ECS X58B-A3 SLI User manual

Preface

Copyright

This publication, including all photographs, illustrations and software, is protected

any of the material contained herein, may be reproduced without written consent of

the author.

Version 1.0

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any

particular purpose. The manufacturer reserves the right to revise this publication and

to make changes from time to time in the content hereof without obligation of the

manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective

owners and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful inter-

ference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment onto an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits governing

this device. Changes or modifications not expressly approved by the system’s manu-

facturer could void the user’s authority to operate the equipment.

ii

Preface

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the

following conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received, including interfer-

ence that may cause undesired operation

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur

le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Describes features of the

motherboard.

Go to

H

page 1

Describes installation of

motherboard components.

Go to

H

page 7

Provides information on us-

ing the BIOS Setup Utility.

Go to

H

page 25

Go to

H

Describes the ATI

Crossfire

TM

Technology

page 45

Describes the motherboard

software

Go to

H

page 51

Chapter 2

Installing the Motherboard

Chapter 1

Introducing the Motherboard

Chapter 3

Using BIOS

Chapter 4

Using the Motherboard Software

Chapter 5

ATI Crossfire

TM

Technology Support

Describes the Intel

®

Matrix

Storage Manager RAID Con-

figurations

Chapter 6

Intel

®

Matrix Storage Manager

RAID Configurations

Go to

H

page 55

iii

Chapter 2

7 7

7

Installing the Motherboard 7

Safety Precautions............................................................................7

Choosing a Computer Case.............................................................7

Installing the Motherboard in a Case............................................7

Checking Jumper Settings...............................................................8

Setting Jumpers.......................................................................8

Checking Jumper Settings.......................................................9

Jumper Settings.......................................................................9

Installing Hardware...................................................................10

Installing the Processor.........................................................10

Installing Memory Modules...................................................12

Expansion Slots......................................................................15

Connecting Optional Devices................................................17

Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive...19

Connecting I/O Devices.................................................................21

Connecting Case Components.....................................................22

Front Panel Header...............................................................24

TT

T

ABLE OF CONTENTSABLE OF CONTENTS

ABLE OF CONTENTS

Preface i

Chapter 1 1

Introducing the Motherboard 1

Introduction...................................................................................1

Feature............................................................................................2

Specifications................................................................................4

Motherboard Components..........................................................5

Chapter 3 25

Using BIOS 25

About the Setup Utility........................ ......................................... 25

The Standard Configuration...................................................25

Entering the Setup Utility.......................................................25

Resetting the Default CMOS Values......................................26

Using BIOS......................................................................................27

Standard CMOS Setup..........................................................28

Advanced Setup.....................................................................30

Advanced Chipset Setup.........................................................33

Integrated Peripherals...........................................................34

Power Management Setup.....................................................35

PCI/PnP Setup.......................................................................36

iv

PC Health Status...................................................................37

M.I.B (MB Intelligent BIOS).................................................39

Load Default Settings............................................................42

Supervisor Password............................................................42

User Password......................................................................43

Save & Exit Setup..................................................................43

Exit Without Saving...............................................................43

Updating the BIOS................................................................44

Chapter 4

45 45

45

Using the Motherboard Software 45

About the Software CD-ROM......................................................45

Auto-installing under Windows XP/Vista..................................45

Running Setup.......................................................................46

Manual Installation........................................................................50

Utility Software Reference........................................................50

Chapter 5

51 51

51

ATI CrossFire

TM

Technology Support 51

Requirements..................................................................................51

Installing CrossFire

TM

graphics cards.........................................52

The Catalyst

TM

Control Center Dialog Box.................................53

View.......................................................................................53

To Enable CrossFire

TM

..........................................................53

Chapter 6

55 55

55

Intel

®

Matrix Storage Manager RAID Configurations 55

Before creating a RAID set...........................................................55

Entering Intel

®

Matrix Storage Manager RAID BIOS utility...56

Creating a RAID set.......................................................................57

Deleting a RAID set.......................................................................59

Resetting disks to Non-RAID......................................................60

Exiting Setup...................................................................................60

Bootblock Initialization Code Checkpoints 61

POST Code Checkpoints 62

1

Introducing the Motherboard

Chapter 1

Introducing the Motherboard

Introduction

Thank you for choosing the X58B-A2 motherboard. This motherboard is a high

performance, enhanced function motherboard designed to support the LGA1366

socket Intel

®

Core

TM

i7 processor for high-end business or personal desktop markets.

The motherboard incorporates the Intel

X58 Northbridge (NB) and Intel ICH10R

Southbridge (SB) chipsets. The Northbridge supports Intel

®

QuickPath Interconnect

(Intel

®

QPI) of 4.8 GT/s to 6.4 GT/s supporting different routing lengths. The memory

controller supports DDR3 memory DIMM frequencies of 1333/1066/800. It sup-

ports six DDR3 sockets with up to maximum memory of 24 GB. DDR3 Maximum

memory bandwidth of 32 GB/s in triple-channel symmetric mode assuming DDR3

1333 MHz. High resolution graphics via two PCI Express slots, intended for Graphics

Interface, is fully compliant to the PCI Express Base Specification revision 2.0.

Additionally, one PCI Express x4 slot is supported, fully compliant to the PCI

Express Base Specificaiton revision 2.0 as well. It supports the ATI CrossFire

TM

Technology that allows you to install GPU graphics cards.

The ICH10R Southbridge on this motherboard supports one PCI slot which is PCI

v2.3 compliant. In addition, two PCI Express x1 slot is supported, fully compliant to

the PCI Express Base Specification revision 1.1. It implements an EHCI compliant

interface that provides 480 Mb/s bandwidth for twelve USB 2.0 ports (six USB ports

and three USB 2.0 headers support additional six USB ports). The Southbridge sup-

ports six SATA ports with maximum transfer rate up to 3.0 Gb/s each. It supports

Intel

®

Matrix Storage Technology, providing both AHCI and RAID 0, 1, 5 and 10

configuration.

The motherboard is equipped with advanced full set of I/O ports in the rear panel,

including PS/2 mouse and keyboard connectors, one CLR_CMOS button, two eSATA

ports, one 1394a port, one LAN port, six USB ports, one optical SPDIFO port and

audio jacks for microphone, line-in and 8-ch line-out.

In addition, this motherboard comes with an LED for debug, a power on button, a

reset button and a CLR_CMOS button. The processor can be overclocked when CPU

Over-clocking Func. is set to Enabled in M.I.B (MB Intelligent BIOS).

2

Introducing the Motherboard

Feature

• Accommodates Intel

®

Core

TM

i7 processor

• Intel

®

QuickPath Interconnect (Intel

®

QPI) of 4.8 GT/s to 6.4 GT/s support-

ing different routing lengths

The motherboard uses an LGA1366 type of Intel

®

Core

TM

i7 processor that

carries the following features:

Processor

The X58 Northbridge (NB) and ICH10R Southbridge (SB) chipsets are based on

an innovative and scalable architecture with proven reliability and performance.

Chipset

ICH10R

(SB)

• Enhanced DMA Controller, interrupt controller, and timer func-

tions

• Compliant with PCI Express Base Specification, revision

1.1

• Compliant with PCI v2.3 specificaiton

• Compliant with SATA 3.0 Gb/s Host Controller

• Integrated USB 2.0 Host Controller supporting up to twelve

USB 2.0 ports

• Supports Intel

®

Matrix Storage Technology, providing both

AHCI and RAID 0, 1, 5 and 10 configuration

• Supports DDR3 1333/1066/800 DDR3 SDRAM with Triple-channel ar-

chitecture

• Accommodates six unbuffered DIMMs

• Up to 4 GB per DIMM with maximum memory size up to 24 GB

• Supports 1 Gb, 2 Gb and 4 Gb DDR3 DRAM technologies for x8 and x16

devices (It is not recommended to use 512 Mb DDR3 memory device on

this motherboard)

Memory

X58 (NB)

• One full width Intel

®

QPI (QuickPath Interconnect) link inter-

face

• Packetized protocol with 18 data/protocol bits and 2 CRC

bits per link per direction, 4.8 GT/s to 6.4 GT/s suporting

different routing lengths

• Support for 64-byte cacheline size

• Two x16 PCI Express Gen2 ports each supporting up to 8

GB/s direction peak bandwidth

• An additional x4 PCI Express Gen2 port configuration to 2

x2 interface

Audio

• Compliant with Intel High Definition Audio Codec

• 7.1 channel audio CODEC

Onboard LAN

• Realtek Giga LAN Controller

3

Introducing the Motherboard

The motherboard comes with the following expansion options:

• Two PCI Express x16 slots for Graphic Interface

• One PCI Express x4 slot

• Two PCI Express x1 slots

• One 32-bit PCI v2.3 compliant slot

• Six 7-pin SATA connectors

Expansion Options

The motherboard has a full set of I/O ports and connectors:

Integrated I/O

• Two PS/2 ports for mouse and keyboard

• One CLR_CMOS button

• Two eSATA ports

• One 1394a port

• One LAN port

• Six USB ports

• One optical SPDIFO port

• Audio jacks for microphone, line-in and 8-ch line-out

The firmware can also be used to set parameters for different processor clock

speeds.

• Power management

• Wake-up alarms

• CPU parameters

• CPU and memory timing

• ECS M.I.B. BIOS

BIOS Firmware

This motherboard uses AMI BIOS that enables users to configure many system

features including the following:

1. Some hardware specifications and software items are subject to change

without prior notice.

2. Due to chipset limitation, we recommend that motherboard be oper-

ated in the ambiance between 0 and 50 °C.

• Compliant with single chip host controller for IEEE Std 1394-1995 and

IEEE 1394a-2000

• Integrated 400 Mb/s 2-Port PHY for the PCI BUS

• 3.3V Power supply with 5V Tolerant Inputs

1394a Fire Wire

4

Introducing the Motherboard

• Intel X58 & ICH10R

• North Bridge: Intel X58

• South Bridge: Intel ICH10R

• LGA1366 socket for latest Intel

®

Core

TM

i7 processor

• Intel

®

QuickPath Interconnect (Intel

®

QPI) of 4.8 GT/s to 6.4

GT/s supporting different routing lengths

• Triple-channel DDR3 memory architecture

• 6 x 240-pin DDR3 DIMM sockets support up to 24 GB

• Supports DDR3 1333/1066/800 DDR3 SDRAM

• 2 x PCI Express Gen2 x16 slots

• 2 x PCI Express x1 slots

• 1 x PCI Express x4 slot

• 1 x PCI slot

• Supported by Intel ICH10R

• 6 x Serial ATA 3.0 Gb/s Host Controllers

• Supports RAID 0, 1, 5 and 10

• Support by JMicron

®

JMB362

• 2 x eSATA 3.0 Gb/s devices

• Realtek ALC 888S supports 7.1 channel HD audio

• Realtek 8111C PCIE GigaLAN Controller

• 1 x PS/2 keyboard & PS/2 mouse connector

• 1 x CLR_CMOS button

• 2 x eSATA ports

• 1 x 1394a port

• 6 x USB ports

• 1 x RJ45 LAN connector

• 1 x Audio port (1 Line in, 4 x Line out, 1 Optical SPDIF Out)

• 1 x 24-pin ATX Power Supply connector, 8-pin 12V connec-

tor & ATX4P connector

• 6 x Serial ATA connectors

• 3 x USB 2.0 headers support additional 6 USB ports

• 1 x Clear CMOS header

• 1 x Front panel header

• 1 x PWR & RST button

• 1 x Front panel 1394a header

• 1 x COM header

• 1 x SPDIF out header

• 1 x Front panel audio header

• 1 x CD_in header

• CPU_FAN/SYS_FAN/PWR_FAN/NB_FAN connectors

Chipset

Memory

Expansion

Slots

Storage

Audio

Giga LAN

Rear Panel I/O

Internal I/O

Connectors &

Headers

• AMI BIOS with 16Mb SPI ROM

• Supports Plug and Play 1.0A, APM 1.2, Multi Boot, DMI

• Supports ACPI revision 1.0 specification

System BIOS

Form Factor • ATX Size, 305mm x 244mm

CPU

Specifications

5

Introducing the Motherboard

Motherboard Components

Table of Motherboard Components

This concludes Chapter 1. The next chapter explains how to install the motherboard.

LABEL COMPONENTS

1. CPU Socket

LGA1366 socket for Intel

®

Core

TM

i7

p

rocessor

2. CPU_FAN CPU cooling fan connector

3. DDR3_1~6

240-pin DDR3 SDRAM slots

4. ATX_POWER

Standard 24-pin ATX power connector

5. PWR_BTN

Power on button

6. RST_BTN

Reset button

7. SATA1~6

Serial ATA connectors

8. SYS_FAN

System cooling fan connector

9. F_PANEL

Front panel switch/LED header

10. CLR_CMOS

Clear CMOS jumper

11. F_USB1~3

Front panel USB headers

12. F_1394A Onboard 1394a header

13. COM Onboard serial port header

14. PWR_FAN

Power cooling fan connector

15. SPDIFO

SPDIF out header

16. F_AUDIO

Front panel audio header

17. CD_IN

Analog audio input connector

18. PCIE1~2

PCI Express x1 slots

19. PCIEX16_1

PCIEX16_2

20. PCI

32-bit add-on card slot

21. PCIE4X1 PCI Express x4 slot

22. ATX4P Auxiliary power connector for graphics card

23. NB_FAN Northbridge cooling fan connector

24. ATX12V 8-pin +12V power connector

PCI Express slots for graphics interface

6

Introducing the Motherboard

Memo

7

Installing the Motherboard

Chapter 2

Installing the Motherboard

Safety Precautions

• Follow these safety precautions when installing the motherboard

• Wear a grounding strap attached to a grounded device to avoid dam-

age from static electricity

• Discharge static electricity by touching the metal case of a safely

grounded object before working on the motherboard

• Leave components in the static-proof bags they came in

• Hold all circuit boards by the edges. Do not bend circuit boards

Choosing a Computer Case

There are many types of computer cases on the market. The motherboard complies

with the specifications for the ATX system case. Some features on the motherboard

are implemented by cabling connectors on the motherboard to indicators and switches

on the system case. Make sure that your case supports all the features required.

Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O

template in the case matches the I/O ports installed on the rear edge of the

motherboard.

This motherboard carries an ATX form factor of 305 x 244 mm. Choose a case that

accommodates this form factor.

Installing the Motherboard in a Case

Refer to the following illustration and instructions for installing the motherboard in

a case.

Most system cases have mounting brackets installed in the case, which correspond

the holes in the motherboard. Place the motherboard over the mounting brackets

and secure the motherboard onto the mounting brackets with screws.

Ensure that your case has an I/O template that supports the I/O ports and expansion

slots on your motherboard.

8

Installing the Motherboard

Checking Jumper Settings

This section explains how to set jumpers for correct configuration of the motherboard.

Setting Jumpers

Use the motherboard jumpers to set system configuration options. Jumpers with

more than one pin are numbered. When setting the jumpers, ensure that the jumper

caps are placed on the correct pins.

The illustrations show a 2-pin jumper. When

the jumper cap is placed on both pins, the

jumper is SHORT. If you remove the jumper

cap, or place the jumper cap on just one pin,

the jumper is OPEN.

This illustration shows a 3-pin jumper. Pins

1 and 2 are SHORT.

SHORT OPEN

Do not over-tighten the screws as this can stress the motherboard.

9

Installing the Motherboard

Checking Jumper Settings

The following illustration shows the location of the motherboard jumpers. Pin 1 is

labeled.

Jumper Settings

Jumper

Type

Description Setting (default)

CLR_CMOS

3-pin

Clear CMOS

1-2: NORMAL

2-3: CLEAR CMOS

Before clearing the

CMOS, make sure to

turn off the system.

1

CLR_CMOS

To avoid the system unstability after clearing CMOS, we recommend users

to enter the main BIOS setting page to “Load Default Settings” and then

“Save and Exit Setup”.

10

Installing the Motherboard

Installing Hardware

Installing the Processor

Caution: When installing a CPU heatsink and cooling fan make sure that

you DO NOT scratch the motherboard or any of the surface-mount resis-

tors with the clip of the cooling fan. If the clip of the cooling fan scrapes

across the motherboard, you may cause serious damage to the motherboard

or its components.

On most motherboards, there are small surface-mount resistors near the

processor socket, which may be damaged if the cooling fan is carelessly

installed.

Avoid using cooling fans with sharp edges on the fan casing and the clips.

Also, install the cooling fan in a well-lit work area so that you can clearly

see the motherboard and processor socket.

Before installing the Processor

This motherboard automatically determines the CPU clock frequency and system bus

frequency for the processor. You may be able to change the settings in the system

Setup Utility. We strongly recommend that you do not over-clock processors or

other components to run faster than their rated speed.

This motherboard has an LGA1366 socket. When choosing a processor, consider the

performance requirements of the system. Performance is based on the processor

design, the clock speed and system bus frequency of the processor, and the quantity

of internal cache memory and external cache memory.

Warning:

1. Over-clocking components can adversely affect the reliability of the

system and introduce errors into your system. Over-clocking can perma-

nently damage the motherboard by generating excess heat in components

that are run beyond the rated limits.

2. Always remove the AC power by unplugging the power cord from the

power outlet before installing or removing the motherboard or other

hardware components.

Fail-Safe Procedures for Over-clocking

When end-users encounter failure after attempting over-clocking, please take the

following steps to recover from it.

1. Shut down the computer.

2. Press and hold the “Page Up Key (PgUp)” of the keyboard, and then boot the PC

up.

3. Two seconds after the PC boots up, release the “Page Up Key (PgUp)”.

4. The BIOS returns to the default setting by itself.

11

Installing the Motherboard

A. Opening of the Load Plate

· Put your thumb on the tail of the load

plate and press the tail down.

· Rotate the load plate to fully open

position.

B. Disengaging of the Load Lever

· Hold the hook of lever and pull it to the

left side to clear retention tab.

· Rotate the load lever to fully open

position.

C. Removing the Cap

· Be careful not to touch the contact at

any time.

D. Inserting the Package

· Grasp the package. Ensure to grasp on

the edge of the substrate.

· Make sure pin 1 indicator is on your

bottom-left side.

· Aim at the socket and place the package

carefully into the socket by purely

vertical motion.

E. Closing the Load Plate

· Rotate the load plate onto the package

IHS (Intergraded Heat Spreader).

· Engage the load lever while pressing

down lightly onto the load plate.

· Secure the load lever with the hook

under retention tab.

F. Fasten the cooling fan supporting base

onto the CPU socket on the motherboard.

G. Make sure the CPU fan is plugged to the

CPU fan connector. Please refer to the

CPU cooling fan user’s manual for more

detail installation procedure.

CPU Installation Procedure

The following illustration shows CPU installation components.

12

Installing the Motherboard

Installing Memory Modules

This motherboard accommodates four memory modules. It can support six 240-pin

DDR3 1333/1066/800. The total memory capacity is 24 GB.

You must install at least one module in any of the six slots. Each module can be

installed with 4 GB of memory; total memory capacity is 24 GB.

DDR3 SDRAM memory module table

Memory module Memory Bus

DDR3 800 400 MHz

DDR3 1066 533 MHz

DDR3 1333 667 MHz

ff

Channel A: DDR3_1, DDR3_2

ff

Channel B: DDR3_3, DDR3_4

The six DDR3 memory sockets (DDR3_1, DDR3_2, DDR3_3, DDR3_4, DDR3_5,

DDR3_6) are divided into three channels and each channel has two memory sockets

as following:

ff

Channel C: DDR3_5, DDR3_6

1. To achieve better airflow rates and heat dissipation, we suggest that

you use a high quality fan with 3800 rpm at least. CPU fan and

heatsink installation procedures may vary with the type of CPU fan/

heatsink supplied. The form and size of fan/heatsink may also vary.

2. DO NOT remove the CPU cap from the socket before installing a

CPU.

3. Return Material Authorization (RMA) requests will be accepted

only if the motherboard comes with the cap on the LGA1366 socket.

Due to Intel CPU spec definition, the system will not boot if only one

DIMM is installed in DDR3_1, DDR3_3, or DDR3_5. Follow the table

above for recommended memory configuration.

DDR3_1 DDR3_2 DDR3_3 DDR3_4 DDR3_5 DDR3_6

2 DIMMs - Populated - Populated - -

3 DIMMs - Populated - Populated - Populated

4 DIMMs Populated Populated - Populated - Populated

6 DIMMs Populated Populated Populated Populated Populated Populated

Mode

Sockets

Recommend memory configuration

13

Installing the Motherboard

Do not remove any memory module from its antistatic packaging

until you are ready to install it on the motherboard. Handle the

modules only by their edges. Do not touch the components or metal

parts. Always wear a grounding strap when you handle the modules.

Installation Procedure

Refer to the following to install the memory modules.

1 This motherboard supports unbuffered DDR3 SDRAM .

2 Push the latches on each side of the DIMM slot down.

3 Align the memory module with the slot. The DIMM slots are keyed with

notches and the DIMMs are keyed with cutouts so that they can only be

installed correctly.

4 Check that the cutouts on the DIMM module edge connector match the

notches in the DIMM slot.

5 Install the DIMM module into the slot and press it firmly down until it

seats correctly. The slot latches are levered upwards and latch on to

the edges of the DIMM.

6 Install any remaining DIMM modules.

1. For best performance and compatibility, we recommend that users

give priority to the yellow DIMMs (DDR3_2/DDR3_4/DDR3_6) when

installing DIMMs.

2. We suggest users not mix memory type. It is recommended to use

the same brand and type memory on this motherboard.

14

Installing the Motherboard

Table A: DDR3 (memory module) QVL (Qualified Vendor List)

The following DDR3 1333/1066/800 memory modules have been tested and qualified

for use with this motherboard.

Type

Size Vendor Module Name

DDR3 800

1 GB

HYNIX PC3-6400U-6-00

A-data M3OSS3H3I3120B5Z/Boxed

Aeneon AEH760UD00-10FA98X

Corsair CM3X1024-1066C7/Boxed

Hynix HMT112U6AFP8C-G7N0 AA

Kingston

KVR1066D3N7/1G

Micron MT8JTF12864AY-1G1D1

IMSH1GU03A1F1C-10F B2S81427023

IMSH1GU03A1F1C-10G B2S81427034

Gold Bar M378B2873DZ1-CF8 0818

M378B2873DZ1-CF8 0842

Elixir

M2F2G64CB8HA 4N- BE

HMT125U6AFP8C-G7N0 AA

HYMT125U64ZNF8-G8 AA

Kingston

KVR1066D3N7/2G 1.5V 9905403-

006.A00LF

Mic ron

MT16JTF25664AY-1G1D1

IMSH2GU13A1F1C-10F B3S81427044

IMSH2GU13A1F1C-10G B3S81528005

IMSH2GU13A1F1C-13H B3S81124001

Samsung

M378B5673DZ1-CF8 0842

4 GB

Samsung M378B5273BH1-CF8 0840

Aeneon

AXH760UD00-13GA 98X

Corsair CM3X1024-1333C9DHX/Boxed

Hynix HMT112U6AFP8C-H9N0 AA

Kingston

KVR1333D3N9

Qimonda IMSH1GU13A1F1C-13H

Samsung

M378B2873DZ1-CH9

A-DATA

M3OSS6H3J4130E1C5Z

Hexon

ELPH8A UDR- 1 3M8 8

Hynix

HMT125U6AFP8C-H9N0 AA

Kingston KVR1333D3N9K2/2G

Qimonda IMSH2GU13A1F1C-13H B3S81124001

Samsung M378B5673DZ1-CH9 0842

DDR3 1600 1 GB

Kingston KHX12800D3K3/3GX

Hynix

2 GB

DDR3 1066

Qimonda

Samsung

DDR3 1333

2 GB

1 GB

Page is loading ...

ECS X58B-A3 SLI User manual

This manual is also suitable for

ECS X58B-A3 SLI User manual

Related papers

Other documents