Randall UNION Lockstitch User manual

Brand: Randall

Model: UNION Lockstitch

Type: User manual

Randall UNION Lockstitch is a straight needle and awl sewing machine for stitching heavy materials. It can sew a row of stitching 12 inches from the edge of any material and has a maximum speed of 800 stitches per minute. The machine can handle all thicknesses of leather and other materials up to ¾ inch. It is used by leading manufacturers for stitching footballs, basketballs, volleyballs, and softballs.

INSTRUCTION MANUAL

FOR THE

UNION

NeedLe ANd AwL - LOCk-STITCh - SewINg MAChINe

Serial Number: _______________

Manufactured by:

Randall Leather Machinery Company

401 Irvine Street ~ Yoakum, Texas 77995 USA

1-800-327-9420 or 1-361-293-7015

www.campbell-randall.com

CATALOg TABLe OF CONTeNTS

geNeRAL INFORMATION

DESCRIPTION....................................................................................................................... 1

CHARACTERSISTCS..............................................................................................................1

APPLICATIONS...................................................................................................................... 1

GENERAL ADVISE................................................................................................................. 1

DIRECTION OF OPERATION................................................................................................ 1

MACHINE INSTALLATION..................................................................................................... 2

SEWING THREAD................................................................................................................. 4

NEEDLES & AWLS................................................................................................................. 4

THREADING THE MACHINE................................................................................................. 5

THREAD LUBRICANT & WAX............................................................................................... 6

BOBBIN SETUP...................................................................................................................... 6

COMMENCE SEWING........................................................................................................... 7

ADJUSTMENTS & SERVICING

COMMON ADJUSTMENTS.................................................................................................... 8

OILING & CLEANING............................................................................................................. 8

PRESSER-FOOT ADJUSTMENT........................................................................................... 9

THREAD LOCK.................................................................................................................... 10

THREAD TENSION.............................................................................................................. 10

STITCH LENGTH................................................................................................................. 10

THREAD GUIDE ADJUSTMENT.......................................................................................... 11

LOOPER CAM ADJUSTMENT.............................................................................................. 11

NEEDLE & AWL ALIGNMENT.............................................................................................. 12

SHUTTLE TIMING (FINE)..................................................................................................... 13

TROUBLe ShOOTINg

TROUBLE SHOOTING......................................................................................................... 13

PARTS ChARTS

APPeNdIX

PARTS RECORD.................................................................................................................... A

LUBRICATION AND SERVICE RECORD...............................................................................B

NOTES................................................................................................................................... C

Since 1858

Technical Support

1-800-327-9420

Randall UnIOn lOck-stItc h

Table of Contents

Since 1858

www.Campbell-Randall.com

Randall UnIOn lOck -s t I tc h

General Information

Description

The UNION Lock-Stitch Sewing Machine is a straight needle

and awl sewing machine for stitching heavy materials.

Characteristics

• Feed: Needle Feed, Jump Foot.

• Speed: The maximum speed recommended for

the UNION is 800 stitches per minute. Maximum

speed is limited to the type of material being sewn.

It is recommended the machine run slower than

the maximum speed to insure operator control

and longevity of the machine. We cannot warranty

machines or parts that are damaged due to excessive

speed.

• Work Capacity: The machine operates on all

thickness of leather and other materials up to ¾ inch.

The throat of the machine is 12 inches, and can sew

a row of stitching 12 inches from the edge of any

material.

• Bobbin: The bobbin is extra large and carries 100 to

150 yards of thread, requiring few bobbin changes.

• Stitch Length: 4 to 12 stitched per inch

Applications

• Boot & Shoe Industry : fair stitching, moccasin seam or

any at sole work.

• Harness & Tack : for stitching all kinds of harness,

belting, and strap goods up to 3/4 inches thick.

• Sporting Goods : used by leading manufacturers for

stitching footballs, basket balls, volley balls, and soft balls.

It is noted for pulling a very tight seam.

General Advise

TO eNSURe PeRFeCT ACTION OF The MAChINe

• Do not operate the machine before lubricating it.

• Do not run the UNION in reverse. The machine hand wheel should

run counter-clockwise if you are facing the wheel.

• Use caution and give proper attention to the operation of your

machine when sewing

• Keep your hands away from the needle and awl when the power is

on and the machine is in operation

• Keep your hands away from all moving parts, nor place anything

close to them while operating the machine

• Do not make any adjustments or service the machine with the

power on.

• Do not run the machine with the presser foot resting on the needle

plate without material under the presser foot.

• Let the machine do its own feeding. Do not force material into or

way from the machine or you may bend or break a needle or awl.

• Do not crowd, retard or twist the work when sewing

• Do not run the machine with bobbin case and thread eye threaded

unless there is material under the presser foot.

• Have the machine in proper adjustment at all times

• Use good quality thread

• Keep your machine cleaned and well oiled

• Study this instruction book and become familiar with all parts of

your machine

• After receiving the machine, make sure all screws remain tight.

GENERAL INFORMATION

Please read this Instruction Manual carefully before using your machine in order to guarantee

reliable operation and a long life. Refer to this Manual often for questions and adjustments.

Direction Operation:

Always run the hand wheel toward the operator, that is to

turn the wheel counterclockwise if you are facing the wheel.

Never attempt to sew with the machine in reverse (clockwise)

rotation, or damage to the machine or material will result. The

UNION is not capable of sewing in reverse, but back stitching

can be done by lifting the foot and crossing over the previous

stitches.

Randall UnIOn lOc k -StItch

Installation

Randall UnIOn lOc k -StItch

Since 1858

Technical Support

1-800-327-9420

Machine Installation

Please insepect the packaging for any loose parts before discarding.

Motor Table

• Remove table from pallet and place in location

Machine Head

• Remove head from crating and place on table

• Secure the back of the machine with the included hook

bolts, and bolt the front of the machine head through the

table.

• Place the V-belt arounf the motor pulley, through the table

slot, and over the machine pulley. Ensure that the belt is

resting in the grooves of both pulleys, then tighten the belt

tension be lowering the motor with the adjustable motor

bracket. Lock the motor into postion with the bracket nuts

once the re tension is acheived.

Pedal Linkage

• Connect and adjust the right peddle linkage to the clutch

motor. Set the linkage with the center clamping bracket on

the rods.

• Connect the presser

foot cable from the

left pedal, through

the pulleys and up to

the connecting lever

behind the machine

hed. Secure with the

cable clamps.

Pulley Cover

• Secure the inside pulley cover with two screws on the

right hand side of the head, just bellow the hand wheel

• Set the outside cover together with the inside, then secure

with screws on the right hand face.

Tool Tray

• Place the tool tray on the front of the machine and secure

with the two supplied screws.

Randall UnIOn lOc k -StItch

Installation

Since 1858

www.Campbell-Randall.com

Wax Pot

• Place the wax pot over the stuf on the back of the

machine

• Pivot the wax pot up to the the machine casting and lock

in place with the clamping nut.

Presser Foot Spring

• Place the upper bracket and spring on top of the machin

head

• With the left hand, compress the coil spring and push the

bracket into the hole in the casting.

• With the right hand, secure the bracket in place by

tightening the screw with a slotted screw driver.

Randall UnIOn lOc k -StItch

Thread / Needles & Awls

Randall UnIOn lOc k -StItch

Since 1858

Technical Support

1-800-327-9420

SeTTINg The NeedLe

1) Make sure that the needle is put into the nee-

dle bar (UL-210) as deeply as possible, then

tighten the needle bar screws in place.

2) Insure that the hook of the needle is looking

directly at the operator.

SIzeS OF NeedLeS TO ThReAd

Sizes will vary between applications.

Appearance of Chisel Point Awl: Turning the

awl so the edge of the blade will start its cut in a

different position can change the appearance of

the stitch.

Awl Parallel to Stitch Line

Awl Angled Left

Awl Angled Right

Awl Perpendicular to Stitch Line

NeedLeS & AwLS

Orders for needles and awls must specify the

quantity required, the size number, and also class

and variety. The following is an example of an

order with sufcient information: “100 UNION #2

Awls, Chisel Point”

Needles

• NOTE: The needle size is determined by the

size of the thread you sewing with.

• Needle Sizes: 1, 1 ½, 2, 2 ½, 3, 3 ½, & 4.

Awls

• Awl Sizes: 2, 2 ½, 3, 3 ½, 4, & 5

• Chisel Point Awl – harness or straight work.

• Oval Point Awl – boot siding, vamp closing &

belts.

• NOTE: The awl size should be 1 to 1-1/2 sizes

larger than the size of the needle. Make sure

that the awl is sharp and does not spring or

glance off the work when entering the work.

Synthetic

Twisted

Natural

Cord

Needle Size

138 3 cord

1 to 1-1/2

207 4 cord

1-1/2 to 2

277 5 cord

2-1/2 to 3

346 6 cord

3 to 3-1/2

415 7 cord

4 to 4-1/2

554 8 cord

4-1/2

693 9 cord

SeTTINg The AwL

1. Turn the hand wheel so that awl bar (UL-85)

is at its highest position. Loosen the awl set

screw and remove the old awl

2. Insert the awl into the awl bar as far as it will

go. Set point in desired position. It is common

to have the point set a little to the right of

being squared across

3. Tighten set screw in awl bar

SewINg ThReAd

• The UNION can use thread size 138 to 554 synthetic or 3 to 12 cord cotton or linen

• Use only Left Twist thread in the machine (twist of the bobbin thread is not important). To determine

the thread twist, hold the thread and twist it counterclockwise between the thumb and forenger. If the

strands wind tighter, the thread is left (Z) twist. If the strands unwind, the thread is right (S) twist.

• If you are using a natural thread, wither linen or cotton, the label end of the spool of the thread must

be pointed up when placed in the thread holder. The bobbin thread should be one size smaller than

the top thread for a better lock. Make sure that the thread is not old, dry, or right twist.

• If you use a larger thread with an undersized needle, skipped stitches or frayed thread may occur.

Randall UnIOn lOc k -StItch

Threading

Since 1858

www.Campbell-Randall.com

THREADING THE WAX POT

1. Mount your thread on the spool holder, with the side up

as indicated on the spool.

2. On the top of the wax pot, bring the thread through the

extended wire rst and then through the small hook.

3. Go underneath the tension disk and around over the top

of the disk.

4. Lift the arm (UL-30) out of the wax pot. Draw the thread

o over the top roller, down over the bottom roller and

then back over the top roller again. NOTE: If the thread

is carrying too much wax on it, then twist the thread

twice over then place back on the roller. This will clear off

excess wax.

5. To complete threading the wax pot, tighten the thumb nut

(UL-34) to secure the arm into the wax pot.

UL-30

UL-34

UL-531

THREADING THE MACHINE

6. Fig. 1 : Put the threading wire (UL-531) through the wax pot

extension and pull the thread through.

7. Fig. 1 : Turn the hand wheel to get access to the lock (UL-

145). Put the threader through the lock (UL-145), grab the

thread and pull down through the lock (UL-145).

8. Fig. 2 : Now, to pull the thread through the bottom of the

lock (UL-145), put the threader (UL-531) thru the tension

spring (UL-157) and roller on the bottom of the tension

spring. This should put the thread behind the roller.

9. Fig. 3 : Turn the hand wheel until the take-up (UL-135) is at

its lowest point. Put the threading wire towards the back of

the machine in between the spring and metal base. Put the

threader (UL-531) through all 3 pieces at one time. Take the

threading wire and place the thread between the lock (UL-

145) and the roller (UL-147).

10. Pass thread through the Thread Guide (UL-165) and and

pull it through, leaveing about 8 inches loose. Note:make

sure that the thread pulls free.

11. Lift the foot, pull the thread through the slot and then pull

the thread towards the back of the machine.

UL-34

Since 1858

Technical Support

1-800-327-9420

Randall UnIOn lOc k -StItch

Wax / Bobbin

Randall UnIOn lOc k -StItch

Winding the Bobbin

• For natural threads, leave the label up on the spool of thread

• Put the thread through the extended wire of the bobbin winder and then through

the small wire hook. Come over the top of the thread disk twice for better

tension adjustment.

• Slide the threader (UL-531), through the wax pot and grab the thread and pull it

through the wax pot. The nuts on the wax pot will turn and adjust how much wax

to be applied on the thread.

• Fill the bobbin with equal tension (DO NOT wind the bobbin either very tight or

very loose, but with rm, even tension). Bobbins that are wound, either, very

tight or very loose, or in the same bobbin, tight and loose, will cause the stitch

length to vary all over the place; and this is the cause of the problem.

• Start off by winding the thread over the top of the bobbin a couple of times by

hand. Again the thread, coming out of the wax pot, should feed over the bobbin.

The bobbin will spin in a counter clockwise motion. Do not overll the bobbin.

Leave a small open area so that the thread is not unraveling off of the bobbin.

Threading the Bobbin

• Insure that the bobbin spring (UL-292) has been placed in the

shuttle with the prongs of the spring bent facing the bobbin (to

the operator’s right).

• Put the bobbin into the shuttle. The thread should ow off

the bobbin easily, from the top and the bobbin in a clockwise

rotation.

• Place the bobbin cover (UL-291) over the bobbin and close

the bobbin door. Make sure that a length of thread is pulled

out of the bobbin door between the spring and the door latch.

Removing the Bobbin

• Release the cover latch and open bobbin door

• Remove the bobbin cover (UL-291)

• Remove the bobbin (UL-290)

BOBBIN SeTUP

ThReAd wAX &

UBRICANT

Fresh wax strengthens the thread

and causes it to stick in place. The

stronger the thread, the less breakage

in the operation of the machine. Wax

will also lubricate your thread for

smoother operation. Wax is especially

recommended for threads made of

natural fibers.

Liquid Thread Wax

• Mix your wax thoroughly to ensure good results.

• Before sewing, clean your machine, oil rollers and

gummed up mechanisms. Pull out and cut off both upper

and lower threads that have hardened.

• Only use enough liquid wax in your machine wax pot to

cover your thread (approximately half full) or enough for a

days use. Anything in excess may thicken before it can be

used.

• Do not neglect to renew wax frequently, or your thread

may become unreliable and break. The fresher your wax,

the better your machine will work.

• It is best to wind your bobbins as you use them, as a fresh

bobbin will do better work than an old one.

• Be careful to have strippers in wax pot tight enough to

clean off all surplus wax

• Adjust Strippers as necessary and clean out the Wax Pot

occasionally

LAX Wax - Water Based Wax

• If LAX Wax Thread Lubricator is used, it is possible to thin

or clean the lube with water.

Hot Wax

• If hot wax is desired the machine must be requested with

special ordered heated wax pots

Thread Lubricant

• When sewing with synthetic threads, Lily White Oil or

Silicone Lubricant can be used.

Since 1858

www.Campbell-Randall.com

Randall UnIOn lOc k -StItch

Sewing

TO COMMeNCe SewINg

NOTE: Read this manual thoroughly before sewing on the UNION for the rst time!

To Prepare for Sewing:

• Grip the top thread behind the presser foot with the left hand

• Slowly turn the balance wheel counterclockwise one full rotatation.

• The loop should catch the bobbin thread and pull it through the hole in the needle plate

• Lift the foot and pull about 8” (200 mm) of thread (from both top and bottom) through to the back of

the machine

• NOTE: When the take up (UL-135/UL-141) is at it’s highest point, the thread is locked. Turn the

balance wheel to lower the take up and release the thread.

• Turn the balance wheel unitl the awl is about to enter the work rst. The machine is now ready to sew.

To Commence Sewing:

• Lift the presser foot, place material under the presser foot, then lower presser foot

• Hold the loose thread in the left hand and commence sewing. The machine will pull the top thread on

the rst stitch.

• Let the machine do the feeding and do not twist or distort the work. All that is required of the operator

is to guide the work, and the machine will feed properly and sew a consistent, even stitch.

• NOTE: The machine may be in perfect adjustment and still fail to sew satisfactory if the operator is

careless in handling the work, or does not adjust the machine to accommodate for a difference in

work.

To Remove the Work:

• Stop the machine when the take up (UL-135/UL-141) is at it’s highest point and the thread is locked.

• Turn the balance wheel to lower the take up and release the thread.

• Remove your work and cut your thread with about 8” (200mm) left loose on the machine.

To Lock the Stitch:

• Although it is not always required, it may be necessary to lock your rst and last stitch in some

applications. This method prevents the threads from coming apart on the ends, and can be done

manually.

• Simply make the rst stitch, stop the machine just before the awl desends into the material, raise the

presser foot, position the work so that the awl will descend next to the rst hole of the last stitch made,

and then continue sewing along the desired line.

• The awl should descend just to the side of the rst stitch, otherwise, if the awl was set directly over

the thread it would cut through the previous stitch. If done correctly, the two stitches will be uniform so

that they will appear as one.

• It is also possible to lock the stitch by tying the end threads together, melting synthetic thread ends, or

locking the end with a rivet or similar fastener.

Since 1858

Technical Support

1-800-327-9420

Randall UnIOn lOc k -StItch

Adjustments

The following adjustments and explanation of reasons for making them

are to simplify the servicing of the UNION Lock-Stitch machine

• The successful operation of UNION machines can only be assured if proper maintenance and genuine RANDALL parts are used.

RANDALL LEATHER MACHINERY is not responsible for machines or parts that are damaged due to excessive speed, improper

installation, unauthorized modications, improper adjustment, poor maintenance, or use of improvised or generic parts.

• We wish to caution the operator not to strain the small screws and nuts. Use good judgment in handling them and they will not break

• At such a time as a change is made in a individual adjustment or there is a replacement of a part on the machine, a careful check

should be made of all adjustments and settings that may be directly or indirectly affected to insure that no change has taken place in the

assemblage.

• When making a replacement of a part in an outstanding machine, make certain that the correct component parts are being used.

• Consult the catalog for the proper presser foot and throat plate to use. There are many of various types of attachments, with each

serving a special purpose in respect to the different types of materials and the many kinds of work, which these machines are active in

sewing.

• RANDALL LEATHER MACHINERY reserves the right to make changes or improvements at any time, without thereby incurring any

obligation either to install the same on machinery or equipment previously sold or install the old part which has been changed, improved

or omitted in new machines or equipment subsequently sold. Prices and equipment subject to change without notice.

Inspection of Common Adjustments

Allowing that a machine is in good condition from a standpoint of wear and lost motion,

a quick check-up of the essential settings can be made in the following order:

• Check the hole for the needle in needle bar. Remove all dirt.

• Check for perfect alignment of awl with needle.

• Make sure that all screws remain tight.

• Keep the machine well oiled, (except in foot lift area).

• The wax pot should be approximatly half full of wax.

• Before making any adjustments, make sure that the needle and awl are not bent.

• The best way to test is to roll the needle and awl on a smooth at surface and see that it rolls true.

7. Tension on shuttle thread must not be too strong. Make sure there is no gap between the inside bobbin cover and the

shuttle.

11. When assembling the parts, make sure each piece that you put together is free without any play or binding.

12. All lower rocker shafts should be free without any side wise movement or binding.

Oiling & Cleaning

Oiling:

• The successful and economical operation of all machinery depends on thorough cleaning and oiling. The operator will

save much trouble as well as money by systematic careful attention to the machine in these respects. It is recommended

that the machine be cleaned oiled daily. Oiling the machine not only lubricates, for smoother operation, but it also cleans it

from dirt and contaminates that can shorten the lifespan of the machine.

• NEVER USE GREASE, on any mechanism. Grease will collect dirt and contaminants that will grind and damage parts.

• DO NOT OIL THE FOOT LIFTING MECHANISM (Parts UL-120 to UL-127). Oiling in this area will cause the presser-foot

not to lift and will result in inadequate feeding.

Cleaning:

It is advisable to keep the machine clean to prevent the build up of dirt and wax. This build up can damage mechanisms and

stain the products being sewn. Regularly clean the shuttle mechanism, arch covers, and thread path. If the machine uses

hard wax, regular cleaning is critical.

ADJUSTING THE FOOT PRESSER

• Enough pressure must be used to hold the work rmly in the

needle plate. Light work will not require as much pressure as

heavy work. Too much pressure will cause the presser-foot

to mark you material. If the pressure is too light, the work will

move and irregular stitching or a broken needle may result.

• To apply more pressure on the foot, open the nut (UL-15) on

the top of the spring (UL-101) and turn the spring adjusting

screw (UL-103) clockwise for more spring pressure on the

foot.

• When you have enough spring pressure on the foot, tighten

the nut on top of the spring.

ADJUSTING THE FOOT LIFT

• The foot should lift just high enough to clear the work.

If the foot doesn’t lift high enough, the work not move

effectively causing smaller stitches or the awl will cut the

leather.

• Turn the balance wheel, until the foot lift adjusting arm

UL-116 (on the top left of the machine, if the operator is

sitting in front), is turned with the 2 screws facing to the left

of the machine.

• To make the foot lift higher, loosen the inside screw UL-

117 and tighten the outside screw.

• If the foot is lifting to high, loosen the outside screw and

tighten the inside screw.

• NOTE: Never put oil in the foot lift area, parts UL-120 to

UL-127. Oiling in this area will prevent the mechanism

from lifting.

UL-15

UL-101

UL-103

UL-116

UL-117

ADJUSTING THE LOWER FOOT LIMIT

• To set the lower limit postion of the presser foot, adjust

screw UL-21, located to the back left of the UL-101 spring.

• To lower the foot to the minimum position, loosen the nut

(UL-20) and turn the UL-21 screw counter-clockwise

• The UL-106 lifting arm will move lower onto the casting of

the machine. After setting the postion, re-tighten the nut

(UL-20).

PRESSER FOOT MOUNT

• If you have play in the foot, tighten the screw on the back

of the foot bar (UL-100)

Since 1858

www.Campbell-Randall.com

Randall UnIOn lOc k -StItch

Presser Foot

Presser Foot Adjustment

Randall UnIOn lOc k -StItch

Thread Lock / Tension

Since 1858

Technical Support

1-800-327-9420

REGULATING THE THREAD LOCK

• Normally the lock should lay towards the bottom portion of the

work. The position would need to be changed if a thicker needle

plate is installed.

• First bring the take up (UL-135/UL-141) to its’ highest point.

• To regulate the thread lock by adjusting the position of eccentric

screw (UL-164).

• Loosen the nuts (UL-20) holding this screw on the back of the

brass block.

• By turning the UL-164 screw, the brass part UL-160 will move. If

the lock is showing on top, move part UL-160 up. If the lock is

showing on the bottom of the work, then lower part UL-160.

• When nished, tighten the nuts on the UL-164.

THREAD TENSION

• Slight tension is needed on both the top and bottom threads.

Proper tension has been obtained when the thread pulls out easily

with light tension, without excessive binding. It is recommended to

use less tension when working with threads made of natural bers.

• To give more tension on the top thread, tighten the tension spring

nut (A) on upper wax pot.

• To apply more tension on the bobbin thread, adjust the lower

screw on the bobbin door (B). Loosen the nut, adjust the screw

(UL-243), and then tighten the nut (UL-174). Loosen screw to

decrease tension and tighten screw clockwise to increase tension.

• The upper screw (C) is used to move this part in and out in order

to compensate for wear.

UL-160

UL-164

STITCH LENGTH

• The stitch length is best set when the needle starts to desend after

feeding, and the shuttle point is in the 11 o’clock position.

• On the front rocker arm (UL-200) is a link that is horizontal to the

operator (bolt UL-226 and link UL-224).

• Adjust the link UL-224 up for a shorter stitch or down for a longer

stitch.

• Stitch length can be adjusted from 4 to 12 stitches per inch.

Randall UnIOn lOc k -StItch

Thread Guide

Since 1858

www.Campbell-Randall.com

THREAD-GUIDE (UL-165) ADJUSTMENT

Setting the Thread-Guide:

• Set the guide so it delivers thread well into the needle

throat (hook) of the needle.

• The guide should clear the needle by approximately

1/16” (1.5mm) as it circles to the left of the needle and

slightly to the back.

• When the take-up is at its highest postion, just before

looper begins to move forward, the guide should be

about 1/64” in front of the looper.

• Adjust the thread guide forward and backward with

screw UL-173.

• Always check thread guide (UL-165) for sharp spots

that could break or strand the thread. Pass the thread

back and forth through the hole of thread guide to make

sure that this area is smooth.

LOOPER FEED CAM

• With the shaft standing upright, the at area should be to

your left, cam (UL-181/ UL-161). The screw in the cam

should be all the way up. The looper can be made to delay

the thread, by loosing the screw in the take-up cam and

moving the screw to the top. The looper should hold the

thread until it has descended into the material. If not, the

thread would fall off the needle at its’ highest peak.

SeTTINg UL-180 LOOPeR :

• The thread arm looper (UL-180) should be set so it will

cast off the thread as the needle draws the thread loop

into the surface of the work.

• At the furthest point of its back swing (toward the

operator), the notched edge of the looper should be

approximately 3/16” behind the awl and approximately

3/16” below the thread guide. On the forward swing,

the looper should just clear the side of the presser foot.

The thread looper needs to move close to the needle

on the left side without touching.

• Test the looper for any play side to side. Side play can

be taken out by loosening UL-188 bushing screw, than

tap end of stud and re-tighten the screw. Replace if

worn.

• Keep looper free from sharp edges that can strand

the thread. If the looper is out of adjustment, it can rub

against the thread guide creating sharp edges. If there

are rough spots, use emery cloth or cord to smooth.

Note: These adjustments are normally made only

when related parts have been installed or the

machine is knocked out of alignment. Inspect all

other adjustments before resorting to realigning

the needle and awl.

Alignment of the Needle - RIghT TO LeFT

• Remove the bottom cover UL-300/UL-301. This is on the bottom left side of the machine. You will see 3 nuts (UL-10),

once you take off the cover. The two center nuts will adjust the needle left or right.

• First, on the bottom left of the machine open the screw (UL-13) on the needle disk (UL-214). You, then need to open the

screw (UL-161) on the back of the machine (see the instruction section, “Adjusting The Needle Front To Back”). You do

this so when you perform the following adjustments, the machine will not bind. First, you need to open the two nuts (UL-

10), both on the front end of the casting and on the back end of the casting.

• NOTE: You will need only a slight adjustment here. If you want to move the needle to the left, just open the right bolt

(UL-11) (of the three on the front of the casting) counter-clockwise 1/8 turn and then turn the left screw equally. You need

to move the bolts on the back end of the casting equally clockwise. Also, once adjusted, tighten all the nuts (UL-10), both

front and back ends.

• NOTE: when you move the needle left or right, you need to re-adjust the alignment of the shuttle point (UL-276) to the

needle. If the thread breaks and jumps inside of the bobbin, there are 2 reasons for this: A) You do not have enough

Randall UnIOn lOc k -StItch

Alignment

Since 1858

Technical Support

1-800-327-9420

Inspecting the Alignment

Note: Before inspecting or changing the

alignment, insure that the needle or awl are not

bent.

• When the needle and awl are perfectly

aligned, the needle should comes up

through the material without exing or

hitting the sides of the awl hole.

• To see the alignment, set a piece of paper

under the foot. Turn the hand wheel

toward you until the awl makes a hole

in the paper. Again turn the hand wheel

and watch the position of the needle as it

ascends through the awl hole.

• If the needle appears to rip the paper

either in front or back of the awl hole,

adjust the alignment with the procedure

below.

Needle - FRONT TO BACk

Before changing this alignment, make sure the awl is ad-

justed properly.

• Turn the hand wheel until the needle starts to ascend.

• Locate the cutout, on the bottom rear corner, left side of

the machine.

• Insert a screwdriver through the cut out and loosen screw

UL-161.

• Apply a wrench to the end of the nut, located to the left of

the bracket.

• This nut is part of the rocking shaft (UL-223). If you turn

the wrench away from you, the needle will move forward.

If you move the wrench towards you, the needle will move

back.

• After setting, tighten screw UL-161.

ALIgNMeNT OF The NeedLe ANd AwL

UL-161

UL-223

UL-161

Awl - FRONT TO BACk

Both the needle and awl should be approximately 1/16” from

the front edge of the hole in the needle plate.

• The awl bar can be aligned by adjusting the gibs (UL-

77/78) with the slotted screws on the front face of the

head.

• There should be no play awl bar, but do not over tighten

the gibs which will cause the action to bind

Needle - FRONT TO BACk

• If there is play in the needle bar adjust the gibs (UL-

197R/L). Do not over tighten the gibs.

• Adjust the position of the shuttle housing (UL-235), by

loosening the four nuts (UL-229) and move the housing

forward or back by turning the screws UL-237.

• Once the needle and awl is approximately 1/16” from the

front edge of the hole in the needle plate, secure the nuts

(UL-229).

Randall UnIOn lOc k -StItch

Timing

Since 1858

www.Campbell-Randall.com

TIMINg OF The UNION LOCkSTITCh

COURSe AdjUSTMeNT TIMINg

NOTE: Do not make changes to the coarse adjustment unless there

is insufcent movement to allow normal ne adjustments to the

shuttle and needle timing.

• On the top right of the machine you will see a cut-out that allows

access to adjust the gear UL-57. This is the main timing point

to synchronize the the upper section (awl, thread guide, looper,

take-up, and foot lift motion) with the lower section (needle, feed,

and shuttle motion)

WHEN NECESSARY, timing is accomplished as follows:

1. Turn the balance wheel so that the take-up, (UL-135/UL-141), is

at its highest point before it begins to drop.

2. Loosen the set screws on the bevel gear (UL-57) until is can

slide on the horizontal shaft (UL-50) and disconnect it from the

gear on the vertical shaft. This will allow the top of the machine

to work freely without motion in the bottom of the machine.

3. Hold gear UL-57 so it will not turn and, at the same time, using a

wide blade screw driver to pry against the teeth, turn the shuttle

shaft driving gear UL-72. DO NOT loosen the set screws. Make

one complete cycle, then bring the ascending needle barb point

to 1/4’” below the lower surface of the throat plate. As another

reference, the tip of the needle is 1/16” to 1/8” below the cut out

in the stitching plate (part UL-250*). This is where the bottom

portion of the machine needs to be set.

4. Move the gear UL-57 back to its engaged position with the

vertical shaft gear, leaving a very small amount of play between

the two gears. Make certain that the set screws are both over

the at spots on the shaft which may require the removal of the

set screws to locate, which are 90° to each other. Tighten one

set screw, then recheck the timing. If this is correct then set both

screws snug with a “T” wrench and pliers. If the balance wheel

moves when you tighten these screws, then the gear is not set

directly on the ats and it should be reset.

Shuttle Point Alignment - RIghT TO LeFT

• The needle should be on center with the shuttle point (UL-276).

• If the needle is straight, align the needle to the center of the shuttle point by adjusting the two screws on either side of the

shuttle housing (UL-235).

• Loosen the screws and slide the shuttle to the left or right of the operator.

• NOTE: Make sure that the hook of the needle, directly faces the operator. If the hook on the needle is slightly turned, it

will cause skipping or breaking of the thread.

Feed of the Needle in Relation to the Foot

• One way of knowing if the feed is out of adjustment, is that the stitches will suddenly get very small. This is because the

foot is not lifting and allowing the work to be pulled.

• Just as the needle is at its highest position, just as it begins to pull back on the work, the foot should begin to lift. The

needle should feed all the way back and begin to drop when the foot begins to drop.

• The adjustment is behind the UL-226 bolt that you used for determining the stitch length. Inside on the lower shaft is

cam UL-219. This is not a normal adjustment, so please contact Randall before changing.

• When the bell (UL-214) is upward, the UL-219 feed cam eccentric screws (UL-220) should be in a position where one is

in a downward position and the other facing the back of the machine.

• NOTE: The feed timing will affect the adjustment of the UL-165 Thread Guide and UL-180 Thread Looper

Randall UnIOn lOc k -StItch

Timing

Since 1858

Technical Support

1-800-327-9420

Shuttle Timing - FINe AdjUSTMeNT

The thread should release off the needle about halfway

on the shuttle hook. If the needle holds the thread too

long or too short, then the shuttle needs to be delayed or

advanced.

• On the lower right hand corner of the machine, in

a cut out in the casting, you will see a gear (UL-72)

with 2 screws on it. The shuttle gear shaft has a at

spot under the adjustment screws. Loosening one

screw and tightening the other causes the gear to shift

positions on the shaft, thus affecting the shuttle point

(UL-276).

• To advance the shuttle point, loosen the bottom screw

and tighten the top screw

• To delay the shuttle point, loosen the top screw and

tighten the bottom screw

• The shuttle point should be approxmatly 1/8” (3mm)

from the needle when the needle is on the way down

and level with the hook point. At this position, the hook

is about to enter the loop.

• When the Take-Up UL-135 is at its highest position, the

point of the needle should be about 1/16” below the

plate.

• Time the shuttle point so it just clears the descending

needle. Turn the ywheel back and forth with the

needle point close to the shuttle point to make certain

the needle clears the shuttle point without striking in

either direction.

• NOTE: After timing the shuttle point, it may be nessary

to change the ne adjustment of the needle

UL-276

UL-72

Needle Timing - FINe AdjUSTMeNT

This adjustment should be made AFTER timing the shuttle

point

• Locate the timing gear on the lower, far right cut out of

the casting.

• To raise the the needle, loosen the top screw and

tighten the bottom screw.

• To lower the the needle, loosen the bottom screw and

tighten the top screw.

• When the take up roll is at its highest point, the barb

of the needle should be 1/4” below the surface of the

throat plate.

Randall UnIOn lOc k -StItch

Trouble Shooting

Since 1858

www.Campbell-Randall.com

Reference Points

Move the hand wheel until the take-up is at its highest point.

In this position:

• the needle is 1/16” below the plate

• the gap between the needle and the shuttle point should

be about 1/16”

• part auto foot lifter lever (UL-115) should be pointing

straight down

• the thread looper (UL-180) is just about to pick the thread

Move the hand wheel until the take-up is about to desend. In

this position:

• the Thread Guide UL-165 takes the thread into the

needle

• The awl should be at its highest point

Move the hand wheel until the needle begins to desend. In

this position:

• the thread looper (UL-180) should release the thread just

as the needle desends into the material

Move the hand wheel until the hook point is at the 11 o’clock

position:

• the thread should cast off the shuttle

Randall UnIOn lOc k -StItch

Trouble Shooting

Randall UnIOn lOc k -StItch

Since 1858

Technical Support

1-800-327-9420

Since 1858

SKIPPING STITCHES

Skipping stitches may be caused by one of several reasons and is usually a matter of adjustment.

1. Damaged Needle

2. Height of the needle is improperly set

3. The hook of the needle is turned and not properly catching the thread

4. Thread Tension not set

5. Thread-Guide out of alignment and is not delivering the thread into the eye of the needle

6. Thread-Arm is misaligned, therefore allowing the thread to drop before the needle eye enters work

7. Awl and Needle too small for work, especially in work of heavy construction

8. Shuttle Point out of alignment and is not dividing loop. (Note: Use a new needle when checking)

9. Needle and awl out of alignment

10. The needle holds the thread for too long or too short. Adjust shuttle timing.

11. Excessive wear on the Thread-Guide, Thread-Arm, or Needle mechanisms

IRREGULAR STITCHS

1. Small knots at random intervals under work (generally without breaking the thread) can be caused by uneven bobbin

tension. This can be caused by the bobbin not being wound evenly, poor quality thread, or use of an old waxed bob-

bin that dry. With older macines the bobbin tension mechanism can be worn and needs servicing. Wear on the shuttle

mechanism cuases periodic snags.

2. Irregular stitches or knots on top of work caused Take-Up Spring UL-157 being out of adjustment or bent out of

shape. The take-up spring should hold in such a manner that there is no slack between the take-up spring and the thread

guide.

STRANDING OR BREAKING THREAD

1. Needle damaged or bent

2. Needle barb is out square and causes stranding or breaking of thread by catching only part of the thread

3. Thread of wrong twist or poor quality. Avoid knotty natural threads. Thread is knotting in the topside caused by exces-

sive twist. Common with poor quality natural threads or synthetic threads that have too much stretch or excessive coiling

especially near the end of a spool.

4. Needle not casting off thread after shuttle picks up loop. Check needle timing and its position in relation to the shuttle

point.

5. After adjustment or changing from a high throat plate to a lower one the thread lock pulls tighter into material, causing

breakage. Normally leaver 2 to 2-1/2” of thread under the material. Reset thread lock lower.

6. Poor condition of Wax or Thread Lubricator. Always use fresh waxes and lubricants.

7. Bobbin thread tension too stiff, cuasing the thread to catch on the bobbin door spring.

8. Shuttle tension too weak, causing the thread loop to catch inside the boobin

9. Sharp edges on the presser-foot, needle plates, shuttle, looper or thread guide. Smooth sharp edges with emery cloth or

abrasive cord. Test by running thread through the hole and forcing it over the edges, pulling back and forth. Needle plates

or presser-feet may have sharp edges as a result of awl or needle damage from improper handling. Thread guide and

looper may have sharp points if they are rubbing together when sewing.

10. Thread Guide UL-165 incorrectly adjusted causeing needle hook to split the thread or hits the needle

11. Too much take-up. Normally leaves broken thread on top of work. Reset machine timming on upper section bach one

tooth.

12. Check that the alignment of needle is on center with shuttle point. In older machines there can be excessive play in the

shuttle mechanism, or where on the thread groove on the shuttle is deep enough to cause the thread to snag.

BREAKING NEEDLES

1. Needle is deected or bent while sewing thick, hard or difcult work. Use larger Needle and Awl.

2. Needle is too small for the thread

3. Needle comes in contact with the hardware or strikes exisitng hole at a bad angle.

4. Needle sets too high and hits shuttle point, possibly because bad shuttle timing or dirt in needle bar hole.

5. Needle alignment incorrect, causing needle to punch its own hole

6. Awl is bent

7. Feed timing off, with foot not lifting in time for needle feed

8. Presser-Foot Lifting mechanism worn or out of adjustment, not lifting for needle feed

Randall UnIOn lOc k -StItch

Trouble Shooting

Since 1858

www.Campbell-Randall.com

LOOSE STITCHES - Bottom

1. Make certain machine is correctly threaded.

2. Top tension is too loose

3. Bottom tension is too tight. A strong bobbin thread may

cause trouble in pulling the thread-locks into the material.

4. The adjustment of thre lock is set too low. Often evident

when the needle plate elevation is changed.

5. Uneven bobbin tension. Rewind the bobbin

6. Check threading of shuttle and that the bobbin thread is

unwound from the bottom

7. Inspect the thread to be of good quality

8. The shuttle thread is too dry, if working with a waxed bob-

bin

9. The awl being set too low sometimes causes a short

loop on throat plate side, and the shuttle thread will whip

around the awl.

LOOSE STITCHES - Top

1. The thread arm pulling too large a loop.

2. The thread lock is set too high.

3. The upper thread tension is too high.

4. The shuttle thread tension is too weak.

IRREGULAR STITCHES AND SHORT STITCHES

Irregular stitches may be caused by one of several reasons

and is usually a matter of adjustment

1. Bad awl

2. Not enough presser-foot lift

3. Presser foot mechanism not lifting dut to worn parts

4. Oil on the Presser-Foot mechanism causes the lift lever

to slip

5. Crowding your work, or work hanging up somewhere on

the machine

6. Forcing work into machine, or holding work back, esspe-

cialy on large parts

7. Stitch length is too small for Needle and Awl combination

or thread

8. Feed timing incorrent, not allowing for foot to lift before

needle feed

WORK DOES NOT FEED PROPERLY

When your work does not feed properly it is usually because

the presser foot does not lift, as it should to allow the awl to

feed the work along. When the presser foot does not lift prop-

erly it can be due to one or more of the reasons listed below:

1. Lifting lever is worn, broken, or adjusted improperly.

2. Check the Presser Foot Bar Spring or weakness or break-

age.

3. Check the lift of the presser foot bar. There should be a

1/8” lift at time of feeding work.

TROUBLE SHOOTING—Feed Timing: If your feed timing is

incorrect, it will affect your feed of

your work resulting in smaller or irregular stitches. It will, also,

affect the needle in relation to part

#165 and #180. TO CORRECT this problem, turn the hand

wheel until part #214 has the bell straight

upward. At this point, the screws #220 on part #219(cam)----

one screw should be pointing straight

down to the oor and the other screw should be pointing to

the back of the machine. Now, when the

needle is all the way at its’ highest point and starts to move

forward, the pressure foot should just start

to move up and the needle starts to carry the material over.

TROUBLE SHOOTING---Needle and Awl: The needle and

awl should be approximately 1/16” from

the front of the plate to the needle. TO CORRECT this prob-

lem, loosen the 4 nuts(#229) on part (#235) and adjust part

#235 to the front or rear by turning the 4 #237 until you obtain

your 1/16” ,then

securely tighten the nuts #229.

TROUBLE SHOOTING---Tighten or loosen the Thread: To

tighten the stitches, loosen the two (2)

nuts #20 on part #164 then, with your wrench, turn eccentric

stud #164 upward. This will take the

slack out of the thread. To loosen the thread, do the reverse,

then securely tighten the 2 nuts #20.

TROUBLE SHOOTING---Looper: The looper---part (#180)

should release the thread as soon as the

needle is about to decent into the work. TO CORRECT this

problem if the looper does not work pro-

perly, loosen the screw (#161)—thread guide screw on

cam—on part (#170) and move the screw up or

down. The standard position for this screw #161 is at the

down, must, position. Part #165, the looper

should be approximately 1/64”in front of part #180 when the

take-up is at its’ highest position and just

before part #180 starts to move forward. Screw #173 is used

to adjust the looper #161 backward and

forward.

Randall UNION Lockstitch User manual

Brand: Randall

Model: UNION Lockstitch

Type: User manual

Download PDF

report

Randall UNION Lockstitch User manual

Randall UNION Lockstitch User manual

Other documents