Haier ES80H-T1 (E) Operating instructions

Brand: Haier

Model: ES80H-T1 (E)

Type: Operating instructions

This manual is also suitable for

Haier Household Electric Water Heater

Operating Instructions

Please read this manual carefully before use.

Please keep this manual properly for future reference.

Version: 1st edition in

2010

Special No.: 0040503438

V98497

Safety Precautions (please read before use)

Installation Instructions

Meaning of signs

Prohibition Warning

Warning

Grounding

It means that the actions

must be prohibited.

Once you find any abnormality or smell burnt odor,

please disconnect the water heater from power supply

immediately and contact Haier service center.

Be sure to use an independent power supply of

220V/50Hz.

Do not use a damaged power cord or power socket.

Please dust off the power plug and the socket in a

timely manner.

Please install the water heater on a solid and firm

wall.

Please check whether the ammeter and the diameter

of wire are in conformity with the water heater’s rated

current, and if necessary, ask a qualified technician

to check the circuitry.

It is prohibited to touch the plug with wet hands.

Please avoid the water heater and its plug, socket

and remote controller being wetted by water. If they

are inadvertently wetted, be sure to ask a qualified

technician authorized by our company to check and

confirm safe operation before using the water heater

again in order to avoid electric shock.

Do not install the water heater on the floor. Do not

install the water heater in a place without water

drainage facilities.

It is prohibited to put inflammable and explosive

substances near the water heater.

It is strictly prohibited to install or repair the water

heater before disconnecting it from power supply.

It is prohibited to repair, maintain, disassemble or

modify the water heater by an unprofessional

maintainer without authorization.

Be careful to avoid scald by hot water.

● It is prohibited to touch both the valve and pipe that

supply hot water.

● Be sure to feel and confirm water temperature to be

acceptable before shower.

Never use hot water made by the water heater as

drinking water or for other purposes.

Children must use the water heater under the

guidance of adults.

If the water heater will not be used for a long time,

please disconnect it from power supply and drain the

water tank of water heater by following the instruc-

tions in the section of “Cleaning and Maintenance”.

For the purpose of safety, the water heater should use

an independent and qualified socket (it is prohibited to

use a multifunctional socket) and should also be

reliably grounded. It is strictly prohibited to use the

water heater without reliable ground connection. In

addition, please check both live and neutral wires with

a test pencil for misconnection.

Due to relatively high power of the water heater, it is

recommended that a power socket matched with its

plug (16A) be used at the time of installation to ensure

its normal operation and domestic electrical safety.

It is strictly prohibited to install the water heater

outdoors.

It is strictly prohibited to install the water heater in a

place where ice may form, otherwise water tank and

water pipes may burst and thus cause scald and water

leakage.

In bitterly cold days, please take precautions to

prevent the water heater from damage due to freezing.

To avoid danger, the damaged power cord must be

replaced by the manufacturer, the repair center or an

authorized full-time maintainer.

domestic ground wire is charged; in this case, you should

immediately stop using the water heater, pull out its power

plug from the socket and contact Haier after-sales service

center or your property company to ask a qualified

electrician for system inspection until the sign goes out.

It is the special sign of “safety

early-warning expert” of Haier

Water Heater Company.

Adopting Haier’s patented

technology, the “safety

early-warning expert” ensures

your safe shower and

meanwhile always monitors

your domestic ground wire for

charge. When the sign lights

up, it means that your

It means that the actions

must be taken.

Caution

It means that the matters

must be paid attention to.

Warning! Improper operation may cause personal injury or death!

Caution! Improper operation may cause personal injury or property loss!

Safety sign of Haier

water heater

Warning

Prohibition

Caution

Warning

Components

Heating

keep

warm

Now

Preheat

Mode choice

Night-elec

technology

Heat

preservation

Water heater

Remote

controller

Shower head

Hot water pipe

Cold water pipe

Water flow

sensor

Flow direction of cold water

Flow direction of hot water

Cold water

supply

Hot water supply

Remote

controller

holder

Cell replacement

Installation of

the relief valve

Installation method

Precautions for installation

Description of keys Description of icons

Cell scrapping

When the cell of remote controller is fully discharged,

open the cell cover with a one-yuan coin in the direction

as marked on the back of remote controller.

Install the relief valve (with the connection of G1/2)

onto the water inlet pipe in the direction of arrow

marked on the relief valve (the arrow points to the

water heater). When the water heater is turned on

to heat water, water in the water tank will expand,

so it is normal that several water drops may drip

from the pressure relief vent of relief valve to reduce

water pressure. Be sure to keep the pressure relief

vent to the atmosphere and unblocked.

The drain pipe with relief valve is installed as

follows: connect one end of the drain pipe to the

pressure relief vent of relief valve and the other end

to the sewage system in order to prevent the room

from being polluted by water drops at the time of

pressure relief. The drain pipe can be shortened or

extended as required. The drain pipe connecting to

the relief valve should keep downwards and inclined

in frostless environment.

Remove the button cell and replace it with a standard cell

of the same specification. Please make sure that the cell’s

positive pole is face up.

Fully discharged cells must not be placed in

high-temperature environment or throw into fire, otherwise

they may burst. Please dispose these cells in accordance

with relevant national regulations.

Remark: The keys on the remote controller are used in the same

manner as their corresponding keys on the control

panel.

Note: It is recommended to use the remote controller near

and perpendicular to the water heater.

Reinstall the cell cover in place.

Small handle

of relief valve

Pressure relief vent

(connect to the drain pipe)

To set hour

To set minute

To enter/exit the “

Preheat

” mode

To turn on/off the water heater

To enter/exit the “

Mode choice

” mode

● The water heater is designed for wall mounting.

● Before installing the water heater, make sure that the connecting wires on the back of water

heater are connected firmly. Preinstall the relief valve, flow sensor and one elbow, install the

elbow with relief valve and another elbow respectively onto water inlet/outlet pipes (the handle of

relief valve is installed at the end near the water outlet pipe as shown in Fig. 2) and connect the

connecting terminals of flow sensor to its interface. Afterwards, install the drain pipe with relief

valve and seal it with sealing tape to avoid water leakage. Please add washers up to the elbow’s

loose joint when installing an elbow.

● Determine the installation location of water heater, drill four holes of 12mm in diameter and

65mm in depth with a churn drill on the wall according to the dimensions as shown in Fig. 1,

insert expansion hooks/bolts into corresponding holes and fix them, lift up the water heater to

make its wall brackets be hooked to the hooks and bolts, install plain washers, connecting wires

on the back of water heater and nuts onto the bolts in turn (as shown in Fig. 3), and then tighten

the nuts and check the water heater for firmness. Afterwards, install the accessories such as

relief valve by following the instructions in the section of “Installation of the relief valve” (only for

reference at the time of installation). Please seal them with sealing tape to avoid water leakage.

● For easy installation and disassembly of the water heater, it is recommended that G1/2 loose

joint be installed respectively in proper position of water inlet/outlet pipes. Determine the location

where water is to be supplied to and then connect water inlet/outlet pipes and tap water pipe

respectively. Afterwards, fill the water tank and check for water leakage; in case of water leakage,

please reconnect the pipes.

Note: Be sure to always hold the water heater until its wall brackets are hooked to the hooks firmly,

otherwise it may drop and cause personal injury or properly loss.

● When installing the water heater, keep a certain space (at least 300mm) for easy repair and maintenance in the future. If the water heater is

built in a cabinet, the right panel should be removable for easy removal of the plastic cover at the time of repair.

● Make sure that tap water pressure is within the range of 0.05MPa~0.8MPa.

● The electric water heater should be installed in a room with ambient temperature above 0°C and the pipes should be in centralized layout. The

outlet of hot water should not be far away from the point of use. If the distance is more than 8m, please take proper measures for heat insulation

of hot water pipes to reduce heat loss.

● The wall on which the water heater is installed should be solid and firm and can bear four times the weight of water heater with its water tank full

of water. If the wall is not a bearing wall or is a hollow brick wall, be sure to take proper protective measures, e.g. addition of brackets, use of

through-wall screws and installation of back panel.

● The electric water heater should be installed in a location where is easy for use and repair and has a floor drain. In case of water leakage of

water tank or water pipe, the facilities around or under the water tank or water pipe should not be damaged. Avoid installing the water heater

above toilet bowl, bathtub, washbowl and door frame as possible to eliminate the feeling of oppression or unsafety.

● The power socket of water heater should be in a dry place without water spraying to ensure normal operation (it is recommended that the power

socket be equipped with waterproof case).

● Do not misconnect water inlet and outlet pipes. The relief valve should be installed in the specified position and its position must not be changed

without permission. Be sure to keep the pressure relief vent of relief valve to the atmosphere and unblocked.

● Check live and neutral wires with a test pencil for misconnection. Only after confirming that the water tank of water heater is full of water, no

water leakage occurs at each joint and power supply meets relevant requirements can you turn on the water heater to heat water.

To enter/exit the “

Night-electechnology

”

mode

It means that the water heater is heating

Time display

Icon of the “delay 1” mode

Icon of the “delay 2” mode

Icon of the “shower for a given number of persons” mode:

to indicate the number of persons to take a shower

When the “shower for one person” icon lights up, it means that the water

heater supplies hot water for one person to take a shower

When the “shower for two persons” icon lights up, it means that the water

heater supplies hot water for two persons to take a shower

When the “shower for three persons” icon lights up, it means that the water

heater supplies hot water for three persons to take a shower

It means that the water heater is in the

“low electricity price at night” mode

It means that the water heater is in the

“warm-keeping at medium temperature”

mode

It means that the water heater is in the

“3D heating” mode

Actual water temperature display

To enter/exit the “

Heat preservation

”

mode

Fig. 3

Fig. 2

Fig. 1

Volume

Press the “ ” key, the water heater will enter the “warm-keeping at

medium temperature” mode. In this mode, maximum heating temperature

is 40°C and not adjustable.

0.8

Cleaning and Maintenance Q & A

Specifications Packing List

Schematic circuit diagram

Appearance and components

Technical data

Packing list

Cleaning and maintenance

Q & A

● Be sure to disconnect the water heater from power supply before cleaning.

● Gently wipe the exterior with a piece of wet cloth and a little neutral detergent. Do

not use gasoline or other solutions. Finally, wipe the exterior with a piece of dry

cloth and keep the water heater dry. Do not use any detergent containing

abrasive (e.g. toothpaste), acid, chemical solvent (e.g. alcohol) or polishing

agent.

To keep high-efficiency operation, please clean heating tubes and inner water tank

once every three years. At the time of cleaning, be careful not to damage the

protective coating on the exterior of heating tubes and on the surface of inner water

tank.

● Be sure to disconnect the water heater from power supply before cleaning the

inner water tank.

● Before cleaning, close the water inlet valve, open the water outlet valve, remove

the “shockproof wall” shell and magnesium rod (at this time, you may also check

the loss of magnesium rod for timely replacement. Note: magnesium rod must be

purchased additionally.), drain the water tank, and then open the water inlet valve

to wash the inner water tank again and again for several minutes until clean

water flows out, and finally reinstall the magnesium rod and “shockproof wall”

shell in place.

● When the water heater is in use, check the relief valve once a month

as follows: pull the small handle of relief valve at the side of water

inlet pipe (be careful not to hurt your hands), if water flows out, it

means the relief valve is in normal operation; if no water flows out,

please contact local Haier after-sales service center; if the relief

valve is damaged, please replace it with a new relief valve of the

same specification.

● Ask an after-sales service technician for safety inspection on a

regular basis, remove the scale of heating tubes in a timely manner

and check the loss of magnesium rod, and if necessary, replace the

magnesium rod in time.

If the water heater will not be used for a long time, please do as follows:

1. Close the tap water pipe valve.

2. Connect one end of drain pipe to the pressure relief vent of relief

valve and then open the handle of relief valve.

3. Open the hot water valve fully (in the meanwhile, remove the hose

of shower head from the water outlet valve; at this time, be careful to

avoid scald by hot water) to drain the inner water tank.

To avoid personal injury, when you use the water heater again, it is

recommended to open the hot water valve before turning on the power

switch of water heater to discharge the air in the pipe; at this time,

smoking or other open flame is prohibited near the open valve. In

addition, thoroughly check whether each component of the water heater

is in good condition and confirm whether inner water tank is full of water

before using the water heater.

L: live wire (brown)

N: neutral wire (blue)

PE: ground wire (yellow and green)

MT1/MT2: manual reset thermostat

EH: heating tube

RT: sensor

Front view Sectional view Side view

A. Hot water outlet B. Cold water inlet C. Heating tube D. Enamel inner water tank E. Magnesium rod

Display panel

Electric

leakage coil

Relay Relay Relay

Model

Component

Electric

water

heater (set)

Relief

valve and

drain pipe

(set)

Expan-

sion bolt

(pc

Expan-

sion

hook

(pc)

Operat-

ing

Instruc-

tions (pc)

Remote

control-

ler (pc)

Water

flow

sensor

(pc)

Elbow

(pc)

Hidden

cover

(pc)

Washer

(pc)

Qty.

Model

Note: For the above parameters (dimensions and weight), permissible error is ±10%.

Volume Specified

power

supply

Rated

power

Rated

pressure

Rated

tem-

pera-

ture

Grade

water-

proof

Tap

water

pres-

sure

Net

weight

(storage)

Warning!

The water heater must be repaired and maintained by a qualified technician only. Improper operation may cause

serious injury or property loss.

Cleaning Check

Nonuse for a long time

Cleaning of the exterior

Cleaning of the interior

Phenomenon

Items to be confirmed

Solutions

① Whether the water supply system is cut off or

whether water pressure is too low

Check

No water outflow

② Whether the water outlet is clogged or whether the

hot water valve is opened

Check and clean

① Whether the hot water outlet is opened

Check and open

② Whether water temperature is set properly

Moderately raise the set temperature, wait until the water heater

heats water to the newly set temperature and then control cold

and hot water flow via the mixing valve

③ Whether the heating time is too short to heat

water to the set temperature

Wait until the water heater heats water to the set temperature (at

this time, the “heating” icon goes out) and then use water

Cold water flows out

④ Whether any component is damaged

If not ①②③, please contact the repair center

① Whether current function mode is set correctly

Refer to the description o operating modes in the section of

“Operating Instructions”, select the “shower for a given number of

persons” and moderately increase the number of persons to take

a shower

Water temperature does not

reach the required temperature or

a small amount of water flows out

② Whether tap water pressure is too high

Reduce water flow of the mixing valve

Water flow and water temperature

are unstable

Whether tap water pressure is stable

Reduce water flow of the mixing valve or use after water

pressure becomes stable

① Whether power supply is connected well

Check the power socket

The water heater fails to turn on

or the display screen does not

light up

② Whether any component is damaged

If not ①, please contact the repair center

E1 is displayed

Circuit failure

Please contact the repair center

① Whether inner water tank is full of water

Turn off the water heater, fill inner water tank with water and turn

on the water heater again

E2 is displayed

② Whether any component is damaged

If not ①, please contact the repair center

① Whether room temperature is below -20�

Turn off the water heater and turn on it again when ambient

temperature is above -19� , the water heater will return to normal

state

E3 is displayed

② Whether the sensor is damaged

If not ①, please contact the repair center

Press the “ (hour)” key or the “ (minute)” key, the

clock will flash.

Press the “ (hour)” key continuously to set the hour.

Press the “ (minute)” key to set the minute.

Press the “ ”, “ ”, “ ” or “ ” to

confirm the time setting (if no operation is made in 6s, the

time setting will also be confirmed automatically).

Note: The time setting of water heater adopts the 24-hour

system. Please ensure correct clock setting,

otherwise the “low electricity price at night” and “delay

shower” modes will not function normally.

Press the “ ” key, the icon of “delay ” mode

and the icon of clock display will flash simultaneously, at

which time you may set the “delay ”.

Press the “ (hour)” key continuously to set the hour.

Press the “ (minute)” key continuously to set the minute.

The setting of “delay ” is the same as that of “delay ”.

Note:

● Please use the “delay shower” mode after calibrating the

clock.

● You may set and store time respectively for “delay ” and

“delay ”.

Press the “ ” key, the water heater will enter the “delay shower”

mode. In this mode, the water heater finishes heating water and keeps water

warm before the delay time you set according to the water temperature

setting.

● In this mode, you may switch to “delay ”, “delay ” or “delay ” by pressing

the “ ” key.

● You may set the time respectively for “delay ” and “delay ” by following

the instructions in the section of “setting of the delay time”.

Operating Instructions

3D heating mode

Turn-on Clock calibration

The “shower for a given number of persons” mode:

The “warm-keeping at medium temperature” mode:

The “low electricity price at night” mode:

The “delay shower” mode:

Description of operating modes

After finishing the installation of a new water heater, there is no water in its water tank, please open the tap water inlet valve and mixing valve,

adjust the mixing valve to provide the most hot water, close the water outlet valve after water flows from the shower head or water outlet

continuously (it means that the water tank is full of water) and turn on the water heater after confirming no water leakage at each joint.

The water heater allows you to choose the desired mode from the following operating modes according to your actual need: the “shower for a given

number of persons” mode, the “delay shower” mode, the “warm-keeping at medium temperature” mode and “low electricity price at night” mode.

Plug in the water heater, the display screen will light up for 2s.

Clock calibration is done when the water heater is in power-on

state.

Power-down memory

Setting of the delay time

The water heater can memorize the operating mode before

power-down.

Automatic temperature control

Being set with the function of automatic temperature control,

when the water heater heats water to the temperature

corresponding to the “shower for a given number of persons”

mode, it will enter the warm-keeping mode and the “warm-

keeping” icon will light up. In the warm-keeping mode, the water

heater will keep such a cycle that it automatically reheats water

to the set temperature and then keep water warm.

Press the “ ” key to set the number of persons to take a shower.*

The water heater will automatically heat water for the selected number of persons to

take a shower.

* Note: The water heaters with volume of 40L, 50L and 60L can be set as “shower for

one person” or “shower for two persons”, while those with volume of 80L can be set

as “shower for one person”, “shower for two persons” or “shower for three persons”.

Press the “ (ON/OFF)” key (the water heater will enter the standby

mode or the operating mode before power failure).

Press the “ ” key, the water heater will enter the “low electricity price

at night” mode. In this mode, the water heater activates the heating or

warm-keeping function during 00:00~06:00 according to the water tempera-

ture setting.

● According to the electricity price system in some regions, the electricity

price during 00:00~06:00 is lower than that during other hours, so it is

easy to achieve cost saving by selecting the “low electricity price at night”.

● In this mode, the water heater does not heat or keep warm during those

hours other than 00:00~06:00.

After the water heater starts, it can automatically select the activation of 3D heating mode by detecting water temperature in the water tank

and hot water flow. In the 3D heating mode, the water heater heats water at high power to provide more hot water.

Water temperature in the water tank ≤69°C: If water flow is less than 2.5L/min, the 3D heating mode will not activate; if water flow is more

than or equal to 2.5L/min, the 3D heating mode will activate.

Water temperature in the water tank ≥70°C: If water flow is less than 3L/min, the 3D heating mode will not activate; if water flow is more

than or equal to 3L/min, the 3D heating mode will activate.

Shower for

one person

Shower for

two persons

Shower for

three persons

Press the

“ ” key

Press the

“ ” key

Press the

“ ” key

Preheat

Night-elec

technology

Heat

preservation

Preheat

Night-elec

technology

Preheat

Heat

preservation

Haier ES80H-T1 (E) Operating instructions

Brand: Haier

Model: ES80H-T1 (E)

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Haier ES80H-T1 (E) Operating instructions

This manual is also suitable for

Haier ES80H-T1 (E) Operating instructions

Related papers

Other documents