AVENTICS LS04 SW Assembly Instructions

Page is loading ...

2 “For your safety”, befor

e assembling the LS04 SW

valve system.

Related documents

The LS04 SW valve system is a single component. Also

follow the instructions for the other system components.

Further information on the valve system can be found in

the AVENTICS online catalog at

www.aventics.com/pneumatics-catalog.

Abbreviations used

2For your safety

The VS LS04 SW has been manufactured according to the

accepted rules of safety and current technology. There is,

however, still a danger of personal injury or damage to

equipment if the following general safety instructions and

the warnings before the steps contained in these

instructions are not complied with.

O Read these instructions thoroughly and completely

before assembling the VS LS04 SW.

O Keep these instructions in a location where they are

accessible to all users at all times.

O Always include the assembly instructions when you

pass the VS LS04 SW on to third parties.

Intended use

The VS LS04 SW is a pneumatic valve system with

electrical control. With the VS LS04 SW you can distribute

stored pressure energy to your system components in a

targeted manner by controlling various devices (e.g.

pneumatic cylinders).

O Only use the VS LS04 SW

for the purpose for which it

was designed

.

O The VS LS04 SW

is only intended for industrial

applications.

O Observe the performance limits listed in the technical

data (see “Technical data” on page 1).

Intended use includes having read and understood these

instructions, especially the chapter “For your safety”.

Abbreviation Meaning

VS Valve system

SW Single Wiring (single-wire connection)

Improper use

It is considered improper use

W when the VS LS04 SW is used for any application not

named in these instructions and

W is used under operating conditions that deviate from

those described in these instructions.

Personnel qualifications

Assembly requires basic pneumatic knowledge, as well as

knowledge of the appropriate technical terms. Assembly

may therefore only be carried out by qualified pneumatic

personnel or an instructed person under the direction and

supervision of qualified personnel.

Qualified personnel are those who can recognize possible

hazards and institute the appropriate safety measures

due to their professional training, knowledge, and

experience as well as their understanding of the relevant

conditions pertaining to the work to be done. Qualified

personnel must observe the rules relevant to the subject

area.

General safety instructions

W Observe the regulations for accident prevention and

environmental protection for the country where the

device is used and at the workplace.

W Do not change or modify the VS LS04 SW.

W Only use the VS LS04 SW within the performance

range provided in the technical data.

W Do not place any mechanical loads on the VS LS04 SW

under any circumstances.

W Make sure that all relevant system parts are not under

pressure or voltage before you assemble the

VS LS04 SW.

W Ensure that all connections of the VS LS04 SW are

correctly carried out.

W If these systems are to be used in environments with

high concentrations of SO

2

, be sure to contact your

nearest AVENTICS sales office.

W Dispose of the VS LS04 SW in accordance with the

applicable national regulations.

3 Delivery contents/device

description

The following is included in the delivery contents (see ):

W LS04 SW series VS valve (5) with seals (7) and cover (6)

W LS04 series blanking plate (2) with seals

W LS04 partition/supply plate (3) with seals

W End plate kit with subbase (1), end plate (8), tie rod

mounting screws (9) with washers

Please refer to the AVENTICS accessories program for

additional information on optionally available accessories.

1

AVENTICS | LS04 SW | R412009675–BAL–001–AD | English

English

1 About this document

These instructions contain important information on the

safe and appropriate assembly of the LS04 S

W valve

system.

O Read these instructions completely, especially chapter

5

4 Assembly

Assembling the valve system

3. Insert both tie rods (12, 13) with the torsion protection

into the subbase (1).

4. Insert the tie rod mounting screws (9) with washers

into the subbase (1) and tighten them slightly.

5. Insert the valve plate first into the upper tie rod and

then tilt it downward until it engages in the lower tie

rod.

6. Slide the valve plate on the tie rods toward the subbase

until the valve plate engages in place.

7. Proceed in the same manner with the following valve

plates, making sure that they also engage in the

previously installed valve plate.

8. Install the end plate (8) on the tie rods (12, 13) and then

insert the tie rod mounting screws (9).

9. Tighten the tie rod mounting screws (9) on the subbase

(1) and the end plate (8) evenly

(tightening torque = 1,3

r 0,1

Nm).

Exchanging the valve plates,

occupying reserve positions

1. Loosen the tie rod mounting screws (9) on the subbase

(1) and the end plate (8) by several turns.

2. Pull apart the valve plates (5) or blanking plates (2) at

the desired location. Please note during removal that

the centering pins on both sides of the valve plates and

blanking plates must be exposed.

3. Remove the valve plate (5) or blanking plate (2) by

rotating it around the upper tie rod (13). The cover

element (6) can then be loosened from the valve plate

by applying light pressure, and the cover will remain in

the VS.

4. Insert the new valve plate into the upper tie rod (13)

and tilt the valve plate downward. The valve plate must

engage in the lower tie rod (12) as well as in the cover

element (6).

5. Slide the valve plates (5) or blanking plates (2) back

together.

CAUTION

System is operating under pressure

Working on the system when under pressure could lead

to injuries and damage!

O Depressurize all relevant system parts before

working on the system.

If blanking plates or partition/supply plates are to

be used, the covers (available separately) must be

installed so that they engage in the previously

installed valve plates. After this, the blanking plate

or partition/supply plate can be installed.

1

6. Tighten the tie rod mounting screws (9) on the subbase

(1) and the end plate (8) evenly

(tightening torque = 1,3

r 0,1

Nm).

Expanding the valve system

1. Loosen and remove the tie rod mounting screws (9) on

the end plate (8).

2. Remove the end plate (8).

3. Screw the tie rod extensions (4) into the tie rods (12,

13) until flush (tightening torque = 1,3

r 0,1

Nm).

4. Insert the valve plate into the upper tie rod (13) and

then tilt it downward until it engages in the lower tie

rod (12).

5. Slide the valve plate on the tie rods toward the subbase

until the valve plate engages in the previous valve

plate.

6. Install the end plate (8).

7. Insert the tie rod mounting screws (9) with washers

into the end plate (8) and tighten them evenly

(tightening torque = 1,3

r 0,1

Nm).

5 Electrical connection

Each valve can be directly wired in the VS LS04 SW. This

is done by inserting the stripped cable ends into the spring

clamps on the rear of the VS.

Stripping the cable ends

O Strip the cable ends as shown in .

CAUTION

O Take precautions against overvoltages in signal-

carrying lines that are longer than 30 m.

NOTICE

O During each valve sequence, only one neutral wire

has to come into contact with any of the valves. Any

contact with additional valve plates occurs

internally.

O For the VS LS04 SW with an operating voltage of

12 V DC, limit the maximum number of solenoids per

neutral connection to 20.

Connection cable

Individual strands Multiple strands

A Ø 0.4 mm – 0.8 mm

26 AWG – 20 AWG

0.2 mm

2

– 0.5 mm

2

24 AWG – 20 AWG

B 9 r0.5 mm

1

2

AVENTICS | LS04 SW | R412009675–BAL–00

1–AD | English

6

Establishing the electrical connection

1. Open the spring clamp by lightly pressing and holding

down the button, and insert the stripped end of the wire

into the clamp.

Note the markings identifying the connections for

solenoids 12, 14 and 0.

2. Release the button.

The cable end is now secured by the clamp spring

force and the electrical connection is complete.

Breaking the internal contacts

The neutral wires for the valve plates are connected

internally. This connection can be interrupted to obtain

neutral sections that are independent of each other.

How to break the internal contacts:

1. Remove the valve plate where the interruption should

start (see “Assembly” on page 2).

2. Break off the contact lug (see ).

3. Replace the valve plate.

6 Maintenance

The P-assembly strip is maintenance-free. Please contact

the service department at AVENTICS if you have any

technical problems.

7 Cleaning and servicing

How to clean the VS LS04 SW:

1. Make sure that all relevant system parts are not under

voltage or pressure.

2. Clean the VS LS04 SW with a damp cloth. Only use

water or a mild cleaning agent.

8Disposal

O Dispose of the VS LS04 SW in accordance with the

applicable national regulations.

Blanking, partition and supply plates break the

internal contacts.

CAUTION

Damage to the surface caused by solvents and

aggressive detergents

The surfaces and seals could be damaged by

aggressive solvents and cleaning agents.

O Never use solvents or aggressive detergents.

3

4

9 Technical data

General

Pneumatic

connections

Push-in fitting for plastic tubing with

external Ø:

1, 3/5: 10 mm (3/8"), 2, 4: 4 mm (1/8") or

6 mm (1/4")

X (external pilot control air): 6 mm (1/4")

R (restricted pilot exhaust air): 6 mm

(1/4")

Internal or

external pilot

control

Via different end plates,

connection X closed with internal pilot

control

Stages of

expansion

2 to 24 valve stations for 2 to 24 valve

solenoids

Mounting

orientation

Any

Ambient

temperature

–10 °C to +50 °C

Pneumatics

Medium Compressed air in accordance with ISO

8573-1:2010.

Max. particle size 5 μm, the pressure

dew point must be at least 15

°

C under

ambient and medium temperature and

may not exceed 3

°

C, oil content 0 mg/

m

3

– 5 mg/m

3

.

(oil: OL 1413-068, AVENTICS no.

5 962 260 000, trade name per

AVENTICS standard N28, Volume 8:

Shell Oil 4007)

Medium

temperature

–10 °C to +50 °C

Nominal flow 320 l/min at 6 to 5 bar

Working

pressure

–0.9 to 8 bar

Control

pressure

range

3 to 8 bar

Electrics for solenoid coils

Rated

solenoid

voltage

24 VDC (r10%)

from a power pack with safe isolation

according to DIN EN 60742,

classification VDE 0551

Power

consumption

per solenoid

0.7 W incl. LED and protective circuit

Operating

mode

according to

VDE 0580

Continuous operation (S1)

AVENTICS | LS04 SW | R4120096

75–BAL–001–AD | English

7

VS electrics

Max. current

per valve

control

28 mA (at 24 V and 10%)

48 mA (at 12 V and 10%)

Max. current

GND total

1 A

Protection

class

according to

EN 60 529/

IEC 529

IP20

AVENTICS | LS04 SW | R

412009675–BAL–001–AD | English

8

Page is loading ...

1

3

9

10

11

12

13

2

7

6

8

5

4

Elektrischer Anschluss

Electrical connection

Raccordement électrique

Kabelenden abisolieren

Stripping the cable ends

Isoler des jonctions de câble

Kontaktierung unterbrechen

Interrupting the contacts

Interrompre le contact électrique

Lieferumfang und Übersicht

Delivery contents and overview

Fourniture et vue d’ensemble

A

B

2

1

2

3

1

4

Page is loading ...

The data specified above only serve to

describe the product. No statements

concerning a certain condition or

suitability for a certain application can

be derived from our information. The

given information does not release the

user from the obligation of own

judgement and verification. It must be

remembered that our products are

subject to a natural process of wear

and aging.

An example configuration is depicted

on the title page. The delivered

product may thus vary from

that in the

illustration.

Translation of the original operating

instructions. The original operating

instructions were created in the

German language.

R412009675–BAL–001–AD/03.2016

reserved by AVENTICS GmbH, even

and especially in cases of proprietary

rights applications. It may not be

reproduced or given to third parties

without its consent.

AVENTICS GmbH

Ulmer Straße 4

30880 Laatzen, GERMANY

Phone +49 (0) 5 11-21 36-0

Fax: +49 (0) 511-21 36-2 69

www.aventics.com

[email protected]

AVENTICS LS04 SW Assembly Instructions

This manual is also suitable for

AVENTICS LS04 SW Assembly Instructions

in other languages

Related papers

Other documents