ROSIERES RFC3CS3259IN User manual

Category
Ovens
Type
User manual

This manual is also suitable for

USER INSTRUCTIONS
OVENS
NOTICE D'EMPLOI ET D'INSTALLATION
DES FOURS ENCASTRABLES
EN
FR
02
16
USINES DE ROSIÈRES - 30, rue Y. LACELLE - Rosières - 18400 - Lunery - France
Safety Indications
EN 02
When you open the door after you have finished cooking, a few
drops of water may come out of the door. It depends on the type of
food you have cooked.
• During cooking, moisture may condense inside the oven cavity or
on the glass of the door. This is a normal condition. To reduce this
effect, wait 10-15 minutes after turning on the power before putting
food inside the oven. ln any case, the condensation disappears when
the oven reaches the cooking temperature.
Cook the vegetables in a container with a lid instead of an open tray.
Avoid leaving food inside the oven after cooking for more than
15/20 minutes.
• WARNING: the appliance and accessible parts become hot during
use. Be careful not to touch any hot parts.
WARNING: the accessible parts can become hot when the grill is in
use. Children should be kept at a safe distance.
WARNING: ensure that the appliance is switched off before
replacing the bulb, to avoid the possibility of electric shocks.
WARNING: in order to avoid any danger caused by the accidental
resetting of the thermal interruption device, the appliance should
not be powered by an external switching device, such as a timer, or
be connected to a circuit that is regularly switched on and off.
Children under 8 should be kept at a safe distance from the
appliance if not continuously supervised.
Children should not play with the appliance.
The appliance can be used by those aged 8 or over and by those
with limited physical, sensorial or mental capacities, without
experience or knowledge of the product, only if supervised or
provided with instruction as to the operation of the appliance, in a
safe way with awareness of the possible risks.
Cleaning and maintenance should not be carried out by
unsupervised children.
• Do not use rough or abrasive materials or sharp metal scrapers to
clean the oven door glasses, as they can scratch the surface and
cause the glass to shatter.
The oven must be switched off before removing the removable
EN 03
parts. After cleaning, reassemble them according the instructions.
Only use the meat probe recommended for this oven.
Do not use a steam cleaner for cleaning operations.
Connect a plug to the supply cable that is able to bear the voltage,
current and load indicated on the tag and having the earth contact.
The socket must be suitable for the load indicated on the tag and
must have ground contact connected and in operation. The earth
conductor is yellow-green in colour. This operation should be carried
out by a suitably qualified professional. ln case of incompatibility
between the socket and the appliance plug, ask a qualified
electrician to substitute the socket with another suitable type. The
plug and the socket must be conformed to the current norms of the
installation country. Connection to the power source can also be
made by placing an omnipolar breaker between the appliance and
the power source that can bear the maximum connected load and
that is in line with current legislation. The yellow-green earth cable
should not be interrupted by the breaker. The socket or omnipolar
breaker used for the connection should be easily accessible when the
appliance is installed.
• The disconnection may be achieved by having the plug accessible
or by incorporating a switch in the fixed wiring in accordance with the
wiring rules.
lf the power cable is damaged, it should be substituted with a cable
or special bundle available from the manufacturer or by contacting
the customer service department. The type of power cable must be
H05V2V2-F. This operation should be carried out by a suitably
qualified professional. The earth conductor (yellow-green) must be
approximately 10 mm longer than the other conductors. For any
repairs, refer only to the Customer Care Department and request the
use of original spare parts.
Failure to comply with the above can compromise the safety of the
appliance and invalidate the guarantee.
Any excess of spilled material should be removed before cleaning.
A long power supply failure during an occurring cooking phase may
cause a malfunction of the monitor. ln this case contact customer
service.
The appliance must not be installed behind a decorative door in
order to avoid overheating.
When you place the shelf inside, make sure that the stop is directed
upwards and in the back of the cavity. The shelf must be inserted
completely into the cavity.
WARNING: Do not line the oven walls with aluminium foil or single-
use protection available from stores. Aluminium foil or any other
protection, in direct contact with the hot enamel, risk melting and
deteriorating the enamel of the insides.
WARNING: Never remove the oven door seal.
CAUTION: Do not refill the cavity bottom with water during cooking
or when the oven is hot.
No additional operation/setting is required in order to operate the
appliance at the rated frequencies.
.WARNING: before initiating the automatic cleaning cycle:
- Clean the oven door;
- Remove large or coarse food residues from the inside of the oven
using a damp sponge. Do not use detergents;
- Remove all accessories and the sliding rack kit (where present); -Do
not place tea towels.
• ln ovens with meat probe it is necessary, before making the
cleaning cycle, close the hole with the nut provided. Always close the
hole with the nut when the meat probe is not used.
During the pyrolytic cleaning process, surfaces can heat up more
than usual, children must therefore be kept at a safe distance.
EN 04
Summary
EN 05
General Instructions
6
1.1 Safety indications
1.2 Electrical safety
1.3 Recommendations
1.4 Installation
1.5 Waste management
1.6 Declaration of compliance
2.1 Overview
2.2 Accessories
2.3 First use
Product Description
8
3.1 Display description
3.2 Cooking modes
Use of the Oven
9
4.1 General notes on cleaning
4.2 Using the Steam Function
4.3 Maintenance
• Removal and cleaning of the side
racks
• Removal of the oven window
• Removal and cleaning of the glass
door
• Changing the bulb
Oven Cleaning and Maintenance
12
5.1 F.A.Q.
Troubleshooting
15
1. General Instructions
We thank you for choosing one of our products. For the
best results with your oven, you should read this
manual carefully and retain it for future reference.
Before installing the oven, take note of the serial
number so that you can give it to customer service staff
if any repairs are required. Having removed the oven
from its packaging, check that it has not been damaged
during transportation. If you have doubts, do not use
the oven and refer to a qualified technician for advice.
Keep all of the packaging material (plastic bags,
polystyrene, nails) out of the reach of children. When
the oven is switched on for the first time, strong
smelling smoke can develop, which is caused by the glue on the insulation panels surrounding the oven
heating for the first time. This is absolutely normal and, if it occurs, you should wait for the smoke to
dissipate before putting food in the oven. The manufacturer accepts no responsibility in cases where
the instructions contained in this document are not observed.
NOTE: the oven functions, properties and accessories cited in this manual will vary, depending on the
model you have purchased.
1.1 Safety Indications
Only use the oven for its intended purpose, that is only for the cooking of foods; any other use, for
example as a heat source, is considered improper and therefore dangerous. The manufacturer cannot
be held responsible for any damage resulting from improper, incorrect or unreasonable usage.
The use of any electrical appliance implies the observance of some fundamental rules:
- do not pull on the power cable to disconnect the plug from the socket;
- do not touch the appliance with wet or damp hands or feet;
- in general the use of adaptors, multiple sockets and extension cables is not recommended;
- in case of malfunction and/or poor operation, switch off the appliance and do not tamper with it.
1.2 Electrical Safety
ENSURE THAT AN ELECTRICIAN OR QUALIFIED TECHNICIAN MAKES THE ELECTRICAL CONNECTIONS.
The power supply to which the oven is connected must conform with the laws in force in the country of
installation. The manufacturer accepts no responsibility for any damage caused by the failure to observe
these instructions. The oven must be connected to an electrical supply with an earthed wall outlet or a
disconnector with multiple poles, depending on the laws in force in the country of installation. The
electrical supply should be protected with suitable fuses and the cables used must have a transverse
section that can ensure correct supply to the oven.
CONNECTION
The oven is supplied with a power cable that should only be connected to an electrical supply with 220-
240 Vac 50 Hz power between the phases or between the phase and neutral. Before the oven is
connected to the electrical supply, it is important to check:
- power voltage indicated on the gauge;
- the setting of the disconnector.
The grounding wire connected to the oven's earth terminal must be connected to the earth terminal of
the power supply.
WARNING
Before connecting the oven to the power supply, ask a qualified electrician to check the continuity of the
power supply's earth terminal. The manufacturer accepts no responsibility for any accidents or other
problems caused by failure to connect the oven to the earth terminal or by an earth connection that has
defective continuity.
EN 06
1.3 Recommendations
After each use of the oven, a minimum of cleaning will help keep the oven perfectly clean.
Do not line the oven walls with aluminium foil or single-use protection available from stores. Aluminium
foil or any other protection, in direct contact with the hot enamel, risks melting and deteriorating the
enamel of the insides. In order to prevent excessive dirtying of your oven and the resulting strong
smokey smells, we recommend not using the oven at very high temperature. It is better to extend the
cooking time and lower the temperature a little. In addition to the accessories supplied with the oven,
we advise you only use dishes and baking moulds resistant to very high temperatures.
1.4 Installation
The manufacturers have no obligation to carry this out. If the assistance of the manufacturer is required
to rectify faults arising from incorrect installation, this assistance is not covered by the guarantee. The
installation instructions for professionally qualified personnel must be followed. Incorrect installation
may cause harm or injury to people, animals or belongings. The manufacturer cannot be held
responsible for such harm or injury.
The oven can be located high in a column or under a worktop. Before fixing, you must ensure good
ventilation in the oven space to allow proper circulation of the fresh air required for cooling and
protecting the internal parts. Make the openings specified on last page according to the type of fitting.
NOTE: as the oven could require maintenance work, it is advisable to keep another wall socket available
so that the oven can be connected to this if it is removed from the space in which it is installed. The
power cable must only be substituted by technical service staff or by technicians with equivalent
qualifications.
1.5 Waste management and environmental protection
This appliance is labelled in accordance with European Directive 2012/19/EU regarding
electric and electronic appliances (WEEE). The WEEE contain both polluting substances
(that can have a negative effect on the environment) and base elements (that can be
reused). It is important that the WEEE undergo specific treatments to correctly remove and
dispose of the pollutants and recover all the materials. Individuals can play an important
role in ensuring that the WEEE do not become an environmental problem; it is essential to
follow a few basic rules:
- the WEEE should not be treated as domestic waste;
- the WEEE should be taken to dedicated collection areas managed by the town council or a registered
company.
In many countries, domestic collections may be available for large WEEEs. When you buy a new
appliance, the old one can be returned to the vendor who must accept it free of charge as a one-off, as
long as the appliance is of an equivalent type and has the same functions as the purchased appliance.
SAVING AND RESPECTING THE ENVIRONMENT
Where possible, avoid pre-heating the oven and always try to fill it. Open the oven door as infrequently
as possible, because heat from the cavity disperses every time it is opened. For a significant energy
saving, switch off the oven between 5 and 10 minutes before the planned end of the cooking time, and
use the residual heat that the oven continues to generate. Keep the seals clean and in order, to avoid any
heat dispersal outside of the cavity. If you have an electric contract with an hourly tariff, the "delayed
cooking" programme makes energy saving more simple, moving the cooking process to start at the
reduced tariff time slot.
EN 07
1.6 Declaration of compliance
By placing the mark on the appliance, we are confirming compliance to all relevant European
safety, health and environmental requirements which are applicable in legislation for this product.
2. Product Description
2.1 Overview
1. Control panel
2. Shelf positions
(lateral wire grid if included)
3. Metal grill
4. Drip pan
5. Fan (behind the steel plate)
6. Oven door
2.2 Accessories
Drip pan
1
Collects the residues that drip during the cooking
of foods on the grills.
Metal grill
2
Holds baking trays and plates.
EN 08
Lateral wire grids
3
It located at both sides of the oven cavity. It holds
metal grills and drip pans.
2
3
5
4
6
MENU
1
MENU
8
2.3 First Use
PRELIMINARY CLEANING
Clean the oven before using for the first time. Wipe over external surfaces with a damp soft cloth. Wash
all accessories and wipe inside the oven with a solution of hot water and washing up liquid. Set the
empty oven to the maximum temperature and leave on for about 1 hour, this will remove any lingering
smells of newness.
EN 09
3. Use of the Oven
3.1 Display description
1. Minute minder
2. Clock setting
3. Cooking time
4. End of cooking
5. Temperature or clock display
6. LCD display adjustment controls
7. Thermostat selector knob
8. Function selector knob
WARNING : the first operation to carry out after the
oven has been installed or following the
interruption of power supply (this is recognizable
the display pulsating and showing 12:00 ) is setting
the correct time. This is achieved as follows.
•Push the central button.
•Set time with "-" "+" buttons.
•Release all buttons.
ATTENTION: The oven will only operate providing the
clock is set.
EN 10
FUNCTION HOW TO DEACTIVATE WHAT IT DOES WHY IT IS NEEDED HOW TO USE
KEY LOCK
MINUTE
MINDER
COOKING
TIME
END OF
COOKING
•Child Lock function is
activated by touching Set
(+) for a minimum of 5
se con ds . F rom th is
moment on all other
function are locked and
the display will flash
STOP and preset time
intermittently.
•Child Lock function is
deactivated by touching
touchpad Set (+) again for
a minimum of 5 seconds.
From this moment on all
functions are selectable
again.
•Push the central button
1 times
•Press the buttons "-"
"+"
to set the required time
•Release all the buttons
•When the set time as
elaps e d an audi b l e
alarm is activated (this
alarm will stop on its
own, however it can be
stopped immediately by
pressing the button)
SELECT.
•Sounds an alarm at the
end of the set time.
During the process, the
display shows the
remaining time.
•Allows to use the oven as
alarm clock ( c o u ld b e
a c t i v a t e d e i t h er w i t h
operating the oven or with
out operating the oven)
Push the central button
2 times
Press the buttons "-" or
"+"to set the lenght of
cooking required
Release all buttons
S e t t h e c o o k i n g
function with the oven
function selector
It allows to preset the
cooking time required for
the recipe chosen.
To check how long is left
to run press the SELECT
button 2 Times.
To alter/change the
preset time press SELECT
and "-" "+" buttons.
Push any button to
stop the signal. Push the
central button to return
t o t h e c l o c k
function.
•When the time is elapsed
the oven will switch off
automatically.
Should you wish to stop
cooking earlier either turn
the function selector to 0, or
s e t t i m e t o 0 : 0 0
(SELECT and "-" "+" buttons)
•At the time set, the
oven will switch off. To
switch off manually,
turn the oven function
selector to position O.
•Enables you to set the
end of cooking time
To check the preset
time push the central
button 3 times
•To modify the preset
ti m e p ress bu t t o ns
SELECT + "-" "+"
Push the central button
3 ti me s Pre ss t h e
buttons "-" "+" to set the
time at which you wish
the oven to switch off
•Release the buttons
• S e t t h e c o o k i n g
function with the oven
function selector.
•This function is typically
used with “cooking time
function.
For example if the dish has
to be cooked for 45 minutes
and needs to be ready by
12:30, simply select the
required function, set the
cooking time to 45 minutes
and the end of cooking time
to 12:30.
•At the end of the cooking
set time, the oven will
switch off automatically and
an audible alarm will ring.
• C o o k i n g w i l l s t a r t
automat ically at 1 1:45
(12:30 minus 45 mins) and
will continue until the pre-
set end-of-cooking-time,
when the oven will switch
itself off automatically.
WARNING.
If the END of cooking is
selected without setting the
length of cooking time, the
oven will start cooking
immediately and it will stop
at the END of cooking time
set.
T °C
default
L3
T °C
range
L1 ÷ L5
Function
Dial
Function (Depends on the oven model)
LAMP: Turns on the oven light.
GRILL: use the grill with the door closed.
The top heating element is used alone and you can adjust the temperature. Five
minutes preheating is required to get the elements red-hot. Success is guaranteed
for grills, kebabs and gratin dishes. White meats should be put at a distance from the
grill; the cooking time is longer, but the meat will be tastier. You can put red meats
and fish fillets on the shelf with the drip tray underneath. The oven has two grill
positions:
Grill: 2140 W Barbecue: 3340 W
DEFROST: When the dial is set to this position. The fan circulates air at room
temperature around the frozen food so that it defrosts in a few minutes
without the protein content of the food being changed or altered.
*Tested in accordance with the CENELEC EN 60350-1 used for definition of energy class.
210 50 ÷ 240
3.2 Cooking Modes
EN 11
220 50 ÷ 280
CONVENTIONAL + STEAM: Both top and bottom heating elements will be
switched on using the water inside the cavity to generate steam. It is
necessary to add 150 ml of water in the cavity and rotate the knob to this
homogeneous cooking performance.
PIZZA: With this function hot air circulated in the oven to ensure perfect result
for dishes such as pizza or cake.
220 50 ÷ 230
BOTTOM HEATING + FAN + STEAM: The bottom heating element is used with
the fan circulating the air inside the oven. For the steam generation, it is
necessary to add 150 ml of water in the cavity and rotate the knob to this
function. The steam option together with the bottom heating and the fan,
ensures a perfect leavening and cooking to bread.
MASTER BAKE: This function allows to cook in a healthier way, by reducing the
amount of fat or oil required. The combination of heating elements with a
pulsating cycle of air ensures a perfect baking result.
150 50 ÷ 240
CONVENTION + FAN + STEAM: Selecting this function, the lower and upper
heating elements work together with the fan for a uniform cooking on all
levels. It is necessary to add 150 ml of water in the cavity and rotate the knob to
this function. This cooking method enhances the tendemess and flavors of
each dısh, especially roasting and red meat.
210 50 ÷ 230
*
*
4. Oven cleaning and maintenance
4.1 General notes on cleaning
The lifecycle of the appliance can be extended through regular cleaning. Wait for the oven to cool before
carrying out manual cleaning operations. Never use abrasive detergents, steel wool or sharp objects for
cleaning, so as to not irreparably damage the enamelled parts. Use only water, soap or bleach-based
detergents (ammonia).
GLASS PARTS
It is advisable to clean the glass window with absorbent kitchen towel after every use of the oven. To
remove more obstinate stains, you can use a detergent-soaked sponge, well wrung out, and then rinse
with water.
OVEN WINDOW SEAL
If dirty, the seal can be cleaned with a slightly damp sponge.
ACCESSORIES
Clean accessories with a wet, soapy sponge before rinsing and drying them: avoid using abrasive
detergents.
DRIP PAN
After using the grill, remove the pan from the oven. Pour the hot fat into a container and wash the pan in
hot water, using a sponge and washing-up liquid.
If greasy residues remain, immerse the pan in water and detergent. Alternatively, you can wash the pan
in the dishwasher or use a commercial oven detergent. Never put a dirty pan back into the oven.
EN 12
4.2 Using the Steam Function
Steam function allows having better humidity during cooking cycle. We recommend alternating steam
cooking with traditional cooking.
Please follow the steps below in order to use correctly this function.
1- Open the oven door
2- Fill the cavity bottom only when the oven is cold, using max 150ml water.
3- Insert food in the cavity and close the oven door.
4- Set the function you prefer to cook with steam.
5- Turn the temperature knob to select temperature.
6- To turn the appliance off switch the function and temperature knobs to zero position
7- Remove residual water from the bottom of the cavity after the oven cooled down.
8- Clean drip tray after every cooking cycle. Please see chapter 4.1 for cleaning instructions.
• WARNING: When filling in the water tank the level of the water must not exceed the maximum level
indicated on the tank
• WARNING: Risk of burn and damage to the appliance: using the steam function released steam can
cause burns: Open the door carefully to avoid injury after using a cooking function with steam.
INSTRUCTION FOR REMOVAL AND CLEANING OF THE SIDE RACKS
1. Remove the wire racks by pulling them in the direction of the arrows (see below)
2. To clean the wire racks either put them in the dishwasher or use a wet sponge, ensuring that they are
dried afterwards.
3. After the cleaning process install the wire racks in reverse order.
REMOVAL OF THE OVEN WINDOW
1. Open the front window.
2. Open the clamps of the hinge housing on the right and left side of the front window by pushing them
downwards.
3. Replace the window by carrying out the procedure in reverse.
4.3 Maintenance
EN 13
LOW-E
1
2
3
1.
2.
3.
4.
5.
6.
7.
REMOVAL AND CLEANING OF THE GLASS DOOR
1. Open the oven door.
2.3.4. Lock the hinges, remove the screws and remove the upper metal cover by pulling it upwards.
5.6. Remove the glass, carefully extracting it from the oven door (NB: in pyrolytic ovens, also remove
the second and third glass (if present)).
7. At the end of cleaning or substitution, reassemble the parts in reverse order.
On all glass, the indication "Low-E" must be legible and positioned on the left side of the door, close to
the left-hand lateral hinge. In this way, the printed label of the first glass will be inside the door.
EN 14
CHANGING THE BULB
1. Disconnect the oven from the mains supply.
2. Undo the glass cover, unscrew the bulb and replace it with a new bulb of the same type.
3. Once the defective bulb is replaced, replace the glass cover.
5. Troubleshooting
5.1 FAQ
PROBLEM POSSIBLE CAUSE SOLUTION
The oven does not heat up
The clock is not set Set the clock
A cooking function and
temperature has not been set
Ensure that the necessary
settings are correct
The oven does not heat up
EN 15
Steam and condensation on
the user interface panel
Clean with a microfiber
cloth the user interface
panel to remove the
condensation layer
No reaction of the touch
user interface
FR 16
Conseils De Securite
Lorsque vous ouvrez la porte après la cuisson, quelques gouttes d’eau
peuvent sortir de la porte. Cela dépend du type d’aliment que vous avez
cuisiné.
Pendant la cuisson, de l’humidité peut se condenser à l’intérieur de la
cavité ou sur la vitre de la porte. Il s’agit d’un phénomène normal. Pour
réduire cet effet, attendez 10-15 minutes après avoir allumé l’appareil
avant de mettre les aliments au four. La condensation disparaîtra de
toutes façons dès que le four aura atteint la température de cuisson.
• Cuisez les légumes dans un récipient avec couvercle plutôt que dans
un ustensile ouvert.
Évitez de laisser des aliments à l’intérieur du four plus de 15-20
minutes après cuisson.
• AVERTISSEMENT : Lappareil et ses parties accessibles chauffent
pendant l’utilisation.
Faites attention à ne pas toucher les parties chaudes.
AVERTISSEMENT : Les parties accessibles peuvent devenir très
chaudes quand le grill est en marche. Les enfants doivent être tenus à
une distance de sécurité.
AVERTISSEMENT : Vérifiez que l’appareil est éteint avant de remplacer
l’ampoule, pour éviter le risque de chocs électriques.
AVERTISSEMENT : Afin d’éviter tout risque lié à la réinitialisation
accidentelle de l’interrupteur thermique, l’appareil ne doit pas être
alimen par un dispositif de commutation externe, tel qu’une
minuterie, ou relié à un circuit régulièrement allumé et éteint.
Les enfants de moins de 8 ans doivent rester à une distance de
sécurité de l’appareil s’ils ne sont pas surveillés en permanence.
Les enfants ne doivent pas jouer avec l’appareil.
Lappareil peut être utilisé par des enfants de plus de 8 ans et par des
personnes dont les capacités physiques, sensorielles ou mentales sont
limitées, sans expérience ni connaissance du produit, uniquement s’ils
sont surveillés ou s’ils ont été informés de la manière d’utiliser
l’appareil, en toute sécurité et qu’ils comprennent les risques possibles.
Le nettoyage et l’entretien ne doivent pas être effectués par des
FR 17
enfants sans surveillance.
N’utilisez pas de matériaux rugueux ou abrasifs ou de racloirs
métalliques acérés pour nettoyer les vitres des portes des fours, car cela
pourrait rayer la surface et provoquer la rupture de la vitre.
Coupez le four avant de retirer les pièces amovibles.
Après le nettoyage, remontez-les selon les instructions.
Utilisez uniquement la sonde à viande recommandée pour ce four.
N’utilisez pas un nettoyeur à vapeur pour le nettoyage.
Branchez le câble d’alimentation sur une prise de courant qui
supporte le voltage (le courant et la charge sont indiqués sur l’étiquette)
et vérifiez la présence d’une mise à la terre. La prise d’alimentation doit
supporter la charge indiquée sur l’étiquette et être dotée d’une mise à
la terre en état de fonctionnement. Le conducteur de mise à la terre est
jaune et vert. Cette opération doit être exécutée par le personnel
qualifié. En cas d’incompatibilité entre la prise d’alimentation et la fiche
du câble de l’appareil, demandez à un électricien professionnel de
remplacer la prise d’alimentation par un dispositif compatible.
La fiche du câble d’alimentation et la prise d’alimentation doivent être
conformes aux normes en vigueur dans le pays d’installation.
Il est possible de brancher l’appareil à la prise d’alimentation en
installant entre l’appareil et la prise d’alimentation un disjoncteur
multipolaire qui supporte la charge électrique maximale,
conformément aux lois en vigueur.
Le conducteur jaune et vert de mise à la terre ne doit pas être bloqué
par le disjoncteur. La prise d’alimentation ou le disjoncteur multipolaire
utilisé pour le branchement doit rester à tout moment accessible après
installation de l’appareil.
Le débranchement doit se faire à l’aide soit de la prise d’alimentation,
soit dun interrupteur installé sur le circuit électrique fixe,
conformément aux normes électriques.
Si le câble d’alimentation est endommagé, il doit être remplacé par un
câble ou un faisceau de câbles spécial disponible auprès du fabricant ou
du service après-vente.
FR 18
Le câble d’alimentation requis est le H05V2V2-F.
Cette opération doit être exécutée par le personnel qualifié. Le
conducteur de mise à la terre (jaune et vert) doit être environ 10 mm
plus long que les autres conducteurs. Pour toutes parations,
contactez le service après-vente en insistant sur l’utilisation de pièces
de rechange d’origine.
Le non-respect des consignes ci-dessus peut compromettre la
sécurité de l’appareil et annuler la garantie.
Éliminez les éclaboussures importantes avant de proder au
nettoyage.
Une coupure de courant prolongée durant une phase de cuisson peut
engendrer un dysfonctionnement de l’écran. Dans ce cas, veuillez
contacter le service après-vente.
Lappareil ne doit pas être installé derrière une porte décorative, pour
éviter la surchauffe.
Pour introduire la grille dans le four, vérifiez que le butoir est dirigé
vers le haut et au fond de la cavité. La grille doit être complètement
insérée dans la cavité.
AVERTISSEMENT : Ne recouvrez pas les parois du four avec du papier
aluminium ou une protection jetable disponible dans les magasins. Le
papier d’aluminium ou toute autre protection, en contact direct avec
l’émail chaud, risque de fondre et de détériorer l’émail de la cavité
intérieure.
AVERTISSEMENT : N’enlevez jamais le joint de la porte du four.
PRUDENCE : Ne remplissez pas le fond de la cavité avec de l’eau
pendant la cuisson ou lorsque le four est chaud.
Aucune autre opération ni aucun autre réglage ne sont requis pour
faire fonctionner l’appareil aux fréquences nominales.
FR 19
SOMMAIRE
Instructions Générales
20
1.1 Indications de sécurité
1.2 Sécurité électrique
1.3 Recommandations
1.4 Installation
1.5 La gestion des déchets et la
protection de l'environnement
1.6 Déclaration de conformité
2.1 Vue d'ensemble
2.2 Accessoires
2.3 Première utilisation
Description du produit
22
3.1 Description de l'affichage
3.2 Mode de cuisson
Utilisation du Four
23
4.1 Remarques générales concernant le
nettoyage
4.2 Utilisation de la fonction Steam
4.3 Entretien
• Retrait et nettoyage des grilles
latérales
• Retrait de la porte du four
• Retrait et nettoyage des vitres
• Remplacement de l'ampoule
Nettoyage du four et
maintenance
26
5.1 F.A.Q.
Dépannage
29
FR 20
1. Instructions générales
Nous vous remercions d'avoir choisi un de nos produits.
Pour obtenir les meilleurs résultats avec votre four, vous
devez lire attentivement ce manuel et le conserver pour
toute consultation ultérieure. Avant d'installer le four,
notez le numéro de série, il vous sera demandé par le
support technique si des réparations sont nécessaires.
Après avoir enlevé le four de son emballage, vérifiez
qu'il n'a pas été endommagé pendant le transport. Si
vous avez des doutes, ne pas utiliser le four et se référer
à un technicien qualifié pour obtenir des conseils.
Conservez tous les matériaux d'emballage (sacs en
plastique, polystyrène, clous) hors de la portée des
enfants.Lors de la première utilisation du four, il peut se produire un dégagement de fumée âcre
provoqué par le premier échauffement de la colle des panneaux d’isolation enveloppant le four. Ce
phénomène est normal. Attendez que la fumée cesse avant de cuire des aliments. Le fabricant décline
toute responsabilité dans les cas où les instructions contenues dans le présent document ne sont pas
respectées.
REMARQUE: les fonctions du four, les propriétés et les accessoires cités dans ce manuel peuvent varier
selon les modèles.
1.1 Indications de sécurité
Utilisez uniquement le four à sa destination, qui est seulement pour la cuisson des aliments; toute autre
utilisation, par exemple comme une source de chaleur, est considérée comme impropre et donc
dangereuse. Le fabricant ne peut être tenu responsable de tout dommage lié à une mauvaise utilisation
ou a des modifications techniques du produit.
L'utilisation de tout appareil électrique implique le respect de certaines règles fondamentales:
- Ne pas tirer sur le fil électrique pour débrancher la prise.
- Ne pas toucher l'appareil avec les mains ou les pieds mouillés ou humides;
- En général l'utilisation d'adaptateurs, de prises multiples et de rallonges est déconseillé;
- En cas de dysfonctionnement et / ou de mauvais fonctionnement, éteindre l'appareil et ne pas y
toucher.
1.2 Sécurité électrique
LE BRANCHEMENT ELECTRIQUE DOIT ÊTRE REALISE PAR UN INSTALLATEUR AGREE OU UN
TECHNICIEN DE E.QUALIFICATION SIMILAIR
L'alimentation électrique à laquelle le four est connecté doit être conforme aux lois en vigueur dans le
pays d'installation. Le fabricant décline toute responsabilité pour tout dommage causé par le non
respect de ces instructions. Le four doit être raccorà l'alimentation électrique avec une prise murale
reliée à la terre ou par l'intermédiaire d'un dispositif à coupure omnipolaire, selon les lois en vigueur
dans le pays d'installation. L'alimentation électrique doit être protégée par des fusibles appropriés et les
câbles utilisés doivent avoir une section transversale qui peut assurer une alimentation normale du four.
CONNEXION
Le four est livré avec un câble d’alimentation permettant le raccordement sous une tension électrique
de 230 V entre les phases ou entre phase et neutre. Le raccordement devra être effectué après avoir
vérifié:
- La tension d'alimentation indiquée sur le compteur;
- Le réglage du disjoncteur.
Le fil de protection du cordon (vert/jaune) relié à la Borne Terre de l’appareil doit être relié à la Borne
Terre de l’installation.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30

ROSIERES RFC3CS3259IN User manual

Category
Ovens
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages