miniSD
TM
& miniSDHC
TM
MEMORY CARDS
OPERATING MANUAL
SPECIFICATIONS
Dimension: 20.0 (W) x 21.5 (L) x 1.4 (T) mm
Durability:
10,000 mating cycles
Weight: Approx. 1g
Bending:
10N
Voltage Performance: 2.7 to 3.6 V
Torque:
0.10Nm
Temperature Performance::
-40°C to +85°C
Drop Test:
1.5m free fall
Clock Frequency: Up to 25MB/sec
Humidity Performance: 5% to 95% RH
NOTE: Specifications are subject to change without notice.
CONFIRMATION OF PARTS LIST
miniSD
TM
or miniSDHC
TM
Memory Card
miniSD
TM
Adapter or
miniSDHC
TM
Adapter
Plastic Case Manual
REMOVAL AND STOREAGE OF miniSD
TM
/ miniSDHC
TM
MEMORY CARD
1. Hold tight of the blister.
2. Turn the blister upside down with about an inch of distance between the blister and the table.
3. Use your fingers to push the edges of the plastic case.
4. Then plastic case with miniSD
TM
/ miniSDHC
TM
card and miniSD
TM
/ miniSDHC
TM
adapter will drop on the table
5. Unlock and open the lid of the plastic case.
6. Store or remove the miniSD
TM
/ miniSDHC
TM
card and miniSD
TM
/ miniSDHC
TM
adapter in the tray. Ensure the
miniSD
TM
/ miniSDHC
TM
card and miniSD
TM
/ miniSDHC
TM
adapter are placed properly on the tray before closing the
case.
Step 1
(miniSD
TM
Memory Card)
Step 1
(miniSDHC
TM
Memory Card)
Step 2 & Step 3
Step 4 & 5 (miniSD
TM
Memory Card)
Step 4 & 5 (miniSDHC
TM
Memory Card)
Step 6
(miniSD
TM
Memory Card)
Step 6
(miniSDHC
TM
Memory Card)
MICRODIA (USA)
Camden Ave., San Jose, CA 95120, USA
MICRODIA (UK)
Brickhill Drive, Manton Height, Bedford,
MK41 7QH, England
MICRODIA (HONG KONG)
International Sales Office
1371, HITEC, Trademart Drive, Kowloon Bay, Hong Kong
Tel: +852.2801.7813 Fax: +852.2801.7060
Website:
http://www.microdia.com
Email:
sales@microdia.com
PRECAUTIONS FOR HANDLING AND STORAGE
• Keep out of the reach of children. Get medical advice immediately if swallowed.
• Do not touch the interface pin directly by hands, metal or hard objects.
• Do not modify or disassemble the miniSD
TM
/ miniSDHC
TM
card.
• Do not wet, heat/fire, impact, drop or bend the miniSD
TM
/ miniSDHC
TM
.
• Do not use or store in a humid and dusty place; in hot place such as inside a hot car, under
a blazing sun, near fire, a stove, an air-conditioner outlet, etc.
• Do not expose to strong magnet fields, electrical noise and put near corrosive chemicals/gas.
This may cause damage through melting or the emission of heat/smoke or cause product
failure.
• Do not place in cooking appliances such as microwave ovens or high-pressure containers.
• Do not detach the label on the miniSD
TM
/ miniSDHC
TM
cards and adapter. Do not attach
other stickers/labels on the miniSD
TM
/ miniSDHC
TM
card and adapter.
DATA PROTECTION
• MICRODIA miniSD
TM
/ miniSDHC
TM
Memory Card comes pre-formatted. Make sure to
back up all the data on your miniSD
TM
/ miniSDHC
TM
card before formatting.
• Slide down Write-Protect Switch to “LOCK” for preventing record/edit the card. Unlock
the card before reading/writing data.
Unlock
Lock
• Do not remove miniSD
TM
/ miniSDHC
TM
card and switch off any equipment using the card
when data is being read, written and transferred. It can cause data to be destroyed.
• Insert the miniSD
TM
/ miniSDHC
TM
card firmly in the correct orientation. The product will
not operate correctly if it is inserted in an incorrect orientation or not inserted all the
way.
• Parental Guidance is needed when a child uses the miniSD
TM
/ miniSDHC
TM
cards. Teach
the child how to use and protect the product and insure that the child follows your
instructions.
/