Pneumatic Arm Triple Monitor Desk Mount with Pull Handle
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v101g3
3
SKU: STAND-V101G3
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
PACKAGE CONTENTS
WARNING!
A (x1)
Base
B (x1)
Lower Arm
C (x1)
Gas Spring Arm
M (x1)
Cover
N (x1)
Clamp
L (x1)
Clamp
Brace
J (x1)
Grommet
Plate
K (x1)
So Pad
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
M-A (x12)
M4x12
D (x1)
Le Arm
E (x1)
Right Arm
F (x1)
Center Arm
G (x3)
VESA Plate
H (x1)
Handle
I (x1)
Clamp Plate
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-B (x12)
M5x12
M-C (x12)
D5 Washer
O (x10)
M6x12 Flat Head
Bolt
R (x1)
3mm Allen
Wrench
S (x1)
4mm Allen
Wrench
Q (x2)
M6x22 Bolt
P (x4)
M6x12 Bolt
T (x1)
6mm Allen
Wrench
3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Attach clamp brace (L) to base (A) using M6x12 flat head bolts (O) and tighten
with 4mm Allen wrench (S). Apply so pad (K) to underside of base. Loosen bolts
on back of clamp (N), leaving 6mm of thread exposed.
TOOLS NEEDED
2.2 - 13.2lbs
(1 - 6kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
For a desk thickness of 3/8” - 2-1/2” (10 - 58mm),
hang assembled clamp into top 4 slots of clamp
brace, or for a desk thickness of 2” - 3-3/8” (50 -
85mm), into lower 4 slots. Place clamp plate (I) on
top of clamp bolts. Position base on desktop and
tighten clamp bolts evenly using 6mm Allen wrench
(T). Attach cover (M) to back of clamp brace.
PER SCREEN
4
STEP 1 (Continued)
OPTION B: Grommet Base Installation
Attach grommet plate (J) to base (A) using M6x12 flat head bolts (O) and tighten with
4mm Allen wrench (S). Apply so pad (K) to underside of base. Position base over
grommet hole in desktop, or drill a 3/8” (10mm) hole through the desk for installation.
Remove a bolt from the clamp (N), then insert removed bolt with clamp plate (I)
up through the underside of the desk and tighten to the base using the 6mm Allen
wrench (T).
STEP 2
STEP 4
Place lower arm (B) on top of base, and secure
by turning the lower screw in back with 3mm
Allen wrench (R). Optionally, also tighten the
upper screw to restrict swivel movement to +/-90
degrees.
Install center arm (F) to gas spring arm using
M6x12 bolts (P), making sure arrows on back are
pointing up, and tighten with 4mm Allen wrench
(S).
STEP 3
Place gas spring arm (C) on top of lower arm, and
secure by turning the screw in back with 3mm
Allen wrench (R).
STEP 5
Mount handle (H) to back of center arm using
M6x22 bolts (Q) to one of the positions shown
in the diagram according to the size of your
monitors. Tighten with 4mm Allen
wrench (S).
5
STEP 6
Attach le and right arms (D, E) to center arm using M6x12 flat head bolts (O), making sure
open ends of mounting brackets are facing up, and tighten with 4mm Allen wrench (S).
STEP 7
Straighten arms for easier installation of monitors.
STEP 9
Place the monitors with VESA plates into the supports on the arms, then
turn the screw on each support to secure the monitors.
STEP 8
Install the VESA plates (G) to monitors using M4x12 bolts (M-A) or M5x12 bolts (M-B) with
washers (M-C), making sure the large end of each bracket in back is facing up.
6
STEP 10
If needed, adjust gas spring arm to support the monitors using the 4mm Allen wrench (S) . While
holding arm in the straight forward position, turn the screw in back clockwise to decrease support, and
counter-clockwise to increase. Slightly loosen the monitor arm for leveling if needed.
STEP 11
Remove cable cover on upper arm using a Phillips screwdriver. Slide cable cover on lower arm
forward to remove.
STEP 12
Organize cables, then reinstall cable covers to arms.
7
STEP 13
For safety, please do not extend the monitors behind the desk. This may cause instability and tip the
desk over.
Adjust as Desired
LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
/
