AIRE BY MINKA F519L-PN User manual

Brand: AIRE BY MINKA

Model: F519L-PN

Category: Household fans

Type: User manual

This manual is also suitable for

U.S. Patent: 7,008,192

INSTRUCTION MANUAL WARRANTY CERTIFICATE

CONCEPT II 52”

This product is protected by United States Federal and/or State Law including Patents, Trademark, and/or Copyright Laws.

Patents, Trademark, and/or Copyright Laws.

The Minka-Aire® warranty is for one (1) year from the date of purchase from an authorized Minka-Aire® dealer.

This warranty is only valid to the original purchaser or user against all defects in material and workmanship (light bulbs

excluded) for one (1) full year. Additionally, Minka-Aire® warrants the motor only for the lifetime of the Minka Aire ceiling

fan (excluding wall controls and electrical components), to the original purchaser or user.

* The warranty is voided with the use of any non- Minka-Aire®electrical devices, E.g., wall controls or electrical dimmer switches, etc…

* The warranty is void once the original purchaser or user ceases to own the fan or the fan is moved from its original point of installation.

* The warranty is void with the use of any hanger bracket (non-Minka Aire or non-fan specific) other than the hanger bracket supplied & installed

with this specific fan.

Date Purchased Store Purchased Model Number Serial Number

F519L

Warranty Service Information

To obtain warranty service during the warranty period, the purchaser should return the fan with the sales receipt to the original place of

purchase. The authorized Minka-Aire® dealer, at its sole discretion, will either repair or replace the fan after verifying the legitimacy of the warranty

claim. Replacement is subject to availability of the same model. If the model is unavailable it will be replaced by one of equal value. This is a

limited warranty; the original purchaser or user is responsible for the cost of removal and reinstallation of repaired or replacement product.

To obtain the name of the Minka-Aire® authorized dealer nearest you call the Minka-Aire® customer care department at 1-800-307-3267, or

contact Minka-Aire® through www.minkagroup.net and select FAQ to answer any questions or if you require additional assistance submit the

question form found there.

CONTENTS

INSTALLING THE LED LIGHT KIT & GLASS SHADE .................

OPERATING THE REMOTE CONTROL........

......................................

CARE OF YOUR FAN................................................................................

TROUBLESHOOTING............................................................................

SPECIFICATIONS.....................................................................................

LISTED

E75795

1151 W. Bradford Court, Corona, CA 92882 For Customer Assistance Call: 1-800-307-3267

SAFETY RULES....................................................................................

PACKAGE CONTENTS.....................................................................

INSTALLING THE MOUNTING BRACKET..............................

ELECTRICAL CONNECTIONS.......................................................

FINISHING THE INSTALLATION................................................

BLADE INSTALLATION...................................................................

SAFETY RULES

1. Before you begin installing the fan, shut power off at the circuit breaker of the fuse box.

2. Be cautious! Read all instructions and safety information before installing your new fan. Review accompanying assembly diagrams.

3. Make sure that all electrical connections comply with local codes, ordinances, or National Electrical Codes. Hire a qualified electrician or consult a

do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring.

4. Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the

floor and 18 inches from the tip of the blades to the wall.

5. If you are mounting the fan to a ceiling fan outlet box, use a U.L. Listed metal octagonal outlet box marked "Acceptable for Fan Support". Secure the

box directly to the building structure. The outlet box and its support must be able to support the moving weight of the fan (at least 50 pounds) Do

not use a plastic box.

6. Caution: To reduce the risk of injury use only the screws provided with the outlet box in conjunction with the lock washers provided with the fan.

7. If you are mounting the fan to a joist, make sure it is able to support the moving weight of the fan (at least 50 pounds).

8. After you install the fan, make sure that all mounting components are secured to prevent the fan from falling.

9. Do not insert anything into the fan blades while the fan is operating.

10. Turn the fan off and wait for the blades to stop completely before performing any maintenance or cleaning.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL INJURY, MOUNT FAN ONLY TO A U.L. LISTED OUTLET BOX OR SUPPORTING SYSTEM MARKED

ACCEPTABLE FOR FAN SUPPORT AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX IN CONJUCTION WITH THE LOCK WASHERS PROVIDED WITH

THE FAN. MOST OUTLET BOXES COMMONLY USED FOR FAN SUPPORT OF LIGHTING FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND NEED TO BE

REPLACED. CONSULT A QUALIFIED ELECTRICIAN IF IN DOUBT.

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE HOLDERS WHILE INSTALLING, BALANCING THE BLADES OR CLEANING THE FAN. DO NOT

INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.

TO REDUCE THE RISK OF FIRE OR ELECTRONIC SHOCK, THIS FAN ONLY CAN USE CFR-3T SOLID-STATE SPEED CONTROL WITH TR111A-1 WALL CONTROL ONLY.

NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may

occur. It must be understood that common sense, caution and care are factors which can not be built into this product. These factors must be

supplied by the person (s) installing, caring for and operating the unit.

NOTE: READ AND SAVE ALL INSTRUCTIONS!

1. Fan Blades (3)

2. Mounting bracket

3. Fan motor/housing ass'y

4. 14W LED light kit

5. Glass shade

6. Metal light cover (for optional use)

7. Receiver with 6 wire nuts

8. Hand held remote with 2 Screws

9. Balancing kit

A. Mounting hardware:

#8 x 3/4" Machine screws (2)

#10 x 1.5" Wood screws (4)

Flat washers (6)

Lock washers (4)

Wire nuts (3)

Washers (2)

B. Blade removal tool

PACKAGE CONTENTS

Unpack your fan and check the contents. You should have the following items:

Tools Required: Phillips screw driver; slotted screw driver; step-ladder; wire cutters; electrical tape.

INSTALLING THE MOUNTING BRACKET

WARNING: All of the parts, hardware and components such as the hanger bracket and hanger ball have

been provided for your safety and the proper installation of your new ceiling fan. The use of other parts,

hardware or components not supplied by Minka Aire

with the fan will void the Minka Aire

Warranty.

REMEMBER To turn off the power. Follow the steps below to hang your fan properly.

Step 1. Attach the mounting bracket to the outlet box with two screws and washers provided. Make sure

the bracket is tight and secured. (Fig. 1)

Step 2. Lift fan into position by hanging the motor assembly onto the hook from the ceiling mounting

bracket allowing it to hang freely. (Fig. 1)

FIG. 1

ELECTRICAL CONNECTIONS

WARNING:

To avoid possible electrical shock be sure electricity is

turned off at the main fuse or breaker box before wiring.

NOTE: The Aire Control

System is equipped with a learning frequency

function which has 256 code combinations to prevent potential

interference from other remote units. The frequency on your Receiver

and Transmitter units have been preset at the factory. (Fig. 2) No

frequency change is necessary, should you desire to install another fan

within the same home or area with a seperate frequency code please see

the "frequency interference" troubleshooting section of this instruction

manual to learn how to change the frequency.

Note: The receiver has been attached the motor housing and

wired for ease of installation. (Fig. 3)

NOTE: If your ceiling fan features an UP Light: Connect the ORANGE wire

from the fan to the ORANGE wire marked "For Up Light" from the

Receiver. Otherwise disregard this step and proceed to secure all wire

connections with the plastic wire nuts provided. (Fig. 4)

Note: Fan must be installed from a maximum distance of 40 feet from

the transmitting unit for proper signal transmission between the

transmitting unit and the fan's receiving unit.

Fig. 2

Fig. 3

RECEIVER

MOUNTING

BRACKET

Step 1. Receiver to House Supply Wires Electrical Connections:

Connect the WHITE wire (Neutral) from the outlet box to the WHITE

wire marked "AC in N" from the receiver. Connect the BLACK wire

(Hot) from the outlet box to the BLACK wire marked "AC in L" from

the receiver. Secure all wire connections with the plastic wire nuts

provided. (Fig. 4)

Step 2. Connect the fans ground wire (green) located on the mounting

bracket to the household ground wire. Secure wire connection with the

plastic wire nut provided. (Fig. 4)

After all splices are made, check to make sure there are no loose

strands. As an additional precaution we suggest to secure the plastic

wire connectors to the wires with electrical tape.

WHITE (NEUTRAL)

GREEN OR BARE

COPPER (GROUND)

WHITE ("AC IN N")

WHITE ("TO MOTOR N")

GROUND-

(GREEN)

(CONNECT TO

GROUND WIRE ON

HANGER BRACKET

IF NO HOUSE

GROUND WIRE

EXISTS.)

OUTLET BOX

BLACK (HOT)

BLACK ("AC IN L")

BLACK ("TO MOTOR L")

RECEIVER

BLUE (FOR LIGHT)

ORANGE

(FOR UPPER LIGHT)

BLACK (MOTOR)

ORANGE

(FOR UPPER LIGHT)

Fig. 4

FINISHING THE INSTALLATION

Step 1. Loosen two of the four screws from the mounting

bracket and remove the other two.

Step 2. Remove the motor assembly from the mounting

bracket hook and engage the key holes to the two screws

previously loosened.

Step 3. Install the two screws previously removed and

tighten all four screws.

Fig. 5

Fig 6

THE FOLLOWING OPERATION MUST BE ACCOMPLISHED BEFORE INSTALLING THE GLASS SHADE.

Step 1. Insert the blades into the motor housing blade slots, push blade until it stops. You should be

able to hear the inside safety pin drop into the blade hole to secure the blade in place. (Fig. 6)

CAUTION: Re-check each blade to make sure all blades are secured to the motor by holding the blade

from the tip and gently pulling it outwards. The blades should be snug to the motor housing

without any up, down or sideways play.

All blade sets are grouped by weight. Because plastic injection varies in density, the fan may wobble

even though the blades are weight matched.

BLADE REMOVAL

In the event that the blades need to be removed, use the blade removal tool included with your fan.

Remove the blades by pulling the safety pin via the opening above the blade in the motor housing

as shown. (Fig. 7)

BLADE INSTALLATION

Fig 7

Fig. 8

CAUTION: Before starting installation, make sure power is turned off at the circuit breaker.

If you do not plan to install the light kit with your fan at this time, skip step 1, 2 & 3.

1. Remove 1 of 3 screws from the mounting plate and loosen the other 2 screws. (Do not remove)

2. While holding the LED light kit under the fan motor assembly, make the 2-pin wire connections: -

- White to white - Black to black

3. Place the key holes in the LED light kit over the two mounting screws previously loosened from the

mounting plate. Turn the LED light kit until the LED light kit locks in place at the narrow section of the

key holes. Secure by tightening the two screws previously loosened and the one previously removed.

(Fig. 8)

4. Raise the glass shade (or metal light cover) up against the mounting plate and secure it to the fan by

turning the glass shade clockwise until snug. DO NOT OVERTIGHTEN. (Fig. 8)

NOTE: The metal light cover included with your fan is an option to replace the glass for the light in the

event that you prefer not to use the light feature of your fan. The metal light cover is not necessary for the

light operation; it can be saved for later use if desired.

INSTALLING THE LED LIGHT KIT & GLASS SHADE

GLASS

SHADE

SCREWS

MOUNTING

PLATE

LED LIGHT KIT

OPERATING THE REMOTE CONTROL/WALL CONTROL

Restore Power to Ceiling Fan.

A. Buttons:

These buttons are used to set the fan speeds as follows;

= Low Speed

= Medium Speed

= High Speed

B. Button:

This button turns the fan off.

C. Button:

These buttons turn the light ON or OFF and also control

the brightness settings of the light. The following

instructions apply to ceiling fans that feature a DOWN

light ( button) only or ceiling fans that feature an UP

light ( button) and a DOWN light ( button) that are

controlled independent of each other;

Press and release the button for the desired light to turn

the light ON or OFF. Press and hold the button to set the

desired light brightness. The light will cycle between

bright and dim settings as long as the button is pressed.

The light key has an automatic auto-resume feature that

allows the light to remain at the same brightness as the

last time it was turned off.

D. OFF-ON Slide Button (Wall Control Fans Only)

This button turns the power Off and On to the Fan and

Light(s).

E. Button: (Full Function Remote Control Units Only)

This button is used to change the direction of the

rotation of the blades; forward for warm weather or

reverse for cool weather.

Hold the reverse button for a minimum of 3 seconds and

release once you hear a faint "click" in the receiver area,

this sound alerts you that the function has been

received. The fan must be in operation to activate the

reverse feature.

Remote Control only: Install a A23 12 volt battery (included). To prevent damage to transmitter remove the battery if not used for long periods of time.

Speed settings for warm or cold weather

depend on factors such as room size, ceiling

height and number of fans.

NOTE: To change the direction of the rotation of

the blades the fan must be in operation mode.

Warm Weather (forward)

A DOWNWARD airflow creates a cooling effect

as shown in Figure 9. This allows you to set your

air conditioner on a warmer setting without

affecting your comfort.

Cool Weather (Reverse)

An UPWARD airflow moves warmer air off the

ceiling area as shown in Figure 10. This allows

you to set your heating unit on a cooler setting

without affecting your comfort.

FIG. 9

FIG. 10

WINTER OPERATION

(

CLOCKWISE DIRECTION)

SUMMER OPERATION

(COUNTERCLOCKWISE DIRECTION)

Here are some suggestions to help maintain your fan.

1. Because of the fan's natural movement some connections may become

loose. Check the support connections, brackets and blade attachments

twice a year. Make sure they are secure. (It is not necessary to remove

fan from the ceiling).

2. Clean your fan periodically to help maintain its new appearance over

the years. Use only a soft brush or lint free cloth to avoid scratching the

finish. Plated finishes are sealed with lacquer to minimize discoloration

or tarnishing. Do not use water when cleaning, this could damage the

motor, wood blades or possibly cause an electrical shock.

3. Use a lint free lightly damp cloth or duster to remove dust from the

blades.

4. There is no need to oil your fan. The motor has permanently lubricated

bearings.

5. If your fan is provided with glass shades, clean with lukewarm soapy water

and a soft cloth or sponge. DO NOT IMMERSE GLASS SHADES IN HOT WATER.

DO NOT PUT GLASS SHADES INTO AN AUTOMATIC DISHWASHER.

CARE OF YOUR FAN

WARNING!

MAKE SURE THE POWER IS OFF AT THE

ELECTRICAL PANEL BOX BEFORE YOU ATTEMPT

ANY REPAIRS. REFER TO THE SECTION,

"ELECTRICAL CONNECTIONS".

TROUBLESHOOTING

SYMPTOM

Fans/Light Turn On

and Off Unexpectedly

SOLUTION

This is caused by

interference, change the

code frequency from the

transmitter, and follow

the instructions from

Section 5 again to

operate your transmitter

and fan.

SYMPTOM

Fan Sounds Noisy

SOLUTION

Allow a 24-hour "break in" period.

Most noises associated with a

new fan will go away during this

time.

Make sure the screws that attach

the fan blade holder to the motor

hub is tight.

Make sure outlet box is secured

to building structure, if

necessary use the wood screws

provided to further secure

outlet box to joist.

Make sure hanger bracket is

secure to the outlet box, screws

are tight.

SYMPTOM

Fan will not start

SOLUTION

Check to make sure the wall switch is

turned on.

Check circuit fuses or breakers.

Caution! Make sure the power is turned

off before performing the following steps.

Remove canopy and check wire

connections.

Check wall control transmitter connections

(if applicable).

Note: Fan must be installed at a maximum

distance of 40 feet from the transmitting

unit for proper signal transmission

between the transmitting unit and the

fan's receiving unit.

SYMPTOM

Fan Wobble

SOLUTION

NOTE: All blade sets are grouped by

weight. Because wood and plastic

blades vary in density, the fan may

wobble even though blades are

matched.

Make sure outlet box is secured to

building structure, if necessary use the

wood screws provided to further secure

outlet box to joist.

Make sure hanger bracket is secure to the

outlet box, screws are tight.

If a Balancing kit is provided follow the

instructions included with the balancing

kit to help correct any excessive wobble.

Page is loading ...

AIRE BY MINKA F519L-PN User manual

Brand: AIRE BY MINKA

Model: F519L-PN

Category: Household fans

Type: User manual

This manual is also suitable for

Download PDF

report

AIRE BY MINKA F519L-PN User manual

This manual is also suitable for

AIRE BY MINKA F519L-PN User manual

Related papers

Other documents