GEAppliances.com
0
0_
0_
Safety Instructions ............. 2,3
Operating Instructions
Controls ........................... 4-6
Care and Cleaning
Air Filter .............................. 6
Outdoor Coils ......................... 6
Installation Instructions ...... 7-1o
Troubleshooting Tips ............ 11
Normal Operating Sounds ............ 11
Consumer Support
Consumer Support .......... Back Cover
Ownership Registration for
Customers in Canada only ........ 13, 14
Warranty for Customers
in Canada ........................... 16
Warranty for Customers
in the U.SA ........................... 15
*ENERGY STAR® labeled product
ENERGYSTAR
As an ENERGYSTAR®partner, GEhas
determined that this product meets
the ENERGYSTAR®guidelines for
energy efficiency.
AER05
AEH06*
AEH08*
Climotiseur
Lo section fran_aise commence _ la page 17
Acondicionodor
deoire
Lo secci6n en espahol empieza en la pdgina 33
0_
Write the model and serial numbers here:
Model #
Serial #
Find these numbers on a label on the sideof
the air conditioner.
In Canada, contact us at:
www.GEAppliances.ca
49-7684 12-10 GE
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
Foryour safety, the information in this manual must be followed to minimize the risk of fire, electric
shock or personal injury.
SAFETYPRECAUTIONS
Use this appliance only for its intended
purpose as described in this Owner's
Manual.
This air conditioner must be properly
installed in accordance with the Installation
Instructions before it is used.
Never unplug your air conditioner by pulling
on the power cord. Always grip plug firmly
and pull straight out from the receptacle.
Replace immediately all electric service
cords that have become frayed or otherwise
damaged. A damaged power supply cord
must be replaced with a new power supply
cord obtained from the manufacturer and
not repaired. Do not use a cord that shows
cracks or abrasion damage along its length
or at either the plug or connector end.
Turn the unit OFF and unplug your air
conditioner before cleaning.
GEdoes not support any servicing of the
air conditioner. We strongly recommend
that you do not attempt to service the air
conditioner yourself.
For your safety...do not store or use
combustible materials, gasoline or other
flammable vapors or liquids in the vicinity
of this or any other appliance.
Allair conditioners contain refrigerants,
which under federal law must be removed
prior to product disposal. If you are getting
rid of an old product with refrigerants, check
with the company handling disposal about
what to do.
If the receptacle does not match the plug,
the receptacle must be changed out by u
qualified electrician.
These R410A air conditioning systems
require contractors and technicians to
use tools, equipment and safety standards
approved for use with this refrigerant.
DO NOT use equipment certified for
R22 refrigerant only.
2
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
For personal safety, this appliance must be
properly grounded.
DO NOT use an adapter plug with this appliance.
The power cord of this appliance is equipped
with o 3-prong (grounding) plug which mutes
with u standard 3-prong (grounding) wall outlet
to minimize the possibility of electric
shock hazard from this appliance.
Have the wall outlet and circuit checked by
a qualified electrician to make sure the outlet
is properly grounded.
Where a 2-prong wall outlet is encountered,
it isyour personal responsibility and obligation to
have it replaced with o properly grounded
3-prong wall outlet.
The air conditioner should always be plugged
into its own individual electrical outlet which has
o voltage rating that matches the rating plate.
Power cord includes a current interrupter device.
A test and reset button is provided on the plug
case. The device should be tested on o periodic
basis by first pressing the TESTbutton and
then the RESETbutton while plugged into the
outlet. If the TESTbutton does not trip or if the
RESETbutton will not stay engaged, discontinue
use of the air conditioner and contact o qualified
service technician.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause o fire hazard from overheated wires.
See the Installation Instructions, Electrical
Requirements section for specific electrical
connection requirements.
WARNING!
USEOF EXTENSION CORDS
RISK OF FIRE. Could couse serious injury or
death.
• DO NOT use an extension cord with this
Window Air Conditioner.
• DO NOT use surge protectors or multi-outlet
adaptors with this Window Air Conditioner.
GEAppliances.com
READAND FOLLOWTHISSAFETYINFORMATIONCAREFULLY.
SAVE THESE INSTRUCTIONS
About the controlson theair conditioner.
Features and appearance will vary.
Lights next to the touch pads on the air conditioner control panel indicate the selected settings.
Light indicates the unit
is in the temperature or
Light indicates the unit delay time Set mode.
is in the temperature or
delay time Set mode.
High m Cool
I Ned I Energy Saver
! LOW I Fan Only
_onsomemodels -- _
Light indicates the
1
delay timer is set.
NOTE: The display always shows the
room temperature except when setting
the Set temperature or the Delay timer.
Auto
High m Coot
Pied _ Energy Saver
LOW J Fun Only
Temp/Delay
Light indicates the [
delay timer Jsset. (on some models)
Air Conditioner Controls
Delay 1-24hr
Delay timer @
Decrease
0 Mode select
0
Fan speed 0
Decreose
Temperature 0
set IncFeose
and
Decreose
I
Remote Control
Delay timer
Increase
Auto Fan on
Fan speed
Increase
Unit power
on/off
Controls (onsome models)
Power Pad
Turns air conditioner on and off.When turned
on,the display will show the room temperature.
Display
Showsthe room temperature or time remaining
onthe Delay timer. Showsthe Settemperature
while setting the temperature in Cool orEnergy
Saver modes.The Setlight will turn onwhile
setting.
NOTE:Thedisplay will change to show the room
temperature after settings havebeen made.
O emp Increase •/Decrease • Pads
Useto set temperature when in Coolor Energy
Saver mode. TheSetlight will turn onwhile
setting.
Delay Timer Increase • (4-1/Decrease • (-)
Pads
Eachtouch of the Increase •/Decrease •
pads on the unit or the Increase +/Decrease -
pads on the remote control willset the delay
time when using the Delay 2-24hr timer. The
Set light willturn on while setting.
O an Speed Pads
Useto set the fan speedto Low, Med, High
or Auto on the unit. NOTE:On the remote
control, use the fan speed Increase + /
Decrease - pads to set the fan speeds to Low,
Med or High. Use the Auto pad to turn Auto
fanon.
0
0
Mode Pad
Useto set the air conditioner to Cool, Energy
Saver or Fan Onlymode.
Delay Pads/Delay 2-24hr Pad
Delay ON--When the air conditioner isoff,it can
be set to automatically come onin 1 to 24 hours
at its previous mode and fan settings.
Delay OFF--Whenthe air conditioner ison,
it can beset to automatically turn offin 1to
24 hours.
How to set:
Pressthe Delay 2-24hr pad on the unit or the
Delay pad on the remote control. Eachtouch
of the Increase • /Decrease • pads onthe
unit or the Increase +/Decrease - pads on
the remote control will set the timer in 1-hour
intervals.TheSet light will turn on while setting.
Toreview the remaining time on the Delay
2-24hr timer, pressthe Delay 2-24hr pad on
the unit or the Delay pad on the remote control.
Usethe Increase •/Decrease • pads on the
unit or the Increase +/Decrease - pads on the
remote control to set a new time ifdesired.
To cancel the timer, press the Delay 1-24hr pad
until the light on the Delay 1-24hr pad goes off.
4
Note: The default temperature reading on the display is degree Fahrenheit (°F). Tochange the display to
degree Celcius (°C),press the Temp Increase • and Temp Decrease • buttons together and hold for 3
seconds. Repeat the process to change back to degree Fahrenheit (°F)
Features and appearance will vary.
GEAppliances.com
High Low
Cool _ Cool
Low
Fan
O
OFF
MODE
MODE CONTROL
O
Coolest
7
TEMP
2
5
TEM PERATURE CONTROL
Controls (on some models)
0
Mode Control
High Cool and Low Cool provide coolingwith
different fan speeds.
Fansettings provide air circulation and filtering
without cooling.
NOTE:If you move the mode control from a cool
setting to OFFor to a fan setting,wait at least
3 minutes before switching back to a cool
setting.
O TEMP Control
TheTEMPcontrol isusedto maintain the room
temperature. Thecompressor will cycleon
and off to keepthe room at the same levelof
comfort. When you turn the knob to a higher
number, the indoor air will become cooler.Turn
the knob to a lower number and the indoor air
will become warmer.
Cooling Descriptions
For Normal Cooling-Select High Cool or Low
Cool with the TEMPERATUREcontrol at midpoint.
For Maximum Cooling--Select High Cool with
the TEMPERATUREcontrol at the highest number
available on your knob.
For Quieter and Nighttime Cooling-Select Low
Cool with the TEMPERATUREcontrol at midpoint.
About thecontrols ontheair conditioner.
Do Not Operate in Freezing Outdoor
Conditions
Thiscool-only air conditioner was not designed for
freezing outdoor conditions. It must not be used in
freezing outdoor conditions.
Remote Control
Toensure proper operation, aim the remote
control at the signal receiver on the air
conditioner.
Hake sure nothing isbetween the air conditioner
and the remote control that could block the
signal.
Theremote control signal has o range of
up to 20 feet.
Make sure batteries ore fresh and installed
correctly as indicated on the remote control.
Remotecontains o magnet allowing it to attach
to metal surfaces.
6
Cool Mode
Usethe Cool mode ot Low, Med, High orAuto Fan
Speedfor cooling. Usethe Temperature Increase •
/Decrease • podsto set the desired temperature
between 64°Fand 86°Fin Z%increments.
An electronicthermostat isusedto rnointointhe room
temperature. Thecompressorwill cycleon und off
to keepthe room at the set levelof comfort.Setthe
thermostat at o lower number and the indoor air will
become cooler.Setthe thermostat at o highernumber
and the indoor air willbecome wormer.
NOTE:If theair conditioner isoff and isthen turnedon
while setto o Coolsetting or if turnedfrom o fan setting
to o Coolsetting,it may takeapproximately 3 minutes
for thecompressorto start and coolingto begin.
Cooling Descriptions
For Normal Cooling-Select the Cool mode and
High orF/ed fan with o middle set temperature.
For Maximum Cooling--Select the Cool mode
and High fan with o lower set temperature.
For Quieter and Nighttime Cooling-Select the
Coolmode and Low fan with o middle set
temperature.
Energy Saver Mode
Controlsthe fan.
ON--The fan will cycleon and off with the
compressor.This resultsin wider variations of room
temperature and humidity. Normally usedwhen the
room isunoccupied. NOTE:Thefan may continue to
run for o short time after thecompressor cyclesoff.
OFF--Thefan runsoil the time, while the compressor
cycles on and off.
Fan Only Mode
Usethe FanOnly Node at Low, Ned or Highfan
speedto provide air circulation and filtering without
cooling. Sincefan-only settings do not provide
cooling, o Settemperature cannot be entered. The
room temperature will appear
in the display.
NOTE:Auto FanSpeedcannot be usedwhen in the
Fan Only Mode.
Auto Fan Speed
Setto Auto fan speedfor the fan speedto
automatically set to the speed needed to provide
optimum comfort settings with the set temperature.
If the room needsmore cooling, the fan speed
will automatically increase.If the room needs less
cooling, the fan speedwill automatically decrease.
NOTE:Auto FanSpeedcannot be used when in the
Fan Only Mode.
Power Outage Recovery Feature
Inthe case of o power outage or interruption, the
unit will automatically restart in the settings lost
used offer the power isrestored. Ifthe Delay 1-24hr
feature was set,it will resume countdown. You may
need to set o new time if desired.
Additional important information.
Air Direction
Usethe lever to adjust the air direction left and right
only.
GEAppliances.com
Care and cleaning of the air conditioner.
Grille and Case
Turn the air conditioner off and remove the plug from To cleon, use water and a mild detergent. Do not use
the wall outlet before cleaning, bleach or abrasives.
Air Filter
Theair filter behind the front grille should be checked
and cleaned at least every :30daysor more often if
necessary.
Toremove:
Pullthe tab onthe right sideofthe unit untilthe filter
isout.
Toremove:
Openthe inlet grille by pulling downward on the tubs
at the top upper corners of the inletgrille untilthe
grille isin a 450position. Removethe filter.
Cleonthe filter with worm, soapy water. Rinseand let
the filter dry before replacing it. Do not cleon the filter
in a dishwasher.
CAUTION: Noro eratetheair
conditioner without o filterbecause dirt and lint will
clog it and reduce performance.
Tab
Outdoor Coils
The coils on the outdoor side ofthe air conditioner
should be checked regularly. Ifthey are clogged with
dirt or soot, they may be professionally cleaned.
Tab
How to Insert the Batteries in the Remote Control
Removethe battery cover by sliding it according
to the arrow direction.
Insert new batteries, making sure that the (+)
and (-)of battery ore installed correctly.
Reattachthe cover bysliding it back
into position.
NOTES:
Use2 "AAA"(1.5volt) alkaline batteries. Donot
userechargeable batteries.
Removethe batteriesfrom the remote control if
the system isnot going to be usedfor a long time.
Donot mix old and new batteries. Do not mix
alkaline,standard (carbon-zinc)or rechargeable
(ni-cad,ni-mh, etc)batteries.
I
Installation
Instructions
Air Conditioner
I-_ Ouestions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com
In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca I
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
• IMPORTANT - Savetheseinstructions
forlocalinspector'suse
• IMPORTANT - Observeallgoverning
codes and ordinances
• Note to Installer- Be sure to leave these
instructions with the Consumer.
• Note to Consumer - Keep these instructions for
future reference.
• Skill level- Installation of this appliance requires
basic mechanical skills.
• Completion time - Approximately 1 hour
• We recommend that two people install this
product.
• Proper installation is the responsibility of the
installer.
Product failure due to improper installation is not
covered under the Warranty.
You MUST use all supplied ports and use proper
installation procedures as described in these
instructions when installing this air conditioner.
Q ELECTRICAL REQUIREMENTS
(_ ome models require a 115/120-volt AC,
60-Hz grounded outlet protected with a
15-amp time-delay fuse or circuit breaker.
The 3-prong grounding plug minimizes the
possibility of electric shock hazard. If the wall outlet
you plan to use is only o 2-prong outlet, it isyour
responsibility to hove it replaced with o properly
grounded 3-prong wall outlet.
©
Some models require 230/208-volt AC,
protected with a time-delay fuse or circuit
breaker. These models should be installed
on their own single branch circuit for best
performance and to prevent overloading
house or apartment wiring circuits, which
could cause a possible fire hazard from
overheating wires.
CAUTION:
Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
Do not change the plug on the power cord
of this air conditioner.
Aluminum house wiring may present special
problems--consult a qualified electrician.
TOOLS YOU WILL NEED
Phillips head screwdriver
Fiat-blade screwdriver
Pencil Ruler or tope measure
Level Scissors or knife
Power cord includes a current interrupter
device. A test and reset button is provided on the
plug case. The device should be tested on a periodic
basis by first pressing the TESTbutton and then the
RESETbutton while plugged into the outlet. If the
TESTbutton does not trip or
if the RESETbutton will not stay engaged, discontinue
use of the air conditioner and contact o qualified
service technician.
Installation Instructions
PARTS INCLUDED
(Appearance may vary)
Top mo_
Air
conditioner
_e Window
al
FOamgO_
Left
accordion
panel _
Top mo '_
seal strip
Right
accordion
panel
/
Type A (/4) Type B (6)
Window locking
bracket (1)
Instollotion Instructions
[] WINDOW REQUIREMENTS
• Theseinstructions are for a standard double-hung
window. You will need to modify them for other types
of windows.
• The air conditioner can be installed without the
accordion panels if needed to fit in a narrow
window. See the window opening dimensions.
• All supporting parts must be secured
to firm wood, masonry or metal.
• The electrical outlet must be within reach of the
power cord.
• Follow the dimensions in the table and illustration
for your model.
Models A B
AER05 12 1/2" min. 23"-38"
AEH06 13 1/2" min. 22 1/2"-38"
AEH08
! I
[i_=4]
(Withaccordion panels)
t_
I I
I-}'1STORM WINDOW REQUIREMENTS
A storm window frame will not allow the air
conditioner to tilt toward the outside, and will keep it
from draining properly.
To adjust for this, attach a piece of wood to the sill.
WOOD PIECES
WIDTH: 2"
LENGTH:Long enough to fit inside the window
frame.
THICKNESS: To determine the thickness place a
piece of wood on the sill to make it 1/2" higher
than the top of the storm window frame or the vinyl
frame
Attach securely with nails or screws provided by the
installer.
1/2" higher
than storm
window
frame
Storm window
frame
1/2" higher
than vinyl frame
; ; (°n s°me wind°ws),/,, Wood
_-n-i[ ,, #,-Jf l
- r r Vinylframe I I
r31ATTACH THE TOP MOUNTING RAIL
SEAL STRIP
(Some models may have the seal strip already
attached to the top mounting rail. If applicable,
skip this step.)
Remove the backing from the top mounting rail
seal strip and attach the seal strip to the bottom
of the top mounting rail, along the front edge.
Topmountingrail
Remove
backing
from seal
strip
FRONTVIEW Topmountingrail
.,-., . ..... , , . ..'...'....... , ,- . ..
I
Sealstrip
I_1 PREPARE THE AIR CONDITIONER
I_] Install the top mounting rail with 4 Type A
screws from the outside of the case.
Topmounting rail
Bottom mountingrail
r_ Hold the accordion panel in one hand and
gently pull back to free the open end.
10
Installation Instructions
[] PREPARETHE AIR CONDITIONER
(cont.)
r_ Slide the free end of the accordion panel into
the side panel rails. Slide the panel down. Be
sure to leave enough space to slip the top
and bottom of the frame into the rails on the
cabinet.
NOTE: There is a right and a left accordion
panel. Be sure to use the proper panel for each
side.
r_ Slide the left and right accordion panels into
the top and bottom mounting rails.
Top mounting rail Top ight
Top left
Bottom mounting rail
I-sl PREPARE THE WINDOW
Cut the window sash seal to the proper length.
Peel off the backing and attach the seal to the
underside of the window sash.
B]
B]
[]
INSTALL THE AIR CONDITIONER IN
THE WINDOW
Place the air conditioner on the sill with the
bottom mounting rail against its back edge.
Center it and close the window securely behind
the top mounting rail. It should be level or
slightly tilted to the outside. Use u level; about
a 1/3 bubble will be the correct case slant to the
outside.
/I
Type B screws
Extend the left and right accordion panels to
the vertical window sashes and attach, through
the holes in the panels, with 5 Type B screws,
as appropriate.
[] INSTALL SUPPORT BRACKET AND
FOAM TOP WINDOW GASKET
%
-4,CAUTION:
To prevent broken
glass or damage to
windows, on vinyl or other
similarly constructed
windows, attach the
window locking bracket to
the window side jamb with
one Type B screw.
Vinyl
Wood
Cut the foam top window gasket to the window
width.
Stuff the foam
between the glass
and the window
to prevent air and
insects from getting
into the room.
NOTE: If the gasket supplied does not fit your
window, obtain appropriate material locally to
provide a proper installation seal.
11
Troubleshooting Tips. GEAppliances.com
Possible Causes What To Do
Theair conditioner • Hake surethe air conditioner plug ispushed
does not start is unplugged, completely into the outlet.
Thefuse is blown/circuit • Checkthe house fuse/circuit breaker box and replace
breaker istripped, the fuse or reset the breaker.
Power failure. • Theunit will automatically restart in the settings lost
used after the power isrestored.
• There isa protective time delay (approximately
3 minutes) to prevent tripping of the compressor
overload. For this reason, the unit may not start
normal cooling for 3 minutes after it is turned
buck on.
The current interrupter • Pressthe RESETbutton located on the power cord plug.
device is tripped. • Ifthe RESETbutton will not stay engaged, discontinue
use of the air conditioner and contact u qualified
service technician.
Air conditioner does Airflow is restricted. • Hake surethere are no curtains, blindsor furniture
not cool as it should blocking the front of the air conditioner.
Thetamp control may • Onmodels with touch pods: Inthe Cool mode, pressthe
not be set correctly. Decrease • pad.
• Onmodels with control knobs,turn the temperature
knob to u higher number.
The air filter isdirty. • Cleanthe filter at leastevery 30 days.
Seethe Careand Cleaningsection.
The room may have been hot. • When the air conditioner isfirst turned on,you need
to allow time for the room to cool down.
Cold air isescaping. • Checkfor open furnace registersand cold air returns.
Cooling coils have iced up. • See "Air conditioner freezing up" below.
Air conditioner
freezing up
Ice blocks the air flow
ond stops the oir conditioner
from cooling the room.
• Onmodels with control knobs,set the mode control at
High Fan or High Coolwith the Temp at 1 or 2.
• Onmodels with touch pads, set the controls at High Fan
or High Cool and set the thermostat to a higher
temperature.
Theremote control The batteries are inserted • Checkthe position of the batteries. They should be
is not working incorrectly, inserted inthe opposite (+)and (-)direction.
The batteries may be dead. • Replacethe batteries.
Water drips outside Hot, humid weather. • Thisisnormal.
The air conditioner is not • Forproper water disposal,make sure the air conditioner
tilted to the outside, slants slightlyfrom the case front to the rear.
Moisture removed from air • Thisisnormal for a short period in areaswith little
basepan and drains into base pan. humidity; normal for a longer period in very humid areas.
12
Normal Operating Sounds
iiiiiiiiii[_iii
Youmay hear a pinging noisecaused by
water being picked up and thrown against the
condenser on rainy days or when the humidity
is high.This designfeature helpsremove
moisture and improve efficiency.
Youmay hear the thermostat clickwhen the
compressor cycles on and off.
Water will collect in the basepan during
high humidity or on rainy days.Thewater
may overflow and drip from the outdoor side
of the unit.
Thefan may run even when the compressor
does not.
Page is loading ...
Page is loading ...
GEAir Conditioner-One-Vear Limited Warranty. (Forcustomers in theU.S.AJ
Staple your receipt here.
Proof of the original purchase date is
needed to make a warranty claim.
We Will Replace:
Onevear Replacement unit for any product which fails due to a defect in materials or workmanship.
Fromthe date of the I The replacement unit iswarranted for the remainder ofyour product's original one-year
originalpurchase I warranty period.
Properly pack your unit. We recommend using the
original carton and packing materials.
Return the product to the retail location where it
was purchased.
Include in the package a copy of the sales receipt or
other evidence of date of original purchase. Also print
your name and address and a description of the defect.
Customer instruction. This owner's manual provides
information regarding operating instructions and
user controls.
Improper installation, delivery or maintenance. If you
have an installation problem, or if the air conditioner is
of improper cooling capacity, contact your dealer or
installer. You are responsible for providing adequate
electrical, plumbing and other connecting facilities.
Failure of the product resulting from modifications to
the product or due to unreasonable use, including failure
to provide reasonable and necessary maintenance.
Replacement of house fuses or resetting of circuit
breakers.
Failure due to corrosion on models not corrosion-
protected.
Damage to the product caused by improper power
supply voltage, accident, fire, floods or acts of God.
Incidental or consequential damage caused by possible
defects with this air conditioner.
Damage caused after delivery.
EXCLUSION OF IMPLIED WARRANTIES--Your sole and exclusive remedy is product replacement
as provided in this Limited Warranty. Any implied warranties, including the implied warranties of
merchantability or fitness for a particular purpose, are limited to one year or the shortest period
allowed by law.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for
home use within the USA.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state. To know
what your legal rights are, consult your local or state consumer affairs office or your state's Attorney General
Exclusion of implied warranties: Except where prohibited or restricted by law, there are no warranties,
whether express, oral or statutory which extend beyond the description on the face hereof, including
specifically the implied warranties of merchantability or fitness for a particular purpose.
Warrantor: General Electric Company. Louisville, KV 40225
Z5
6EAir Conditioner-One-Vear Limited Warranty. (Forcustomers in Canada)
Staple your receipt here.
Proof of the original purchase date is
needed to make a warranty claim.
wi,
One Year I Replacement unit for any product which fails clueto a defect in materials or workmanship.
Fromthe date of the I The replacement unit iswarranted for the remainder ofyour product's original one-year
originalpUrehase I warranV period.
Properly pack your unit. We recommend using the
original carton and packing materials.
Return the product to the retail location where it
was purchased.
Include in the package a copy of the sales receipt or
other evidence of date of original purchase. Also print
your name and address and a description of the defect.
Customer instruction. This owner's manual provides
information regarding operating instructions and
user controls.
Improper installation, delivery or maintenance. If you
have an installation problem, or if the air conditioner is
of improper cooling capacity, contact your dealer or
installer. You are responsible for providing adequate
electrical, plumbing and other connecting facilities.
Failure ofthe product resulting from modifications to
the product or due to unreasonable use, including failure
to provide reasonable and necessary maintenance.
Replacement of house fuses or resetting of circuit
breakers.
Failure due to corrosion on models not corrosion-
protected.
Damage to the product caused by improper power
supply voltage, accident, fire, floods or acts of God.
Incidental or consequential damage caused by possible
defects with this air conditioner.
Damage caused after delivery.
EXCLUSION OF IMPLIED WARRANTIES--Your sole and exclusive remedy is product replacement
as provided in this Limited Warranty. Any implied warranties, including the implied warranties of
merchantability or fitness for a particular purpose, are limited to one year or the shortest period
allowed by law.
This warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada
for home use within Canada.
Some provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above
exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights
which vary from province to province. To know what your legal rights are inyour province, consult your local or
provincial consumer affairs o_ce.
Exclusion of implied warranties: Except where prohibited or restricted by law, there are no warranties,
whether express, oral or statutory which extend beyond the description on the face hereof, including
specifically the implied warranties of merchantability or fitness for a particular purpose.
Warrantor: Mabe Canada Inc.,
Burlington, Ontario
16
Page is loading ...
Page is loading ...
VERTISSEMENT !
UTILISATION DE RALLONGE5
RISQUED'INCENDIE. Peut occasionner des
blessures graves ou la mort.
• NE PASutiliser de rallonge avec ce climatiseur.
• NE PASutiliser de parasurtenseur ou
d'adaptateur h prises multiples avec ce
climatiseur.
www.electromenagersge.co
LISEZET5UIVEZ 501GNEUSEMENT CESCONSIGNESDE
J J
5ECURITE.
CONSERVEZ CES INSTRUCTIONS
19
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
ConsumerSupport.
I_l GEAppliances Website IntheU.S.A.:GEAppliances.com
Have a question or need assistancewith your appliance?Try the GEAppliancesWebsite 24 hours a day,
any day of the year! Forgreater convenience andfaster service,you can now download Owner's Manuals,
or evenorder parts on-line. InCanada: www.GEAppliances.ca
Real Life Design Studio In the U.S.A.:GEAppliances.com
GEsupports the Universal Designconcept-products, servicesand environments that can be used by
people of all ages,sizesand capabilities. We recognizethe need to designfor a wide range of physical
and mental abilities and impairments. Fordetails of GE'sUniversalDesignapplications, including kitchen design
ideasfor people with disabilities,check out our Website today. Forthe hearing impaired, pleasecall 800.TDD.
GEAC(800.833./4322).
In Canada, contact: Manager, Consumer Relations,MabeCanada Inc.
Suite310, 1 Factory Lane
Moncton, N.B.E1C91v13
Parts and Accessories
In the U.S.A.: GEAppliances.com
Individuals qualified to servicetheir own appliances can have parts or accessoriessent directly to their homes
(VISA,MasterCard and Discovercards are accepted).Order on-line today, 24 hours every day or
by phone at 800.626.2002 during normal businesshours.
Instructions contained in this manual cover procedures to be performed by any user. GE does not support
any servicing of the air conditioner. We strongly recommend that you do not attempt to service the air
conditioner yourself.
Customers in Canada should consult theyellow pagesfor the nearest Mabe servicecenter,
or call 1.800.561.33/44.
Contact Us
In the U.S.A.: GEAppliances.com
If you are not satisfied with the serviceyou receivefrom GE,contact uson our Website with all the details
including your phone number, or write to: General Manager, Customer Relations
GEAppliances,Appliance Park
Louisville,K¥/40225
In Canada: www.GEAppliances.ca, or write to: Director, Consumer Relations, Mabe Canada Inc.
Suite 310, 1 Factory Lane
Moncton, N.B. E1C91v13
Printed in China
/
