Aeg-Electrolux USR200 User manual

Page is loading ...

2

K

A

B

D

C

E

F

G

H

J

1

Gerätebeschreibung

A Scheibenmesser gezahnt (Rundmesser)

B Messerverschluß mit Linksdrehung

C Schneidgutschlitten mit Fingerschutz

D Restguthalter

E Anschlagplatte

F Schneidetisch mit Schlittenführungsrille

G Typenschild (Geräteunterseite)

H Schnittstärke-Einstellrad

J Schnittstärke-Einstellskala

K Ein-/Ausschalter

Appliance Description

A Toothed Cutting Disc (Circular Blade)

B Blade Lock with Left-Hand Thread

C Slide with Finger Protection

D Holder

E Stop Plate

F Slicing Table with Guide Slot for the Slide

G Rating Plate (on the underside of the

appliance)

H Slice Thickness Adjustment Knob

J Slice Thickness Adjustment Scale

K On/Off Switch

822_949_017 USR200.book Seite 2 Mittwoch, 22. Februar 2006 3:08 15

3

4

5

2

3

6

7

822_949_017 USR200.book Seite 3 Mittwoch, 22. Februar 2006 3:08 15

4

8

9

10

822_949_017 USR200.book Seite 4 Mittwoch, 22. Februar 2006 3:08 15

Page is loading ...

g

9

g

Dear Customer,

Please read these operating instruc-

tions carefully. Above all please

observe the safety instructions on the

first few pages of these operating

instructions! Please keep these operat-

ing instructions for later reference. Pass

them on to any subsequent owner of

the appliance.

1 Safety Instructions

• Prior to using for the first time, please

note that the appliance may only be

used with the voltage and type of cur-

rent that is stated on the rating plate.

• Only connect the appliance to a socket

that has been installed in accordance

with regulations.

• Do not hold any hard objects against

the rotating blade, and do not reach

into the blade. There is a risk of injury!

• Plastic parts must not be placed on or

close to radiators.

• The Universal Slicer is a household

appliance and therefore not suitable

for commercial use.

• The Universal Slicer may only be used

once it has been positioned in accor-

dance with instructions.

• Under no circumstances should the

Universal Slicer be used to slice frozen

food.

(There is a risk of damage to the appli-

ance.)

• It is essential that the slide be used

(Fig. 1/C) when slicing. The slide and

holder (Fig. 1/D) may only be removed

in the case that the size and shape of

the item to be sliced is such as to pre-

vent their use (e.g. bread).

• Switch off the appliance after a maxi-

mum of 5 minutes continuous use, the

Universal Slicer is designed for a maxi-

mum period of operation of 5 minutes.

• After each use, return the stop plate

(Fig. 1/E) to the „0” position to avoid

anybody injuring themselves on the

circular blade (Fig. 1/A).

• Prior to cleaning and before changing

the blade, put the stop plate in the „0”

position and unplug the appliance

from the mains.

• Never submerge the appliance in water

or otherwise bring it into contact with

water. Observe the cleaning instruc-

tions!

Important:

• After switching off the appliance,

the circular blade continues to

rotate for a short time.

• Children do not recognise the haz-

ards that can be present when using

electrical appliances or slicers. For

this reason do not leave children to

„play” or use the appliance unsuper-

vised. Do not leave the appliance

running unsupervised.

• In order to avoid danger, if the con-

nection lead of this appliance is

damaged, it must be replaced by the

manufacturer, its customer service

department or a similarly qualified

person.

• Repairs to this appliance may only

be carried out by qualified service

engineers. Considerable danger may

result from improper repairs. If

repairs become necessary, please

contact the Customer Care Depart-

ment or your authorised dealer.

• If the appliance is used for a purpose

other than that intended, or is ope-

rated incorrectly, no liability can be

accepted.

;

This appliance complies with the fol-

lowing EC directives:

• 73/23/EWG dated 19.2.1973

„Low Voltage Directive", including

Directive Amendment 93/68/EWG.

• 89/336/EWG dated 3.5.1989

„EMC Directive”, including Directive

Amendment 92/31/EWG.

822_949_017 USR200.book Seite 9 Mittwoch, 22. Februar 2006 3:08 15

g

10

Positioning the Appliance

The Universal Slicer, with its non-slip

feet, will stand securely without slip-

ping on level, clean, dry work surfaces.

Prior to using for the first time, it is

advisable to wipe all parts with a damp

cloth and dry them.

Prior to Using

• Check that the appliance is stable and

connect to the mains using the mains

plug.

• Set the required slice thickness. To do

this, turn the slice thickness adjust-

ment knob (Fig. 2) anticlockwise. Slice

thicknesses from thin to approx.

14 mm can be selected continuously.

The slice thickness adjustment scale

(Fig. 1/J) is not graduated in millime-

tres, it is an arbitrary scale for your ref-

erence. The „0” position is designed to

cover the blade for safety reasons.

• Assemble the slide (Fig. 3). Lift up the

rear wall of the slide until it is at 90º

and then press downwards to the stop.

• Fold down the slicing table.

• Fitting the slide and the holder.

Tilt the slide (Fig. 4) and place in the

guide slot on the side of the slicing

table, swivel into the working position.

Place the holder on the slide from the

right.

Switching On the Universal Slicer

The Universal Slicer is switched on by

applying thumb pressure to the switch

(Fig. 1/K). At the same time the safety

interlock must be disengaged with

another finger (Fig. 5). The circular

blade continues to rotate as long as

the switch remains pressed. When the

switch is released, the appliance

switches off.

Please Note: The circular blade contin-

ues to rotate for a short time after the

appliance is switched off.

After each use, please return the stop

plate to its initial position („0“ posi-

tion) by turning the slice thickness

adjustment knob (Fig. 2).

Instructions for Use

To use the Universal Slicer safely and

ensure even slicing, place the item to

be sliced on the slide and press it, if

necessary using the holder, lightly

against the stop plate (Fig. 6). With the

circular blade rotating, the slide is then

moved, together with the item to be

sliced, towards the circular blade, apply

light pressure. After use, return the

stop plate to the „0” position using the

slice thickness adjuster.

Collecting the Slices

Place, for example, a plate in the cut-

out in the housing (Fig. 7).

Removing the Circular Blade

Prior to removing the circular blade, it

is imperative that the stop plate be

placed in the „0” position and that the

appliance is unplugged from the mains.

When carrying out the following steps,

please do not forget: The circular

blade is very sharp!

Unscrew the blade lock (Fig. 8) by turn-

ing it clockwise (left hand thread).

The circular blade can now be removed

from the housing cover.

Fitting the Circular Blade

Place the circular blade in the housing

cover, rotating it slightly if necessary.

The blade must be positioned in the

recess in the housing cover over its

entire periphery. Fit the blade lock by

turning it in an anticlockwise direction

(turn to the left). Tighten the blade

lock.

822_949_017 USR200.book Seite 10 Mittwoch, 22. Februar 2006 3:08 15

g

11

Dismantling the Appliance

(Fig. 9/10)

Remove the circular blade as described

above. To remove the slicing table, fold

it up and pull it out of the housing at

the lower end at the rear (Fig. 9). To

replace the slicing table, position it

vertically and insert the two pins at the

front, followed by those at the rear. To

remove the motor unit, the circular

blade must be removed first. Unlock

the motor unit and then pull it out of

the housing to the front by the handle

(Fig. 10). To replace the unit, slide it in

until it audibly engages in the housing.

Cleaning

With the exception of the motor unit

with the mains cable, your appliance is

dishwasher safe. Cleaning is only to be

performed when the circular blade is

stationary. Prior to cleaning, it is

imperative that the stop plate be

placed in the „0” position and that the

appliance is unplugged from the mains.

Clean the motor unit with a damp

cloth. The remaining parts can be

washed normally in water by hand or

placed in the dishwasher at max. 50 °C.

Never stand or submerge the Univer-

sal Slicer in water.

Putting the Appliance Away

Remove the holder and the slide; fold

the slide together. Fold up the slicing

table. Your appliance will now fit in a

drawer with a minimum height of

125 mm (internal dimension).

Disposal

2

Packaging material

The packaging materials are environ-

mentally friendly and can be recycled.

The plastic components are identified

by markings, e.g. >PE<, >PS<, etc.

Please dispose of the packaging mate-

rials in the appropriate container at

the community waste disposal faci-

lities.

2

Old appliance

The symbol

W on the product or on

its packaging indicates that this pro-

duct may not be treated as household

waste. Instead it shall be handed over

to the applicable collection point for

the recycling of electrical and electro-

nic equipment. By ensuring this pro-

duct is disposed of correctly, you will

help prevent potential negative conse-

quences for the environment and

human health, which could otherwise

be caused by inappropriate waste

handling of this product. For more

detailed information about recycling

of this product, please contact your

local city office, your household waste

disposal service or the shop where you

purchased the product.

822_949_017 USR200.book Seite 11 Mittwoch, 22. Februar 2006 3:08 15

Page is loading ...

43

822_949_017 USR200.book Seite 43 Mittwoch, 22. Februar 2006 3:08 15

Electrolux Hausgeräte Vertriebs GmbH

Muggenhofer Str. 135

D-90429 Nürnberg

http://www.electrolux.de

822 949 017 – 03 - 0206

822_949_017 USR200.book Seite 44 Mittwoch, 22. Februar 2006 3:08 15

Aeg-Electrolux USR200 User manual

Aeg-Electrolux USR200 User manual

in other languages

Related papers

Other documents