Spektrum DXS Transmitter Only Owner's manual

Brand: Spektrum

Model: DXS Transmitter Only

Category: Toys & accessories

Type: Owner's manual

Spektrum DXS and AR410 4 CH Receiver

Spektrum DXS und AR410-Empfänger mit 4Kanälen

Spektrum DXS et récepteur AR410 4canaux

Spektrum DXS e ricevitore AR410 a 4 canali

NOTICE

All instructions, warranties and other collateral documents are subject to

change at the sole discretion of Horizon Hobby, LLC. For up-to-date product

literature, visit horizonhobby.com or towerhobbies.com and click on the support

or resources tab for this product.

Meaning of Special Language

The following terms are used throughout the product literature to indicate

various levels of potential harm when operating this product:

WARNING: Procedures, which if not properly followed, create the probability

of property damage, collateral damage, and serious injury OR create a high

probability of superﬁcial injury.

CAUTION: Procedures, which if not properly followed, create the probability

of physical property damage AND a possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of

physical property damage AND a little or no possibility of injury.

WARNING: Read the ENTIRE instruction manual to become familiar

with the features of the product before operating. Failure to operate

the product correctly can result in damage to the product, personal

property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution

and common sense and requires some basic mechanical ability. Failure to

operate this Product in a safe and responsible manner could result in injury

or damage to the product or other property. This product is not intended for

use by children without direct adult supervision. Do not attempt disassembly,

use with incompatible components or alter product in any way without the

approval of Horizon Hobby, LLC. This manual contains instructions for safety,

operation and maintenance. It is essential to read and follow all the instruc-

tions and warnings in the manual, prior to assembly, setup or use, in order to

operate correctly and avoid damage or serious injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

WARNING AGAINST COUNTERFEIT PRODUCTS

Always purchase from a Horizon Hobby, LLC authorized dealer to ensure

authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims

all support and warranty with regards, but not limited to, compatibility and

performance of counterfeit products or products claiming compatibility with

DSM or Spektrum technology.

NOTICE: This product is only intended for use with unmanned, hobby-grade,

remote-controlled vehicles and aircraft. Horizon Hobby disclaims all liability outside

of the intended purpose and will not provide warranty service related thereto.

WARRANTY REGISTRATION

Visit www.spektrumrc.com/registration today to register your product.

Spektrum DXS Transmitter and AR410 Receiver

The Spektrum™ DSMX

DXS 7-Channel transmitter is available either as the

transmitter only (SPMR1010), or packaged with a full range Spektrum AR410

4-Channel receiver (SPM1010). The DXS transmitter and AR410 receiver are

each fully compatible with other Spektrum DSMX systems.

The DXS transmitter has a default conﬁguration that is designed to work with

SAFE

technology; a 3-position switch for Flight Modes on Channel 5, and a

momentary switch on Channel 6 to trigger Panic Mode.

Contents

Spektrum DXS Transmitter and AR410 Receiver .........................................3

Speciﬁcations .............................................................................................4

Transmitter Diagram ...................................................................................5

Installing the Transmitter Batteries ..............................................................6

Turning the Transmitter ON and OFF ............................................................6

Receiver Diagram .......................................................................................6

Receiver Installation .................................................................................... 6

Binding .......................................................................................................7

Transmitter Setup .......................................................................................7

Setting Failsafe On The AR410 Receiver ......................................................9

Smart Telemetry and LED Indicators on the DXS .........................................9

LED Smart Battery Usage ..........................................................................10

Wireless Trainer ........................................................................................10

Range Test ................................................................................................10

Adjust Stick Tension ..................................................................................11

Changing the Throttle Ratchet ................................................................... 11

1-Year Limited Warranty ...........................................................................13

Warranty and Service Contact Information ................................................14

Compliance Information for United States .................................................15

Compliance Information for Canada ..........................................................16

Compliance Information for the European Union ........................................ 16

SPMR1010

DXS TRANSMITTER

Type DSMX 7 CH Transmitter

Auxiliary Switches

and Buttons

1 Momentary Button, 2 3-Position Switch,

2 2-Position Switches

Channels 7

Power Supply 4 AA Batteries

Control Mode Mode 2

Telemetry Flight Battery Voltage (Smart ESC required)

Trainer

Wireless; Remote Receiver SPM9747 Required Com-

patible with DSM2 or DSMX transmitters

Data Port

Serial adapter (SPMA3068) included for connection

with the USB Programming Cable

(SPMA3065, not included)

Frequency 2.4GHz

Trim Programming Servo Reversing

SPMAR410

AR410 RECEIVER

Type DSMX 4-Channel Sport Receiver

Dimensions (L × W × H) 45.2 × 20.0 × 13.9mm

Antenna Length Internal

Channels 4; Throttle Port Smart Compatible

Weight 7g

Frequency 2.4GHz

Voltage Range 3.5–9V

Speciﬁcations

Antenna

B Switch (Ch 5 Default)

D Switch (Ch 7 Default)

RGB LED

H Switch

(Throttle Cut Default)

F Switch

(Dual Rate Default)

4 Green LEDs

Throttle/Rudder Gimbal

(Mode 2)

Aileron Trim (Mode 2)

Elevator Trim (Mode 2)

Power Button

Neck Strap Hook

Throttle Trim (Mode 2)

Elevator/Aileron Gimbal

(Mode 2)

Transmitter Diagram

A Button

(Channel 6 Default)

Rudder Trim (Mode 2)

Integrated Handle

Wireless Trainer Port

Programming Port

Battery Holder

Receiver Installation

Install the receiver as recommended by your airplane’s manufacturer and

connect the servos to their respective ports. Double-sided tape or foam can be

used to secure the receiver in place. The AR410 features an internal antenna

design for easy installation in almost any model.

Most ESCs include a circuit (called a BEC) to power the receiver through the

throttle connection. If you do not have a BEC powering the receiver, connect

your 3.5 to 9 volt power supply (battery or dedicated regulator) to the battery

port to power the receiver. The receiver will power ON when power is connected.

IMPORTANT: When using Y-harness or servo extensions with Spektrum

equipment, do not use reversing harnesses. Using reversing Y-harnesses or

servo extensions may cause servos to operate erratically or not function at all.

Battery

Channel 1 / Program Port

(Throttle - Smart Compatible)

Channel 2 (Aileron)

Channel 3 (Elevator)

Channel 4 (Rudder)

Bind Button

Receiver Diagram

Installing the Transmitter Batteries

1. Remove the battery cover from the bottom of the transmitter.

2. Install four AA batteries as shown.

3. Install the battery cover.

CAUTION:

NEVER remove the transmitter

batteries while the model is powered on.

Loss of model control, damage or injury may occur.

CAUTION:

If using rechargeable batteries,

charge only rechargeable batteries.

Charging non-rechargeable batteries may cause

the batteries to burst, resulting in injury to persons

and/or damage to property.

CAUTION: Risk of explosion if battery is

replaced by an incorrect type. Dispose of used

batteries according to national regulations.

Turning the Transmitter ON and OFF

Press and hold the power button to power the transmitter ON. The RGB LED

indicator will illuminate Orange when the transmitter is ON and transmitting. To

power the transmitter OFF, press and hold the power button for 5 seconds.

Binding

The DXS and your receiver must be bound to each other before they will

operate. Binding is the process of teaching the receiver the speciﬁc code of the

transmitter so it will only connect to that speciﬁc transmitter.

1. Push and hold the bind button on the receiver while powering ON the

receiver. Release the bind button once the orange LED starts to ﬂash

continuously, indicating that the receiver is in bind mode. The AR410

receiver will also enter bind mode if you power ON the receiver and then

press the bind button before the receiver has connected to any transmitter.

2. With the throttle in the low position, push and hold the A button while turning

the transmitter ON to put the

transmitter in bind mode.

3. After you set up your model,

always rebind the transmitter

and receiver to set the desired

failsafe positions.

Transmitter Setup

The DXS transmitter has reversible channels with trim programming.

Trim programming is a special setup mode on the DXS transmitter. You can

only enter trim programming at power up. The DXS transmitter does not emit a

signal to the receiver during trim programming to prevent accidental operation.

Normal control operation will not resume until you power the transmitter OFF

and then back ON again normally.

Trim Programming

1. Conﬁrm the channel numbers that need to be reversed.

2. Power OFF the DXS transmitter and the receiver. Leave the aircraft powered

OFF during trim programming.

3. To enter trim programming mode, push and hold the elevator and throttle

trim buttons up awhile you power ON the DXS transmitter.

BIND Status DXS and AR410

Ready to Bind Flashing Orange LED

Bind Complete Solid Orange LED

The RGB LED on the transmitter

will illuminate green to indicate

the transmitter is in trim

programming mode.

4. The ﬂashing green LED corresponds to the selected channel. When the ﬁrst

LED is ﬂashing, the throttle channel is selected (Channel 1)

5. Once the ﬁrst four channels have been conﬁrmed, the LEDs will indicate

channels 5 through 7. Reverse channels as necessary and conﬁrm the

setting with the same process as the previous step.

6. After the last channel is conﬁrmed, power the transmitter OFF to save the

settings and exit trim programming. After conﬁrming all 7 channels with

button A, the system will automatically shut off.

During trim programming, the four green LEDs on the transmitter

will ﬂash to indicate which channel is selected for reversing

Channel 1

Throttle*

Channel 2

Aileron

Channel 3

Elevator

Channel 4

Rudder

To reverse the selected channel,

press the right vertical trim up

(Elevator trim for Mode 2). If

you don‘t want to reverse the

selected channel, proceed to

conﬁrming the direction.

To conﬁrm the direction for

the selected channel, press

and hold the A button. The

setting will be saved and the

next channel will be selected.

Repeat the process through

the ﬁrst four channels.

*Throttle Reversed Warning: The transmitter will emit a warning tone and display

ﬂashing LEDs upon reversing the throttle, after powering the transmitter OFF and

back ON. Press and hold the bind button/ switch A to accept and clear the throttle

reversed warning.

Factory Reset: Power the transmitter on while holding the sticks down and

outward. The transmitter will emit a series of beeps and revert to factory settings.

IMPORTANT: Factory reset will restore all settings to factory default, losing any

settings programmed in the DXS.

Channel 5 Channel 6 Channel 7

The RGB LED

indicates servo

direction;

green for normal,

red for reverse

SmartSafe

Hold Last

If loss of signal occurs, SmartSafe™

technology moves the throttle channel

to its preset failsafe position (low

throttle) that was set during binding.

All other channels hold their last

position. When the receiver detects

signal from the transmitter, normal

aircraft operation resumes.

Preset Failsafe

Preset failsafe is ideal for sailplanes,

allowing the aircraft to automatically

dethermalize if the signal is lost. With

preset failsafe, all channels go to their

preset failsafe positions if the signal is lost,

preventing a ﬂyaway. When the receiver

detects signal from the transmitter, normal

aircraft operation resumes.

SmartSafe

Hold Last

1 Lower the throttle on the transmitter

2 Push and hold the bind button on the AR410 and then power it ON

3 Release the button once the LED begins to ﬂash

4 Press the A button on the transmitter and power it ON.

Preset Failsafe

1 Move all sticks and switches on the DXS to the desired failsafe positions

2 Push and hold the bind button on the AR410 and then power it ON

3 Release the button once the LED begins to ﬂash

Push and Hold the Bind Button on the receiver during the rest of the bind process.

5 Press the A button on the transmitter and power it ON.

Setting Failsafe On The AR410 Receiver

The method of Failsafe and the Failsafe positions are set in the receiver during

binding. In the unlikely event that the radio link is lost during use, the receiver

will move all servo output signals to their pre-programmed failsafe positions.

If the power supply to the receiver drops below 3.5 volts during use, the

receiver will be unable to operate until the voltage recovers, and failsafe will

not work. That event would be called a brownout, and must be resolved in the

power supply to the receiver (BEC in the ESC, regulator, receiver battery, etc).

The AR410 Receiver may be set to either SmartSafe or Preset failsafe, as described below.

Smart Telemetry and LED Indicators on the DXS

Aircraft Battery Voltage: The four

green LEDs on the DXS transmitter

show the aircraft battery voltage

when using a Smart telemetry.

When paired with a Spektrum

Smart ESC and compatible receiver,

the aircraft battery voltage will be

displayed on the DXS transmitter’s

four LEDs. When in normal operation

with a Smart ESC, one LED will

illuminate for a low battery, two for

a half charged battery, three for a

battery between half and full, and

four for a fully charged ﬂight battery.

IMPORTANT: The four Green LEDs

on the transmitter do not indicate the

battery voltage of the AA batteries.

The DXS transmitter only indicates

the voltage of the AA batteries if they

are low and need to be replaced.

Low Battery Alarm:

The DXS

transmitter will emit a repeating

warning tone and the RGB LED will

ﬂash red if the AA batteries are below

approximately 4.7V.

LED Smart Battery Usage

LED Smart Battery voltage indication is based on current voltage and will change with

throttle/power usage. When throttle is increased, voltage drops, causing the bars to

indicate lower power (e.g., fewer LEDs solid or ﬂashing.) When the throttle is lowered

to idle/off, the bars recover (e.g., more LEDs solid or ﬂashing). LED bars will rise and

lower depending on throttle/power usage.

The Smart Battery low voltage alarm sounds when the ESCs are close to reaching low

voltage cutoff. The alarm will sound for 25 seconds. If the throttle is lowered to allow

voltage recovery, the alarm will stop early.

Land the aircraft when the alarm sounds.

After landing, reset the Smart Battery low voltage warning by either (1) powering

cycling the DXS transmitter, or (2) disconnecting the battery from the aircraft for more

than 15 seconds or until the LED voltage indication bars go out.

Connect a fully charged battery to the aircraft, which will ensure the Smart Battery low

voltage warning resets prior to the next ﬂight.

Wireless Trainer

The DXS transmitter is capable of operating as the Instructor transmitter

for a training situation. A remote receiver (SPM9747 optional, not included)

is required to add this function. When a student transmitter is bound to the

(optional) remote receiver inside the DXS, pressing and holding the A button

gives the student control.

Remote Receiver Installation:

1. Open the battery door

2. Connect the remote receiver cable

to the wireless trainer port.

3. Install the remote receiver in the

cavity behind the battery door with

double sided tape.

Binding the Student Transmitter:

1. Press and hold the bind button on

the remote receiver.

2. Power the DXS ON, the orange

LED on the remote receiver will

ﬂash indicating it is in bind mode.

Release the bind button.

3. Put the student transmitter into

Bind mode. The orange LED on the

remote receiver will remain lit when

it is bound to the student transmitter.

4. Replace the battery door after

binding the student transmitter.

Range Test

1. Power on the transmitter for at least ﬁve seconds with the throttle stick and trim low.

2. Press and hold switch A (Bind button) and toggle switch F four times within 10

seconds. The transmitter LEDs will ﬂash orange and the alarm will sound. The

system is in range check mode. Do not let go of the bind button until you are

ﬁnished with the range check.

IMPORTANT: You must hold the BIND/Panic button during the entire range check

process. Releasing the button will exit the range check mode.

Adjust Stick Tension

1. Disconnect the battery holder or optional battery from the transmitter and set aside.

2. Remove the six Phillips head screws that secure the rear transmitter case half.

3. Put the transmitter face down on a piece of foam or a towel and remove the rear case.

4. Tighten or loosen the screws (B) a small amount using a small Phillips screwdriver.

NOTICE: Always do a test of stick tension while turning these screws to

ensure stick tension is not too loose or too tight. Tightening a screw too much

can damage a spring. Loosening a screw too much can let a spring fall off

and cause short-circuit in the transmitter.

CAUTION: Always power off the transmitter, disconnect and remove

the battery before adjusting stick tension or friction straps. Not doing

so could result in property damage or injury.

Changing the Throttle Ratchet

1. Remove the batteries from the transmitter.

2. Remove the six Phillips head screws that secure the rear transmitter case half.

3. Put the transmitter face down on a piece of foam or a towel and remove the rear case.

NOTICE: Do not pull or disconnect any of the wires attached to the back

transmitter half or damage may result.

4. Locate the silver throttle friction straps (A) on both gimbals. One strap

engages a serrated section on the gimbal for a ratcheted throttle, while the

other strap engages the smooth section on the gimbal.

5. To change the throttle ratchet, loosen the throttle strap so it does not touch the throttle

gimbal. Tighten the opposite throttle strap to engage the desired throttle ratchet.

Troubleshooting Guide

Problem

Possible Cause Solution

Aircraft

will not

respond to

throttle but

responds

to other

controls

Throttle not at idle and/or throttle trim

too high

Reset controls with throttle stick and throttle

trim at lowest setting

Throttle servo travel is lower than 100%

Make sure throttle servo travel is 100%

or greater

Throttle channel is reversed

(With battery disconnected from aircraft) Reverse

throttle channel on transmitter

Motor disconnected from ESC Make sure motor is connected to the ESC

Aircraft

will not

Bind

(during

binding)

to trans-

mitter

Transmitter too near aircraft during

binding process

Move powered transmitter a few feet from

aircraft, disconnect and reconnect ﬂight

battery to aircraft

Aircraft or transmitter is too close to large

metal object, wireless source or another

transmitter

Move aircraft and transmitter to another

location and attempt binding again

The bind plug is not installed correctly in

the bind port

Install bind plug in bind port and bind the

aircraft to the transmitter

Flight battery/transmitter battery charge

is too low

Replace/recharge batteries

Bind button not held long enough during

bind process

Power off and repeat bind process.

Aircraft

will not

connect

(after

binding)

to trans-

mitter

Transmitter too near aircraft during

connecting process

Move powered transmitter a few feet

from aircraft, disconnect and reconnect

ﬂight battery to aircraft

Aircraft or transmitter is too close to

large metal object, wireless source or

another transmitter

Move aircraft and transmitter to another

location and attempt connecting again

Bind plug left installed in bind port

Rebind transmitter to the aircraft and remove

the bind plug before cycling power

Aircraft bound to different model

memory.

Select correct model memory on

transmitter

Flight battery/Transmitter battery

charge is too low

Replace/recharge batteries

Transmitter may have been bound

to a different aircraft using different

DSM protocol

Rebind aircraft to transmitter

Control

surface

does not

move

Control surface, control horn, linkage

or servo damage

Replace or repair damaged parts and

adjust controls

Wire damaged or connections loose

Perform a check of wires and connections,

connect or replace as needed

Transmitter is not bound correctly or

the incorrect model was selected

Rebind or select correct airplanes in

transmitter

Flight battery charge is low Fully recharge ﬂight battery

BEC (Battery Elimination Circuit) of the

ESC is damaged

Replace ESC

1-Year Limited Warranty

What this Warranty Covers - Horizon Hobby, LLC, (Horizon) warrants to the original

purchaser that the product purchased (the “Product”) will be free from defects in

materials and workmanship for a period of 1 year from the date of purchase.

What is Not Covered - This warranty is not transferable and does not cover

(i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse,

negligence, commercial use, or due to improper use, installation, operation or

maintenance, (iii) modiﬁcation of or to any part of the Product, (iv) attempted service

by anyone other than a Horizon Hobby authorized service center, (v) Product not

purchased from an authorized Horizon dealer, (vi) Product not compliant with applicable

technical regulations, or (vii) use that violates any applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER

WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL

IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED

WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY

ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE

REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy - Horizon’s sole obligation and purchaser’s sole and

exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii)

replace, any Product determined by Horizon to be defective. Horizon reserves

the right to inspect any and all Product(s) involved in a warranty claim. Service or

replacement decisions are at the sole discretion of Horizon. Proof of purchase is

required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER

THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability - HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,

INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR

COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED

IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER

THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual

price of the Product on which liability is asserted. As Horizon has no control over use,

setup, ﬁnal assembly, modiﬁcation or misuse, no liability shall be assumed nor accepted

for any resulting damage or injury. By the act of use, setup or assembly, the user

accepts all resulting liability. If you as the purchaser or user are not prepared to accept

the liability associated with the use of the Product, purchaser is advised to return the

Product immediately in new and unused condition to the place of purchase.

Law - These terms are governed by Illinois law (without regard to conﬂict of law

principals). This warranty gives you speciﬁc legal rights, and you may also have

other rights which vary from state to state. Horizon reserves the right to change or

modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services - Your local hobby store and/or place of

purchase cannot provide warranty support or service. Once assembly, setup or use

of the Product has been started, you must contact your local distributor or Horizon

directly. This will enable Horizon to better answer your questions and service you in

the event that you may need any assistance. For questions or assistance, please

visit our website at www.horizonhobby.com, submit a Product Support Inquiry at

https://horizonhobby.quickbase.com/db/bghj7ey8c?a=GenNewRecord, or call

the toll free telephone number referenced in the Warranty and Service Contact

Information section to speak with a Product Support representative.

Inspection or Services - If this Product needs to be inspected or serviced

and is compliant in the country you live and use the Product in, please use the

Horizon Online Service Request submission process found on our website or call

Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the

Product securely using a shipping carton. Please note that original boxes may

10/15

be included, but are not designed to withstand the rigors of shipping without

additional protection. Ship via a carrier that provides tracking and insurance for lost

or damaged parcels, as Horizon is not responsible for merchandise until it arrives

and is accepted at our facility. An Online Service Request is available at http://

www.horizonhobby.com/content/_service-center_render-service-center. If you do

not have internet access, please contact Horizon Product Support to obtain a RMA

number along with instructions for submitting your product for service. When calling

Horizon, you will be asked to provide your complete name, street address, email

address and phone number where you can be reached during business hours.

When sending product into Horizon, please include your RMA number, a list of the

included items, and a brief summary of the problem. A copy of your original sales

receipt must be included for warranty consideration. Be sure your name, address,

and RMA number are clearly written on the outside of the shipping carton.

Provided warranty conditions have been met, your Product will be serviced or replaced

free of charge. Service or replacement decisions are at the sole discretion of Horizon.

NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with

a LiPo battery, please contact the appropriate Horizon Product Support

ofﬁce. Warranty Requirements- For Warranty consideration, you must

include your original sales receipt verifying the proof-of-purchase date.

Non-Warranty Service - Should your service not be covered by warranty, service

will be completed and payment will be required without notiﬁcation or estimate

of the expense unless the expense exceeds 50% of the retail purchase cost. By

submitting the item for service you are agreeing to payment of the service without

notiﬁcation. Service estimates are available upon request. You must include this

request with your item submitted for service. Non-warranty service estimates will be

billed a minimum of ½ hour of labor. In addition you will be billed for return freight.

Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard,

American Express, and Discover cards. By submitting any item to Horizon for

service, you are agreeing to Horizon’s Terms and Conditions found on our website

http://www.horizonhobby.com/content/_service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the

country of use and ownership. If received, a non-compliant Product

will not be serviced. Further, the sender will be responsible for

arranging return shipment of the un-serviced Product, through a

carrier of the sender’s choice and at the sender’s expense. Horizon

will hold non-compliant Product for a period of 60 days from

notiﬁcation, after which it will be discarded.

Warranty and Service Contact Information

Country of

Purchase

Horizon Hobby Contact Information Address

United States

of America

Horizon Service Center

(Repairs and Repair Requests)

servicecenter.horizonhobby.com/

RequestForm/

2904 Research

Rd.

Champaign,

Illinois, 61822

USA

Horizon Product Support

(Product Technical Assistance)

productsupport@horizonhobby.com.

877-504-0233

Sales

websales@horizonhobby.com

800-338-4639

Horizon Technischer Service service@horizonhobby.eu

Hanskampring 9

D 22885

Barsbüttel,

Germany

Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100

Compliance Information for United States

FCC Information–

DXS Transmitter FCC ID: BRWKATY1T

AR410 Receiver FCC ID: BRWTASPMAR410

NOTICE: Modiﬁcations to this product will void the user’s authority to

operate this equipment.

This product contains a radio transmitter with wireless technology which

has been tested and found to be compliant with the applicable regulations

governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.

When operating your Spektrum receiver, please be sure to maintain a

separation distance of at least 20 cm between your body (excluding ﬁngers,

hands, wrists, ankles and feet) and the antenna to meet RF exposure safety

requirements as determined by FCC regulations.

Supplier’s Declaration of Conformity

Spektrum DXS Transmitter and AR410 4-CH Receiver: SPM1010

Spektrum DXS Transmitter only: SPMR1010

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

CAUTION: Changes or modiﬁcations not expressly approved by the

party responsible for compliance could void the user’s authority to

operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Horizon Hobby, LLC

2904 Research Rd.,

Champaign, IL 61822

Email: compliance@horizonhobby.com

Web: HorizonHobby.com

Horizon Hobby, LLC hereby declares that this product is in compliance with

the essential requirements and other relevant provisions of the RED Directive.

A copy of the EU Declaration of Conformity is available online at:

http://www.horizonhobby.com/content/support-render-compliance.

Frequency Band: 2402 - 2478 MHz

Max EIRP: 20dBm

Instructions for Disposal of WEEE by Users in the European Union

This product must not be disposed of with other waste. Instead, it is the

user’sresponsibility to dispose of their waste equipment by handing it over

to adesignated collection point for the recycling of waste electrical and elec-

tronic equipment. The separate collection and recycling of your waste equipment at the

time of disposal will help to conserve natural resources and ensure that it is recycled in

amanner that protects human health and the environment. For more information about

where you can drop off your waste equipment for recycling, please contact your local

city ofﬁce, your household waste disposal service or where you purchased the product.

Compliance Information for the European Union

IC Information

DXS Transmitter IC: 6157A-KATY1T

AR410 Receiver IC: 6157A-TASPMAR410

CAN ICES-3 (B)/NMB-3(B)

This device complies with ISED Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, Including

interference that may cause undesired operation of the device.

Compliance Information for Canada

DSM, DSM2, DSMX, Spektrum Airware, SRXL2, SmartSafe, Hangar 9 and the Horizon Hobby

logo are trademarks or registered trademarks of Horizon Hobby, LLC.

The Spektrum trademark is used with permission of Bachmann Industries, Inc.

JR is a registered trademark of JR Americas. All other trademarks, service marks and logos

are property of their respective owners.

US 7,391,320. US 9,056,667. US 9,753,457. US 9,930,567. US 10,078,329. US 10,419,970.

59922.3

Created 06/20 SPM1010, SPMR1010

Spektrum DXS Transmitter Only Owner's manual

Brand: Spektrum

Model: DXS Transmitter Only

Category: Toys & accessories

Type: Owner's manual

Download PDF

report

Spektrum DXS Transmitter Only Owner's manual

Spektrum DXS Transmitter Only Owner's manual

Related papers

Other documents