PAGE 1 OF 17
For questions about your
appliance, please call 1-800-626-2000. Product Specication Revised 1/22
FLUSH INSET INSTALLATION
Allows the refrigerator to be installed ush with adjacent
cabinetry
CUSTOM APPEARANCE
Allows personalization with cabinet-compatible panels
and custom handles
UPFRONT ELECTRONIC CONTROLS WITH
DIGITAL READOUT
Allows precise temperature settings and are positioned
for maximum ease of use
HUMIDITY CONTROLLED VEGETABLE
COMPARTMENTS AND SEALED SNACK PANS
Help maintain freshness and help preserve foods longer
ADJUSTABLE, SPILL PROOF GLASS SHELVES
Make it easy to customize storage to handle foods
and containers of various sizes
2 SEALED DELI PANS WITH FULL
EXTENSION SLIDES
SIX ADJUSTABLE DOOR BINS
Oer added storage exibility
GE WATER™ FILTRATION SYSTEM
Delivers clean, great tasting ice
MONOGRAM 36" BUILT-IN
BOTTOM-FREEZER REFRIGERATOR
ZIC360NNRH
For questions about your
appliance, please call 1-800-626-2000.
STANDARD INSTALLATION
SECTION 2
SECTION 1
FLUSH INSET INSTALLATION
PAGE 2 OF 17 Product Specication Revised 1/22
1/4" FRAMED PANELS 3/4" OVERLAY PANELS
REQUIRES ADDITIONAL TRIM KIT ZKFN
For questions about your
appliance, please call 1-800-626-2000.
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.
OVERALL DIMENSIONS
PAGE 3 OF 17 Product Specication Revised 1/22
SPECIFICATIONS
Overall Width 36" (91.4 cm)
Overall Height 84" (213.4 cm)
Overall Depth 25 1/4" (64.1cm)
Door Clearance 36 1/2" (92.7 cm)
Cutout Width 35 1/2" (90.2 cm)
Cutout Height 83 1/2" - 84 1/2"
(212.1 - 214.6 cm)
Cutout Depth 24" (61 cm)
Plumbing Requirements 1/4" OD copper tubing or
GE SmartConnect kit
Shipping Weight 640 lb (290 kg)
25 1/4" (64.1)
23 5/8" (60.0)
10"
(25.4)
36" (91.5)
*84"
(213.4)
*3 5/8"
(9.2) SIDE VIEWFRONT VIEW
*83 1/2"
(212.1)
36 3/4"
(93.3)
35" (88.9)
Case width
TOP VIEW
ZIC360NXRH
* Shipping height. Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
** 4 9/16" (11.6) min
clearance to a wall
for 90˚ door swing
** Dimensions based on custom handle height of 2 9/16" (6.5).
3/4"
(1.9)
73 1/4"
(186.1)
** Allow 25" (63.5) min
clearance for 130˚
door swing
** These refrigerators are equipped with a 3-position door stop. The
factory-set 130° door swing can be adjusted to 90° or 130° for
standard installation if clearances to adjacent cabinets or walls is
restricted. Allow a 15" minimum clearance to wall for pan removal. If
the 90° door stop position is used, pan access is maintained, but pan
removal is restricted.
STANDARD INSTALLATION
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
Product Specication Revised 1/22
24" (61)
1 9/16"
(3.97)
35 1/2" (90.2)
2 5/16"
(5.874)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
*84 +
- .500
(212.1-214.6)
*Trim will overlap
additional 7/16"
6"
(15.24)
10"
(25.4)
ELEC.
SIDE VIEW FRONT VIEW
TOP VIEW
W
STANDARD INSTALLATION
ZIC360NHLH_RH
WATER
5"
(12.7)
5"
(12.7)
3 1/2"
(9.0) 3 1/2"
(8.9)
HELPFUL TIPS
For questions about your
appliance, please call 1-800-626-2000.
STANDARD INSTALLATION
PAGE 4 OF 17
A Mounting the junction box in
this location will also allow for
front accessibility through access
panel.
B Water supply area.
WARNING:
The refrigerator is top heavy and
must be secured to prevent the
possibility of tipping forward.
Failure to do so may result in
death or serious injury.
The information below is for
cabinet design only. When
installing the anti-tip system you
must use the product installation
instructions.
The information below applies to
all installation constructions:
• A wall bracket, bolts and toggles
will be supplied with the unit.
• The bolts will be used to attach
bracket to wall in 4 locations. Two
of the locations must penetrate the
center of the wall studs.
• The toggles are used for stability
in drywall and when metal studs
are encountered. Lag bolts are
used in wood studs.
• In installation opening, measure
81-1/2" from oor and draw a
horizontal line.
• Locate and mark the wall studs on
horizontal line. Verify at least two
studs have their centerlines within
the center 32-1/2" of installation
opening to ensure 2 wall studs are
penetrated.
• The bracket will be centered left
to right in opening with bottom
of bracket on the horizontal line.
• When unit is placed in opening,
the bracket tabs will align with
openings in back of the unit. The
unit will be secured to the bracket
using supplied “L” bolts.
See Installation Instructions for
detailed instructions.
A
STANDARD INSTALLATION
ANTI-TIP BRACKET
ZIC360NXRH
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
81 1/2"
(207.0)
Use two
additional hole
locations at end
of brackets
Wall
Studs
Bracket
mounted
into vertical
wall studs
centered
within the
cutout
C
Ensure holes
selected are
centered on
the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
B
Product Specication Revised 1/22
HELPFUL TIPS
For questions about your
appliance, please call 1-800-626-2000.
STANDARD INSTALLATION
PAGE 5 OF 17
PANEL ASSEMBLY CROSS SECTION
PANEL ASSEMBLY CROSS SECTION
PANEL DIMENSIONS
PANEL DIMENSIONS
STANDARD 3/4" OVERLAY PANEL DIMENSIONS SINGLE INSTALLATION
STANDARD 1/4" FRAMED PANEL DIMENSIONS SINGLE INSTALLATION
A B C D
1/4" Framed Panel 33 7/8" 8 7/8" 46 1/16" 21 7/8"
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
B
C
D
Door
1/4" Framed Panel
Optional ZKLN kit handle
Trim
A B C D
1/4" Backer Panel 33 7/8" 8 7/8" 46 1/16" 21 7/8"
.10" Spacer Panel 32 1/2" 7 5/8" 44 11/16" 20 1/2"
3/4" Overlay Panel 34 1/8" 9" 46 5/16" 22"
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
B
C
D
Door 1/4" Backer Panel
.10" Spacer Panel
Optional ZKLN kit handle
Trim
3/4" Overlay Panel
3/4" OVERLAY PANELS:
The decorative panels slide into the
trim. The overlay panel must be
secured to a 1/4"-thick backer panel
which slides into the trim. A spacer
panel 0.10" thick must be placed
between the overlay and backer
panels. Center each panel over the
other. Assemble the panels with
glue and screws. Screws must be
countersunk into the backer panel.
NOTE: Left-to-right oset is not
always equal to top-to-bottom oset.
MAXIMUM TOTAL PANEL
WEIGHT:
• Fresh food door panel – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 11 lbs.
DOOR HANDLES:
Door panels not included. Custom
handles supplied by your cabinet
maker may be used
Optional visor handle kit ZKLN
available.
Trimmed refrigerators are designed
to be customized with decorative
panels. Field-installed custom door
and grille panels are required.
1/4" FRAMED PANELS:
For 1/4" thick custom panels
ordered from your cabinet maker.
The decorative panels slide into the
trim.
MAXIMUM TOTAL PANEL
WEIGHT:
• Fresh food door panel – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 11 lbs.
.25" + .10" + .75" = 1.10" Total Panel Thickness
Product Specication Revised 1/22
HELPFUL TIPS
For questions about your
appliance, please call 1-800-626-2000.
STANDARD INSTALLATION
PAGE 6 OF 17
F Side panels must be used
whenever the sides of the
refrigerator will be exposed.
The 1/4" side panels will slip
into the side case trim. Secure
the panels to the refrigerator
with stick-on hook and loop
fastener strips. Order the
side panels from the cabinet
manufacturer.
CUSTOM SIDE PANELS
F
2 9/16"
(6.5)
*3"- 4"
(7.6 - 10.2)
*Depending
on installation
height
1 7/8"
(4.8)
24" (61.0)
3/16"
(.5)
*84"
(213.4)
*Depending
on installation
height
ZIF360NXLH_ZIF360NXRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH
ZIR360NXLH_ZIR360NXRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH
For questions about your
appliance, please call 1-800-626-2000.
FLUSH INSET INSTALLATION
HELPFUL TIPS
PAGE 7 OF 17 Product Specication Revised 1/22
PANEL ASSEMBLY
CROSS SECTION
HELPFUL TIPS
For questions about your
appliance, please call 1-800-626-2000.
STANDARD INSTALLATION
PAGE 7 OF 17
STANDARD 1/4" FRAMED PANEL DIMENSIONS
DUAL INSTALLATION Trimmed refrigerators are designed
to be customized with decorative
panels. Field-installed custom door
and grille panels are required.
1/4" FRAMED PANELS:
For 1/4" thick custom panels
ordered from your cabinet maker.
The decorative panels slide into the
trim.
MAXIMUM TOTAL PANEL
WEIGHT:
• Fresh food door panel – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 25 lbs.
Order ZKBFN720NII unication
kit for an integrated appearance
on 2 custom panel models installed
side-by-side.
71 1/2" (181.6)
Finished Width
24" (60.9)
Min. Cutout Depth
24 3/16" (61.4)
2 5/16"
(5.9)
6"
(15.2)
10"
(25.4)
*84 +
- .500
(212.1-214.6)
Finished Opening
ZIC360NXLH_ZIC360NXRH_ZICP360NXLH_ZICP360NXRH
ZICS360NXLH_ZICS360NXRH
FRONT VIEW
ELEC. 6"
(15.2)
10"
(25.4)
3 1/2"
(8.9)
25" min
(63.5)
To wall
25" min
(63.5)
To wall
1"
(2.5)
130˚
Door swing 130˚
Door swing
75"
(190.5 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
5"
(12.7) 5"
(12.7)
WATER
10" (25.4)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
5 3/4"
(14.6) 5 3/4"
(14.6)
A A separate 115V, 60Hz, 15-
or 20-amp power supply is
recommended for each product.
Additional cutout width may be
required when side panels are used.
DUAL INSTALLATIONS
A
PANEL DIMENSIONS
A B C D E
1/4" Framed Panel 69 7/8" 8 7/8" 46 1/16" 21 7/8" 33 7/8"
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
Fresh
Food
Panel
Freezer Drawer Panel
E
B
C
D
E
Door
1/4" Framed Panel
Optional ZKLN kit handle
Trim
Product Specication Revised 1/22
HELPFUL TIPS
For questions about your
appliance, please call 1-800-626-2000.
STANDARD INSTALLATION
PAGE 8 OF 17
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
Fresh
Food
Panel
Freezer Drawer Panel
E
B
C
D
E
DUAL PRODUCT CLEARANCES
71 1/2" (181.6)
Finished Width
24" (60.9)
Min. Cutout Depth
24 3/16" (61.4)
2 5/16"
(5.9)
6"
(15.2)
10"
(25.4)
83 1/2" min
84 1/2" max
(212.1-214.6)
Finished Opening
ZIC360NXLH_ZIC360NXRH_ZICP360NXLH_ZICP360NXRH
ZICS360NXLH_ZICS360NXRH
FRONT VIEW
ELEC. 6"
(15.2)
10"
(25.4)
3 1/2"
(8.9)
23 7/8" min**
(60.6)
To wall
23 7/8" min**
(60.6)
To wall
1"
(2.5)
130˚
Door swing 130˚
Door swing
75"
(190.5 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
5"
(12.7) 5"
(12.7)
WATER
10" (25.4)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
5 3/4"
(14.6) 5 3/4"
(14.6)
** Dimensions based on custom
height of 2 9/16” (6.5)
A
STANDARD 3/4" OVERLAY PANEL DIMENSIONS
DUAL INSTALLATION
PANEL ASSEMBLY
CROSS SECTION
PANEL DIMENSIONS
1/4"
Backer
Panel
.10"
Spacer
Panel
3/4"
Overlay
Panel
A69 7/8" 68 1/2" 70 1/8"
B8 7/8" 7 5/8" 9"
C46 1/16" 44 11/16" 46 5/16"
D21 7/8" 20 1/2" 22"
E33 7/8" 32 1/2" 34 1/8"
.25" + .10" + .75" = 1.10" Total Panel
Thickness
Door
1/4" Backer Panel
.10" Spacer Panel
Optional ZKLN kit handle
Trim
3/4" Overlay Panel
3/4" OVERLAY PANELS:
The decorative panels slide into the
trim. The overlay panel must be
secured to a 1/4"-thick backer panel
which slides into the trim. A spacer
panel 0.10" thick must be placed
between the overlay and backer
panels. Center each panel over the
other. Assemble the panels with
glue and screws. Screws must be
countersunk into the backer panel.
NOTE: Left-to-right oset is not
always equal to top-to-bottom
oset.
MAXIMUM TOTAL PANEL
WEIGHT:
• Fresh food door panel – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 25 lbs.
Order ZKBFN720NII unication
kit for an integrated appearance
on 2 custom panel models installed
side-by-side.
DOOR HANDLES:
Door handle not included. Custom
handles supplied by your cabinet
maker may be used.
Optional visor handle kit ZKLN
available.
A In a side-by-side installation of a
left-and-right-hand door swing
product, 1" clearance between
the units is required.
For questions about your
appliance, please call 1-800-626-2000.
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.
OVERALL DIMENSIONS
AFTER PANEL INSTALL
FLUSH INSET
INSTALLATION
PAGE 9 OF 17 Product Specication Revised 1/22
† Dimensions include 3/4" custom cabinet panel
SPECIFICATIONS
Overall Width 38" (96.5 cm)†
Overall Height 84 1/2" (214.6 cm)†
Overall Depth 25 15/16" (65.9 cm)†
Door Clearance 38 3/4" (98.4 cm)
Cutout Width 39" (99.1 cm)
Cutout Height 85" (215.9 cm)
Cutout Depth 26 3/16" (66.5 cm)
Plumbing Requirements 1/4" OD copper tubing or
GE SmartConnect kit
Shipping Weight 640 lb (290 kg)
38" (96.5)
11 1/2"
(29.2)
26" (66.0)
* 84 1/2"
(214.6)
*73"
(185.4)
*26 7/16"
(67.1)
*4"
(10.2) SIDE VIEWFRONT VIEW
* 83 1/2"
(212.1)
35" (88.9)
Case width
38 3/4"
(98.4)
TOP VIEW
ZIC360NHRH
** 4 9/16" (11.6) min
clearance to a wall
for 90˚ door swing
* Shipping height. Use leveling legs and wheels for maximum 1" height
adjustment from shipping height. Nominal installation height is 84”
** Dimensions based on custom handle height of 2 9/16" (6.5).
20 5/8"
(52.5)
** Allow 15" (38.1) min
clearance for 115˚
door swing
20 5/8" (52.4)
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
Product Specication Revised 1/22
For questions about your
appliance, please call 1-800-626-2000.
FLUSH INSET INSTALLATION
HELPFUL TIPS
PAGE 10 OF 17
A Mounting the junction box in this
location will also allow for front
accessibility through access panel.
B Water supply area.
WARNING:
The refrigerator is top heavy and must
be secured to prevent the possibility of
tipping forward. Failure to do so may
result in death or serious injury.
The information below is for cabinet
design only. When installing the anti-
tip system you must use the product
installation instructions.
The information below applies to all
installation constructions:
• A wall bracket, bolts and toggles will
be supplied with the unit.
• The bolts will be used to attach bracket to
wall in 4 locations. Two of the locations
must penetrate the center of the wall
studs.
• The toggles are used for stability in drywall
and when metal studs are encountered. Lag
bolts are used in wood studs.
• In installation opening, measure 82" from
oor and draw a horizontal line.
• Locate and mark the wall studs on
horizontal line. Verify at least two studs
have their centerlines within the center
32-1/2" of installation opening to ensure
2 wall studs are penetrated.
• The bracket will be centered left to right
in opening with bottom of bracket on the
horizontal line.
• When unit is placed in opening, the
bracket tabs will align with openings in
back of the unit. The unit will be secured
to the bracket using supplied “L” bolts.
See Installation Instructions for detailed
instructions.
FLUSH INSTALLATION
ZIC360NHLH_RH
39" (99.1) Flush inset width
37 1/2" (95.3)
Width between cleats
3/4" (1.9)
Width of side cleats
5 1/4" (13.3)
1/2" (1.3)
26 3/16" (66.5)
Flush inset depth
20 15/16" (53.2)
Depth to cleat
FRONT VIEWSIDE VIEW
TOP VIEW
3 1/2"
(8.9)
W
Finished cleats
Finished cleats
Case Trim
3/4" Panel
Case
Door
6"
(15.2)
24 3/16"
(61.4)
7"
(17.8)
7"
(17.8)
10"
(25.4)
3 1/2"
(8.9)
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
84"
(213.4)
height
to cleat
85"
(215.9)
WATER
3 1/2"
(9.0)
FLUSH INSET INSTALLATION 3/4" PANELS
A
B
ANTI-TIP BRACKET
FLUSH INSET KIT ZKFN REQUIRED
ZIC360NXRH
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
81 1/2"
(207.0)
Use two
additional hole
locations at end
of brackets
Wall
Studs
Bracket
mounted
into vertical
wall studs
centered
within the
cutout
C
Ensure holes
selected are
centered on
the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
WARNING:
Door Trim Pinch Point Hazard
Improper installation can lead to a nger
pinch point hazard between the side door
trim and the cabinets when operating
the door, especially with children. To
minimize this risk you must follow
the installation instructions for cabinet
dimensions, trim assembly and door stop
angle.
Product Specication Revised 1/22
For questions about your
appliance, please call 1-800-626-2000.
FLUSH INSET INSTALLATION
HELPFUL TIPS
PAGE 11 OF 17
Trimmed refrigerators are designed
to be customized with decorative
panels. Field-installed 1/2" or 3/4"
custom door, drawer and grille
panels are required. For 3/4" raised
panels, routing is required. The
router depth is 1/4" all the way
around the panel’s backs. Additional
panel width reductions are required
per the diagrams shown. This
will create “picture frame’ routing
allowing the panels to slide into the
attached door, drawer and grille
trims.
MAXIMUM TOTAL PANEL
WEIGHT:
• Fresh food door panels – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 11 lbs
NOTE: For panels constructed with
rails and stiles (5-panel), the rails
must be a minimum of 3" wide
and stiles must be a minimum of
4" wide.
DOOR HANDLES
Door handles not included.Custom
handles supplied by your cabinet
maker may be used.
Order ZKBFN720NII unication
kit for an integrated appearance on
2 custom panel models installed
side-by-side.
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
B
C
D
A B C D
38" 10 11/16" 46 9/16" 22 7/16"
PANEL DIMENSIONS
FLUSH INSET 3/4" PANEL DIMENSIONS SINGLE INSTALLATION
3/4" RAISED DOOR PANEL ROUTING
3/4"
11/32"
1/4"
1/4"
1/4" 7/16"
DETAIL TOP
DETAIL BOTTOM
DETAIL
LEFT SIDE
DETAIL RIGHT
SIDE
2-1/16" 2-1/16"
ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"
1/4"
3/32"
TOP
FrontBack
BOTTOM
3/4" PANEL SIDE VIEW
(AFTER ROUTING)
3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
LEFT
SIDE
RIGHT
SIDE
Front
Back
Front
NOTE: Routed areas should
be finished as they may be
visible when assembled.
CORNER VIEW SHOWING
“PICTURE FRAME” ROUTING
Back
For questions about your
appliance, please call 1-800-626-2000.
FLUSH INSET INSTALLATION
HELPFUL TIPS
PAGE 12 OF 17 Product Specication Revised 1/22
3/4" RAISED GRILL PANEL ROUTING
TOP
FrontBack
BOTTOM
3/4" PANEL SIDE VIEW
(AFTER ROUTING)
DETAIL TOP
DETAIL BOTTOM
3/16"
1-11/16"
ROUTER DEPTH 1/4"
DETAIL
LEFT SIDE
DETAIL RIGHT
SIDE
2-1/16" 2-1/16"
ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"
1/4"
3/32"
3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
LEFT
SIDE
RIGHT
SIDE
Front
Back
Trimmed refrigerators are designed
to be customized with decorative
panels. Field-installed 1/2" or 3/4"
custom door, drawer and grille
panels are required. For 3/4" raised
panels, routing is required. The
router depth is 1/4" all the way
around the panel’s backs. Additional
panel width reductions are required
per the diagrams shown. This
will create “picture frame’ routing
allowing the panels to slide into the
attached door, drawer and grille
trims.
MAXIMUM TOTAL PANEL
WEIGHT:
• Fresh food door panels – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 11 lbs
NOTE: For panels constructed with
rails and stiles (5-panel), the rails
must be a minimum of 3" wide
and stiles must be a minimum of 4"
wide.
DOOR HANDLES
Door handles not included.Custom
handles supplied by your cabinet
maker may be used.
Order ZKBFN720NII unication
kit for an integrated appearance
on 2 custom panel models installed
side-by-side.
3/4" RAISED DRAWER PANEL ROUTING
Front
NOTE: Routed areas should
be finished as they may be
visible when assembled.
CORNER VIEW SHOWING
“PICTURE FRAME” ROUTING
Back
TOP
FrontBack
BOTTOM
3/4" PANEL SIDE VIEW
(AFTER ROUTING)
Front
NOTE: Routed areas should
be finished as they may be
visible when assembled.
CORNER VIEW SHOWING
“PICTURE FRAME” ROUTING
Back
3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
LEFT
SIDE
RIGHT
SIDE
Front
Back
3/4"
11/32"
1/4"
1/4"
1/4" 7/16"
DETAIL TOP
DETAIL BOTTOM
2 1/16" 2 1/16"
ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"
DETAIL
LEFT SIDE
DETAIL RIGHT
SIDE
Product Specication Revised 1/22
For questions about your
appliance, please call 1-800-626-2000.
FLUSH INSET INSTALLATION
HELPFUL TIPS
PAGE 13 OF 17
A Mounting the junction box in
this location will also allow for
front accessibility through access
panel.
B Water supply area.
WARNING:
The refrigerator is top heavy
and must be secured to prevent
the possibility of tipping forward.
Failure to do so may result in death
or serious injury.
The information below is for
cabinet design only. When
installing the anti-tip system you
must use the product installation
instructions.
The information below applies to all
installation constructions:
• A wall bracket, bolts and toggles
will be supplied with the unit.
• The bolts will be used to attach
bracket to wall in 4 locations. Two
of the locations must penetrate the
center of the wall studs.
• The toggles are used for stability
in drywall and when metal studs
are encountered. Lag bolts are
used in wood studs.
• In installation opening, measure
82" from oor and draw a
horizontal line.
• Locate and mark the wall studs on
horizontal line. Verify at least two
studs have their centerlines within
the center 32-1/2" of installation
opening to ensure 2 wall studs are
penetrated.
• The bracket will be centered left
to right in opening with bottom of
bracket on the horizontal line.
• When unit is placed in opening,
the bracket tabs will align with
openings in back of the unit. The
unit will be secured to the bracket
using supplied “L” bolts.
See Installation Instructions for
detailed instructions.
FLUSH INSTALLATION
ZIC360NHLH_RH
39" (99.1) Flush inset width
37 1/2" (95.3)
Width between cleats
3/4" (1.9)
Width of side cleats
5 3/8" (13.7)
1/2" (1.3)
26 3/16" (66.5)
Flush inset depth
20 13/16" (52.9)
Depth to cleat
FRONT VIEWSIDE VIEW
TOP VIEW
3 1/2"
(8.9)
W
Finished cleats
Finished cleats
Case Trim
1/2" Panel
Case
Door
6"
(15.2)
24 3/16"
(61.4)
7"
(17.8)
7"
(17.8)
10"
(25.4)
3 1/2"
(8.9)
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
84"
(213.4)
height
to cleat
85"
(215.9)
WATER
3 1/2"
(9.0)
FLUSH INSET INSTALLATION 1/2" PANELS
A
B
ANTI-TIP BRACKET
FLUSH INSET KIT ZKFN REQUIRED
ZIC360NXRH
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
81 1/2"
(207.0)
Use two
additional hole
locations at end
of brackets
Wall
Studs
Bracket
mounted
into vertical
wall studs
centered
within the
cutout
C
Ensure holes
selected are
centered on
the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
For questions about your
appliance, please call 1-800-626-2000.
FLUSH INSET INSTALLATION
HELPFUL TIPS
PAGE 14 OF 17 Product Specication Revised 1/22
The 1/2" overlay panel must be
secured to a .10" spacer panel and a
1/4" thick backer panel, which slides
into the trim.
ASSEMBLE THE PANELS
WITH GLUE AND SCREWS:
• Center the spacer panel on the
backer panel, left to right and top
to bottom. Secure the panels with
glue.
• Refer to the chart for locating
the backer panel to the overlay
panel. Secure the overlay panel
to the backer panel with glue
and screws. Screws must be
countersunk into the backer panel
Order ZKBFN720NII unication
kit for an integrated appearance
on 2 custom panel models installed
side-by-side.
NOTE: For panels constructed with
rails and stiles (5-panel), the rails must
be a minimum of 3" wide and stiles
must be a minimum of 4" wide.
FLUSH INSET 1/2" PANEL DIMENSIONS
A B C D
1/4" Backer Panel 33 7/8" 8 7/8" 46 1/16" 21 7/8"
.10" Space Panel 32 1/2" 7 5/8" 44 11/16" 20 1/2"
1/2" Overlay Panel 38" 10 11/16" 46 9/16" 22 7/16"
A B C D
Fresh Food Panel 2 1/16" 2 1/16" 5/16" 3/16"
Freezer Panel 2 1/16" 2 1/16" 5/16" 3/16"
Grille Panel 2 1/16" 2 1/16" 1 11/16" 3/16"
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
B
C
D
PANEL DIMENSIONS
C
D
A B
Grille Back
C
D
AB
Hinge Side
Backer with
Overlay Panel
Assembly
Door Panel Back
C
D
AB
Freezer Drawer
1/2"
Overlay
Panel
1/4"
Backer
Panel
Door
.10"
Spacer
PANEL DIMENSIONS
1/2" OVERLAY PANEL ROUTING DIMENSIONS
Product Specication Revised 1/22
For questions about your
appliance, please call 1-800-626-2000.
FLUSH INSET INSTALLATION
HELPFUL TIPS
PAGE 15 OF 17
Trimmed refrigerators are designed
to be customized with decorative
panels. Field-installed 1/2" or 3/4"
custom door, drawer and grille
panels are required. For 3/4" raised
panels, routing is required. The
router depth is 1/4" all the way
around the panel’s backs. Additional
panel width reductions are required
per the diagrams shown. This
will create “picture frame’ routing
allowing the panels to slide into the
attached door, drawer and grille
trims.
A A separate 115V, 60Hz, 15-
or 20-amp power supply is
recommended for each product.
MAXIMUM TOTAL PANEL
WEIGHT:
• Fresh food door panels – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Unied grille panel – 25 lbs
DOOR HANDLES
Door handles not included.Custom
handles supplied by your cabinet
maker may be used.
Order ZKBFN720NII unication
kit for an integrated appearance
on 2 custom panel models installed
side-by-side.
The 1/2" overlay panel must be
secured to a .10" spacer panel and a
1/4" thick backer panel, which slides
into the trim.
ASSEMBLE THE PANELS WITH
GLUE AND SCREWS:
• Center the spacer panel on the
backer panel, left to right and top
to bottom. Secure the panels with
glue.
• Refer to the chart for locating the
backer panel to the overlay panel.
Secure the overlay panel to the
backer panel with glue and screws.
Screws must be countersunk into
the backer panel
FLUSH INSET 1/2" PANEL DIMENSIONS DUAL INSTALLATION
PANEL DIMENSIONS
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
Fresh
Food
Panel
Freezer Drawer Panel
E
B
C
D
A B C D E
1/4" Backer Panel 69 7/8" 8 7/8" 46 1/16" 21 7/8" 33 7/8"
.10" Space Panel 68 1/2" 7 5/8" 44 11/16" 20 1/2" 32 1/2"
1/2" Overlay Panel 74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8"
3/4" OR 1/2" DUAL INSTALLATIONS
ZIC360NHLH_ZIC360NHRH
75" (190.5)
Finished Width
26 3/16" (66.5)
Min. Cutout Depth
24 3/16" (61.4)
4 5/16
"
(10.9)
5 1/2"
(13.9)
9"
(22.9)
85"
(215.9)
Finished
Opening
3 1/2"
(8.9)
W
FRONT VIEW
ELEC. 5 1/2"
(13.9)
9"
(22.9)
3 1/2"
(8.9)
15" (38.1) min
To wall 15" (38.1) min
To wall
1"
(2.5)
115˚
Door swing 115˚
Door swing
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
7"
(17.8) 7"
(17.8)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
7 1/2"
(19.1) 7 1/2"
(19.1)
A
Product Specication Revised 1/22
For questions about your
appliance, please call 1-800-626-2000.
FLUSH INSET INSTALLATION
HELPFUL TIPS
PAGE 16 OF 17
Grille Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
Fresh
Food
Panel
Freezer Drawer Panel
E
B
C
D
A B C D E
74 1/2" 10 11/16" 46 9/16" 22 7/16" 36 7/8"
PANEL DIMENSIONS
FLUSH INSET 3/4" PANEL DIMENSIONS DUAL INSTALLATION
Trimmed refrigerators are designed
to be customized with decorative
panels. Field-installed 1/2" or 3/4"
custom door, drawer and grille
panels are required. For 3/4" raised
panels, routing is required. The
router depth is 1/4" all the way
around the panel’s backs. Additional
panel width reductions are required
per the diagrams shown. This
will create “picture frame’ routing
allowing the panels to slide into the
attached door, drawer and grille
trims.
MAXIMUM TOTAL PANEL
WEIGHT:
• Fresh food door panels – 58 lbs.
• Freezer drawer panel – 28 lbs.
• Unied grille panel – 25 lbs
DOOR HANDLES
Door handles not included.Custom
handles supplied by your cabinet
maker may be used.
Order ZKBFN720NII unication
kit for an integrated appearance on 2
custom panel models installed side-
by-side.
3/4" RAISED DOOR AND DRAWER PANEL ROUTING -
(SEE PAGE 11 FOR 3/4" GRILLE PANEL ROUTING DIAGRAMS)
TOP
FrontBack
BOTTOM
3/4" PANEL SIDE VIEW
(AFTER ROUTING)
Front
NOTE: Routed areas should
be finished as they may be
visible when assembled.
CORNER VIEW SHOWING
“PICTURE FRAME” ROUTING
Back
HINGE
SIDE
HANDLE
SIDE
Front
Back
3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
3/4"
11/32"
1/4"
3/16"
1/4" 7/16"
DETAIL TOP
DETAIL BOTTOM
2 1/16" 3/16"
ROUTER DEPTH 1/4"
DETAIL HINGE
SIDE
DETAIL HANDLE
SIDE
Product Specication Revised 1/22
For questions about your
appliance, please call 1-800-626-2000.
FLUSH INSET INSTALLATION
HELPFUL TIPS
PAGE 17 OF 17
A In a side-by-side installation
of a left-and-right-hand door
swing product, 1" clearance
between the units is required.
Order ZKBFN720NII
unication kit for an integrated
appearance on 2 custom panel
models installed side-by-side.
3/4" OR 1/2" DUAL PRODUCT CLEARANCES
ZIC360NHLH_ZIC360NHRH
75" (190.5)
Finished Width
26 3/16" (66.5)
Min. Cutout Depth
24 3/16" (61.4)
4 5/16"
(10.9)
5 1/2"
(13.9)
9"
(22.9)
85"
(215.9)
Finished
Opening
3 1/2"
(8.9)
W
FRONT VIEW
ELEC. 5 1/2"
(13.9)
9"
(22.9)
3 1/2"
(8.9)
16 7/8" (42.9) min**
To wall 16 7/8" (42.9) min**
To wall
1"
(2.5)
115˚
Door swing 115˚
Door swing
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
7"
(17.8) 7"
(17.8)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
7 1/2"
(19.1) 7 1/2"
(19.1)
** Dimensions based on custom
handle height of 2 9/16”
A
/