2. Iveco
  3. KIT-6IDVII Daily VII Double DIN Facia Plate

Iveco KIT-6IDVII Daily VII Double DIN Facia Plate User manual

  • Hello! I've reviewed the installation manual for the IVECO Daily VII radio unit. This document provides detailed instructions on how to install the new unit, covering topics from removing the old equipment to configuring the new wiring harness, including steering wheel remote controls. I'm ready to answer your questions about the installation process and the device's features.
  • What should be connected first to prevent ESD damage?
    What should be done if audio comes from the wrong speakers?
    What is the purpose of the S1 and S2 connectors?
1
14. Connectivity Layout
8
INSTALLATION MANUAL
IVECO
Model: Daily VII
Year: > 2019
Kit content: double DIN facia plate; mounting
brackets + screws; SWRC CAN bus & LIN bus
wiring harness; antenna adapters; camera
adapter; USB/AUX adapter; speaker adapter
32
Content and wiring harness connections
1 - to RADIO connector
2 - to CAR connector
3 - POWER ANTENNA output
4 - REMOTE output
5 - to LIN BUS - to Brown cable
(point 7 page 4-5)
6 - to LIN BUS - to White cable
(point 7 page 4-5)
7 - SPEED output (Green) →to
SPEED input of Head Unit
11 - Configuration setting S1/S2
(point 7 / page 4-5)
9 - for future reference:
Black –GROUND
Yellow –POWER 12V+
Red –ACC (IGNITION)
10 - to WIRED SWRC REM Socket
11 - Speaker connection (point 9 / page 6)
12 - CAN BUS access (point 7 / page 4-5)
13 - FAKRA antenna adapter
14 - ISO/DIN antenna adapter
15- USB/AUX adapter
OPTIONAL 1 →C1 (point 7 / page 4-5)
OPTIONAL 2 →(point 9 / page 6)
1. This is how the original dashboard looks
like.
2. Remove the drawer and unscrew the
two screws as shown in the picture.
3. Remove the rubber compartment as
shown in the picture.
4. Unscrew the central screw and remove
the original facia.
5
6
4
7
9
13
10
Optional 1
Optional 2
1
3
2
11
12
14 15
8
5. In order to fit the radio unit some plastic
parts need to be cut and removed. The
parts to be removed are the four flaps
and the plastic rectangular central
protrusion highlighted in the pictures.
6. Connect the harness as indicated on left
side (page 2).
ATTENTION!
In order to prevent ESD damage, the STEERING WHEEL REMOTE JACK (10)
must be connected before plugging in the connectors on car side.
CONFIGURATION STEP 1 STEP 2
Configuration without radio steering wheel
controls and open dash
C2 and C3 connected. S1 and S2 not connected.
Configuration with radio steering wheel
controls and open dash
Remove the tape and connect the Brown and
thin White cable to cable (5&6) (see page 2)
of the interface harness.
C1 and C3
connected. –S1 and S2 not
connected.
Configuration with radio steering wheel
controls and DAB radio
C2 and C3 connected. S1 and S2 connected.
Configuration with radio steering wheel
controls and HI-CONNECT radio
Not compatible with Daily VII and HI-CONNECT
radio
7. Set the harness according to the configuration of your vehicle.
5
Iveco Daily VII steering wheel remote controls functions.
8. Steering wheel remote controls functions.
1- Volume +
2- Mute
3- Volume -
4- Seek +
5- Source
6- Seek –
7- Accepting
incoming call
8- Voice
9
6
78
1
2
3
4
5
6
7
9. Pair your phone and make a call.
If you hear the audio from WRONG SPEAKERS →install OPTIONAL 2
(see page 2 point 11).
10. Take the left and right brackets and fix
them with the supplied screws as shown
in the picture.
Connect the harness as indicated on
page 2.
11. Make all connections, check the proper
functioning of the whole system and fix
the head unit with the OEM screws as
shown in the picture.
12. Fix the metal bracket with the supplied
screw as shown.
13. Mount the facia plate on the dashboard.
This is the final result.
/