KRAFTWERK 32106 Operating instructions
- Category
- Cordless screwdrivers
- Type
- Operating instructions
KRAFTWERK 32106 is a cordless bit driver with a 7.2 V Li-Ion battery. The battery has a capacity of 1300 mAh and can be fully charged in 3 hours. The bit driver has a torque selector with 10 settings, which allows you to adjust the torque to the specific screw size and material. The bit driver also has a LED lamp, which can be used to illuminate the work area in poor lighting conditions. The bit driver comes with a charging cable and a battery charger.
KRAFTWERK 32106 is a cordless bit driver with a 7.2 V Li-Ion battery. The battery has a capacity of 1300 mAh and can be fully charged in 3 hours. The bit driver has a torque selector with 10 settings, which allows you to adjust the torque to the specific screw size and material. The bit driver also has a LED lamp, which can be used to illuminate the work area in poor lighting conditions. The bit driver comes with a charging cable and a battery charger.
DO NOT attempt to operate the tool until you have read and
understood all instructions and safety rules contained in this
manual. Failure to comply may result in accidents involving fire,
electric shock, or serious personal injury. Save this owner’s
manual for future reference and review it frequently for safe
operation.
Art. 32106
Instruction Manual
Cordless bit driver 7.2 V
EN
3 h
Li-Ion
7.2 V
1300 mAh
10 570
g
0-230
1 min.
1/4"
WARNING:
2
3
4
5
6
7
8.1 Charging the battery (Fig. 1)
The battery is protected from exhaustive
discharge.
1. Bit chuck
2. Torque selector
3. On/O switch
4. Clockwise/Counter-clockwise selector switch
5. Lamp
6. Charging socket
7. Battery capacity indicator
8. Battery charger
9. Charging cable
8
An integrated protective circuit automatically
switches o the equipment when the battery is
at. In this case the bit chuck will cease to turn.
Warning! Do not press the ON/OFF switch any
more if the protective circuit has actuated. This
may damage the battery.
1. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Plug the battery charger in the plug
socket and connect the charging cable (9) to the
charging socket (6).
2. LED indications (7):
red LED illuminate: beginning charging process
yellow and red LED illuminate: battery is partly
charged all LEDs illuminate: battery is fully
charged.
If the battery pack fails to charge, please check
· whether there is voltage at the socket-outlet
· and check for proper contact with the charging
contacts in the battery charger.
If the battery still fails to charge, send
· the battery charger
· and the screwdriver
to our customer services department.
Timely recharging of the battery pack will help it
serve you well for a long time. You must recharge
the battery pack when you notice that the power
of the screwdriver drops.
Never allow the battery pack to become fully
discharged. This will cause it to develop a defect.
8.2 Changeover switch (Fig. 2/Item 4)
The slide switch above the ON/OFF switch is for
setting the direction of rotation of the cordless
screwdriver and for preventing the cordless
screwdriver from being switched on
inadvertently.
You can select between clockwise and
counterclockwise rotation. Change the direction
of rotation only when the equipment is at a
standstill. If you fail to observe this point, the
gearing may become damaged. When the slide
switch is in the middle position, the ON/OFF
switch is blocked.
8.3 ON/OFF switch (Fig. 2 / Item 3)
Press the On/O switch to switch the cordless
screwdriver on. Release the ON/OFF switch to
switch o the tool.
8.4 LED lamp
The LED lamp (5) can be used in poor lighting
conditions to illuminate the area where you want
to screw.
8.5 Torque setting (Fig. 3)
The cordless screwdriver is tted with a
mechanical torque selector.
The torque for a specic size of screw is selected
with the torque selector (2). The correct torque
depends on several factors:
· on the type and hardness of material in question
· on the type and length screws used
· on the requirements needing to be met by the
screwed joint.
The clutch disengages with a grating sound to
indicate when the set torque is reached.
8.6 Battery capacity indicator (Fig. 4)
The battery capacity indicator (7) indicates the
charge state of the battery on 3 colored LEDs.
All LEDs illuminate:
The battery is fully charged.
The yellow and red LED illuminate:
The battery has an adequate remaining charge.
Red LED:
The battery is empty, recharge the battery.
9
9. Technical data
8.7 Changing the tool (Fig. 5)
Important! Set the changeover switch to its
centre position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the cordless screwdriver.
· Insert the bit (a) into the bit chuck (1).
· Check that it is secure by attempting to pull the
tool apart again.
8.8 Screwdriving
We recommend using self-centering screws (e.g.
Torx screws, recessed head screws) designed for
reliable working. Be sure to use a bit that matches
the screw in shape and size. Set the torque, as
described elsewhere in these operating
instructions, to suit the size of screw.
10. Cleaning and maintenance
Always pull out the mains power plug before
starting any cleaning work.
10.1 Cleaning
• Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
• We recommend that you clean the device
immediately each time you have nished using it.
• Clean the equipment regularly with a moist
cloth and some soft soap. Do not use cleaning
agents or solvents; these could attack the plastic
parts of the equipment. Ensure that no water can
seep into the device.
10.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
11. Repairs
Only use accessories and spare parts
recommended by the manufacturer.
If the equipment should fail some day in spite of
our quality controls and your maintenance, only
have it repaired by an authorized electrician.
0-230 min-1
10
11
DECLARATION OF CONFORMITY
Model: 32106
LI-ION 60 MIN. FAST CHARGER 18 V
KRAFTWERK Sàrl,
25 rue due Stade, F-67870 Bischoffsheim
Declares under sole responsibility that the product to which this declaration relates is in
conformity with the following standard(s) or other normative document(s):
Following the provisions of Directive(s)
Machinery Directive:
Bischoffsheim, 06/09/2017 Alexander Pieper
CEO
2014/30/EU
2006/42/EC
2014/35/EU
EN 55014-1: 2006+A1/2009+A2/2011
EN 55014-2: 1997+A1/2001+A2/2008
EN 60745-1: 2009+A11/2010
EN 60745-2-2: 2010
EN 60335-1: 2012+A11/2014
EN 60335-2-29: 2004+A2/2010
EN 62233: 2008
WARRANTY
We do not take responsibility for any damage caused by misuse or any use that is not in
compliance with the safety standards described herein.
CUSTOMER SERVICES
Contact your local importer of your specialized dealer to obtain address of our service
department.
FROM DATE OF PURCHASE RECEIPT
2 YEAR GUARANTEE
ON MATERIAL OR PRODUCTION DEFECTS
www.kraftwerktools.com
KRAFTWERK Europe AG
Mettlenbachstrasse 23
CH-8617 Mönchaltorf
Switzerland
Tel. +41-44 949 40 50
KRAFTWERK Sàrl.
25, rue du Stade
F – 67870 Bischoffsheim
France
Tel. +33-388 48 64 50
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
KRAFTWERK 32106 Operating instructions
- Category
- Cordless screwdrivers
- Type
- Operating instructions
KRAFTWERK 32106 is a cordless bit driver with a 7.2 V Li-Ion battery. The battery has a capacity of 1300 mAh and can be fully charged in 3 hours. The bit driver has a torque selector with 10 settings, which allows you to adjust the torque to the specific screw size and material. The bit driver also has a LED lamp, which can be used to illuminate the work area in poor lighting conditions. The bit driver comes with a charging cable and a battery charger.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
KRAFTWERK 32109 Operating instructions
-
-
-
-
-
-
-
Other documents
-
Ronix 8536 User manual
-
Parkside 6 Li Operation and Safety Notes
-
EINHELL BT-CD 24 I Owner's manual
-
ALDI WCHD 14.4-2 User manual
-
Workzone WB 20 User manual
-
EINHELL TE-CD 18/44 Li-i; EX; UK User manual
-
EINHELL Expert TE-TK 12 Li; EX; UK User manual
-
-
-