Milwaukee 6519 Series User manual

Page is loading ...

page 2

GENERAL SAFETY RULES  FOR ALL POWER TOOLS

WORK AREA SAFETY

ELECTRICAL SAFETY

PERSONAL SAFETY

POWER TOOL USE AND CARE

SERVICE

4. Power tool plugs must match the outlet. Never modify the

plug in any way. Do not use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs and matching outlets

will reduce risk of electric shock.

5. Avoid body contact with earthed or grounded surfaces such

as pipes, radiators, ranges and refrigerators. There is an

increased risk of electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet conditions. Water

entering a power tool will increase the risk of electric shock.

7. Do not abuse the cord. Never use the cord for carrying,

pulling, or unplugging the power tool. Keep cord away from

heat, oil, sharp edges, or moving parts. Damaged or entangled

cords increase the risk of electric shock.

8. When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for outdoor

use reduces the risk of electric shock.

WARNING!

READ ALL INSTRUCTIONS

Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in

all of the warnings listed below refers to your mains-operated (corded) power tool or battery-opearted (cordless) power tool.

SAVE THESE INSTRUCTIONS

16. Do not force the power tool. Use the correct power tool for

your application. The correct power tool will do the job better and

safer at the rate for which it was designed.

17. Do not use the power tool if the switch does not turn it on

and off. Any power tool that cannot be controlled with the switch is

dangerous and must be repaired.

18. Disconnect the plug from the power source and/or the bat-

tery pack from the power tool before making any adjust-

ments, changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the tool acci-

dentally.

19. Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tools or these

instructions to operate power tools. Power tools are danger-

ous in the hands of untrained users.

20. Maintain power tools. Check for misalignment or binding of

moving parts, breakage of parts and any other condition

that may affect the power tool's operation. If damaged, have

the power tool repaired before use. Many accidents are caused

by poorly maintained power tools.

21. Keep cutting tools sharp and clean. Properly maintained cutting

tools with sharp cutting edges are less likely to bind and are easier

to control.

22. Use the power tool, accessories and tool bits etc., in accor-

dance with these instructions and in the manner intended

for the particular type of power tool, taking into account the

working conditions and the work to be performed. Use of

the power tool for operations different from those intended could

result in a hazardous situation.

23. Have your power tool serviced by a qualified repair person

using only identical replacement parts. This will ensure that

the safety of the power tool is maintained.

1. Keep work area clean and well lit. Cluttered or dark areas invite

accidents.

2. Do not operate power tools in explosive atmospheres, such

as in the presence of flammable liquids, gases, or dust.

Power tools create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while operating a power

tool. Distractions can cause you to lose control.

9. Stay alert, watch what you are doing and use common sense

when operating a power tool. Do not use a power tool while

you are tired or under the influence of drugs, alcohol or

medication. A moment of inattention while operating power tools

may result in serious personal injury.

10. Use safety equipment. Always wear eye protection. Safety

equipment such as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions will reduce per-

sonal injuries.

11. Avoid accidental starting. Ensure the switch is in the off-

position before plugging in. Carrying tools with your finger on

the switch or plugging in power tools that have the switch on invites

accidents.

12. Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

13. Do not overreach. Keep proper footing and balance at all

times. This enables better control of the power tool in unexpected

situations.

14. Dress properly. Do not wear loose clothing or jewellery.

Keep your hair, clothing and gloves away from moving parts.

Loose clothes, jewellery, or long hair can be caught in moving parts.

15. If devices are provided for the connection of dust extrac-

tion and collection facilities, ensure these are connected

and properly used. Use of these devices can reduce dust-re-

lated hazards.

page 3

1. Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden

wiring or its own cord. Contact with a live wire will make exposed metal parts of the tool live and shock the operator.

2. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against

your body leaves it unstable and may lead to loss of control.

3. Keep hands away from all cutting edges and moving parts.

4. Maintain labels and nameplates. These carry important information. If unreadable or missing, contact a MILWAUKEE service facility for a free

replacement.

5. WARNING! Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause

cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

 lead from lead-based paint

 crystalline silica from bricks and cement and other masonry products, and

 arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in

a well ventilated area, and work with approved safety equipment, such as those dust masks that are specifically designed to filter out microscopic

particles.

Amperes

Double Insulated

Symbology

Canadian Standards

Association

Underwriters

Laboratories, Inc.

Volts Alternating Current

No Load Strokes

per Minute (RPM)

RPM

0 - 2 800

Volts

AC

120

Cat.

No.

6509 Series

6519 Series

Specifications

Amps

10

Length of

Stroke

3/4"

1-1/8"

SPECIFIC SAFETY RULES

FUNCTIONAL DESCRIPTION

1. Handle

2. Trigger

3. Quik-Lok

®

blade clamp

4. Blade

5. Adjustable pivot shoe

6. Shoe release lever

7. Pivot shoe access holes

8. Insulating boot

9. Quik-Lok

®

cord

10. Fixed cord

6509 Series

2

1

3

5

7

4

8

10

6519 Series

1

3

2

4

6

5

9

8

page 4

Grounded tools require a three wire extension cord. Double insulated

tools can use either a two or three wire extension cord. As the distance

from the supply outlet increases, you must use a heavier gauge exten-

sion cord. Using extension cords with inadequately sized wire causes a

serious drop in voltage, resulting in loss of power and possible tool

damage. Refer to the table shown to determine the required minimum

wire size.

The smaller the gauge number of the wire, the greater the capacity of the

cord. For example, a 14 gauge cord can carry a higher current than a 16

gauge cord. When using more than one extension cord to make up the

total length, be sure each cord contains at least the minimum wire size

required. If you are using one extension cord for more than one tool, add

the nameplate amperes and use the sum to determine the required mini-

mum wire size.

Guidelines for Using Extension Cords

 If you are using an extension cord outdoors, be sure it is marked

with the suffix W-A (W in Canada) to indicate that it is acceptable

for outdoor use.

 Be sure your extension cord is properly wired and in good electrical

condition. Always replace a damaged extension cord or have it

repaired by a qualified person before using it.

 Protect your extension cords from sharp objects, excessive heat

and damp or wet areas.

EXTENSION CORDS

Nameplate

Amperes

0 - 5

5.1 - 8

8.1 - 12

12.1 - 15

15.1 - 20

Extension Cord Length

25'

16

14

12

10

75'

16

14

12

10

100'

14

12

10

--

150'

12

10

--

200'

12

--

Recommended Minimum Wire Gauge

for Extension Cords*

* Based on limiting the line voltage drop to five

volts at 150% of the rated amperes.

50'

16

14

12

10

READ AND SAVE ALL INSTRUCTIONS

FOR FUTURE USE.

GROUNDING

Grounded Tools:

Tools with Three Prong Plugs

Tools marked Grounding Required

have a three wire cord and three

prong grounding plug. The plug must

be connected to a properly grounded

outlet (See Figure A). If the tool should

electrically malfunction or break

down, grounding provides a low re-

sistance path to carry electricity

away from the user, reducing the risk

of electric shock.

Improperly connecting the grounding wire can result in the

risk of electric shock. Check with a qualified electrician if you

are in doubt as to whether the outlet is properly grounded.

Do not modify the plug provided with the tool. Never remove

the grounding prong from the plug. Do not use the tool if the

cord or plug is damaged. If damaged, have it repaired by a

MILWAUKEE service facility before use. If the plug will not fit

the outlet, have a proper outlet installed by a qualified

electrician.

The grounding prong in the plug is connected through the green wire

inside the cord to the grounding system in the tool. The green wire in the

cord must be the only wire connected to the tool's grounding system and

must never be attached to an electrically live terminal.

Your tool must be plugged into an appropriate outlet, properly installed

and grounded in accordance with all codes and ordinances. The plug

and outlet should look like those in Figure A.

Double Insulated Tools:

Tools with Two Prong Plugs

Tools marked Double Insulated do

not require grounding. They have a

special double insulation system

which satisfies OSHA requirements

and complies with the applicable

standards of Underwriters Labora-

tories, Inc., the Canadian Standard

Association and the National Electri-

cal Code. Double Insulated tools may

be used in either of the 120 volt out-

lets shown in Figures B and C.

WARNING!

Fig. A

Fig. B

Fig. C

page 5

Removing and Replacing Quik-Lok

®

Cords (Fig. 1)

(Select Models)

MILWAUKEE's exclusive Quik-Lok

®

Cords provide instant field replace-

ment or substitution.

Fig. 1

1. To remove the Quik-Lok

®

Cord, turn the cord nut 1/4 turn to the left

and pull it out.

2. To replace the Quik-Lok

®

Cord, align the connector keyways and

push the connector in as far as it will go. Turn the cord nut 1/4 turn

to the right to lock.

Selecting a Blade

Use MILWAUKEE Sawzall

®

Blades for best performance. When select-

ing a blade, choose the right type and length.

Many types of blades are available for a variety of applications: cutting

metal, wood, nail-embedded wood, scroll cutting, roughing-in, and

contours.

Many lengths are also available. Choose a length long enough to extend

beyond the shoe and your work throughout the stroke. For best perfor-

mance and longest life, see "Accessories" to select the best blade for

the job.

1. Unplug the tool before changing blades.

2. Be sure the spindle and blade clamp area are clean. Metal chips and

sawdust may prevent the blade clamp screw from clamping se-

curely.

3. To install a blade, loosen the blade clamp screw, turning it counter-

clockwise. Insert the blade until the tang butts against the spindle.

NOTE: The blade must be inserted all the way into the spindle so that

the tang on the blade seats firmly in the blade clamp.

Depending on the job, the blade may be inserted with the teeth

facing upward or downward.

4. Insert the hex key into the blade clamp screw, turning it clockwise.

Tighten securely.

5. To remove a blade, insert hex key into the blade clamp screw and

turn it counterclockwise 1 full turn. Then slide the blade out of the

spindle. Be careful when handling hot blades.

Blade

Collar

Fig. 2

Quik-Lok

®

Blade Clamp (Fig. 2) (Select Models)

1. Unplug the tool.

2. Be sure the spindle and blade clamp areas are clean. Metal chips

and sawdust may prevent the Quik-Lok

®

Blade Clamp from clamping

securely (see "Maintenance").

3. To install a blade, twist the collar in the direction of the arrow while

inserting the blade into the clamp until the tang butts against the

collar.

Depending on the job, the blade may be inserted with the teeth

facing upward or downward.

4. Release the collar and the spring loaded mechanism will clamp the

blade firmly in place.

5. Twist the collar in the opposite direction of the arrow to ensure that

the blade is locked into the clamp.

6. Tug on blade to make sure it is securely locked in place.

7. To remove a blade, twist the collar in the direction of the arrow

while pulling on the blade. Be careful when handling hot blades.

Fig. 3

Blade clamp screw

Hex key

Installing and Removing Blades

Blade Clamp (Available as accessory Cat. No. 49-22-5016 only)

(Fig. 3)

Removing Broken Blades from the Quik-Lok

®

Blade Clamp

1. Unplug the tool.

2. Broken blades can be removed by the following methods.

 Point the tool downward, twist the collar, and shake the tool up and

down (DO NOT turn on the tool while your fingers are holding the

blade clamp open). The shank of the broken blade should drop out of

the clamp.

 If shaking the tool doesn't work...

In most cases, a corner of the broken blade will extend beyond the

blade clamp. Twist the collar and pull the broken blade out of the

clamp by this corner.

 If the broken stub doesn't extend far enough to be grabbed by its

corner, use a thin blade with small teeth (such as a metal cutting

blade) to hook the blade that is jammed in the clamp while twisting

the collar and pull it out.

WARNING!

TOOL ASSEMBLY

To reduce the risk of injury, always unplug tool before

attaching or removing accessories or making adjustments.

Use only specifically recommended accessories. Others

may be hazardous.

page 6

Adjustable Pivot Shoe

The shoe can be adjusted forward or backward to take advantage of the

unused portion of the blade or for special jobs requiring low blade

clearance.

6509 Series (Fig. 4)

Stroke

Fig. 6

WARNING!

To reduce the risk of injury, be sure the blade always

extends beyond the shoe and work throughout the stroke.

Blades may shatter if they impact the work or shoe (Fig. 6).

WARNING!

Do not operate Sawzall without a shoe. Striking the spindle

against the work may damage the reciprocating mechanism.

1. To adjust the shoe, place hex wrench through access holes in

insulating boot and loosen four (4) screws.

2. Move shoe to desired position

3. Tighten screws.

4. After adjusting the shoe, slowly pull the trigger to be sure the blade

always extends beyond the shoe and your work throughout the

stroke.

6519 Series (Fig. 5)

Fig. 4

Adjusting

screws

Hex wrench

Insulating

boot

Access holes

1. To adjust the shoe, pull out the shoe release lever 1/4 turn.

2. Slide the shoe forward or backward to the desired position.

3. To lock the shoe in position, push in the shoe release lever.

4. After adjusting the shoe, slowly pull the trigger to be sure the blade

always extends beyond the shoe and your work throughout the

stroke.

Fig. 5

Shoe release lever

page 7

Impact Protection System (Select Models)

Select models are equipped with a unique patented gearing system that

provides efficient power transmission and extended life in the most

difficult cutting applications. This durable system will absorb impacts,

blade lock ups, and motor stalls. These models can be used for extreme

cutting applications such as large diameter pipe, thick metal, pallets, and

heavy demolition and renovation work as well as for general purpose

cutting.

Starting, Stopping and Controlling Speed

1. To start the tool, grasp the handle firmly and pull the trigger.

2. To stop the tool, release the trigger. Allow the tool to come to a

complete stop before removing the blade from a partial cut or laying

the tool down.

Trigger Speed Control Switch

MILWAUKEE Sawzalls

®

are equipped with a trigger speed control switch.

It may be operated at any speed from zero strokes per minute to full

speed. Always start tool before blade contacts the workpiece. To vary

the speed, simply increase or decrease the pressure on the trigger. The

further the trigger is pulled, the greater the speed. To stop the tool,

release the trigger and allow the tool to stop completely before removing

from a partial cut or before laying the tool down.

General Cutting

For straight or contour cutting from an edge, line the blade up with your

cutting line. Before the blade contacts the workpiece, grasp the handle

firmly and pull the trigger. Then guide the tool along your cutting line.

Always hold the shoe flat against the workpiece to avoid excessive

vibration.

Cutting Metals

Begin cutting at a slow speed, gradually increasing speed as you cut.

When cutting into metals or hard materials that can not be cut from an

edge, drill a starting hole larger than the widest part of the blade. Extend

blade life by using a solid blade cutting lubricant such as MILWAUKEE

Band Saw Blade Lubricant Cat. No. 49-08-4206.

Plunge Cutting (Fig. 7)

Your MILWAUKEE Sawzall

®

is ideal for plunge cutting directly into sur-

faces that can not be cut from an edge, such as walls or floors. Plunge

cutting may be done two ways depending on how the blade is inserted.

Column A shows how to plunge cut with the teeth of the blade facing

down. Column B shows how to plunge cut with the teeth of the blade

facing up. Do not plunge cut into metal surfaces (see Cutting Metals).

1. Insert the blade into the tool.

If you inserted the blade with the teeth facing downward, hold the

tool as shown in Column A, resting the edge of the shoe on the

workpiece.

If you inserted the blade with the teeth facing upward, hold the tool

as shown in Column B, resting the edge of the shoe on the work-

piece as shown.

2. With the blade just above the workpiece, pull the trigger. Using the

edge of the shoe as a pivot, lower the blade into the workpiece as

shown.

3. As the blade starts cutting, raise the handle of the tool slowly until

the shoe rests firmly on the workpiece. Then guide the tool along

your cutting line to acquire the desired cut.

NOTE: To make plunge cutting easier, use a heavy gauge blade and

install the blade with the teeth facing upward as shown in Column B.

WARNING!

To reduce the risk of explosion, electric shock and property

damage, always check the work area for hidden gas pipes,

electrical wires or water pipes when making blind or plunge

cuts.

Fig. 7

OPERATION

WARNING!

To reduce the risk of injury, wear safety goggles or glasses

with side shields. Unplug the tool before changing accesso-

ries or making adjustments.

page 8

Quik-Lok

®

Blade Clamp Maintenance

 Periodically clean dust and debris from the Quik-Lok

®

Blade Clamp

with dry compressed air.

 If the collar resists twisting, twist the collar back and forth to shake

debris loose.

 Periodically lubricate Quik-Lok

®

Blade Clamp with a dry lubricant

such as graphite.

8' Quik-Lok

®

Cord

Cat. No. 48-76-4008

25' Quik-Lok

®

Cord

Cat. No. 48-76-4025

1/2" Blade Clamp Kit

Cat. No. 49-22-5016

20 mm Blade Clamp Kit

Cat. No. 49-22-5004

Impact Resistant Carrying Case

Cat. No. 50-55-6506

Steel Carrying Case

Cat. No. 48-55-1535

Easy-Cut Sawzall Blade Lubricant

Cat. No. 49-08-4206

For MILWAUKEE Sawzall

®

Blades, refer to the blade listing at the end

of the manual.

Maintaining Tools

Keep your tool in good repair by adopting a regular maintenance pro-

gram. Before use, examine the general condition of your tool. Inspect

guards, switches, tool cord set and extension cord for damage. Check

for loose screws, misalignment, binding of moving parts, improper mount-

ing, broken parts and any other condition that may affect its safe opera-

tion. If abnormal noise or vibration occurs, turn the tool off immediately

and have the problem corrected before further use. Do not use a dam-

aged tool. Tag damaged tools DO NOT USE until repaired

(see Repairs).

Under normal conditions, relubrication is not necessary until the motor

brushes need to be replaced. After six months to one year, depending on

use, return your tool to the nearest MILWAUKEE service facility for the

following:

 Lubrication

 Brush inspection and replacement

 Mechanical inspection and cleaning (gears, spindles, bearings,

housing, etc.)

 Electrical inspection (switch, cord, armature, etc.)

 Testing to assure proper mechanical and electrical operation

MAINTENANCE

Cleaning

Clean dust and debris from vents. Keep the tool handles clean, dry and

free of oil or grease. Use only mild soap and a damp cloth to clean your

tool since certain cleaning agents and solvents are harmful to plastics

and other insulated parts. Some of these include: gasoline, turpentine,

lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia

and household detergents containing ammonia. Never use flammable or

combustible solvents around tools.

Repairs

If your tool is damaged, return the entire tool to the nearest service

center.

WARNING!

To reduce the risk of injury, always unplug your tool before

performing any maintenance. Never disassemble the tool or

try to do any rewiring on the tool's electrical system. Contact

a MILWAUKEE service facility for ALL repairs.

WARNING!

To reduce the risk of injury, electric shock and damage to the

tool, never immerse your tool in liquid or allow a liquid to flow

inside the tool.

ACCESSORIES

To reduce the risk of injury, always unplug the tool before

attaching or removing accessories. Use only specifically

recommended accessories. Others may be hazardous.

WARNING!

FIVE YEAR TOOL LIMITED WARRANTY

Every MILWAUKEE tool is tested before leaving the factory and is war-

ranted to be free from defects in material and workmanship. MILWAUKEE

will repair or replace (at MILWAUKEEs discretion), without charge, any

tool (including battery chargers) which examination proves to be defec-

tive in material or workmanship from five (5) years after the date of

purchase. Return the tool and a copy of the purchase receipt or other

proof of purchase to a MILWAUKEE Factory Service/Sales Support

Branch location or MILWAUKEE Authorized Service Station, freight pre-

paid and insured. This warranty does not cover damage from repairs

made or attempted by other than MILWAUKEE authorized personnel,

abuse, normal wear and tear, lack of maintenance, or accidents.

Battery Packs, Flashlights, and Radios are warranted for one (1) year

from the date of purchase.

THE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN ARE

EXCLUSIVE. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY

INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES, INCLUDING

LOSS OF PROFITS.

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRAN-

TIES, OR CONDITIONS, WRITTEN OR ORAL, EXPRESSED OR IMPLIED FOR

MERCHANTABLILITY OR FITNESS FOR PARTICULAR USE OR PURPOSE.

This warranty gives you specific legal rights. You may also have other

rights that vary from state to state and province to province. In those

states that do not allow the exclusion of implied warranties or limitation

of incidental or consequential damages, the above limitations or exclu-

sions may not apply to you. This warranty applies to the United States,

Canada, and Mexico only.

For a complete listing of accessories refer to your MILWAUKEE Electric

Tool catalog or go on-line to www.milwaukeetool.com. To obtain a

catalog, contact your local distributor or a service center.

Page is loading ...

page 23

Super Sawzall Blades Lames Super Sawzall Bimétalliques Seguetas Bi-Metálicas Sawzall

Length x Width

Longueur x Largeur

Largo x Ancho

/

 Cat. No.

2 per pouch

 No de Cat.

2 par sachet

 Cat. No.

2 por sobre

48-02-5011

48-02-5012

48-02-5031

48-02-5035

48-02-5036

48-02-5037

48-02-5041

48-02-5052

48-02-5090

48-02-5092

48-02-5091

48-02-5093

48-02-5094

48-02-5193

48-02-5194

48-02-5161

48-02-5162

48-02-5163

48-02-5181

48-02-5182

48-02-5282

48-02-5187

48-02-5183

48-02-5184

48-02-5284

48-02-5188

48-02-5189

48-02-5185

48-02-5186

48-02-5286

--

48-00-8700

48-00-8705

48-00-8710

--

Inches

4 x 3/4

6 x 3/4

9 x 3/4

12 x 3/4

6 x 1/2

5 x 3/4

4 x 3/4

6 x 3/4

8 x 3/4

12 x 3/4

8 x 5/8

12 x 5/8

3-5/8 x 5/16

4 x 3/4

6 x 3/4

6 x 5/8

9 x 3/4

4 x 3/4

6 x 3/4

6 x 5/8

9 x 3/4

12 x 3/4

4 x 3/4

6 x 3/4

6 x 5/8

6 x 1

9 x 1

12 x

6 x 1

9 x 1

12 x 1

6 x 1

9 x 1

6 x 1

9 x 1

6 x 1

9 x 1

12 x 1

mm

102 x 19

152 x 19

229 x 19

305 x 19

152 x 13

127 x 19

102 x 19

152 x 19

203 x 19

305 x 19

203 x 16

305 x 16

92 x 8

102 x 19

152 x 19

152 x 16

229 x 19

102 x 19

152 x 19

152 x 16

229 x 19

305 x 19

102 x 19

152 x 19

152 x 16

152 x 25

229 x 25

305 x 25

152 x 25

229 x 25

305 x 25

152 x 25

229 x 25

152 x 25

229 x 25

152 x 25

229 x 25

305 x 25

 Cat. No.

5 per pouch

 No de Cat.

5 par sachet

 Cat. No.

5 por sobre

48-01-5011

48-01-5012

48-01-5031

48-01-5035

48-01-5036

48-01-5037

48-01-5041

48-01-5052

48-01-5090

48-01-5092

48-01-5091

48-01-5093

48-01-5094

48-01-5193

48-01-5194

48-01-5161

48-01-5162

48-01-5163

48-01-5181

48-01-5182

48-01-5282

48-01-5187

48-01-5183

48-01-5184

48-01-5284

48-01-5188

48-01-5189

48-01-5185

48-01-5186

48-01-5286

48-00-5021

48-00-5026

48-00-5027

48-00-5700

48-00-5705

48-00-5710

48-00-5712

48-00-5713

48-00-5782

48-00-5787

48-00-5784

48-00-5788

48-00-5789

 Teeth Per Inch /25 mm

 Dents/25 mm (1")

 Dientes x 25 mm

6

5/8

6

4/6

6

10

8/12

10/14

10

14

18

14

18

24

5/8

8

10

14

18

Wood Cutting Blades  Lames à Couper Le Bois  Seguetas Para Cortar Madera

For cutting wood, nail-embedded wood, composition materials.  Coupe de bois, bois cloué,

agglomérés.  Para cortar madera, madera con clavos y materiales compuestos.

Wood Cutting Blades  Lames À Couper Le Bois  Seguetas Para Cortar Madera

For cutting wood, nail-embedded wood, general roughing-in, all purpose.  Coupe de bois, bois cloué,

dégrossissage général, tout usage.  Para cortar madera, madera con clavos, cortes en general en bruto.

Plaster Cutting Blade  Lame À Couper Le Plâtre  Seguetas Para Cortar Materiales Emplastados

For cutting plaster with metal lath.  Coupe de plâtre et lattis métallique.  Para cortar emplastados con respaldo de metal.

All Purpose Blades  Lames Tout Usage  Seguetas Para Cortes En General

For cutting wood, nail-embedded wood, plastics, fiberglass, metals, cast iron.  Pour coupe de bois, bois cloué, plastique,

fibre de verre, métaux et fonte.  Para cortar madera, madera con clavos, plasticos, fibra de vidrio, metales y hierro.

Metal Scroll Cutting Blades  Lame Pour Tailler Et Découper Dans Le Métal  Seguetas Para Calar En Metal

For cutting metal, scroll cutting.  Pour tailler et découper dans le métal.  Para cortar metal, en cortes calados.

Metal Cutting Blades  Lames à Métal  Seguetas Para Cortar Metal

For heavy gauge metal, fiberglass.  Métaux épais, fibre de verre.  Para metal de calibres gruesos y fibra de vidrio.

Ax Blades  Ax Baldes  Hojas Ax

Thicker extra wide blades for plunge cutting and demolition work.  Lames extra larges et plus épaisses pour coupes en

plongée et travaux de démolition.  Hojas extra anchas y más gruesas para cortes penetrantes y tareas de demolición.

Torch Blades  Torch Blades  Hojas Torch

Thicker, extra wide blades for metal cutting.  Lames extra larges et plus épaisses pour coupe du

métal.  Hojas extra anchas y más gruesas para cortes de metales.

58-14-4125d4 10/04 Printed in USA

MILWAUKEE ELECTRIC TOOL CORPORATION

13135 West Lisbon Road  Brookfield, Wisconsin, U.S.A. 53005

UNITED STATES

MILWAUKEE Service

MILWAUKEE prides itself in producing a

premium quality product that is

NOTHING BUT HEAVY DUTY

®

.

Your satisfaction with our products is

very important to us!

If you encounter any problems with the

operation of this tool, or you would like to

locate the factory Service/Sales Support Branch

or authorized service station nearest you,

please call...

1-800-SAWDUST

(1.800.729.3878)

NATIONWIDE TOLL FREE

Monday-Friday  8:00 AM - 4:30 PM  Central Time

or visit our website at

www.milwaukeetool.com

For service information, use the 'Service Center

Search' icon found in the 'Parts & Service' section.

Additionally, we have a nationwide network of

authorized Distributors ready to assist you with your

tool and accessory needs. Check your Yellow Pages

phone directory under Tools-Electric for the names

& addresses of those nearest you or see the

'Where To Buy' section of our website.

Corporate After Sales Service - Technical Support

Brookfield, Wisconsin USA

Technical Questions Service/Repair Questions Warranty

1-800-SAWDUST

(1.800.729.3878)

fax:1.800.638.9582

email: [email protected]

Monday-Friday  8:00 AM - 4:30 PM  Central Time

CANADA

Service MILWAUKEE

MEXICO

Servicios de MILWAUKEE

Milwaukee Electric Tool

Blvd. Abraham Lincoln no. 13

Colonia Los Reyes Zona Industrial

Tlalnepantla, Edo. México C.P. 54073

Tel. 55 5565-1414 Fax: 55 5565-6874

Adicionalmente, tenemos una red nacional de

distribuidores autorizados listos para ayudarle con

su herramienta y sus accesorios. Por favor, llame

al 55 5565-1414 para obtener los nombres y

direcciones de los más cercanos a usted, o consulte

la sección Where to buy (Dónde comprar) de

nuestro sitio web en

www.milwaukeetool.com

Notre réseau national de distributeurs agréés se tient

à votre disposition pour fournir laide technique,

loutillage et les accessoires nécessaires. Composez

le 416.439.4181 pour obtenir les noms et adresses

des revendeurs les plus proches ou bien consultez

la section «Où acheter» sur notre site web à ladresse

www.milwaukeetool.com

MILWAUKEE est fier de proposer un produit de

première qualité N

OTHING BUT HEAVY DUTY

®

. Votre

satisfaction est ce qui compte le plus!

En cas de problèmes dutilisation de loutil ou

pour localiser le centre de service/ventes ou le

centre dentretien le plus proche, appelez le...

416.439.4181

fax: 416.439.6210

Milwaukee Electric Tool (Canada) Ltd

755 Progress Avenue

Scarborough, Ontario M1H 2W7

Milwaukee 6519 Series User manual

This manual is also suitable for

Milwaukee 6519 Series User manual

in other languages

Related papers

Other documents