ITC EWS-XYZ-A User manual

Brand: ITC

Model: EWS-XYZ-A

Type: User manual

ITC EWS-XYZ-A is an Ethernet Webpage Server that acts as a bridge between Ethernet and CAN J1939 protocol, allowing you to control and customize your ITC VersiColor RGB lighting system through a user-friendly web interface. With the server, you can create custom scenes, adjust colors, set timers, and choose from various fade and chasing effects. It requires an ITC VersiControl RGB(W) controller and can connect to a digital dash for a more intuitive user experience. The server also features a help button with a QR code that links to the ITC website for additional information and FAQs.

3030 Corporate Grove Dr.

Hudsonville, MI 49426

Phone: 616.396.1355

itc-us.com

INSTALLATION CONSIDERATIONS

• The Ethernet Webpage Server is part of the ITC VersiColor line of RGB products. Lighting and additional controller products need to

be purchased separately. Refer to the installation instructions for these products for additional considerations.

• The Ethernet Webpage Server is a bridge between Ethernet and CAN J1939 protocol.

• An ITC VersiControl RGB(W) controller must be used to connect to the Webpage Server. Please contact your ITC sales representative

for available options.

• Disconnect power before installing, adding or changing any component.

• To avoid a hazard to children, account for all parts and destroy all packing materials.

• This device complies with FCC part 15B regulations.

PARTS/TOOLS NEEDED:

Ethernet Server & CAN Connector Cable RGB(W) or ARGB(W) Controller

(purchased separately)

Digital Dash

(purchased separately)

OEM SET UP INFORMATION

• To adjust configuration settings, first press the help button, then system info button.

• Select zone info, this will display the current settings of a zone. Select a zone on the left to show it’s settings.

• To change them, press either zone setup or controller setup.

• Note: You must enter a password in order to make changes to the settings.

• To find the version number, push the help button on the main screed.

1. System Connections

HTML Server RGB(W) Controller Digital Dash

CAN Connector

CANEthernet

RJ 45

C-Size

Connector

To lights

(2 or 4 zones)

Incoming Power (2)

To boat dash

3.5mm Audio Input

Signal/Disable

Line (White,

1-4)

810-00530

2’ cable Ethernet Cable

(Not provided)

INSTALLATION INSTRUCTIONS

Ethernet Webpage

Server

Part#: EWS-XYZ-A

For warranty information please visit www.itc-us.com/warranty-return-policy

DOC #: 710-00174 • Rev B • 05/18/22

Page 1 of 4

3030 Corporate Grove Dr.

Hudsonville, MI 49426

Phone: 616.396.1355

itc-us.com

2. Open ITC lighting control screen

3. Color control screen

- Turn on power to system. The MFD will display a button called “ITC Marine VersiControl”. Press and the main lighting screen will

open.

- Note: When using the keyboard to rename zones or scenes, you must touch an area outside of the keyboard to close it.

- In the help screen, there is system info screen that will provide revision information.

Zone Titles

Long press to bring up the

keyboard and rename the

zones for easy identiﬁcation

Zone On/Off Button

To clear a scene on a zone,

turn it off and on again

Zone Selection

Check mark indicates that

zone is selected for modiﬁ-

cation

Custom Scenes

Touch to activate a scene and

touch again to deactivate

Instant White

Changes all zones to white,

no other modiﬁcations can

be made until the Instant

White is turned off

Set Color

Set static colors for a partic-

ular zone

Help

Brings up a QR code that

opens the ITC website for

more information. Also pro-

vides access to the current

conﬁguration

System On/Off

Turns all zones off and saves

current settings

- On the main screen, select your zones then press the set color button.

Zone being modiﬁed

Add color favorites

Long press to save

up to eight colors

Save settings

Brightness level

If using a RGBW controller,

an additional slider bar will

be shown for the white

Color slider bar

Custom RGB color

The color can be set based

on a speciﬁc RGB value. A

keyboard will open when

pressed

Cancel changes

For warranty information please visit www.itc-us.com/warranty-return-policy

DOC #: 710-00174 • Rev B • 05/18/22

Page 2 of 4

3030 Corporate Grove Dr.

Hudsonville, MI 49426

Phone: 616.396.1355

itc-us.com

5. Standard fades screen

- Select the color fade button on the scene set up menu.

4. Scene setup screen

- Hold add scene button and the scene setup screen will appear.

- Note, the ethernet web server will not come with any preset scenes. These must be set by the OEM or end consumer.

- When entering a mode you must select the zones ﬁrst.

Fade speed

Standard fade options

Select from ﬁve preset fade

options

Zone Selection

Make sure to check all

zones the effect should

be applied to

Color mode

Select the static color

for the lights

Color fade

Select from standard fades

and adjust fade speed

Custom scene name

Timer mode

Set a timer to turn the lights

on or off for a selected zone

Music mode

Sets music mode

Save scene setting

Set all selected zones to the

desired scene and press save

Scroll bar

Scroll to get to custom fades

and chasing (if applicable)

Custom color fade

Space for up to four custom

color fade modes

For warranty information please visit www.itc-us.com/warranty-return-policy

DOC #: 710-00174 • Rev B • 05/18/22

Page 3 of 4

3030 Corporate Grove Dr.

Hudsonville, MI 49426

Phone: 616.396.1355

itc-us.com

Problem Solution

No zones are visible Check to make sure the controller is connected and make sure to reset both

the server and the controller

Page is stuck on loading Check to make sure the controller is connected properly

Reset or sync the fade on multiple screens Return to the main screen and turn the instant white button on and off

Screen is ﬂickering If you are using two controllers, they may be set to the same address, change

the address of one

Access is needed for the set up screens You will need to use a password - set up screens should only be accessed by

OEM suppliers

The server ﬁrmware needs to be updated Contact ITC sales representative for instructions

Scenes not functioning properly Remove scene and start over by going to scene edit and pressing the delete

button, restart scene set up

Additional help needed Press the help button and scan the QR code to pull up FAQ and more infor-

mation on the ITC website

TROUBLESHOOTING

7. Music mode screen

6. Chasing mode screen

Standard chasing modes

Custom strips

Custom strips are based on

custom fade colors

Color width

Adjust the number of LED

banks that will be illuminat-

for a certain effect

Direction/speed

Set chasing effect direction

and speed

Brightness

Adjusts the brightness of the

lights to the beat of the

music

Brightness and Color

Adjusts both the color and

brightness of the lights to

the beat of the music

Audio Sensitivity

Adjust slider bar for

more or less sensitivity

(if applicable)

- Applies only if an ARGB(W) controller is connected.

For warranty information please visit www.itc-us.com/warranty-return-policy

DOC #: 710-00174 • Rev B • 05/18/22

Page 4 of 4

ITC EWS-XYZ-A User manual

ITC EWS-XYZ-A User manual

Related papers

Other documents