Moldex 4040 User guide

Type
User guide

Moldex 4040 is a versatile cleaning solution designed to remove tough stains caused by mold, mildew, algae, and moss from a wide range of surfaces, leaving them completely clean. It is ideal for exterior cleaning tasks and can be used on various materials, including wood, vinyl, aluminum siding, roofing, gutters, stucco, brick, cement blocks, masonry, walkways, and walls. With its concentrated formula, one bottle of Moldex 4040 can make up to 11 gallons of premix when mixed with water (1:10 ratio), allowing you to cover up to 2000 square feet.

Moldex 4040 is a versatile cleaning solution designed to remove tough stains caused by mold, mildew, algae, and moss from a wide range of surfaces, leaving them completely clean. It is ideal for exterior cleaning tasks and can be used on various materials, including wood, vinyl, aluminum siding, roofing, gutters, stucco, brick, cement blocks, masonry, walkways, and walls. With its concentrated formula, one bottle of Moldex 4040 can make up to 11 gallons of premix when mixed with water (1:10 ratio), allowing you to cover up to 2000 square feet.

REV: 1/14
CAUTION: MAY IRRITATE EYES. MAY IRRITATE SKIN.
Do not mix with other chemicals. Do not get in eyes. Do not get on skin or clothing. Do not breathe
fumes. KEEP OUT OF REACH OF CHILDREN
FIRST AID:
Contains: Sodium metasilicate, Lauryldimethylamine oxide.
If swallowed, call a Poison Control Center or doctor immediately. Do not induce vomiting. If in eyes,
rinse with water for 15 minutes. If on skin, rinse well with water
.
When mixed (1:10) with water, one bottle of concentrate makes 11 GALLONS of premix, and cleans up
to 2000 sq. ft. (less on rougher surfaces), and can be applied by pressure washer, pump-up sprayer,
brush or roller. Contains anti-corrosive agents to safeguard pressure washer parts (bleach can erode
O-rings).
DIRECTIONS FOR USE:
(MANUAL USE DIRECTIONS)
Wear appropriate protective apparel
when handling concentrate (face
protection, rubber gloves, and/or apron).
1. Mix at 1:10 parts concentrate with water.
2. Fill spray bottles, buckets, or pump
sprayers and spray to wet the area to be
cleaned. Work in manageable sections if
cleaning a large area.
3. Wait several minutes to allow cleaner to
work before wiping, scrubbing or mopping
the surface clean.
4. Rinse with clean water, allow surfaces to
dry before resuming use or traffic.
IMPORTANT: Read entire label before use • When using a pressure washer to clean painted surfaces,
please be aware that water pressure alone may remove paint, or highlight existing discoloration caused
by the sun's UV rays. • With a garden hose, rinse any nearby plants with clean water. • Always test on an
inconspicuous area first. • Any overspray can be neutralized with large volumes of water. • On extremely
soiled or mildewed surfaces it may be necessary to scrub with a bristle brush, and a second application
may be needed. Mildew stains may not be completely removed from porous surfaces. • In case of severe
oil and grease stains on porous surfaces, oil may bleed to the surface or leave a residual stain. Repeat
applications may lighten stains, but not remove completely.
• Won’t Harm
Shrubs
• No Bleach
Moldex
®
POWER! contains unique
properties that remove tough stains
caused by mold, mildew, algae, and moss
leaving surfaces completely clean.
SAFE, FAST, and EFFECTIVE!
Moldex
®
POWER! contains unique
properties that remove tough stains
caused by mold, mildew, algae, and moss
leaving surfaces completely clean.
SAFE, FAST, and EFFECTIVE!
(PRESSURE WASHER APPLICATION)
1. Rinse surrounding plants with water, before and after
application*.
2. Wet surface to be cleaned, prior to applying the product.
3. Place detergent application siphon tube and screen filter
directly into container. Open meter valve (if applicable)
for maximum product flow. For reservoir machines, pour
product (full strength) into pressure washer.
4. Spray at low pressure onto a wet surface.
5. On vertical surfaces, always spray from the top down.
6. Allow product to remain on the surface for 3 to 5
minutes to penetrate. Do not allow product to dry on
surface.
7. Remove siphon tube from solution and rinse surface
with high pressure water spray thoroughly.
8. Flush siphon tube with clean water prior to storage.
Recommended For:
Exterior siding (wood, vinyl, aluminum), roofing of all types
(asphalt shingles, fiberglass shingles, cedar, tile), gutters, stucco, brick
and cement blocks, masonry, walkways and walls.
Exterior
Siding
Driveways
& Walkways
Boats &
RVs
Cement
& Brick
Patio
Furniture
Decks &
Fences
Awnings &
Fabrics
General
Cleaner
IDEAL FOR MOST SURFACES:
CAUTION: MAY IRRITATE EYES & SKIN:
See side panel for additional statements.
KEEP OUT OF REACH OF CHILDREN.
NET CONTENTS: 1 GALLON (128 FL. OZ.) (3.8L) Made in USA
183325 00054 9
EnviroCare Corporation
Wilmington, MA. 01887
Toll-Free: 1-877-463-2628
www.envirocarecorp.com
Concentrated
Power Wash Compatible
Decks
Roof
Siding Cement
Cleans Mold,
Mildew & Algae Stains.
Removes Dirt & Grime.
11
Ready to use
GALLONS
Makes
LABEL
SIZE: 5” X 12.875”
DIELINE
OUTSIDE BOTTLE
ARTWORK
BOTTLE ARTWORK
1 GALLON POWER!
  • Page 1 1

Moldex 4040 User guide

Type
User guide

Moldex 4040 is a versatile cleaning solution designed to remove tough stains caused by mold, mildew, algae, and moss from a wide range of surfaces, leaving them completely clean. It is ideal for exterior cleaning tasks and can be used on various materials, including wood, vinyl, aluminum siding, roofing, gutters, stucco, brick, cement blocks, masonry, walkways, and walls. With its concentrated formula, one bottle of Moldex 4040 can make up to 11 gallons of premix when mixed with water (1:10 ratio), allowing you to cover up to 2000 square feet.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI