Pulsar SF108 Quick start guide

Category
Network switches
Type
Quick start guide

This manual is also suitable for

Pulsar SF108 is a 10-port PoE switch designed to power IP cameras compliant with the IEEE 802.3af standard. It features 8 PoE ports with a power budget of 15.4W each, 1 uplink port (G1/TP), and 2 uplink ports (G1/SFP, G2/SFP) for fiber optic transmission. The switch supports auto-learning and auto-aging of MAC addresses (1K size) and provides LED indication for power, PoE status, and link activity. It comes with a 48VDC/2.5A/120W max power supply and includes additional assembly elements.

Pulsar SF108 is a 10-port PoE switch designed to power IP cameras compliant with the IEEE 802.3af standard. It features 8 PoE ports with a power budget of 15.4W each, 1 uplink port (G1/TP), and 2 uplink ports (G1/SFP, G2/SFP) for fiber optic transmission. The switch supports auto-learning and auto-aging of MAC addresses (1K size) and provides LED indication for power, PoE status, and link activity. It comes with a 48VDC/2.5A/120W max power supply and includes additional assembly elements.

1
SF108
v1.0
SF108 10-port switch for 8 IP cameras
Edition: 1 from 1.10.2016
Supercedes the edition: -------------
EN
Features:
Switch 10 ports
8 PoE ports 10/100Mb/s, (1÷8 ports) (data and power
supply)
1 port 10/100/1000 Mb/s (G1/TP port) (UpLink)
2 ports 10/100/1000Mb/s SFP (porty G1/SFP, G2/SFP)
15,4W for each PoE port, supports devices complaint
with the IEEE802.3af standard
Supports auto-learning and auto-aging of MAC
addresses (1K size)
LED indication
The PSD 480250 48VDC/2,5A/120W max.
power supply desktop type included
Additional assembly elements
warranty 2 year from the production date
Example of use.
1. Technical description.
1.1. General description.
SF108 is a 10- port PoE switch designed to supply IP cameras operating in IEEE 802.3af standard.
Automatic detection of any devices powered in the PoE standard is enabled at the 1 8 ports of the switch. The G1/TP ports is
used for connection of another network device via RJ45 connector. The switch is fitted with SFP slots; the use of fiber optic
module (GBIC) allows fiber optic transmission.
The operating status of the device (described in the table below) is displayed on the LED display on the front panel.The PoE
technology ensures a network connection and reduces installation costs by eliminating the need to supply a separate power
cable for each device. This method allows supplying other network devices, such as IP phone, wireless access point or router.
2
1.2. Block diagram.
Fig. 1. Block diagram.
1.3. Description of components and connectors.
Table 1. (see Fig. 2)
Element no.
(Fig. 2)
Description
[1]
8 x PoE port (1÷8)
[2]
1 x UPLINK port (G1/TP)
[3]
2 x UPLINK port (G1/SFP, G2/SFP)
[4]
Power Socket of the 48VDC
Fig. 2 The view switch'a.
3
1.4. Technical parameters (table 2.)
Table 2.
Ports
8 x PoE (10/100Mb/s) (RJ-45)
1 x UPLINK (10/100/1000Mb/s) (RJ-45)
2 x UPLINK (10/100/1000Mb/s) (SFP)
with connection speed auto-negotiation and MDI/MDIX Auto Cross)
PoE power supply
IEEE 802.3af (1÷8 ports), 48VDC / 15,4W at each port *
Used pairs 4/5 (+), 7/8 (-)
Protocols, Standards
IEEE802.3, 802.3u, 802.3x CSMA/CD, TCP/IP
Forwarding rate
10BASE-T: 14880pps/port
100BASE-TX: 148800pps/port
Bandwidth
1,6Gbps
Transmission method
Store-and-Forward
Optical indication of
operation
Switch power supply
Link
PoE Status
Power supply
90 ÷ 264VAC 50÷60Hz / 0,6A 230VAC max.
the PSD 480250 48VDC/2,5A/120W max. power supply desktop type
Operating conditions
temperature -10°C ÷ 45°C,
relative humidity 20% - 90%, no condensation
Dimensions (W x H x D)
220 x 44 x 150 [mm]
Additional equipment
plate to be fixed surface, bracket for Rack 19”
Net/gross weight
1,73/1,97kg
Protection class
EN 60950-1:2007
I (first)
Storage temperatur
-20°C ÷ 60°C
Declarations
CE
* The given value of 15,4W per port is the maximum value. The total power consumption should not exceed 96W when all PoE ports are being used.
2. Installation.
2.1. Requirements.
The unit should be mounted in confined spaces, in accordance with the 2nd environmental class, with normal
relative humidity (RH=90% maximum, without condensation) and temperature from -10°C to +45°C. Ensure the free flow
of air around the unit. The PSU shall work in a vertical position that guarantees sufficient convectional air-flow through
ventilating holes of the enclosure.
The switch load balance should be done before installation. The given value of 15,4W per port is the maximum value
referring to a single output. The total power consumption should not exceed 96W when all PoE ports are being used. The
increased demand for power is particularly evident in the case of cameras with heaters or infrared illuminators - when
launching these features, the power consumption increases rapidly, which may adversely affect the operation of the
switch. As the device is designed for a continuous operation and is not equipped with a power-switch, therefore an appropriate
overload protection in the power supply circuit should be provided. The electrical system shall be made in accordance with
applicable standards and regulations.
2.2. Installation procedure.
1. Connect switch to the PSD480250 48VDC power supply unit desktop type.
2. Connect the power supply to the AC 230V socket.
3. Connect the camera wires to the RJ45 connectors (PoE connectors (sockets RJ45 from 1 to 8)).
4. Connect the remaining LAN devices to RJ45 connectors (G1/TP or G1/G2 and SFP/SFP)
CAUTION! G1/TP and G1/SFP connectors can not operate simultaneously
5. Check the optical indication of switch operation (see Table 3).
4
Connection schemes
3. Operation indication (see table 3)
Table 3. Operation indication
GREEN LED LIGHT (Power)
Indication of the switch's power
supply
OFF no power supply of the switch
ON power supply on, normal operation
DIODA LED ZIELONA (PoE)
Indication of the PoE power supply
at the RJ45 ports
OFF- no power supply at the RJ45 port (the device is not connected or not compliant with
the IEEE802.3af standard)
ON supply
Blinking short-circuit or output overload
YELLOW LED LIGHT (LINK)
The connection status of LAN
devices, 10MB/s or 100Mb/s
and data transmission
OFF- no connection
ON - the device is connected; 10Mb/s or 100Mb/s
Blinking data transmission
OPTICAL INDICATION AT THE UPLINK PORT (G1/TP, G1/SFP, G2/SFP)
GREEN LED LIGHT
No light (OFF) - no connection or LAN device is not connected
ON - the LAN device is connected
Blinking data transmission
CAUTION! Do not connect the device even if the slot is empty
CAUTION! G1/TP and G1/SFP sockets can not operate simultaneously
5
WEEE LABEL
Waste electrical and electronic equipment must not be disposed of with normal household waste.
According to the European Union WEEE Directive, waste electrical and electronic equipment
should be disposed of separately from normal household waste.
GENERAL WARRANTY CONDITIONS
1. Pulsar (manufacturer) grants a two-year quality warranty for the equipment, starting from the production date.
2. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (selected by the manufacturer) if the
malfunction is due to the manufacturer. It includes manufacturing or material defects, provided that such defects have been
reported within the warranty period (point.1).
3. The equipment subjected to warranty should be brought to the place of purchase or directly to the main office of the
manufacturer.
4. The warranty applies to complete equipment, accompanied by a properly filled warranty claim with a description of the defect.
5. Should the claim be accepted, the manufacturer is obliged to provide warranty repairs, at the earliest convenience, however not
later that within 14 days from the delivery to the service centre of the manufacturer.
6. The repair period mentioned in point 5 may be prolonged, if there are no technical possibilities to carry out the repairs, or if the
equipment has been conditionally accepted, due to the breaking warranty terms by the claimant.
7. All the services are carried out at the service centre of the manufacturer, exclusively.
8. The warranty does not cover the defects of the equipment, resulting from:
- reasons beyond the manufacturer's control,
- mechanical damage,
- improper storage and transport,
- use that violates the operation manual or equipment’s intended use
- fortuitous events, including lightning discharges, power failures, fire, flood, high temperatures and chemical agents,
- improper installation and configuration (failure to follow instruction).
9. The warranty is void in case of construction changes and repairs carried out by any unauthorized service center or in case of
damage or modifications to warranty stickers and serial numbers.
10. The liability of the manufacturer towards the buyer is limited to the value of the equipment determined according to the
wholesale prices suggested by the manufacturer on the day of purchase.
11. The manufacturer takes no responsibility for the defects that result from the damaging, malfunctioning or inability to operate
the equipment especially when resulting from failure to comply with the recommendations and requirements contained in the
manual.
Pulsar
Siedlec 150, 32-744 Łapczyca, Poland
Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50
e-mail: biuro@pulsar.pl, sales@pulsar.pl
http:// www.pulsar.pl, www.zasilacze.pl
1 / 1

Pulsar SF108 Quick start guide

Category
Network switches
Type
Quick start guide
This manual is also suitable for

Pulsar SF108 is a 10-port PoE switch designed to power IP cameras compliant with the IEEE 802.3af standard. It features 8 PoE ports with a power budget of 15.4W each, 1 uplink port (G1/TP), and 2 uplink ports (G1/SFP, G2/SFP) for fiber optic transmission. The switch supports auto-learning and auto-aging of MAC addresses (1K size) and provides LED indication for power, PoE status, and link activity. It comes with a 48VDC/2.5A/120W max power supply and includes additional assembly elements.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document