PSU-B-13,8V/S-1,5A/1/EL-TR-1,2Ah/DIN
PSBAD 1512
v.2.0
Buffer, switching power supply unit
in the casing for the DIN rail 35mm.
EN
Edition: 2 from the 27th March 2009
Supercedes edition:
1 from the 15th December 2008
01102009
2
CONTENTS:
1. Technical description.
1.1. General description
1.2. Block diagram
1.3. Description of elements and power supply connectors
1.4. Technical parameters
2. Installation.
2.1. Requirements
2.2. Installation procedure
3. Monitoring of the power supply operation.
3.1. Optical signaling
3.2. Technical output
4. Service and operation.
4.1. Overloads or short circuits to the PSU
4.2. Battery assisted operation
4.3 Mainteance
1. Technical description.
1.1. General description.
The buffer power-supply is used for uninterrupted supply of devices requiring stabilized voltage of
12V/DC (+/-15%). The power-supply provides voltage within the following range: U= 11,0V÷13,8 V DC of total current
efficiency equal to Imax=1,5A. In case of power voltage decay, prompt switching to battery supply occurs. The power-supply
has the following protections: short-circuit (SCP), overload (OLP), overheat (OHP). It is adapted for cooperation with the sealed
lead-acid battery (SLA). The power supply controls automatically the charging and maintenance process of the battery, what is
more it is equipped with the BAT output protections: short-circuit and reverse polarity protection. The power-supply is equipped
with excessive discharge protection (UVP, jumper A: ON/OFF). It is equipped with the optical signaling indicating the operation
mode (AC power-supply, charging, DC output). In addition, the PSU offers the technical output (COM, NC, NO) used for
controlling the AC supply status. Two jumpers B, C are dedicated for configuring the time lag of AC absence indication.
The power-supply has got a metal casing (RAL 9003 color) with a space for
1,2Ah/12V
battery and mounting on the DIN
rail (TS35mm).
Information about additional equipment for PSBAD1512 power-supply:
- 1x AWO 417: 7Ah battery casing with mounting on the Din rail (7Ah/DIN).
Information about types:
Model Description
PSBA 1512
PSU-B-13,8V/S-1,5A/1/EL-TR-1,2Ah/MC
12V DC buffer (switching) power-supply unit, with the total current capacity 1,5A and
output voltage 11,0V-13,8V. Equipped with TAMPER. Metal casing IP20 with a space for
1,2Ah battery
PSBB 1512
PSU-B-13,8V/S-1,5A/1/EL-TR-7Ah/MC
12V DC buffer (switching) power-supply unit, with the total current capacity 1,5A and
output voltage 11,0V-13,8V. Equipped with the AC supply absence indication system
(battery assisted operation) and TAMPER. Metal casing IP20 with a space for 7Ah battery.
PSBAH 1012
PSU-B-13,8V/S-1,0A/1/EL-TR-1.2Ah/HC
12V DC buffer (switching) power-supply unit, with the total current capacity 1,0A and
output voltage 11,0V-13,8V. Equipped with TAMPER. ABS IP65 casing with a space
for 1,2Ah battery.
PSBBH 1012
PSU-B-13,8V/S-1,0A/1/EL-TR-7Ah/HC
12V DC buffer (switching) power-supply unit, with the total current capacity 1,0A and
output voltage 11,0V-13,8V. Equipped with TAMPER. ABS IP65 casing with a space
for 1,2Ah or 7Ah battery.
PSBAD1512
PSU-B-13,8V/S-1,5A/1/EL-TR-1,2Ah/DIN
12V DC buffer (switching) power-supply unit, with the total current capacity 1,5A and
output voltage 11,0V-13,8V. Equipped with the AC supply absence indication system
(battery assisted operation) and TAMPER. Metal casing IP20 with a space for 1,2Ah
battery for installation on the DIN rail. 35mm.
3
1.2. Block diagram (fig.1).
Fig.1. Block diagram of the PSU.
1.3. Description of elements and connection links of the PSU (tab.1, tab.2, fig.2).
No.
[fig.2]
Description
[1]
A, jumper - configuration of UVP battery protection function
• A= protection function (disconnection) of the battery off
• A= protection function (disconnection) of the battery on
(disconnection U<10V)
B, C jumpers - configuration of AC absence indication time lag
• B= , C= time lag T= 5s
• B= , C= time lag T= 140s
• B= , C= time lag T= 1040s (17m 20s)
• B= , C= time lag T= 2h 20m 30s
Legend:
jumper installed
jumper removed
[2] START pushbutton (power activation without AC supply)
[3] P1 potentiometer, voltage adjustment
[4] F1 fuse in the battery circuit
[5] AC, LB, AUX optical indication of the power-supply unit operation
[6] AC, AUX Connection link of the output of the additional optical indication
[7] OUTPUTS connector (Tab.2)
[8] BAT+/BAT-: outputs, battery connectors +BAT=red, - BAT=black
[9] F2 witch in the power supply circuit (230V/AC)
[10]
L-N power-supply connector 230V/AC, PE protection connector
[11]
J, jumper - the limitation of the battery charging current
J : Ibat=200 mA max.
J : Ibat=500 mA max.
Legend:
jumper installed
jumper removed
Tab.1. The elements of the power-supply unit.
Table 2.
[3] Description of power-supply unit outputs
~AC~
AC supply input (16V-22V AC)
+BAT
-BAT
DC supply output of the battery
(+BAT= red, -BAT=black)
+AUX DC supply output
4
-AUX (+AUX= +U, -AUX=GND)
COM
NC
NO
Technical output of AC absence – relay assisted
COM= common contact
NC= normally closed contact (without AC supply)
NO= normally opened contact (without AC supply)
Tab.2. Output terminals of the power-supply.
Fig.2. The view of the power-supply.
5
1.4. Technical parameters:
- electrical parameters (tab.3)
- mechanical parameters (tab.4)
- operation safety (tab.5)
- operation parameters (tab.6)
Electrical parameters (tab. 3).
Supply voltage 230V/AC (-15%/+10%)
Supply frequency 50Hz (47÷53Hz)
PSU power P 21W max.
Current consumption 0,16 A max. (2,5 A „ cold boot”)
Output voltage 11,0V÷13,8Vdc – buffer operation
10,0V÷13,8Vdc – battery assisted operation
Output voltage setting, escalation and keeping
time
60ms/40ms/10ms @ Inom., Uac=min.
Voltage setting range
11,5 V÷14,0 V
Voltage adjustment range
± 1%
Ripple voltage
30mV p-p max.
Output current
1,5 A max.
Current consumption by PSU systems
25 mA max.
Battery charging current
200mA max. (@7Ah, U bat.=10,0V) (± 5%)
SCP short-circuit protection
200% ÷ 250% of supply power – limitation of current and/or fuse
failure in the battery circuit (fuse-element replacement required)
OLP overload protection
110% ÷ 150% (@25ºC÷55ºC) of power supply – current limitation
with the PTC automatic fuse, manual restart (the fault requires
the disconnection of the DC output circuit)
SCP short-circuit protection in the battery circuit
and reverse polarity protection
2A- current limitation, F2 fuse (failure requires replacement of the
fuse-element)
Overvoltage protection OVP U>22V varistor, automatically recovered
Excessive discharge protection UVP U<10,0 V (± 5%) – disconnection of (-BAT) battery
Technical outputs:
- COM, NC, NO output indicating the fault to the
AC supply
-
R-relay type, 1A@ 30Vdc/50Vac max.
Time lag about 5s/140s/1040s/2h20m30s (+/-1%)
Normal status: activated COM-NO,
Failure status: activated COM-NC
Optical indication: power-supply
- AC diode indicating the AC supply status
- LB diode indicating the battery charging
process
- AUX diode indicating DC supply status at the
power-supply output
Optical indication: power-supply front panel
- AC diode indicating the AC supply status
- AUX diode indicating DC supply status at the
power-supply output
- red, normal status, permanently illuminated,
failure: no illumination
- red, illuminated with light with intensity depending on battery
charging current
- green, normal status, permanently illuminated,
failure: no illumination
- red, normal status, permanently illuminated,
failure: no illumination
- green, normal status, permanently illuminated,
failure: no illumination
F1 fuse
F2 fuse
F 2A/250V
T 250 mA/ 250V
Mechanical parameters (tab.5)
Casing dimensions 185 x 100 x 102 (WxHxD) [mm] (+/- 2)
Fixation On DIN rail TH35
Battery space 1,2h/12V (SLA) max. (casing of 7Ah/DIN – AWO417 battery)
Net/gross weight 1,7/1,8 kg
Casing color RAL 9003
Closing Cheese screw x 2 (at the front)
Connectors Power-supply: Φ0,63-2,50 (AWG 22-10)
Outputs: Ф0,41÷1,63 (AWG 26-14)
BAT battery outputs: 6,3F-2,5, 30cm
TAMPER output: wires, 30cm
Notes The casing is distant from the assembly surface so that cables can be installed
6
Operation safety (tab.5)
Protection class PN-EN 60950-1:2004 I (first)
Protection class PN-EN 60529: 2002 (U) IP20
Electrical strength of insulation:
- between input (network) circuit and output circuits of power-supply
(I/P-O/P)
- between input circuit and PE protection circuit (I/P-FG)
- between output circuit and PE protection circuit (O/P-FG))
3000 V/AC min.
1500 V/AC min.
500 V/AC min.
Insulation resistance:
- between input circuit and output or protection circuit
100 MΩ, 500V/DC
Operation parameters (tab. 6)
Operation temperature
-10ºC...+40ºC
Storage temperature
+5ºC...+40ºC
Relative humidity 30%...90%, without condensation
Vibrations during operation Unacceptable
Impulse waves during operation Unacceptable
Direct isolation Unacceptable
Vibrations and impulse waves during transport According to PN-83/T-42106
2. Installation.
2.1 Requirements.
The buffer power-supply shall be mounted by the qualified installer having appropriate (required and
necessary for a given country) permissions and qualifications for connecting (operating) 230V/AC installations and
low-voltage installations. The device shall be mounted in closed rooms, according to the environment class II, of
the normal air humidity (RH=90% max. without condensation) and the temperature within the range from -10°C
to +40°C. The power-supply shall operate in a vertical position so that free and convectional air flow through
ventilating holes of the casing is guaranteed.
Before installation is started, the balance of the power-supply load shall be performed. During the normal
operation, the sum of currents collected by receivers shall not exceed I=1,5A (P=21W max.) considering that
the maximum battery charging current Ibat=500mA.
As the power-supply is designed for a continuous operation and is not equipped with a power-switch,
therefore an appropriate overload protection in the power supply circuit shall be guaranteed. Moreover, the user
shall be informed about the method of isolation of the power supply from the power voltage (usually through
assignment and marking of an appropriate fuse in the fuse-box). The electrical system shall be made in accordance
with valid standards and regulations.
2.2 Installation procedure.
1. Before installation is started, the voltage in the 230V power-supply circuit shall be isolated.
2. Install the PSU on DIN rail: mount the enclosure on DIN rail, lock by the fastener, insert cables through gum
bushings.
3. The power cables (~230Vac) shall be connected to L-N terminals of the power supply. The earth conductor
shall be connected to the terminal marked by the earth symbol . The connection shall be made by means of a
three-core cable (with a yellow and green PE protection wire). The power cables shall be lead to appropriate
terminals of the connection board through bushing.
The circuit of the shock protection shall be performed with a particular care, i.e. the yellow
and green protection wire of the power cable shall be connected from one side to the
terminal marked by the symbol of in the casing of the power-supply. Operation of the
power-supply without the properly made and fully operational circuit of the shock
protection is
UNACCEPTABLE!
It can result in failure of devices and electric shock.
7
RED DIODE:
• lights – the power-supply unit supplied with 230V AC
• does not light – no 230V AC supply
GREEN DIODE
• lights – DC voltage at the AUX output of the power-supply
unit
•
does not light – no DC voltage at the AUX power supply
output
4. Connect the conductors of consumers to the +AU, -AUX terminals of the terminal box on the power-supply unit.
5. If necessary, connect the conductors from the equipment to the technical outputs:
- COM-NC-NO AC supply status signaling (alarm panel, controller, signaling unit, LED diode, etc.). Use the ‘B, C’
jumpers to determine the indication time lag.
6. Activate the ~230V/AC supply (the AC red diode should be permanently illuminated, and AUX diode should be
permanently illuminated)
7. Check the output voltage (the PSU voltage without load should be anywhere between 13,6V-13,9V, and during
battery charging 11V-13,8V). If the value of the voltage requires adjustment, the setting should be made by means
of the potentiometer P1, monitoring the voltage at the AUX output of the PSU.
8. Connect the battery in accordance with the indications: +BAT red to ‘plus’ , -BAT black to ‘minus’, (the LB diode
should go on and the lighting intensity should reduce with the charging time elapsed increasing).
9. Once the tests and control operation have been completed, lock the enclosure, cabinet, etc.
3. The power supply operation indication.
3.1 Optical indication.
The is equipped with two diodes on the front panel:
Moreover, the PSU is equipped with three diodes indicating operation status: AC, LB, AUX placed on the
PCB of the power supply unit:
• AC- red diode: under normal status (AC supply) the diode is permanently illuminated. The absence of AC
supply is indicated by the AC diode going off.
• LB- red diode: indicates the battery charging process; the intensity of illumination is dependent on the
charging current: 0,5A=100%.......0A=0%.
AUX- green diode: indicates the DC supply status at the output of the PSU. Under normal status, the
diode is permanently illuminated and in the case of short-circuit or overload, the diode goes off.
3.2 Technical outputs.
The PSU is equipped with indication outputs allowing transmitting the information of the absence of AC supply.
• COM-NC-NO: AC supply absence output: -relay output indicates the absence of AC supply.
Under normal status, with the AC supply on, the COM-NO contacts are closed and in the case of AC supply
loss, the PSU will switch over the COM-NC contacts closed after the expiry of time set by the jumpers ‘B’
and ‘C’.
4. Handling and operation.
4.1 Overload or short-circuits to the PSU output.
The AUX output of the PSU is equipped with the PTC polymer fuse assisted protection. If the load of the
PSU exceeds Imax. (load 110% ÷ 150% @25ºC of the PSU power), the output voltage is automatically
disconnected and this is indicated by the green diode going off. The voltage at the output may be restored by
disconnecting the output load for the period of about one minute.
In the case of the short-circuit to the AUX, BAT output, (load 200% ÷ 250% of the PSU power) or
incorrect connection of the battery, the fuse F1 in the battery circuit becomes permanently damaged and the
restoration of the voltage at the BAT output requires the replacement of the fuse.
4.2 Battery assisted operation.
In the case of power failure, in the unit will instantly switch to the battery assisted operation.
In order to activate the operation of the PSU from the battery itself, connect the BAT connectors in accordance
with the indications: +BAT red to ‘plus’ and, -BAT black to 'minus’ of the battery and press and keep depressed for
five seconds the START pushbutton on the equipment board. Turning off the Power Supply: Disconnect connectors
BAT+ or BAT- from the battery.
8
The PSU is equipped with the discharged battery disconnection system; the configuration of
functions through the jumper ‘A’. The battery protection is on if the jumper ‘A’ is removed.
4.3 Maintenance.
Any and all maintenance operations may be performed following the disconnection of the PSU from the power
supply network. The PSU does not require performing any specific maintenance measures, however, in the case of
significant dust rate, its interior is recommended to be cleaned with compressed air. In the case of fuse
replacement, only the substitutes in conformity to the original ones are allowed.
WEEE MARK
The used electric and electronic products, do not mix with general household waste.
There are separate collection system for used electric and electronic products in
accordance with legislation under the WEEE Directive and is effective only with EU.
Pulsar K.Bogusz Sp.j.
Siedlec 150,
32-744 Łapczyca, Polska
Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50
e-mail: biuro@pulsar.pl, [email protected]
http:// www.pulsar.pl
WARRANTY
24 months since the sale date, 36 months since the production date.
THE WARRANTY IS VALID ONLY after presenting the invoice of the sale to which the claim refers.
/
