Panasonic BLPA100KT Operating instructions

BL-PA100KT

English Français Deutsch Italiano Español Português Ё᭛

䚐ạ㛨

Русский

Getting Started

Prise en main

Erste Schritte

Guida introduttiva

Primeros pasos

Iniciação

ܹ䮼ᣛफ

Начало работы

㇠㟝

G㉘⮹㉐

㉘⮹㉐

KK0606CH0

PQQX15025ZA

Getting Started

HD-PLC Ethernet Adaptor Starter Pack

Power Line Communication

Model No.

BL-PA100KT

Included items

HD-PLC Ethernet Adaptor (x2)

One adaptor is pre-configured as the

"master" adaptor, as indicated by the

MASTER seal affixed to the top of the

adaptor. The other adaptor is pre-

configured as the "terminal" adaptor.

Example of an integrated HD-PLC network

AC Cord (x2)

Order no.: PSJA1106Z

Connects each adaptor to the wall outlet.

- Getting Started (this document)

- Important Information

- CD-ROM

INTERNET

Master

PC

Network printer

Wall outlet

Hub

Network camera

Modem

Router

PC

Terminal

(Add-on adaptor)

This document is written to be used with the BL-PA100KT,

which is a pre-configured set of 2 adaptors.

No settings are required to use these adaptors.

Simply follow the instructions provided in this document.

Refer to the included Important Information document for

safety and other information. Refer to the Operating

Instructions (found on the CD-ROM) for reconfiguration and

troubleshooting information.

Set of 2 Adaptors (Master and Terminal)

Additional adaptors can be added later, for a total of 16 adaptors including the master.

See the Operating Instructions (found on the CD-ROM) for details.

English

1

Connect the master adaptor (indicated by the

MASTER seal) to the wall outlet using the

included AC cord.

For best results

We recommend connecting the adaptors directly to a wall outlet. Avoid connecting high power-consuming appliances to the same

wall outlet. Additionally, connecting an adaptor to a uninterruptible power supply (UPS) or backup power supply device is not

recommended.

While connecting the adaptors to a wall outlet is recommended, keep the following in mind if you must connect an adaptor to a

power strip:

- Make sure the power strip does not a have a noise filter or a surge protector, as these features may interfere with the

performance of your adaptors.

- Do not connect the adaptor to a power strip that receives power from another power strip.

- Use a power strip with an AC cord that is as short as possible.

For more information, refer to the included Operating Instructions (found on the CD-ROM).

Installation

2

Connect the master adaptor to a network device

using a LAN cable (sold separately). We

recommend connecting the master to your router.

3

Connect the terminal adaptor to the wall outlet

using the included AC cord.

4

Connect the terminal adaptor to a network

device, such as your PC, using a LAN cable (sold

separately).

5

Confirm that the indicators on the master adaptor

are lit (not flashing) as shown.

6

Confirm that the indicators on the terminal

adaptor are lit (not flashing) as shown.

If the indicators are not lit as shown above, confirm all

connections and refer to the Troubleshooting section of the

Operating Instructions.

If the indicators are not lit as shown above, confirm all

connections and refer to the Troubleshooting section of the

Operating Instructions.

To wall outlet

PLC (blue)

LAN (green)

MASTER (green)

Router

PLC (blue)

LAN (green)

MASTER (off)

To wall outlet

Page is loading ...

The information in this document is subject to change without notice.

2006

Panasonic Communications

Copyright:

This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced

for internal use only. All other reproduction, in whole or in part, is prohibited without the written

consent of Panasonic Communications Co., Ltd.

Panasonic Communications Co., Ltd.

1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan

Panasonic BLPA100KT Operating instructions

Panasonic BLPA100KT Operating instructions

in other languages

Related papers

Other documents