Amazon B0753P16BL User manual

Brand: Amazon

Model: B0753P16BL

Type: User manual

This manual is also suitable for

B0753PHV8Z

created by: Impala Services Ltd.Page size: A4

Pyramid Patio Heater

Calefactor Piramidal para Patios

Chauffage pour Patio en Pyramide

B0753P16BL , B0753PHV8Z

English �� 3

Español �� 26

Français �� 49

WARNING

For outdoor use only.

DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open ﬂame.

3. If odor continues, keep away from the appliance and immediately call your gas

supplier or ﬁre department.

DANGER

• Do not store or use gasoline or other ﬂammable vapors and liquids in the vicinity of

this or any other appliance. Do not store an LP-cylinder not connected for use in the

vicinity of this or any other appliance.

WARNING

• Improper installation, adjustment, alteration, service or maintenance can cause

property damage, injury or death. Read the installation, operation and maintenance

instructions thoroughly before installing or servicing this equipment.

DANGER

CARBON MONOXIDE HAZARD

• This appliance can produce carbon monoxide which has no odor.

• Using it in an enclosed space can kill you.

• Never use this appliance in an enclosed space such as a camper, tent,

car or home.

DANGER

• Failure to comply with the precautions and instructions provided with this heater can

result in death, serious bodily injury and property loss or damage from hazards of

fire, explosion, burn, asphyxiation, and/or carbon monoxide poisoning. Only persons

who can understand and follow the instructions should use or service this heater.

Welcome Guide • English

Contents:

Before getting started, ensure the package contains the following components:

x64

6 7

Guard screen x4

Wheel x2

Emitter

Door panel

Control box

Reﬂector

Lower support x4

Back panel

Upper support x4

Side panel x2

Middle plate

Handle

Gas cylinder bracket x3

Silicone ring

Base plate

Flame tube

IMPORTANT SAFEGUARDS

Read these instructions carefully and retain them for future use. If this product is passed to a third party, then

these instructions must be included.

When using the product, basic safety precautions should always be followed to reduce the risk of injury including the

following:

• Alert children and adults to the hazards of high surface temperatures.

Stay away from these surfaces to avoid burning skin or igniting clothing.

• Carefully supervise young children when in the vicinity of the heater.

• Do not hang clothing or any other ﬂammable materials from the heater, or

place on or near the heater.

• Replace any guard or protective device removed for servicing the

appliance prior to placing back in service.

• Installation and repair should be done by a qualiﬁed service person.

The heater should be inspected before use and annually by a qualiﬁed

service person. More frequent cleaning may be required as necessary. It

is imperative that the control compartment, burners, and circulating air

passageway of the appliance be kept clean.

• This manual contains important information about the assembly, operation and maintenance of this product.

General safety information is presented in these ﬁrst few pages and is also located throughout the manual.

Keep this manual for future reference and to educate new users of this product. This manual should be read in

conjunction with the labeling on the product. Safety precautions are essential when any mechanical or LPG fueled

product is involved. These precautions are necessary when using, storing, and servicing. Using this product with

the respect and caution demanded will reduce the possibilities of personal injury or property damage. The following

symbols shown below are used extensively throughout this manual. Always heed these precautions, as they are

essential when using any mechanical or fueled product.

General Safety

• Never leave the product unattended when hot or in use.

• Keep out of reach of children.

• Certain materials or items, when stored under the product, will be subjected to radiant heat and could be seriously

damaged.

• Keep solid combustibles, such as building materials, paper or cardboard, a safe distance away from the product

as recommended by the instructions.

• Never use the product in spaces which do or may contain volatile or airborne combustibles, or products such as

gasoline, solvents, paint thinner, dust particles or unknown chemicals.

• During operation, this product can be a source of ignition. Keep the product area clear and free from combustible

materials, gasoline, paint thinner, cleaning solvents, and other ﬂammable vapors and liquids. Do not use the

product in areas with high dust content.

• Provide for adequate accessibility of the product. Keep the area around the product free from obstructions.

• Minimum product clearances from combustible materials: 3.3ft from the sides and 3.3ft from the top.

• This product is red hot during use and can ignite ﬂammables too close to the burner. Keep gasoline and other

ﬂammable liquids well away from the product.

• Check with your local ﬁre safety authority if you have questions about the product use.

• Carbon Monoxide (CO) poisoning produces ﬂu-like symptoms, watery eyes, headaches, dizziness, fatigue and

possibly death. You cannot see it and you cannot smell it. Carbon Monoxide is an invisible killer. If these symptoms

are present during operation of this product, get fresh air immediately.

Product Safety

• This product must be installed and the gas cylinder stored in accordance with the regulations in force.

• Do not obstruct the ventilation holes of the cylinder housing.

• Do not move the product when in operation.

• In case of violent wind particular attention must be taken against tilting of the product.

• Shut off the valve at the gas cylinder or the regulator before moving the product.

• Only use the gas regulator supplied with the product. The outlet pressure shall be according to the table in the

chapter “Speciﬁcations”.

• The tubing or the flexible hose must be changed if it is cut or worn or kinked.

• Use only the type of gas and the type of cylinder speciﬁed by the manufacturer.

• For use outdoors or in amply ventilated areas. An amply ventilated area must have:

– Walls on all sides, but no overhead cover.

– An overhead cover and no more than 2 side walls. These side walls may be parallel, as in a breezeway, or at right

angles to each other.

– The minimum of 30% of the surface area permanently open. The surface area is the sum of the walls surface.

Total surface area A+B+C+D 100 %

Wall surface area A+B+C max. 70 %

Open surface area D min. 30 %

• Close the valve of the gas cylinder or regulator after use.

• The use of this product in enclosed areas can be dangerous and is PROHIBITED.

• Provide adequate clearances around air openings into the combustion chamber.

• This product is a combustion appliance. All combustion appliances produce carbon monoxide (CO) during the

combustion process. This product is designed to produce extremely minute, non-hazardous amounts of CO if

used and maintained in accordance with all warnings and instructions. Do not block air ﬂow into or out of the

product.

• Never use inside the house, or other unventilated or enclosed areas.

• This product consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life.

• During set up, check all connections and ﬁttings for leaks using soapy water. Never use a ﬂame to check for leaks.

• Use as a heating product only. Never alter in any way or use with any device.

• This product contains small parts, which pose a choking hazard. Keep children away from small parts.

Gas Safety

• This product is fueled by LPG. LPG is invisible, odorless, and ﬂammable. An odorant is sometimes added to help

detect leaks which can be described as a “rotten egg” smell. The odorant can fade over time so leaking gas is not

always detectable by smell alone.

• LPG is heavier than air and leaking LPG will sink to the lowest level possible. It can ignite by ignition sources

including matches, lighters, sparks or open ﬂames of any kind many feet away from the original leak. Use only LPG

set up for vapor withdrawal.

• Store or use LPG in compliance with local ordinances and codes or with ANS/NFPA 58. Turn off LPG when not in

use.

• Keep all connections and ﬁttings clean. Make sure the LPG cylinder valve outlet is clean.

• Store the LPG cylinder outdoors in a well ventilated space out of reach of children. Never store the LPG cylinder

in an enclosed area (house, garage, etc.). If the product is to be stored indoors, disconnect the LPG cylinder for

outdoor storage.

• Never store LPG near high heat, open ﬂames, pilot lights, direct sunlight, other ignition sources or where

temperatures exceed 122°F.

• LPG vapors are heavier than air and can accumulate in low places. If you smell gas, leave the area immediately.

• Never install or remove the LPG cylinder while the product is lighted, near ﬂames, pilot lights, or other ignition

sources, or while the product is hot to the touch.

• Change the gas cylinder in an amply ventilated area, away from any ignition source (candles, cigarettes, other

ﬂame producing appliances).

Preparation

• Before beginning assembly of the product, make sure all parts are present. Compare parts with package contents

list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Contact

customer service for damaged or missing parts.

• Estimated assembly time: 90minutes for 2 adults.

• Required for assembly (not included):

– Soapy water.

Intended Use

• This product is intended for partially heating a patio.

• This product is intended for household use only. It is not intended for commercial use.

• This product is intended to be used in outdoor areas only. Do not use it indoors.

• No liability will be accepted for damages resulting from improper use or non-compliance with these instructions.

Before First Use

• Check for transport damages.

DANGER

Risk of suffocation! Keep any packaging materials away from children – these materials are a

potential source of danger, e.g. suffocation.

Assembly

Step 1:

Hardware used: Short bolt (B) x3, Bolt C x3

Attach the gas cylinder brackets (5) to the base plate (6).

Align the gas cylinder brackets with the eyelets in the base plate surrounding the large center hole.

Fasten the gas cylinder brackets to the base plate using 3 short bolts(B).

Turn the vertical portion of the brackets toward the middle of the base plate.

Tighten the short bolts using a wrench (H).

Insert 3 long bolts (C) into the nuts welded onto the gas cylinder brackets eyelets. Do not tighten the long bolts

completely (this will be done in step 13 when securing the gas cylinder).

Step 2:

Hardware used: Bolt A x8

• Attach 2 wheels (7) to the base plate (6) with 8 bolts (A).

• Pay attention to the direction of the wheels when attaching. Make sure the wheel brackets point towards the upper

side of the base plate (the side where the gas cylinder brackets are attached).

• For easy access, turn the base plate over before attaching the wheels.

Assembly

Step 3:

Hardware used: Screw E x20

103

• Assemble the lower frame. Align the eyelets at the bottom of lower supports (3) with the small eyelets on the

corners of the base plate (6). Fasten the lower supports to the base plate using 12 screws (E). Attach the middle

plate (10) at the top of the lower supports using 8 screws (E).

• The arrow sticker on the middle plate must point in the same direction as the corresponding sticker on the base

plate.

Assembly

Step 4:

Hardware used: Screw E x12

Slide the 4 upper supports (15) onto the lower supports (3).

Slide the corresponding opening of the upper supports onto the v-shaped rail of the lower supports.

The upper and lower support brackets need to ﬁt ﬂush. Secure the connections using 12screws(E).

Assembly

Step 5:

Hardware used: Screw E x8

• Attach the emitter (13) to the upper supports (15) using 8 screws (E).

NOTICE

Assembly step 5 may require a ladder. Follow safety precautions when working on a ladder.

Step 6:

Hardware used: Screw E x4

• Attach the control box (8) to the bottom of the middle plate (10) using 4 screws (E).

Assembly

Step 7:

WARNING

The black silicone ring (11) must be in place around the lower rim of the ﬂame tube (12) prior to

operating the product.

• Place the black silicone ring.

• Carefully install the ﬂame tube by guiding it up.

• Insert the upper end through the center hole in the plate of the emitter (13).

• Do not force the tube.

• Slide the ﬂame tube into place and settle it into the hole of the middle plate (10).

• Ensure that the tube is positioned properly to completely cover the center hole of the middle plate.

Assembly

Step 8:

Hardware used: Stud F x 3, Washer J x 6, Wing nut G x 3, Screw E x4, Guard bracket K x 4

• Attach the reﬂector (14) to the emitter (13). Screw the 3 reﬂector studs (F) into the top of the emitter, then slide

3 washers(J) onto the studs.

• Slide the reﬂector’s drilled holes onto the studs.

• Slide 3 washers onto the studs and secure the connection with 3 wing nuts (G).

• Attach the guard brackets (K) to all 4 sides of the emitter using 4 screws (E). Leave loosely attached until next step.

NOTICE

Assembly step 8 may require a ladder. Follow safety precautions when working on a ladder.

Assembly

Step 9:

• Assemble the guard screens (1).

• Hang the hooks of the guard screens onto the holes near the top, middle, and bottom of the upper supports (15).

• Secure the guard screens by tightening the screws (E) of the guard brackets (K) (attached to the emitter in previous

step).

Assembly

Step 10:

Hardware used: Screw E x16

• Attach the side panels (4) and the back panel (9) to the product using 4 screws (E) per panel.

• On the front side, insert the 4 screws (E) directly into the matching holes on the lower supports (3).

NOTICE

Do not cover the front, which is the side where the control knob of the control box faces.

Assembly

Step 11:

Hardware used: Screw D x2, Brace with chain (L) x 1

Attach the handle (16) on the outside of the door panel (2) and connect it with the brace with chain (L) on the

inside of the door panel using 2 screws (D).

Insert the tabs on the bottom of the door panel into the tab holes at the front of the base plate (6).

Attach the chain at the hook on the front of the control box (8).

Assembly

Step 12:

• Remove the door panel (2).

• Pry open the plastic cap of the sandbox (pre-installed on the base plate (6)).

• Fill the sandbox with sand or water, then securely close the plastic cap.

Step 13:

5 6

• Place an LPG cylinder (not included) on the base plate (6). Connect the regulator end of the gas hose with the

LPG cylinder (not included). Do not cross-thread. Secure the LPG cylinder with the gas cylinder brackets (5) by

tightening the 3 long bolts (C).

NOTICE

Only use a standard 20 lb LPG cylinder.

Information on Gas Cylinders

• Use this product only with a LPG vapor withdrawal supply system.

• Storage of the product indoors is permissible only if the cylinder is disconnected and removed from the product.

A cylinder must be stored outdoors in a well-ventilated area out of the reach of children. A disconnected cylinder

must have dust caps tightly installed and must not be stored in a building, garage or any other enclosed area.

• The pressure regulator and hose assembly supplied with the product must be used.

• Check the hose and regulator before use.

• Inspect the visible hose portion of the regulator before use. Check it completely at least annually.

• Replacements of the hose and regulator must be those speciﬁed by the manufacturer.

• The hose and regulator must be UL/CSA certiﬁed, the outlet pressure of the regulator must be according to the

table in the “Speciﬁcations” chapter. Suitable spare parts are available from specialist dealers.

• The installation must conform with local codes.

• A dented, rusted or damaged LPG cylinder may be hazardous and should be checked by your LPG supplier.

Never use a LPG cylinder with a damaged valve connection.

• The length of the hose cannot exceed 4.6 ft.

• The cylinder must have a listed overﬁlling prevention device.

• The cylinder must have a connection device compatible with the connection for the product.

• The cylinder must include a collar to protect the cylinder valve.

• Never connect an unregulated LPG cylinder to the product.

• Do not store a spare LPG cylinder under or near this product.

• Never ﬁll the cylinder beyond 80 % full.

• Place the dust cap on the cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap

on the cylinder valve that is provided with the cylinder valve. Other types of caps or plugs may result in leakage of

LPG.

Operation

Leak Check

WARNING

Risk of explosion!

• Perform all leak tests outdoors.

• Extinguish all open ﬂames.

• Never leak test when smoking.

• Do not use the product until all connections have been leak tested and do not leak.

1. Make 2 – 3 fl oz of soapy water (1 part liquid dish washing detergent and 3 parts water).

2. Apply several drops of the soapy water where the hose attaches to the regulator.

3. Apply several drops of the soapy water where the regulator connects to the cylinder.

4. Make sure all valves are closed.

5. Open the cylinder valve.

If bubbles appear at any connection, there is a leak.

1. Turn the cylinder valve off.

2. If the leak is at the hose/regulator connection, tighten the connection and perform another leak test. If bubbles

continue appearing, the hose/regulator connection should be replaced by a qualiﬁed service person.

3. If the leak is at the regulator/cylinder valve connection, disconnect, reconnect, and perform another leak check.

If you continue to see bubbles after several attempts, the cylinder valve is defective and should be replaced by a

qualiﬁed service person.

4. In the event of a gas leakage, the product shall not be used or, if alight, the supply shall be shut off and the product

shall be investigated and rectiﬁed before it is used again.

If no bubbles appear at any connection, the connections are secure.

NOTICE

Whenever gas connections are loosened or removed, you must perform a complete leak test.

5. Complete installation.

DANGER

Carbon monoxide hazard! For outdoor use only. Never use inside house, or other unventilated or

enclosed areas. This product consumes air (oxygen). Do not use in unventilated or enclosed areas

to avoid endangering your life.

CAUTION

Risk of injury! Do not attempt to operate until you have read and understand all general safety

information in this manual and all assembly is complete and leak checks have been performed.

Before turning the gas supply on:

1. Your product was designed and approved for outdoor use only. Do not use it inside a building, garage, or any

other enclosed area.

2. Make sure the surrounding area is free of combustible materials, gasoline, and other ﬂammable vapors or liquids.

3. Ensure that there is no obstruction to air ventilation. Be sure all gas connections are tight and there are no leaks.

4. Be sure the cylinder cover is clear of debris. Be sure any component removed during assembly or servicing is

replaced and fastened prior to starting.

Before Lighting

1. The product should be thoroughly inspected before use, and by a qualiﬁed service person at least annually. If

relighting a hot product, always wait at least 5 minutes.

2. Inspect the hose assembly for evidence of excessive abrasion, cuts, or wear. Suspected areas should be leak

tested. If the hose leaks, it must be replaced prior to operation. Only use the replacement hose assembly speciﬁed

by the manufacturer. The hose and regulator must be UL/CSA certiﬁed, the outlet pressure of the regulator must

be according to the table in the “Speciﬁcations” chapter.. Suitable spare parts are available from specialist dealers.

Lighting Instructions

1. Make sure the control knob is in the OFF position. Slowly open the LPG cylinder valve.

2. Press and turn the control knob to the PILOT position (counterclockwise). While holding the control knob in,

press the red piezoelectric ignition button several times in a row. You should hear a sparking or clicking sound of

the piezoelectric ignition. For the ﬁrst ignition, hold the control knob down for 30 seconds to remove air from the

tube before pressing the red piezoelectric ignition button.

3. Continue to hold in the control knob and check for the pilot ﬂame through the glass tube. If the pilot does not light,

press and turn the control knob clockwise to the OFF position. Repeat steps 2-3.

Figure 1 Figure 2

Page is loading ...

Amazon B0753P16BL User manual

Brand: Amazon

Model: B0753P16BL

Type: User manual

This manual is also suitable for

B0753PHV8Z

Download PDF

report

Amazon B0753P16BL User manual

This manual is also suitable for

Amazon B0753P16BL User manual

Other documents