plate
21
753-04641 Screw
22 753-04642 Bar 8”
23
753-04643 Saw Chain
24 753-04644 Guard
25
753-04644 Fixed Ring
26 753-04645 Nut
27
753-04646 Screw
28 753-04647 Covering
29
753-04649 Guard
30 753-04648 Inner Pipe Assembly
1
2
5
28
30
6
8
7
13
14
15
29
25
26
27
24
23
22
21
20
18
19
17
11
10
9
6
3
4
16
12
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
For Parts Call 606-678-9623 or 606-561-4983
www.mymowerparts.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

MTD PS720r User manual

Category
Power chainsaws
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages