KONICA Dynax 7xi User manual

MINOLTA

INSTRUCTION MANUAL

INTRODUCTION

The Minolta DYNAX 7xi is one of the most innovative AF SLRs available

For this reason, you are holding a large and rather intimidating owner's

manual. However, not everything will pertain to you immediately, so read

it in sections.

First, look over the parts diagrams and familiarize yourself with the

controls, their names, and their locations. This will be helpful later when

they are introduced in the manual and you learn about their functions.

Next, read Preparations, beginning on p.8. Follow along and attach the

strap, insert a battery, etc. Get used to holding the camera, working the

controls, and seeing the displays.

Then, begin where you must with anything new — The Basics. Read it well,

and you should then be ready to put the 7xi to work for you in the simplest

way possible. As you use the camera, you will begin to realize the power

of features such as:

• Expert system programming with fuzzy logic control

• High-Speed, Multi-Dimensional Predictive autofocus

• Expert Program Selection

• Graphic Display Viewfinder

• Creative Program Control

Operations in Detail and the Appendix are there for you to increase your

mastery over this unique camera and its innovative technology, and to help

you expand your control over the medium of photography.

IMPORTANT INFORMATION

The Minolta DYNAX 7xi was designed to work specifically with lenses,

flash units, and other accessories manufactured and distributed by

Minolta. We therefore caution users of this camera that the attachment

and/or use of incompatible products with the 7xi may result in

unsatisfactory performance or damage to the camera or its accessories.

To obtain optimum performance throughout the life of your DYNAX 7xi,

we recommend that you use only those lenses, flashes and other

accessories distributed by Minolta specifically for use with this camera.

1

TABLE OF CONTENTS

INTRODUCTION 1

NAMES OF PARTS 4

2

Neckstrap ...... 8

Eyepiece Cap 9

Lens 10

Attaching 10

Removing 11

Care of glass surfaces 11

Battery 12

Inserting 12

Battery-condition indicators 13

Battery Performance 14

Cold-weather operation 14

Film 15

Loading 15

Automatic/manual film speed setting 18

Automatic/manual rewind 20

Holding the Camera 22

Taking Pictures 23

Camera-Shake Warning 25

Autofocus 26

Focus Signals 27

Focus Lock 28

Programmed Autoexposure 29

Creative Program Control 31

PA 32

Ps 35

OPERATIONS IN DETAIL

Main Switch and Eye-start 39

Focusing Details 40

Autofocus illuminator 40

Local AF area selection 41

Special focusing situations 43

Manual focus 44

Exposure Details 46

Changing exposure mode 46

Aperture priority 48

Shutter priority 50

Manual exposure 52

Metering modes 54

Exposure compensation 56

AEIock 58

Self-timer 59

Bulb 60

Flash System 62

Flash modes 62

P mode flash 64

A, S, and M mode flash 65

Slow-shutter sync flash 68

Remote off-camera TTL flash 70

Film drive 74

Autozoom 76

Auto stand-by zoom 76

Image-size lock 78

Wide-view mode 80

APPENDIX

Lens Aperture and Depth of Field 84

Shutter Speed and Moving Subjects 87

Composition 88

Accessory Information 90

Care and Storage 92

Troubleshooting 94

Technical Description 95

Quick Reference Guide 98

Names of Parts/Body

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11

12

Grip sensor

AF illuminator/self-timer light

Wide-view mode button

Strap eyelet

Front control dial

Shutter-release button

Card on/off button

Body data panel

Accessory shoe

Program-reset button

Main switch

Flash pop-up button

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

24.

25.

Back-cover release

Lens release

Focus-mode switch

Mounting index

Mirror*

Lens contacts*

Film chamber

Eyepiece sensor

Eyepiece cup

AE Lock button

Rear control dial

Function button

Film window

4

Card Door

*Do not touch

5

26. Pressure Plate*

27. Accessory-back contacts*

28. Card door

29. Remote-control terminal

30. Battery-cover release

31. Film-leader index

32. Sprocket

33. Tripod socket

34. DX contacts*

35. Self-timer/Drive mode button

36. Flash-mode button

37. Rewind button

38. ISO button

39. Card-adjust button

40. Card-eject slide

Names of Parts/Body LCD

1. Exposure-mode indicators

2. Wide/Local focus indicator

3. Flash-mode indicators

4. Self-timer indicator

5. Drive-mode indicators

6. Frame counter

7. Film-transport signals

8. Film-cartridge mark

9. Aperture/Exposure Adjustment/Card setting displays

10. Card indicator

11. Exposure-adjustment indicator

12. Metering-mode indicators

13. Shutter-speed/film-speed/card name displays/

local-AF-area indicators

14. Exposure-adjustment reminder

15. Selectable Setting Pointers

16. Battery-condition indicator

17. Film-speed mark

6

Names of Parts/Viewfinder Screen

1. Image-size-lock indicator

2. Dial-function indicators

3. Wide-view indicator

4. Film-frame indicator

5. AF-area indicator

6. Local-AF-area indicator

7. Spot-metering area

8. Manual-focus indicator

9. Depth index

10. Action index

11. Panorama indicator

12. Image control index

Names of Parts/Viewfinder Data Panel

1. Flash-on indicator

2. Flash-mode indicator

3. Camera-shake warning

4. Focus signals

5. Exposure-mode indicators

6. Shutter-speed/Film-speed display

7. Exposure Signals/Exposure Adjustment indicator

8. Aperture/Exposure Adjustment display

9. AEL indicator

7

NECKSTRAP

A neckstrap is supplied with your camera. Attach it as shown below.

a

An eyepiece cap is also included on the strap. It fits over the eyepiece to

prevent stray light from entering the camera and affecting the exposure

during situations in which you are not looking through the viewfinder

when the shutter releases (ie, self-timer photographs or bulb exposures).

An accessory shoe cap protects the contacts on the camera's accessory

contacts from dust and dirt. When you are using a flash or other accessory,

slide the accessory shoe cap into the eyepiece cap for safekeeping.

9

EYEPIECE CAP

1. Remove body cap and rear lens cap as shown.

2. Align the red bead on the lens barrel with the red dot on the camera's

lens mount. Gently insert the lens into the mount and turn the lens

clockwise until it locks in place with a click.

• If no lens is attached to the camera, if the lens is not attached properly,

or if the AZ/MZ switch on an xi-Series lens is set to MZ, "--" will appear in

the body data panel and in the aperture display of the viewfinder data panel

when Eye-Start activates the camera (below).

10

To attach:

To remove:

1. While pressing the lens release, turn the lens counterclockwise until it

stops. Lift the lens out of the mount.

2. Immediately attach the rear cap to the lens and the body cap or another

lens to the camera. This will protect the camera interior, lens contacts, and

lens elements.

- Be carefu!

• Do not to force the lens onto the body if it does not turn smoothly.

• Never touch anything inside the camera, especially the lens contacts

and mirror.

Care of Glass Surfaces

• Never touch any lens surfaces (including the eyepiece) with your

fingers. If a lens becomes dirty, first gently clean it with a lens brush. Then,

if necessary, moisten a sheet of lens tissue with one drop of lens-cleaning

fluid and, starting from the center of the lens, wipe the glass in a circular

motion.

• Never lift the mirror or touch its surface, as this may impair its alignment

or scratch its face. Dust on the mirror's surface will not affect meter

readings or picture quality. If it is distracting, have the camera cleaned at

an authorized Minolta service facility.

11

The camera uses a 6-volt 2CR5 lithium battery which supplies power for

all camera operations. If you are using an xi-Series lens, the camera battery

also supplies power to the lens zoom motor.

Installation

1. With the main switch in the LOCK position, slide the battery cover

release in the direction indicated to open the battery cover.

2. Insert the battery according to the marks on the inside of the chamber

cover.

3. Snap the cover closed.

• Sometimes it helps to wipe the battery terminals with a clean, dry cloth

in order to ensure proper contact.

CAUTION

• Read and follow all warnings and instructions supplied by the battery

manufacturer.

• Do not attempt to disassemble, recharge, or short-circuit the battery.

Do not subject it to high temperatures or fire. The battery may explode

and cause severe burns.

• Keep batteries away from children.

12

Battery-condition Indicators

At various times during operation, one of the following indicators will

appear in the body data panel.

Display Indication

1. Full-battery symbol

appears for 4 sec.

after you turn camera

on.

2. Low-battery symbol

appears for 4 seconds

after you turn camera

on.

3. Low-battery symbol

blinks while it

appears with other

operating indicators

at any time during use.

4. Blinking

low-battery symbol and

appears, or no

display appears at

all, and shutter locks

Meaning

Power is sufficient.

Power is sufficient, but

getting low. Keep a

fresh battery handy.

Camera can be

operated, but power is

extremely low. The

battery will need to

be changed soon.

Power is insufficient

for operation.

Replace the battery or

check that the battery

is inserted correctly.

• If no display appears when the main switch is set to ON, double-check

that the battery is inserted correctly before inserting a fresh one.

13

Battery Performance

The 6-volt 2CR5 lithium battery should provide sufficient power for

shooting approximately 50 rolls of 24-exposure film without flash. These

figures are based on Minolta's standard test method using a fresh battery

at 68°F (20°C). Actual battery performance will depend on how you use the

camera. If you install a new battery that has been in prolonged storage,

battery performance may vary.

Cold-Weather Operation

Lithium batteries provide excellent performance in cold weather.

However, if you plan to shoot many rolls of film outdoors at temperatures

near or below 32° F (0°C), we recommend that you carry the camera inside

your coat while you are not shooting, to keep it warm. You may also want

to carry a spare battery in your pocket so that you can change the camera

battery if necessary. Do not discard a cold battery. After it warms up, it will

regain some of its charge.

14

Loading Film

Before you load film, always check the body data panel. If the film cartridge

is displayed, do not open the back cover. Check the film window and frame

counter to verify the type of film in the camera and the number of frames

remaining. (See p. 20 for instructions on rewinding a partially exposed roll of

film.)

• Before you load film for the first time, remove and discard the protective

plastic cover over the shutter.

• Always load film in subdued or shaded light.

-NEXT PAGE-

15

1. Open the back cover by sliding the back-cover release downward.

2. Place the film cartridge into the film chamber as shown above and extend

the leader between the guide rails until the tip is just past the film-leader

index. Make sure the holes in the film's lower edge are engaged by the

sprocket teeth.

RIGHT

WRONG

RIGHT

WRONG

• Make sure the film leader is shaped correctly, otherwise the film may

not wind properly. Trim a torn or crimped film tip so that it looks like the

correct one pictured above left.

• If the film extends too far, gently push the excess back into the cartridge.

• NEVER TOUCH THE SHUTTER CURTAIN WITH YOUR FINGERS OR

WITH THE FILM TIP. Its precision design makes it extremely sensitive to

pressure.

-NEXTPAGE-

16

3. Close the back cover and move the main switch to ON. The camera will

automatically advance the film to the first frame and 1 will appear in the film

counter.

• If the film is loaded incorrectly, 0 will blink in

the frame counter and the shutter will remain

locked. Open the back cover and repeat steps 2

and 3.

• If you turn the main switch to ON before you load film, to not touch the

grip sensor during the above procedures.

17

Manual Film Speed Setting

If you are using a non-DX-coded film or if you wish to override the

automatic setting, you must manually set the film speed. The camera will

initially set non-DX-coded film to the ISO of the previous roll; initially this

value is set to 100.

1. Load the film and close the back cover.

2. Open the card door and press the ISO button.

-NEXT PAGE-

18

If you use DX-coded film between ISO 25 and

5000, the camera will automatically set the

correct film speed. The film speed setting will be

displayed in the body data panel for 4 sec. after

you load the film.

Automatic Film Speed Setting

Page is loading ...

KONICA Dynax 7xi User manual

This manual is also suitable for

KONICA Dynax 7xi User manual

Related papers

Other documents