Briggs & Stratton 01917-0 Owner's manual

Page is loading ...

Brig, s & Stratton Power Products Automatic Transfer Switch

Installation and Owner's Manual

TABLE OF CONTENTS

TABLE OF CONTENTS ........................... 2

SAFETY RULES .................................. 3

INTRODUCTION ................................ 4

For the Home or Business Owner: .............. 4

For the Installing Dealer/Contractor: ............. 4

Owner Orientation ........................... 4

Installer Responsibilities ........................ 4

Equipment Description ......................... 5

INSTALLATION .................................. 5

Unpacking ................................... 5

Delivery Inspection ........................ 5

Shipment Contents ........................ 5

Mounting Dimensions ...................... 5

ESSENTIAL CIRCUIT ISOLATION .................. 6

Mounting Instructions ......................... 7

Power Wiring Interconnections ................ 7-8

SYSTEM OPERATION ............................. 9

TESTING THE AUTOMATIC TRANSFER SWITCH .... 9

Automatic Sequence ........................... 9

Utility Fail................................ 9

Engine Warm-Up .......................... 9

Transfer ................................. 9

Utility Pickup ............................. 9

Retransfer ............................... 9

Engine Cool Down ........................ 9

Specifications ................................. 9

Model 01917 ............................. 9

Model 01918 ............................. 9

When CallingThe Factory ...................... 9

TROUBLESHOOTING ........................... II

DIAGRAMS, EXPLODEDVIEWS, PARTS LISTS ..... 12-15

NOTES .................................. I0 & 16

WARRANTY ................................... 17

1:7;1_-_:_Je_.'l Bri_s & Stratton Power Products Automatic Transfer Switch

Installation and Owner's Manual

SAFETY RULES

This is the safety alert symbol. It is used to

alert you to potential personal injury

hazards. Obey all safety messages that follow

this symbol to avoid possible injury or death.

The safety alert symbol (_) is used with a signal word

(DANGER, CAUTION,WARNING), a pictorial and/or a

safety message to alert you to hazards. DANGER indicates

a hazard which, if not avoided, will result in death or

serious injury. WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, might

result in minor or moderate injury. CAUTION, when

used without the alert symbol, indicates a situation that

could result in equipment damage. Follow safety messages

to avoid or reduce the risk of injury or death.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard.The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that it

is safe for you and others.You must also make sure that the

procedure, work method or operating technique that you

choose does not render the transfer switch unsafe.

WARNING

Only qualified electricians should attempt installation

of this system, which must strictly comply with

applicable codes, standards and regulations.

WARN ING

DO NOT touch bare wires or receptacles.

DO NOT use transfer switch with worn, frayed, bare or

otherwise damaged wiring.

DO NOT handle electrical cords while standing in water,

while barefoot, or while hands or feet are wet.

If you must work around a unit while it is operating, stand on

an insulated dry surface to reduce shock hazard.

DO NOT allow unqualified persons or children to operate or

service transfer switch.

In case of an accident caused by electrical shock, immediately

shut down the source of electrical power and contact the

local authorities. Avoid direct contact with the victim.

CAUTION

Use transfer switch only for intended uses.

If you have questions about intended use, ask dealer or

contact Briggs and Stratton Power Products.

DO NOT expose transfer switch to excessive moisture, dust,

dirt, or corrosive vapors.

Despite the safe design of the transfer switch, operating this

equipment imprudently, neglecting its maintenance or being

careless can cause possible injury or death.

Remain alert at all times while working on this equipment.

NEVER work on the equipment when you are physically or

mentally fatigued.

If connected devices overheat, turn them off and turn off their

circuit breaker/fuse.

Bri_s & Stratton Power Products Automatic Transfer Switch

Installation and Owner's Manual

INTRODUCTION

Thank you for your purchase of this Briggs & Stratton

Power Products Automatic Transfer Switch.This product is

intended for use with Briggs & Stratton Home Standby

Generator sets ONLY.This is an optional home standby

system which provides an alternate source of electric

power and to serve loads such as heating, refrigeration

systems, and communication systems that, when stopped

during any power outage, could cause discomfort, or the

like.This product DOES NOT qualify for emergency

standby as defined by NFPA 70 (NEC).

Briggs and Stratton Power Products (BSPP) has made every

effort to provide for a safe, streamlined and cost-effective

installation. Each installation is unique; it is impossible for

BSPPto know and advise of all conceivable procedures and

methods by which installation might be performed, nor the

potential hazards associated with those methods. For these

reasons,

Only licensed electrical contractors should

install transfer switches. Installations must

strictly comply with all applicable federal,

state and local codes, standards and

regulations.

Your BSPPTransfer Switch is supplied with this combined

"Installation and Owner's Manuar'.This is an important

document and should be retained by the owner after the

installation has been completed.

Every effort has been expended to make sure that the

information in this manual is both accurate and current.

However, the manufacturer reserves the right to change,

alter or otherwise improve the system at any time without

prior notice.

For the Home or Business Owner

To help you make informed choices and communicate

effectively with your installation contractor(s),

Read and understand the

Owner Orientation Section of this manual

BEFORE contracting or starting

your transfer switch installation.

To arrange for proper installation, contact the store at

which you purchased your BSPPTransfer Switch, your

dealer, or your utility power provider.

The Transfer Switch Warranty is VOID

unless the system is installed by a

licensed electrical professional.

For the Installing Dealer/Contractor

Check federal, state and local codes for questions on

installation.

If you need more information about the transfer switch,

call 1-800-743-4115,between 8:00AM and 5:00 PM CT.

Owner Orientation

The illustrations are for typical circumstances and are

meant to familiarize you with the installation options

available with your transfer switch.

Local codes, appearance, and distances are the factors that

must be considered when negotiating with an installation

professional.As the distance from the existing electrical

service increases, compensation in wiring materials must be

allowed for.This is necessary to comply with local codes

and overcome electrical voltage drops.

The factors mentioned above will have a direct effect

on the overall price of your transfer switch installation.

NOTE: Your installer must check local codes AND obtain

permits before installing the system.

• Read and follow the instructions given in this manual.

• Follow a regular schedule in caring for and using your

transfer switch, as specified in the manual.

Installer Responsibilities

• Read and observe the safety rules.

• Read and follow the instructions given in this manual.

• Check federal, state and local codes.

1_ I Briggs&StrattonPowerProductsAutomaticTransferSwitch

Installation and Owner's Manual

Equipment Description

These new generation transfer switches are intended to

operate compatible electrical loads of normal residential

installations.The load is connected either to utility power

(normal) or home standby power (emergency).The transfer

switch monitors utility and generator voltages and will

automatically connect to the appropriate source of power.

Major components of the transfer switch are 2 pole

contactor switches, control circuit board, fused utility

terminals and interconnecting wiring.

The transfer switch is coil-operated from utility or

generator inputs and contains suitable electrical interlock

switches to eliminate the possibility of connecting the

utility service to the generator output. It has ratings

capable of switching generator power into the residence.

The control module circuit board has active circuits sensing

utility and generator voltages. It creates a signal for the

generator start-up, switch transfer, retransfer when utility is

restored and generator cool down periods.The control

board also contains red and green lights indicating the power

sources available.

INSTALLATION

Unpacking

Delivery Inspection

After removing the carton, carefully inspect the transfer

switch components for any damage that may have occurred

during shipment.

IMPORTANT: If loss or damage is noted at time of

delivery, have the person(s) making delivery note all damage

on the freight bill and affix his signature under the

consignor's memo of loss or damage. If loss or damage is

noted after delivery, contact the carrier for claim

procedures. Freight damaged parts are not warranted.

Shipment Contents

• Automatic Power Transfer Switch

• Installation and Owner's Manual

Mounting Dimensions

Figure I depicts the physical size and mounting hole

locations of the automatic transfer switch enclosure.The

enclosure for model 01917 is suitable for indoor use ONLY.

The enclosure for model 01918 issuitable for

indoor/outdoor use.

®

Enclosure Dimensions Mounting Dimensions

Model 01917

Enclosure Dimensions Mounting Dimensions

Model 01918

The transfer switch enclosure is commonly secured

through the predrilled holes, as shown.

Bri_s&StrattonPowerProductsAutomaticTransferSwitch

Installation and Owner's Manual

ESSENTIAL CIRCUIT

ISOLATION

Essential electrical loads are loads that will be powered by

the Home Generator System. Essential loads are grouped

together and wired into the transfer switch.

TO THE INSTALLER: Consult with Home

Generator System owner(s) to discuss their

"Selection of Essential Circuits", described in the

owner's manual.

Ensure that the total of the selected load circuits fed by this

transfer switch are within the generator's rated capacity.

The following requirements apply to this type of isolation

system:

• The Automatic Transfer Switch is installed after the main

distribution panel.

• The Automatic Transfer Switch has a load rating of

50 Amps.This is the maximum load rating of the essential

loads.

All wiring must conform to national, state and local codes.

The illustration in Figure 2 depicts the Home Generator

System and assumes the utility is supplying 120/240Volt,

single-phase electrical service.

To Utility Power

I........

To Range --'_-----

240V ,__.__ _--

To Water Heater _____

,,

i

.....................

i'--

i

I

To griggs & Stratton 1

Home Generator Unit ,,

120V To Microwave '

120VTo Bathroom

240V To Well Pump ,

120VTo Sump Pump

,_________I Watt Meter

......... ., i Main Distribution Panel

-2"

Neutral

L ..................................

To Air Conditioner (240V)

To Other Circuits (120V)

Automatic Transfer Switch

(in normal position)

120VTo Freezer

To Refrigerator }

To Lights

To Furnace Blower

120V

l_ I Brig, s & Stratton Power Products Automatic Transfer Switch

Installation and Owner's Manual

Mounting Guidelines

The Model 01917 Automatic Transfer Switch is enclosed in

a NEMAType I enclosure suitable for indoor use only.

The Model 01918 Automatic Transfer Switch is enclosed in

a NEMAType 3R enclosure suitable for indoor/outdoor

use.

Guidelines for mounting the Automatic Transfer Switch

include:

• Model 01918 Automatic Transfer Switch must be installed

with minimum NEMA 3R hardware for conduit

connections.

• Install the switch on a firm, sturdy supporting structure.

• To prevent switch contact distortion, level and plumb the

enclosure.This can be done by placing washers between I.

the switch enclosure and the mounting surface.

• NEVER install the switch where any corrosive substance

might drip onto the enclosure.

• Protect the switch at all times against excessive moisture,

dust, dirt, lint, construction grit and corrosive vapors. 2.

The typical installation of the Automatic Power Transfer

Switch is depicted in Figure 3. Discuss layout 3.

suggestions/changes with the owner before beginning the

system installation process. 4.

Main

Distribution

Panel

Automatic

Transfer Switch

Power Wiring Interconnections

All wiring must be the proper size, properly supported, of

approved insulation qualities, and protected by NEC

approved conduit.

Complete the following connections between the

generator, transfer switch and main distribution panel

(Figure 4, on next page).

CAUTION

.

6.

7.

8.

Failure to follow above warning could cause damage and/or

malfunction of equipment.

Connect utility power supply leads from a two pole

breaker installed in the main distribution panel to

transfer switch terminals marked "UTILITY

CONNECTION". Use a 50 Amp circuit breaker.

Ensure breaker is turned OFF.

Connect main distribution panel ground to the transfer

switch "GND" bus.

Connect main distribution panel neutral lead to

transfer switch "NEUTRAL" terminal.

Connect generator power supply leads from the

generator's control panel to transfer switch terminals

marked "GENERATOR CONNECTION".

Connect generator Neutral from the control panel to

the transfer switch "NEUTRAL" terminal.

Connect generator"GND" from the control panel to

the transfer switch "GND" terminal.

Connect generator utility 240V terminals to transfer

switch utility 240V terminals.

Tighten all wire connections/fasteners to proper

torque.

Bri_s&StrattonPowerProductsAutomaticTransferSwitch 1_1

Installation and Owner's Manual

Main

Distribution

Panel

Neutral Ground

Bus Bus

Utility

[_ [_ Connection

/

Two Pole

Breaker

Automatic Power Transfer Switch

Neutral

Bus

Home Standby

System

Generator

Neutral is

White wire

Generator

Connection

/

Wire i

J

Rearof

Control

Panel

Utility 240V AC

Brig,s&StrattonPowerProductsAutomaticTransferSwitch

Installation and Owner's Manual

SYSTEM OPERATION

To select automatic transfer operation, do the following:

I. Set circuit breaker that sends utility power to transfer

switch to "On" position.

2. Set generator's main circuit breaker to its "On"

position.

3. Install 15Amp fuse in control panel on generator.

4. Set AUTO/OFF/MANUAL switch on generator to

"AUTO" position.

The system will now be in automatic operation mode.

TESTING THE

AUTOMATIC TRANSFER

SWITCH

Turn the circuit breaker feeding the transfer switch, to the

"Off' position.The automatic sequence will follow.To go

back to utility power, turn the circuit breaker to the "On"

position.

Automatic Sequence

Utility Fail

Utility voltage sensor senseswhen utility voltage isbelow

70 percent of nominal. Enginestart sequence isinitiated

after 6 second time delay.

Engine Warm-Up

Time delay to allow for engine warm-up before transfer

fixed at 20 seconds or 50 seconds with optional cold

weather package.

Transfer

Transfers from utility to standby supply occurs after

standby voltage isabove set levels. Minimum engine run

time is 4 minutes after transfer.

Utility Pickup

Voltagepickup level is80 percent of nominal voltage.

Retransfer

Retransfer from standby to utility supply 10 seconds after

utility voltage supply is above pickup level.

Engine Cool Down

Engine will run for 60 seconds after retransfer.

Specifications

UL® 1008 Listed Transfer Switch

Model 01917

Enclosure ................... NEMA I

Maximum Load/Circuit:

from Load Center .......... 50 Amps

RatedAC Voltage ............. 250Volts

Poles ...................... 2

Frequency .................. 50/60 Hz

Fault Current Rating .......... 5,000 RMS Symmetrical

Amperes

Weight ..................... 27 Ibs.

Model 01918

Enclosure................... NEMA 3R

Maximum Load/Circuit:

from Load Center .......... 50 Amps

RatedAC Voltage ............. 250Volts

Poles ...................... 2

Frequency .................. 50/60 Hz

Fault Current Rating .......... 5,000 RMS Symmetrical

Amperes

Weight ..................... 34 Ibs.

When Calling the Factory

Before contacting Briggs and Stratton Power Products

regarding service or repair of this transfer switch, obtain

the Model Number and Serial Number from the unit data

decal located on or inside the case.

To contact Briggsand Stratton Power Products call

1-800-743-4115,between 8:00AM and 5:00 PM CT.

Brig, s & Stratton Power Products Automatic Transfer Switch

Installation and Owner's Manual

NOTES

10

Brig,s&StrattonPowerProductsAutomaticTransferSwitch

Installation and Owner's Manual

TROUBLESHOOTING

Problem Cause

Automatic transfer switch does I.

not transfer to generator 2.

I.

Automatic transfer switch does

not transfer to utility .

Generator breaker open.

Generator voltage not acceptable.

Maindistribution panel breaker

open.

Utility voltage not acceptable.

Generator is still running after Engine cool down period.

switch transfers to utility power

I.

Generator is still running after

utility power is restored

I. Minimum engine run time hasnot

elapsed.

2. Fuse(s) in transfer switch is

defective.

Correction

I. Reset generator circuit breaker.

2. Refer to generator manual.

I. Reset main distribution panel

breaker.

2. Wait for utility voltage to return to

normal.

Engine will stop after I minute.

.

Wait five minutes for transfer

switch to retransfer to utility

power.

Check fuse(s) and replace if

necessary.

II

Brig,s&StrattonPowerProductsAutomaticTransferSwitch

Installation and Owner's Manual

TRANSFER SWITCH SCHEMATIC

SCHEMATIC

MAIN

DISTRIBUTION

PANEL

NI o

UTILITY

SUPPLY

240 VAC

[ N

I j

i,I O / O

I

E

D OE1

GENERATOR

SUPPLY

240 VAC

U [J U

J5 J4 J3

206

U

J7

205

U U [J

J6 J1 J2

CONTROL BOAR]]

12

Brig,s & Stratton Power Products Automatic Transfer Switch

Installation and Owner's Manual

TRANSFER SWITCH WIRING DIAGRAM

WIRE DIAGRAM

206

NI

128

LI LJ

J7 J6 J5

N2

I

CONTRBL BOARD

-NII UTILITY

___ RELAY

E2

N1

El

N1

556 --

205

127

GENERATBR

@

-_ RELAY

E1

@

UTILITY

240VAC

@

13

Brig, s & Stratton Power Products Automatic Transfer Switch

Installation and Owner's Manual

I

2J_

_P3

TRANSFER SWITCH EXPLODEDVIEW & PARTS LIST

MODEL 01917

NEMA I

Item Part #

I 189872GS

2 192909GS

3 192151GS

4 190984GS

5 192597GS

6 193626GS

7 B4854GS

8 189916GS

9 194205GS

10 185891GS

II 193239GS

17

ii

8

7

Description

LOADCENTER 12

BOARD, Control 13

HOLDER, Fuse 14

DECAL, Fuse 15

DECAL, Utility, 240V AC 16

SCREW 17

TERMINAL, SLS 18

BAR, BUS, Copper 19

SCREW 20

RELAY, 50A 2 I

SCREW 22

Item Part #

B4857GS

90983GS

90982GS

92701GS

90992GS

92707GS

92708GS

90850GS

B5106GS

B5107GS

192709GS

Description

FUSE,2A

DECAL, Torque

DECAL, Lug

SPACER

DECAL, Warning

DECAL, 50A, ATS

DECAL, Identification

DECAL, ATS, BSPP

DECAL, Utility Connection

DECAL, Gen. Connection

DECAL, UL Listed

14

I

2J_

_P3

Briggs & Stratton Power Products Automatic Transfer Switch

Installation and Owner's Manual

TRANSFER SWITCH EXPLODEDVIEW & PARTS LIST

MODEL 0 19 18

NEMA 3R

18

Item Part #

I 191207GS

2 192909GS

3 192151GS

4 190984GS

5 192597GS

6 193626GS

7 B4854GS

8 189916GS

9 194205GS

10 185891GS

II 193239GS

7_

9

\

7

8 7

7

\ 17

Description

LOADCENTER

CONTROL BOARD

HOLDER, Fuse

DECAL, Fuse

DECAL, Utility, 240V AC

SCREW

TERMINAL, SLS

BAR, BUS,Copper

SCREW

RELAY,50A

SCREW

Item Part #

12 B4857GS

13 90983GS

14 90982GS

15 92701GS

16 90992GS

17 92713GS

18 92714GS

19 90850GS

20 B5106GS

21 B5107GS

22 192715GS

Description

FUSE,2A

DECAL, Torque

DECAL, Lug

SPACER

DECAL, Warning

DECAL, 50A, ATS

DECAL, Identification

DECAL, ATS, BSPP

DECAL, Utility Connection

DECAL, Gen. Connection

DECAL, UL Listed

15

Brig,s&StrattonPowerProductsAutomaticTransferSwitch

Installation and Owner's Manual

NOTES

16

Effective January 1, 2003 replaces all undated Warranties and all Warranties dated before January 1, 2003

!!iil

Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s), of the equipment that is defective in material

or workmanship or both. Transportation charges on parts submitted for repair or replacement under this warranty must be borne by

purchaser. This warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest

Authorized Service Dealer in our dealer Iocator map at www.briggspowerproducts.com.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY

AND ALL IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED

TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty

lasts, and some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation

and exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state

to state or country to country.

Consumer Use

Commercial Use

The engine and starting batteries are warranted solely by the manufacturers of those products.

2 years for all consumer products in the European Union. Parts only on 2nd year for consumer use of Portable Generator and

Home Generator System - Less than 10 KW, outside of European Union.

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time

stated in the table above. "Consumer use" means personal residential household use by a retail consumer. "Commercial use" means all other

uses, including use for commercial, income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter

be considered as commercial use for purposes of this warranty. Equipment used for Prime Power in place of utility are not applicable to

this warranty. Electric Powered Pressure Washers used for commercial purposes are not warranted.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR

PROOF OF PURCHASE RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY

SERVICE IS REQUESTED, THE MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY

PERIOD.

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most

warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not

apply if equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation.

Similarly, the warranty is void if the manufacturing date or the serial number on the equipment has been removed or the equipment has been altered

or modified. During the warranty period, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to

be defective under normal use and service. This warranty will not cover the following repairs and equipment:

• Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty does not

cover repair when normal use has exhausted the life of a part or the equipment.

Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized

installation or alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper maintenance, repair or storage so as,

in our judgment, to adversely affect its performance and reliability. This warranty also does not cover normal maintenance such as adjustments,

fuel system cleaning and obstruction (due to chemical, dirt, carbon, lime, etc.).

Other Exclusions: This warranty excludes wear items such as quick couplers, oil gauges, belts, o-rings, filters, pump packing, etc., pumps that

have been run without water supplied or damage or malfunctions resulting from accidents, abuse, modifications, alterations, or improper servicing

or freezing or chemical deterioration. Accessory parts such as guns, hoses, wands and nozzles are excluded from the product warranty. Also

excluded is used, reconditioned, and demonstration equipment; equipment used for prime power in place of utility power and equipment used in

life support applications.

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WI, USA

Page is loading ...

Conectadorautom_ticodeBrig,s&StrattonPowerProducts

Manual de Instalacibn y del Propietario

REMARQUES

26

Page is loading ...

Conectadorautom_ticodeBrig,s&StrattonPowerProducts

Manual de Instalacibn y del Propietario

NOTAS

38

Page is loading ...

Briggs & Stratton 01917-0 Owner's manual

This manual is also suitable for

Briggs & Stratton 01917-0 Owner's manual

in other languages

Related papers

Other documents