Sanyo LCD-37CA8Z Owner's manual

Sanyo
Brand
Sanyo
Model
LCD-37CA8Z
Category
LCD TVs
Type
Owner's manual

This manual is also suitable for

Owner’s Manual
LCD TV
MODEL
LCD-32CA8Z
LCD-37CA8Z
LCD-42CA8Z
Inst. Manual - CA8Z.indd 1 6/27/2007 5:45:00 PM
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
ƽ
Install the LCD TV in a proper position. If not, it may result in a fire hazard.
ƽ
Provide appropriate space on the top, sides and rear of the LCD TV
cabinet for allowing air circulation and cooling the LCD TV. Minimum
clearance must be maintained. If the LCD TV is to be built into a
compartment or similarly enclosed, the minimum distances must be
maintained. Do not cover the ventilation slot on the LCD TV. Heat
build-up can reduce the service life of your LCD TV, and can also be
dangerous.
ƽ
If the LCD TV is not to be used for an extended time, unplug the LCD TV
from the power outlet.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
2
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
OWNER'S MANUAL WITH THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Before operating this LCD TV, read this manual thoroughly and operate the LCD TV properly.
This LCD TV provides many convenient features and functions. Operating the LCD TV properly enables you to manage those
features and maintains it in better condition for a considerable time.
Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.
If your LCD TV seems to operate improperly, read this manual again, check operations and cable connections and try the solutions
in the "Troubleshooting" section on page 37 of this booklet. If the problem still persists, contact the dealer where you purchased the
LCD TV or the service center.
TO THE OWNER
Safety Precaution
Caution In Installing
ƽ Handle the
LCD TV
carefully when installing it and do not drop.
ƽ Locate set away from heat, excessive dust, and direct sunlight.
ƽ For correct installation and mounting it is strongly recommended to use a trained, authorized dealer. Failure to follow
correct mounting procedures could result in damage to the equipment or injury to the installer.
SIDE and TOP
REAR
10 cm
10 cm
10 cm
6 cm
Inst. Manual - CA8Z.indd 2 6/27/2007 5:45:01 PM
3
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before
the product is operated.
Read all of the instructions given here and retain them for
later use. Unplug this LCD TV from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Follow all warnings and instructions marked on the LCD TV.
For added protection to the LCD TV during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not expose this unit to rain or use near water... for example,
in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
Do not place this LCD TV on an unstable cart, stand, or table.
The LCD TV may fall, causing serious injury to a child or adult,
and serious damage to the LCD TV. Use only with a cart or
stand recommended by the manufacturer, or sold with the LCD
TV. Wall or shelf mounting should follow the manufacturer's
instructions, and should use a mounting kit approved by the
manufacturers.
An appliance and cart combination
should be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
Slots and openings in the back and bottom of the cabinet
are provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the LCD TV on a rug, or other similar surface. This
LCD TV should never be placed near or over a radiator or heat
register.
This LCD TV should not be placed in a built-in installation such
as a book case unless proper ventilation is provided.
Never push objects of any kind into this LCD TV through
cabinet slots as they may touch dangerous voltage points
or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the LCD TV.
Do not place items such as vases containing liquid on top of
the LCD TV.
Do not install the LCD TV near the ventilation duct of air-
conditioning equipment.
This LCD TV should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this LCD TV where the cord may
be damaged by persons walking on it.
Do not attempt to service this LCD TV yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
Unplug this LCD TV from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the LCD TV.
c. If the LCD TV has been exposed to rain or water.
d. If the LCD TV does not operate normally by following the
operating instructions. Adjust only those control that are
covered by the operating instructions as improper adjust-
ment of other control may result in damage and will often
require extensive work by a qualified technician to restore
the LCD TV to normal operation.
e. If the LCD TV has been dropped or the cabinet has been
damaged.
f. When the LCD TV exhibits a distinct change in perfor-
mance-this indicates a need for service.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or injury to persons.
Upon completion of any service or repairs to this LCD TV,
ask the service technician to perform routine safety checks to
determine that the LCD TV is in safe operating condition.
Inst. Manual - CA8Z.indd 3 6/27/2007 5:45:01 PM
4
TABLE OF CONTENTS
BEFORE OPERATION 10
APPENDIX 36
PREPARATION 5
PART NAMES AND FUNCTIONS
5
CONNECTING LCD TV
7
PREVENTING THE TV FROM FALLING OVER
7
CONNECTING THE AC POWER CORD
7
CONNECTING OUTDOOR AERIAL
8
CONNECTING A COMPUTER
8
CONNECTING VIDEO EQUIPMENT
9
OPERATION OF REMOTE CONTROL
10
OPERATION RANGE 11
REMOTE CONTROL BATTERIES INSTALLATION 11
ON-SCREEN MENU 12
CLEANING LCD TV 36
FUNCTION OF PRODUCT SAFETY FEATURE 36
TROUBLE SHOOTING 37
TECHNICAL SPECIFICATIONS 38
BASIC OPERATION 15
TURNING ON/OFF LCD TV 15
SELECTING INPUT SOURCE 15
CHANNEL SELECTION 16
CHANNEL RECALL 17
RECALL/COLOUR SYSTEM 17
MUTE 17
AUDIO MODE 17
VOLUME CONTROL 18
BASS EXPANDER 18
SURROUND 18
STILL 18
ZOOM 19
PICTURE 20
SOUND 20
MENU OPERATION 28
PICTURE 28
SOUND 29
TUNER 30
TIME 32
SETUP 33
PC Adj. 34
DEALER MODE 35
PREVENTING THE TV FROM FALLING 7
OVER
PREVENTING THE TV FROM FALLING OVER
7
TIMER
CURRENT TIMER 21
OFF TIMER 21
ON TIMER 22
ON POSITION 22
PIP/POP OPERATION 23
OPERATION OF REMOTE CONTROL (IN TEXT MODE)
24
TEXT/TV 25
TEXT REVEAL 25
TEXT CANCEL 25
TEXT INDEX 25
TEXT SUBCODE 26
TEXT SIZE 26
TEXT HOLD 26
TEXT RED 27
TEXT GREEN 27
TEXT BLUE 27
TRADEMARKS
ƽ Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
ƽ IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
ƽ is trademark or registered trademark of HDMI
Licensing,LLC.
This symbol on the nameplate means the product has obtained the usufruct of HDMI by HDMI
Licensing,LLC.
ƽ Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective
corporation.
Inst. Manual - CA8Z.indd 4 6/27/2007 5:45:01 PM
5
PREPARATION
PART NAMES AND FUNCTIONS
FRONT
INDICATORS
INFRARED REMOTE RECEIVER
POWER INDICATOR
ON TIMER INDICATOR
INDICATORS
SIDE CONTROLS
STAND
Ɣ 'RQRWEXPSRUVFUDWFKWKHSDQHOVXUIDFHDVWKLVFDXVHVIODZVRQWKHVXUIDFHRIWKHVFUHHQ
Ɣ 7KHUHPD\EHVRPHWLQ\EODFNSRLQWVDQGRUEOLJKWSRLQWVRQWKH6&5((17KHVHSRLQWVDUHQRUPDO
CARE FOR USING LCD TV
Inst. Manual - CA8Z.indd 5 6/27/2007 5:45:02 PM
6
PREPARATION
PART NAMES AND FUNCTIONS
SIDE CONTROLS
SIDE TERMINALS
(Each button on the control panel has the same function with its counterpart on the remote
controls. )
CHANNEL UP/DOWN
Ÿź buttons
Used to Change channels.
Used to select items.
VOLUME
(+/-)
buttons
Adjust the volume level.
Adjust the value of the selected item
in the On- Screen Menu.
Execute the selected menu in the
On-Screen Menu.
Select an input source: TV/AV1/
AV2(DVD)/PC/HDMI.
Open or close the On-Screen Menu.
MENU button
INPUT button
Connect a television, video recorder
or external audio amplifier to these
jacks.
Ɣ9LGHR5&$W\SH
Ɣ$XGLR/DQG55&$W\SH
Connect all kinds of HDMI output equipment
to this terminal.
HDMI INPUT TERMINAL
Connect video and audio output from
video equipment.
Ɣ$XGLR/DQG55&$W\SH
Ɣ'9'FRPSRQHQW5&$W\SH
Note:
AV2 can be connected to composite video or
DVD component terminals.
1. Composite Video input: Connect to Y(V), L, R
terminals.
2. DVD Component input: Connect to Y(V), CB/PB,
CR/PR, L, R terminals.
VIDEO INPUT TERMINALS
POWER ON/ STAND-BY button
Turn the LCD TV on or off.
Connect computer output to these
terminals.
Ɣ
RGB (D-SUB)
ƔAudio (L / R)
Connect the cable with a plug from
aerial jack to the aerial socket on the
cabinet back.
HEADPHONE JACK
Connect a headphone (stereo) to this jack.
When this jack is used, speaker sound will be
lost.
VIDEO INPUT TERMINALS
Connect video and audio output from video
equipment.
Ɣ9LGHR5&$W\SH
Ɣ$XGLR/DQG55&$W\SH
Ɣ69LGHR0LQL',1W\SH
PC INPUT TERMINALS
MONITOR OUTPUT TERMINALS
AERIAL JACK
Inst. Manual - CA8Z.indd 6 6/27/2007 5:45:04 PM
7
PREVENTING THE TV FROM FALLING OVER
CONNECTING THE AC POWER CORD
This LCD TV uses nominal input voltages of 100-242V AC. It
is designed to work with single-phase power systems having a
grounded neutral conductor. To reduce risk of electrical shock,
do not plug into any other type of power system.
Consult your authorized dealer or service station if you are not
sure of the type of power being supplied.
Connect the LCD TV with all peripheral equipment before
turning the LCD TV on.
CAUTION
For safety, unplug AC power cord when the
LCD TV is not in use.
When this LCD TV is connected to an outlet with AC
power cord, it is in Stand-by mode and consumes a
little electric power.
AC Power Cord
To the AC Outlet (100 - 242V AC)
Pulls the AC power cord out from the
LCD TV. The AC outlet must be near this
equipment and must be easily accessible.
Carry out the steps given below to stabilize the TV that it will be safe in the event of a disaster such as an earthquake, and
so that it will not fall over during normal use.
Use the marketed bands and screws to fasten the TV securely to the TV stand etc.
CONNECTING LCD TV
PREVENTING THE TV FROM FALLING OVER
TV Stand etc.
Mounting screw
(Not supplied)
Band
(Not supplied)
Inst. Manual - CA8Z.indd 7 6/27/2007 5:45:06 PM
8
CONNECTING LCD TV
CONNECTING A COMPUTER
IBM-compatible
computers or
Macintosh computers
(VGA / SVGA / XGA )
Desktop
type
Laptop
type
Cables used for connection (These cables are not supplied with this LCD TV.)
Ɣ3&&DEOH'68%SLQ
Ɣ0$&$GDSWHULQWKHFDVHRIFRQQHFWLQJ0DFLQWRVKFRPSXWHU
Ɣ$XGLR&DEOH>0LQL3OXJ/5@
Ɣ+'0,&DEOH+'0,,QSXW
NOTE:
When connecting the cable, AC Power Cords of
both LCD TV and external equipment should be
disconnected from AC outlet. Turn LCD TV and
peripheral equipment on before your computer is
switched on.
SIDE TERMINALS
CONNECTING OUTDOOR AERIAL
Aerial Cable
Outdoor
Aerial
CONNECTING OUTDOOR AERIAL
Cable used for connectting outdoor
aerial with aerial jack.
( This cable not supplied with this LCD TV.)
CONNECTING INDOOR AERIAL
Cable used for connectting wired socket
with aerial jack.
( This cable not supplied with this LCD TV.)
NOTE:
For all aerial circuit problems please consult your
local dealer.
Monitor Output
PC Cable
PC IN
Audio Cable
(Mini Plug)
Audio Output
(stereo)
MAC ADAPTER
PC AUDIO (L / R) IN
HDMI Cable
HDMI IN
HDMI Output
Digital AV Equipment
AERIAL JACK
Inst. Manual - CA8Z.indd 8 6/27/2007 5:45:07 PM
9
CONNECTING VIDEO EQUIPMENT
Cables used for connection (These cables are not supplied with this LCD TV.)
Ɣ9LGHR&DEOH5&$;69LGHR&DEOH$XGLR&DEOH5&$;9LGHRRU9LGHR
Ɣ9LGHR&DEOH5&$;$XGLR&DEOH5&$;'9'&RPSRQHQW9LGHR
Ɣ9LGHR&DEOH5&$;$XGLR&DEOH5&$;0RQLWRU2XWSXW
NOTE :
When connecting the cable, AC Power Cords of both LCD TV and
external equipment should be disconnected from AC outlet.
CONNECTING LCD TV
External monitor
Composite Video
and Audio Output
External Audio
Equipment
Audio
Speaker
(stereo)
Audio Amplifier
Note :
Video (RCA) output is for
TV, AV or S-VIDEO only.
Video cable
(RCA x1)
Audio cable
(RCA x 2)
MONITOR OUT
CR/PR, CB/PB, Y
Video Source (example)
Video Cassette
Recorder
Video Disc
Player
DVD Player
DVD (RCA x 3)
Audio cable
(RCA x 2)
Component Video Source
(example)
DVD video equipment.
(such as DVD player or
high-definition TV source)
S-Video
output
S-Video
S-Video
Cable
Video and Audio
cable (RCA x 3)
Note:
ƔWhen AV2 input jack is connected to composite video, the connecting way is the same as AV1 input jack.
ƔYou can select the signal from S-Video input or from Video input in menu operation.
R L
R , L , V
Inst. Manual - CA8Z.indd 9 6/27/2007 5:45:07 PM
10
BEFORE OPERATION
ON/STAND-BY button
SOUND SYSTEM button
PIP ON/OFF button
MUTE button
NUMERIC buttons
SURROUND button
RECALL/COLOUR
SYSTEM button
SOUND button
BASS button
CHANNEL RECALL button
VOLUME + (Ź) button
DIGIT button
MENU button
OPERATION OF REMOTE CONTROL
TV/AV MODE button
OK button
BACK button
MAIN/SUB button
PC MODE button
WIDE button
This button is not used.
TIMER button
CHANNEL UP /
DOWN buttons
POP button
VOLUME ( +/- ) buttons
STILL button
VOLUME - (Ż) button
&+$11(/83ŸEXWWRQ
&+$11(/'2:1źEXWWRQ
STEREO/MONO button
PICTURE button
Note: In different mode, some keys have different functions. For example, STILL button in this mode
has STILL function, but in Teletext mode, it has only Teletext RED function, so called
"TEXT RED button". (For details, please refer to page 24.)
These buttons are used for Sanyo
VCR and DVD player. Thay are
have the same functions with its
counterpart on Sanyo VCR's or DVD
player's remote controls. Refer to the
operation by the manual instruction
of Sanyo VCR or DVD player to use
these buttons.
CHANGE button
Inst. Manual - CA8Z.indd 10 6/27/2007 5:45:08 PM
11
BEFORE OPERATION
REMOTE CONTROL BATTERIES INSTALLATION
OPERATING RANGE
Point Remote Control toward LCD TV (Infrared Remote
Receiver) whenever pressing the buttons. Maximum
operating range for Remote Control is about 16.4' (5m) in
front, about 30º to the left or the right, about 15º for up or
down.
INSTALLING BATTERIES
1. Remove the battery compartment cover as shown in figure.
2. Insert two size AAA batteries (1.5V) according to "+" and "-" polarity
markings inside the battery compartment.
3. Close the battery compartment cover.
To insure safe operation, please observe the following precautions:
Ɣ 8VH$$$DONDOLQHEDWWHULHV
Ɣ 5HSODFHWZREDWWHULHVDWWKHVDPHWLPH
Ɣ 'RQRWXVHDQHZEDWWHU\ZLWKDXVHGEDWWHU\
Ɣ $YRLGFRQWDFWZLWKZDWHURUOLTXLG
Ɣ 'RQRWH[SRVHWKH5HPRWH&RQWUROWRPRLVWXUHRUKHDW
Ɣ 'RQRWGURSWKH5HPRWH&RQWURO
Ɣ ,IDEDWWHU\KDVOHDNHGRQWKH5HPRWH&RQWUROFDUHIXOO\ZLSHFDVHFOHDQ
and install new batteries.
Ɣ 5LVNRIH[SORVLRQLIEDWWHU\LVUHSODFHGE\DQLQFRUUHFWW\SH
Ɣ 'LVSRVHRIXVHGEDWWHULHVDFFRUGLQJWRWKHLQVWUXFWLRQV
NOTE: The shape of Remote Control shall be referred to the object.
Infrared Remote Receiver
16.4'(5 m)
30
30
Inst. Manual - CA8Z.indd 11 6/27/2007 5:45:10 PM
12
BEFORE OPERATION
Picture MENU
ON-SCREEN MENU
Sound MENU
Tuner MENU
Note:
Ɣ
"Tint" can only works in NTSC system.
Ɣ
"Tuner" can only works in TV mode.
MENU LIST
Brightness
Contrast
Colour
Sharpness
White Tone
Tint
50
Select
Adjust
Return
Exit
MENU
Advanced Settings
Picture
Sound
Tuner
Time
Setup
PC Adj.
50
50
50
50
Ż6WDQGDUGŹ
•••
Ÿ
ź
ŻŹ
BACK
Contrast
Colour
Sharpness
White Tone
Tint
Select
Adjust
Return
Exit
MENU
Advanced Settings
Picture
Sound
Tuner
Time
Setup
PC Adj.
50
50
50
50
Ż6WDQGDUGŹ
•••
Ÿ
ź
ŻŹ
BACK
Brightness
50
ACC/ACM
CCS
MPEG NR
Film Mode
DNR
Select
Adjust
Return
Exit
MENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
Ż2QŹ
Ÿ
ź
ŻŹ
BACK
Ż9LYLGŹ
Ż$XWRŹ
Ż$XWRŹ
Ż2QŹ
DCDi
Ż2QŹ
Treble
Bass
Balance
15
Select
Adjust
Return
Exit
MENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
15
0
Ÿ
ź
ŻŹ
BACK
Surround
Bass Expander
Ż2IIŹ
Ż2IIŹ
Auto Search
Semi-Auto Search
Manual Search
Colour System
Select
Adjust
Return
Exit
MENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
Ÿ
ź
ŻŹ
BACK
Sound System
Skip
Channel Swap
Ż3$/Ź
Ż'.Ź
Ż2QŹ
•••
>>>
>>>
>>>
Auto Secrching
Please Wait...
1
ŻŹ
Search Return Exit
MENUBACK
Semi-Auto Searching
Please Wait...
1
ŻŹ
Search Return Exit
MENUBACK
Manual Search
1
ŻŹ
Search Return Exit
MENUBACK
Inst. Manual - CA8Z.indd 12 6/27/2007 5:45:11 PM
13
BEFORE OPERATION
MENU LIST (Continue)
Time MENU
MAIN MENU
Tuner MENU
Auto Search
Semi-Auto Search
Manual Search
Colour System
Select
Adjust
Return
Exit
MENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
Ÿ
ź
ŻŹ
BACK
Sound System
Skip
Channel Swap
Ż3$/Ź
Ż'.Ź
Ż2QŹ
•••
>>>
>>>
>>>
Brightness
Contrast
Colour
Sharpness
White Tone
Tint
50
Select
Adjust
Return
Exit
MENU
Advanced Settings
Picture
Sound
Tuner
Time
Setup
PC Adj.
50
50
50
50
Ż6WDQGDUGŹ
•••
Ÿ
ź
ŻŹ
BACK
Target Channel
Swapping
Select
Adjust
Return
Exit
MENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
Ÿ
ź
ŻŹ
BACK
0
>>>
Current Time
Off Time
On Time
On Position
Select
Adjust
Return
Exit
MENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
Ÿ
ź
ŻŹ
BACK
ŻŹ
--:--
--:--
--:--
Current Channel
3
Inst. Manual - CA8Z.indd 13 6/27/2007 5:45:12 PM
14
BEFORE OPERATION
MENU LIST
PC Adj. MENU
Note:
Ɣ
"PC Adj." doesn't work if no signal is input in PC mode.
Ɣ
"PC Adj." can only works in PC mode.
Setup MENU
Menu Setup
Select
Adjust
Return
Exit
MENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
Ÿ
ź
ŻŹ
BACK
•••
PIP/POP Setup
Initial Settings
•••
>>>
Initial Settings
Return
BACK
Confirm
OK
Brightness
Contrast
Colour
Sharpness
White Tone
Tint
50
Select
Adjust
Return
Exit
MENU
Advanced Settings
Picture
Sound
Tuner
Time
Setup
PC Adj.
50
50
50
50
Ż6WDQGDUGŹ
•••
Ÿ
ź
ŻŹ
BACK
Select
Adjust
Return
Exit
MENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
Ÿ
ź
ŻŹ
BACK
Main Source
Sub Source
PIP Position
Ż7RS/HIWŹ
Ż79Ź
Ż+'0,Ź
Auto Adjust
Select
Adjust
Return
Exit
MENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
Ÿ
ź
ŻŹ
BACK
>>>
H-Position
V-Position
Clock
Phase
50
50
50
50
Mode
Ż3,3Ź
Select
Adjust
Return
Exit
MENU
Picture
Sound
Tuner
Time
Setup
PC Adj.
Ÿ
ź
ŻŹ
BACK
H-Position
V-Position
Duration
Transparence
50
50
ŻVŹ
50
Language
Ż(QJOLVKŹ
Teletext Lang.
Ż$UDELFŹ
Inst. Manual - CA8Z.indd 14 6/27/2007 5:45:13 PM
15
BASIC OPERATION
SELECTING INPUT SOURCE
Select mode "TV", "AV1 (VIDEO / S-VIDEO)", "AV2/DVD", "HDMI", or "PC" by pressing TV/AV MODE button and PC
MODE button on Remote Controls or pressing INPUT button on SIDE Controls.
2
AV2/DVD
AV1/S-VIDEO
PC
REMOTE CONTROLS
HDMI
Connect the LCD TV's AC power cord into an AC outlet.
2
TURNING ON / OFF LCD TV
1
Complete the peripheral connections before turning on LCD TV.
(Please refer to "CONNECTING LCD TV".)
ON/ STAND-BY button
NO SIGNAL SHUT OFF
This TV set incorporates the NO SIGNAL SHUT OFF function.
If no signal is input in TV mode, "OFF 0:10" will display for
about 10 minutes as the right picture, and TV will be turned off
automatically.
3
ON/ STAND-BY
button
Press ON/STAND-BY button on Side Controls of LCD TV or on
Remote Controls to turn it ON. The POWER indicator will light up
(green). Press ON/STAND-BY button again to shift it to stand-by
status, the POWER indicator will become red.
SIDE CONTROLS
REMOTE CONTROLS
12
AUTO
AUTO
Mono
OFF 0:10
Note: It is possible to return to TV mode directly by pressing NUMERIC buttons from other input modes.
(TV mode)
INPUT button
TV/AV MODE button
PC MODE button
SIDE CONTROLS
Inst. Manual - CA8Z.indd 15 6/27/2007 5:45:14 PM
16
BASIC OPERATION
CHANNEL SELECTION
DIRECT SELECTION
To select channel 8:
08
Press "8" button.
CHANNEL UP/DOWN
PressCHANNELUP/DOWN(▲▼)buttonsonSideControlsoronRemoteControlstoselectprograms.
REMOTE CONTROLS
CHANNEL UP/DOWN
(▲▼) buttons
SIDE CONTROLS
CHANNEL UP/DOWN
(▲▼) buttons
There are 256 channels can be selected on the LCD TV.
■
For direct access to programmes using the (0-9) numeric button.
2) For selection of channel position 10 - 99. For channel position 25, press the Digit button to display "- -", then press “2” and
“5” buttons.
1) For selection of channel position 0 - 9. Example: For channel position 8, press the “8” button.
To select channel 25:
Press "2" button. Press "5" button.
Press Digit button.
- -
25
3) For selection of channel position 100 - 199. For channel position 125, press the Digit button twice to display "1 - -", then
press “2” and “5” buttons.
To select channel 125:
Press "2" button. Press "5" button.Press Digit button twice.
12-
125
1- -
2 -
CHANNEL UP/DOWN
(▲▼) buttons
4) For selection of channel position 200 - 255. For channel position 225, press the Digit button three times to display "2 - -",
then press “2” and “5” buttons.
Press "2" button. Press "5" button.Press Digit button three times.
22-
225
2- -
To select channel 225:
Inst. Manual - CA8Z.indd 16 6/28/2007 9:49:57 AM
17
BASIC OPERATION
MUTE
Should you wish to mute the sound, press MUTE button. To switch the
sound back on, press MUTE button again or press VOLUME(+/-) but-
tons on Side Controls or on Remote Controls.
CHANNEL RECALL
Press CHANNEL RECALL button to switch between the previous
channel and the current channel.
For example, now you are watching channel "4", but you watched
channel "2" previously. If you press CHANNEL RECALL button, chan-
nel "2" will appear immediately.
REMOTE CONTROLS
RECALL/COLOUR SYSTEM
Press RECALL/COLOUR SYSTEM button on Remote Controls to
display the status of LCD TV or switch colour system. Press the
RECALL/COLOUR SYSTEM button repeatedly select a colour system
until the optimum image can be produced.
On Position
11
PAL
BG
Mono
Current Time 00: 00
Off Time 00: 00
On Time 00: 00 18
AUDIO MODE
Simply press STEREO/MONO button to select the following audio signals:
"STEREO", "MONO" , "NICAM" , "A" and "B" .
Color System
CHANNEL
RECALL
button
RECALL/COLOUR
SYSTEM button
STEREO/MONO
button
Sound System
REMOTE CONTROLS
REMOTE CONTROLS
REMOTE CONTROLS
Audio Mode
Channel Number
MUTE button
Inst. Manual - CA8Z.indd 17 6/27/2007 5:45:20 PM
18
BASIC OPERATION
BASS EXPANDER
Press BASS button to switch the bass expander function On or Off.
When it is set On, "Bass Expander On" will appear on the screen for a
short while.
SURROUND
Press SURROUND button to switch the SURROUND function On or
Off. When it is set ON, "Surround On" will appear on the screen for a
short while.
VOLUME CONTROL
To adjust the volume value desired by pressing VOLUME(+/-) buttons
on Remote Controls or on Side Controls. The volume dialogue box will
appear on the screen for a short while.
Press VOLUME(+) button to increase volume, and press VOLUME(-)
button to decrease volume.
SIDE CONTROLS
VOLUME(+/-)
buttons
VOLUME(+/-) buttons
BASS button
SURROUND
button
REMOTE CONTROLS
REMOTE CONTROLS
REMOTE CONTROLS
STILL
Press STILL button to switch the still function On or Off.
When in PIP or POP mode, this still function can still main and sub pic-
ture at the same time.
REMOTE CONTROLS
Press STILL button to cancel "Still" function.
STILL PICTURE NATURAL PICTURE
STILL button
Inst. Manual - CA8Z.indd 18 6/27/2007 5:45:21 PM
19
BASIC OPERATION
ZOOM
Full
Zoom
=RRP>&DSWLRQ,1@
Normal
Full
Zoom
Provides real 4 : 3 image on 16 : 9 screen.
Normal
Provides image to fit width of screen by expanding up/down/left/right
of image. This function is suitable to enjoy a normal video signal (4 : 3
aspect ratio) with wide video aspect ratio of 16 : 9 screen.
Natural Wide
6HOHFWVFUHHQVL]HDPRQJ)XOO=RRP=RRP>&DSWLRQ,1@
"Normal" and "Natural Wide" by pressing WIDE button on Remote
Controls.
This function doesn't work if the picture is black out.
This function doesn't work in PIP or POP mode.
Only "Full" mode can be selected when the input mode is "PC"
"HDMI" or "DVD" and the input signal is 1080i, 720p or 1080p.
Natural Wide
ZOOM button
Provides image to fit screen size (16 : 9 aspect ratio) by expanding
image width and height uniformly. This function can be used for
enjoying a letter box mode picture (4 : 3 aspect picture with black bar
on top and bottom edges) with wide video aspect of 16 : 9 screen.
Provides the image that is expanded as "Zoom" mode and moved up
to show more image to include captions. This function can be used for
enjoying a letter box picture with captions.
Provides image to fit width of screen by expanding image width
uniformly. This function can be used for enjoying a squeezed video
signal with wide video aspect ratio of 16 : 9 screen.
When your video equipment (such as DVD) has 16 : 9 output mode,
select 16 : 9 and select "Full" to provide better quality.
=RRP>&DSWLRQ,1@
WIDE
button
REMOTE CONTROLS
Inst. Manual - CA8Z.indd 19 6/27/2007 5:45:22 PM
20
BASIC OPERATION
PICTURE
Select image level by pressing PICTURE button on Remote Controls.
Natural and splendid picture level preset on this LCD TV.
Bright and dynamic picture. It is suitable for nice playback, such as
DVD program.
Inhibit strong contrast and color, it is beneficial for eye protection.
Standard
Dynamic
User presets picture adjustment in Picture mode.
Personal
Soft
Personal
SOUND
Select sound level by pressing SOUND button on Remote Controls.
Normal sound state preset on LCD TV.
Select this mode for talk programs.
Select this mode for music programs.
Standard
News
Select this mode for user to call out the preset sound adjustment in
SOUND menu.
Personal
Music
Music
Personal
REMOTE CONTROLS
REMOTE CONTROLS
Standard
Dynamic
Soft
Standard
News
Eco
Inhibit strong brightness and chroma, it is beneficial for eye protection.
Eco
PICTURE
button
SOUND
button
Inst. Manual - CA8Z.indd 20 6/27/2007 5:45:23 PM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Sanyo LCD-37CA8Z Owner's manual

Sanyo
Brand
Sanyo
Model
LCD-37CA8Z
Category
LCD TVs
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents