Zenith L15V36 Series User manual

SERVICE MANUAL

Product Type: LCD TV

Chassis: ML-012C

Manual Series:

Manual Part #:

Model Line:

Product Year: 2003

L15V36

Model Series:

CONTENTS

Specifications ..............................................................3

Description of Controls .................................................4

Adjustment Instructions ................................................9

Diagrams ...................................................................12

Parts List ...................................................................17

Schematics....................................................................

Published June 2002

by Technical Publications

Zenith Electronics Corporation

201 James Record Road

Huntsville, Alabama 35824-1513

Printed in Korea

- 2 -

PRODUCT SAFETY

IMPORTANT SAFETY NOTICE

This manual was prepared for use only by properly trained audiovisual service

technicians. When servicing this product, under no circumstances should the

original design be modified or altered without permission from Zenith

Electronics Corporation. All components should be replaced only with types

identical to those in the original circuit and their physical location, wiring, and

lead dress must conform to original layout upon completion of repairs. If any

fuse (or Fusible Resistor) in this TV receiver is blown, replace it only with the

factory specified fuse type and rating. When replacing a high wattage resistor

(Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB.

Always keep wires away from high voltage or high temperature parts.

Special components are also used to prevent shock and fire hazard.

These components are indicated by the letter “x” included in their component

designators and are required to maintain safe performance. No deviations are

allowed without prior approval by Zenith Electronics Corporation. Service work

should be performed only after you are thoroughly familiar with these safety

checks and servicing guidelines.

Circuit diagrams may occasionally differ from the actual circuit used.

This way, implementation of the latest safety and performance improvement

changes into the set is not delayed until the new service literature is printed.

CAUTION: Do not attempt to modify this product in any way.

Never perform customized installations without manufacturer’s

approval.

Unauthorized modifications will not only void the warranty, but may

lead to property damage or user injury.

GENERAL GUIDANCE

An lsolation Transformer should always be used during the servicing

of a receiver whose chassis is not isolated from the AC power line. Use a

transformer of adequate power rating to protect against personal injury from

electrical shocks. It will also protect the receiver and its components from being

damaged by accidental shorts of the circuitry that may be inadvertently

introduced during the service operation.

Before returning the receiver to the customer, always perform an AC leakage

current check on the exposed metallic parts of the cabinet, such as antennas,

terminals, etc., to be sure the set is safe to operate

without damage of electrical shock.

LEAKAGE CURRENT COLD CHECK

(ANTENNA COLD CHECK)

With the instrument’s AC plug removed from AC source, connect an electrical

jumper across the two AC plug prongs. Place the AC switch in the on position,

connect one lead of ohm-meter to the AC plug prongs tied together, and touch

other ohm-meter lead in turn to each exposed metallic parts such as antenna

terminals, phone jacks, etc. If the exposed metallic part has a return path to the

chassis, the measured resistance should be between 1MΩ and 5.2MΩ. When

the exposed metal has no return path to the chassis the reading must be

infinite. Any other abnormality that exists must be corrected before

the receiver is returned to the customer.

ELECTROSTATICALLY SENSITIVE DEVICES

Some semiconductor (solid-state) devices can be damaged easily by static

electricity. Such components commonly are called Electrostatically Sensitive

(ES) Devices. Examples of typical ES devices are integrated circuits and some

field-effect transistors and semiconductor “chip” components. The following

techniques should be used to help reduce the incidence of component damage

caused by static electricity.

1. Immediately before handling any semiconductor component or

semiconductor-equipped assembly, drain off any electrostatic charge on the

body by touching a known earth ground. Alternatively, obtain and wear a

commercially available discharging wrist strap device, which should be

removed for potential shock reasons prior to applying power to the unit under

test.

2. After removing an electrical assembly equipped with ES devices, place the

assembly on a conductive surface such as an ESD mat, to prevent

electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices

not classified as “anti-static” can generate electrical charges sufficient to

damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charge

sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until

immediately before you are ready to install it. (Most replacement ES devices

are packaged with leads electrically shorted together by conductive foam,

aluminum foil, or comparable conductive material.)

7. Immediately before removing the protective material from the leads of a

replacement ES device, touch the protective material to the chassis or circuit

assembly into which the device will be installed.

Caution: Be sure no power is applied to the chassis or circuit, and observe

all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES

devices. (Otherwise, seemingly harmless motion, such as the brushing

together of your clothing or the lifting of your foot from a carpeted floor, can

generate static electricity sufficient to damage an ES device.)

REGULATORY INFORMATION

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures: Reorient

or relocate the receiving antenna; Increase the separation between the

equipment and receiver; Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected; Consult the dealer or an

experienced radio/TV technician for help.

The responsible party for this device’s compliance is:

Zenith Electronics Corporation

201 James Record Road

Huntsville, AL 35824, USA

Digital TV Hotline: 1-800-243-0000

- 3 -

SPECIFICATIONS.................................................................4

DESCRIPTION OF CONTROLS...........................................5

ADJUSTMENT INSTRUCTION.............................................9

PRINTED CIRCUIT BOARD ...............................................12

BLOCK DIAGRAM...............................................................15

EXPLODED VIEW...............................................................16

EXPLODED VIEW PARTS LIST.........................................17

REPLACEMENT PARTS LIST............................................18

SCHEMATIC DIAGRAM..........................................................

TABLE OF CONTENTS

- 4 -

SPECIFICATIONS

Model L15V36 L20V36

Horizontal size (inch) 15.28 22.68

Height (inch) 15.17 18.64

Thickness (inch) 3.33 6.86

Weight (pound) 11.68 22.05

Power requirements DC 12V/3.5A

* CAUTION : For use only with Model No. SAD6012SE AC Adapter, manufactured

by H & E co., Ltd.

Television system NTSC

Television channels VHF : 2 ~ 13, UHF : 14 ~ 69

Cable : 01 ~ 125

Television Screen LCD Panel

Power consumption 45 W

External antenna impedance 75 Ω

Audio output 1 W + 1 W

Adapter (DC power) : In : AC 100-240V ~ 1.5A-0.6A

50/60Hz, 115~180VA

Out : DC 12V, 5A

* CAUTION : For use only with Model No. SAD6012SE AC Adapter, manufactured

by H & E co., Ltd.

Power supply cordset : Standard North America three wire earth-grounding with

flexible cord SJT type or higher type.

* CAUTION : If replacement becomes necessary, replace it with an exact duplicate.

Contact any Zenith authorized service center.

- 5 -

DESCRIPTION OF CONTROLS

Front of the

TV

MONO DPM

STEREO

ST

SAP

MONO DPM

SAP

STEREO

ST

Remote Control Sensor

DPM Indicator

(Only L15V36 models)

SAP Indicator

Mono Indicator

Stereo Indicator

Power/Standby indicator

Illuminates red in standby mode, Illuminates

green when the TV is turned on.

- 6 -

DC IN (15V)

ANT IN

+75 Ω

COMPONENT(480i/480p/720p/1080i)

VIDEO IN

DVD/DTV IN

AUDIO

RLVIDEO

P

R

P

B

Y L R

AUDIO(MONO)

DC 12V

ANT IN

+75 Ω

PC INPUT

COMPONENT(480i/480p/720p/1080i)

PC

SOUND

VIDEO IN

DVD/DTV IN

AUDIO

RLVIDEO

P

R

P

B

Y L R

AUDIO(MONO)

Back of the

TV

Audio/Video input

- This manual mainly explains for L15V36 connections.

PC input

PC sound input

Antenna input

DC 12V input

DVD/DTV IN

(Component (480i/480p/720p/1080i),

AUDIO) input

L15V36

L20V36

Kensington

Security System

Connector

DC 15V input

DESCRIPTION OF CONTROLS

- 7 -

MONO DPM

STEREO

ST

SAP

Side of the

TV

Side Control Panel

Side Connection Panel

Channel Buttons

Volume Buttons

Enter Button

Menu Button

TV·Video Button

Power Button

Headphone Jack

S-Video Input

Video Input

Audio Input

DESCRIPTION OF CONTROLS

- 8 -

powermute

tv/video

multimedia

mts

fcr

ch

vol

enter

123

456

789

0

vol

exit

menu

audio

flashbkcc sleep

video

pip position

pip input

ch

POWER

MTS

EXIT

VOLUME (

F G

)

MUTE

NUMBERS

CHANNEL (

DE

)

TV/VIDEO

Select: TV, Video 1, Video 2, S-

video

, Component, RGB-PC

(Only select

RGB-PC in

L15V36

model)

FCR

MULTIMEDIA

Select: TV or Component,

DASP

CC

Only L15V36:

PIP

POSITION

PIP INPUT

PIP CHANNEL (

DE

)

MENU

APC

FLASHBK

:Press the FLASHBK button

to view the last program you

were watching.

Remote Control Buttons

SLEEP

DESCRIPTION OF CONTROLS

- 9 -

1. Application Object

This instruction is for the application to the LCD TV.

2. Notes

(1) This set uses an adapter, so connect the adapter to the TV

correctly before adjustment.

(2) These adjustments must be performed in the correct

sequence.

(3) These adjustments must be performed at 25

!5cC of

temperature and 65!10% of relative humidity.

(4) The input voltage of the receiver must be kept at

100~220V, 50/60Hz during adjustment.

(5) The set must be operated for 30 minutes before

adjustment. Heat Run must be performed with the full white

signal or a TV noise signal.

3. Component Mode Adjustment

: Component Model only

3-1. Required Test Equipment

(1) MSPG-925LTH, Pattern Generator for Digital TV 1080i

mode Color-Bar signal output, Digital TV Set-Top Box

(2) This time the Y input signal Level which passes the input

vertical resistance of the Set must become the 1Vp-p.

(3) Remote controller for adjustment (SVC Remocon)

3-2. Preparation for Adjustment

(1) Perform Heat Run for more than 30 minutes with a white

pattern.

(2) Connect the signal from a pattern generator to the LCD

TV’s component Input Jack.

3-3. YPbPr ADJUST Adjustment

(1) Receive the Color Bar Pattern signal of Digital TV 1080i

Mode from Pattern Generator.

(2) Select the YPbPr ADJUST of the adjustment mode(SVC

Menu Mode) by pressing the IN-START Key(or SVC Key)

on the remote controller for adjustment(SVC).

(3) Start the adjustment by pressing the F, G Key(Volume

Key) in the YPbPr ADJUST of the adjustment mode.

(4) The “To Set” letter of OSD Box top of the screen center is

exchanged with the “OK” and when, it completes a

adjustment.

4. PC Input Mode Adjustment

: 15 Inch Model only

4-1. Required Test Equipment

(1) 801GF(or VG819), Pattern generator with a Gray Pattern

of 16(11) tones.

(2) Remote controller for adjustment (SVC Remocon)

4-2. Preparation for Adjustment

(1) Perform Heat Run for more than 30 minutes with a white

pattern.

(2) Connect the signal from a pattern generator to the LCD

TV’s PC Input Jack(D-Sub).

4-3. Auto Gray Adjustment

(1) Apply the gray signal of XGA(1024X768) 16 tones(H: 31-

214 Pattern, V: 60-84 Pattern) by using 801GF.

Or apply the gray signal by using VG819, Pattern

generator with a Gray Pattern of 16(11) tones.

(2) Select the adjustment mode(SVC Menu Mode) by pressing

the ADJ Key(or SVC Key) on the remote controller for

adjustment(SVC) and adjust the Auto gay from 0 to 1 by

using Volume + Key.

ADJUSTMENT INSTRUCTION

- 10 -

ADJUSTMENT INSTRUCTION

5. Position of Mode Adjustment

: 15 Inch Model only

Timing of Mode Table * H[dot]/V[line]

Mode

H_total

H_display

H_blanking

H_sync

H Polarity

H_bp

H_fp

H-freq[kHz]

/Clk[MHz]

V_total

V_display

V_blanking

V_sync

V Polarity

V_bp

V_fp

VGA-60

800

640

160

96

NEG.

48

16

31.469

25.175

525

480

45

2

NEG

33

10

VGA-67

864

640

224

64

NEG.

96

64

35.0

30.24

525

480

45

3

NEG

39

3

VGA-72

832

656

176

40

NEG.

120

16

37.861

31.5

520

496

24

3

NEG

20

1

VGA-75

840

640

200

64

NEG.

120

16

37.5

31.5

500

480

20

3

NEG

16

1

VGA-85

832

640

192

56

NEG.

80

56

43.269

36.0

509

480

29

3

NEG

25

1

SVGA-56

1024

800

224

72

POS

128

24

35.156

36.0

625

600

25

2

POS

22

1

SVGA-60

1056

800

256

128

POS

88

40

37.879

40.0

628

600

28

4

POS

23

1

SVGA-72

1040

800

240

120

POS

64

56

48.077

50.0

666

600

66

6

POS

23

37

Mode

H_total

H_display

H_blanking

H_sync

H Polarity

H_bp

H_fp

H-freq[kHz]

/Clk[MHz]

V_total

V_display

V_blanking

V_sync

V Polarity

V_bp

V_fp

SVGA-75

1056

800

256

80

POS

160

16

46.875

49.5

625

600

25

3

POS

21

1

SVGA-85

1048

800

248

64

POS

152

32

53.674

56.25

631

600

31

3

POS

27

1

XGA-60

1344

1024

320

136

NEG

136

160

48.363

65.0

806

768

38

6

NEG

29

3

XGA-70

1328

1024

304

136

144

24

56.476

75.0

806

768

38

6

NEG

29

3

XGA-75

1312

1024

288

96

POS

176

16

60.023

78.75

800

768

32

3

POS

28

1

MAC-75

1152

832

320

64

NEG

224

32

49.725

57.283

667

624

43

3

NEG

39

1

XGA-85

1376

1024

352

96

POS

208

48

68.677

84.997

808

768

40

3

POS

36

1

- 11 -

ADJUSTMENT INSTRUCTION

Mode

H_total

H_display

H_blanking

H_sync

H Polarity

H_bp

H_fp

H-freq[kHz]

/Clk[MHz]

V_total

V_display

V_blanking

V_sync

V Polarity

V_bp

V_fp

VGA350-70

800

640

160

96

POS

48

16

31.468

25.17

449

350

99

2

NEG

60

37

VGA350-85

832

640

192

64

POG

96

32

37.86

31.47

445

350

95

3

NEG

60

32

VGA400-70

800

640

160

96

NEG

48

16

31.46

25.17

449

400

49

2

POS

35

12

VGA400-85

832

640

192

64

NEG

96

32

37.86

31.5

445

400

45

3

POS

41

1

6. EDID(The Extended Display Identification Data)

: 15 Inch Model only

00

10

20

30

40

50

60

70

00

01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

00

14

81

01

26

00

FF

0B

50

40

01

30

32

FF

01

54

81

01

18

55

FF

01

BF

80

01

88

1E

FF

78

E8

01

36

46

FF

1F

80

01

00

0D

FF

17

31

10

01

0E

00

70

59

0E

01

C3

0A

30

E8

3B

01

F9

01

10

20

E5

C3

D9

01

15

01

00

20

D7

A0

45

01

64

00

20

3A

A3

59

01

19

1E

20

01

54

61

01

00

20

00

4C

59

01

40

00

20

00

97

71

01

41

00

24

59

01

00

FD

C8

- 12 -

PRINTED CIRCUIT BOARD

MAIN(TOP)

- 13 -

PRINTED CIRCUIT BOARD

MAIN(BOTTOM)

- 14 -

PRINTED CIRCUIT BOARD

CONTROL

SIDE A/V

LED ASSY

- 15 -

BLOCK DIAGRAM

- 16 -

EXPLODED VIEW

120

300

112

560

530

112

520

550

500

320

210

220

310

350

330

360

370

380

330

400

430

230

240

- 17 -

112 6306V15001A LCD MODULE,LC150X01-A3 IPS LG PHILPS TFT COLOR XGA

120 6400GKTX01A SPEAKER,FULLRANGE F1527C-6428 K-TONE (GENERAL) 8OHM 7/12W

210 4950V00141B METAL,SHIELD NON REAR AV 15LA60

220 4810V00764C BRACKET,REAR AV RU-15LA60 ML012B HIPS 40AF

230 4810V00765C BRACKET,SIDE AV RU-15LA60 ML012B HIPS 40AF

240 4950V00142A METAL,SHIELD NON SIDE AV, 20LA60/15LA60

250 4950V00134A METAL,MAIN FRAME NON 15LA60

300 3091V00490D CABINET ASSEMBLY,RU-15LA60 STEREO ML012B

310 5020V00777B BUTTON,CONTROL 15LA60 ABS, HF-380 7KEY

320 4950V00140A METAL,SHIELD NON 15LA60

330 4950V00157A METAL,STAND NON HINGE ASSY_15LA60

340 4810V00777B BRACKET,STAND 15LA60 NON ABS, HF-380 FRONT

350 4810V00778B BRACKET,STAND 15LA60 NON ABS, HF-380

360 4810V00776B BRACKET,DECO RZ-15LA60 NON ABS, HF-380 #102

370 4810V00779B BRACKET,STAND RZ-15LA60 NON ABS, HF-380 .

380 4950V00135A METAL,STAND NON BASE, 15LA60

400 3809V00338D BACK COVER ASSEMBLY,RU-15LA60 NON .

430 3550V00298B COVER,REAR 15LA60 HIPS 60HR .

520 6871VMMQ13A PCB ASSEMBLY,MAIN ML012B RU-15LA60

530 6871VSMV38A PCB ASSEMBLY,SUB CONT ML012B RZ-15/20LA60 CONTROL ASSY

540 6633VA0003N INVERTER ASSEMBLY,12V NON ECT ALPS500 6633VA00003K

550 6871VSMV40C PCB ASSEMBLY,SUB A/V ML012B RU-15/20LA60 SIDE A/V ASSY

560 6871VSMV43B PCB ASSEMBLY,SUB ML012B 15 INDEX LED ASSY

EXPLODED VIEW PARTS LIST

No.

PART NO.

DESCRIPTION

- 18 -

REPLACEMENT PARTS LIST

LOCA. NO PART NO DESCRIPTION

Q3004

Q3005

Q3006

Q301

Q350

Q801

Q901

Q902

Q903

Q904

D1

D2

D801

D802

D811

D812

ZD101

ZD3000

ZD71

ZD72

ZD73

ZD74

ZD75

ZD76

ZD77

ZD79

ZD80

ZD81

ZD82

ZD83

C101

C103

C105

C111

C113

C17

C20

C21

C214

C217

C220

C221

C2305

C24

0TR387500AA

0TR150400BA

0TR387500AA

0DD181009AB

0DD100009AM

0DD414809ED

0DZ330009BA

0DZRM00178A

0CE476DH618

0CE106DK618

0CE687DD618

0CE105DK618

0CE107DF618

0CE106DF618

0CE476DF618

0CE106DF618

0CE225DK618

0CE107DF618

CHIP 2SC3875S(ALY) KEC

CHIP 2SA1504S(ASY) KEC

CHIP 2SC3875S(ALY) KEC

KDS181 TP KEC - 85V 300MA

EU1ZV(1) TP SANKEN

1N4148 TP GRANDE

ZENERS,HZT33

ZENERS,UDZS TE-17 5.1B

47UF STD 25V 20%

10UF STD 50V M

680UF STD 10V 20%

1UF STD 50V M

100UF STD 16V M

10UF STD 16V M

47UF STD 16V M

10UF STD 16V M

2.2UF STD 50V 20%

100UF STD 16V M

LOCA. NO PART NO DESCRIPTION

IC1

IC2

IC201

IC202

IC3

IC350

IC351

IC501

IC600

IC601

IC603

IC604

IC605

IC701

IC801

IC806

IC901

IC902

IC903

IC904

IC905

IC906

IC907

IC908

IC909

IC914

IC915

IC941

IC942

IC802

IC803

IC804

IC805

IC913

Q102

Q204

Q205

Q206

Q3

Q3000

Q3001

Q3002

Q3003

0IZZVC0063B

0IAL241610B

0IAL242110A

0IMCRFA022A

0IFA752700A

0ISO204000A

0IMCRFA010A

0IMCRGN001B

0IMCRTI022D

0IMCRMN007A

0IKE704200J

0IMCRFA009A

0IMCRFA008A

0IMCRM3001A

0ITC786000A

0IMCRFA020A

0IMCRG2004B

0IPH806520A

0IPH743730E

0IZZVC0062B

0ISS416162C

0IPH740400G

0IMCRAL006A

0IMCRSJ001B

0IMCRFA020A

0IMCRTH001A

0IMMRHY033A

0IMCRTW002A

0IMCRFA020A

0TFVI80001A

0TFVI80005A

0TF492509AA

0TR387500AA

M37136EFSP DIP 52P ST ML012B

AT24C16A-10PI-2.7 8PIN DIP ST EEPROM NON

AT24C21-10SI-2.5 8P,SOP TP 1K EEPROM

74F14SC 14P SOIC R/TP SCHMITT TRIGGER IC

KA75270Z 3 TP RE-SET IC

CXA2040AQ 32P,QFP BK IIC BUS VIDEO

KA7809R 2P D-PAK, R/TP REGULATOR IC

FLI2310BC 208P PQFP TRAY DIGITAL VIDEO

TPA3004D2 48P PQFP TRAY 9WSTEREO AUDIO

MSP3421G QA B8 V3 80P QFP TRAY VIRTUAL DOLBY

KIA7042AF SOT-89 TP 4.2V VOLTAGE

KA78M08RTM 2P D-PAK, R/TP REGULATOR IC

KA78M05RTM 2P D-PAK, R/TP REGULATOR IC

MST9883A 80P LQFP TRAY A/D CONVERTER

SI786 28SSOP TP DUAL-OUTPUT POWER

RC1587DT_36 3P TO252 DPAK R/TP 2.5V

JAGASM A4 SAGE 352BALL

80C652 40 PLCC ST 8-BIT

74HCT373 D 20SOP R/TP ADDRESS LATCH

M27C512_10F1 DIP 32P ST ML012B

K4S161622E-TC80 50TSOP

74HC04D HEX INVERTER 14P,SOP TP

AT24C16AN-10SI-2.7 8P SOIC R/TP EEPROM

SC1565IST-2.5TR 2.5V 1.5A 3P SOT-223 R/TP POWER

RC1587DT_36 3P TO252 DPAK R/TP 2.5V

THC63LVDM83R 56P TSSOP R/TP TRANSMITTER IC

HY57V643220C(L)T-6 86P TSOP TRAY 64M

TW9908 100P PQFP TRAY VIDEO DECODER

RC1587DT_36 3P TO252 DPAK R/TP 2.5V

VISHAY SI4808DY R/TP SO-8 30V 7.5A OLD

VISHAY SI4963DY R/TP SO-8 -20V 6.2A

SI4925DY TP TEMIC 30V 6.1A SO-8

CHIP 2SC3875S(ALY) KEC

IC

TRANSISTOR

RUN DATE : 2003.6.11

For Capacitor & Resistors, the

charactors at 2nd and 3rd digit

in the P/No. means as follows;

CC, CX, CK, CN : Ceramic

CQ : Polyestor

CE : Electrolytic

RD : Carbon Film

RS : Metal Oxide Film

RN : Metal Film

RF : Fusible

DIODE

CAPACITOR

- 19 -

LOCA. NO PART NO DESCRIPTION

C25

C309

C31

C318

C320

C321

C332

C350

C353

C354

C360

C362

C363

C364

C365

C390

C391

C392

C406

C418

C493

C494

C495

C527

C532

C610

C614

C618

C619

C620

C621

C622

C631

C632

C633

C635

C638

C639

C640

C641

C642

C643

C656

C658

C659

C662

C669

C670

C672

C676

0CE227DF618

0CE106DF618

0CE105DK618

0CE107DD618

0CQ3331N509

0CE106DF618

0CE107DD618

0CE227DF618

0CE476DF618

0CE336DF618

0CE105DK618

0CE474CK636

0CE106SF6DC

0CE107SF6DC

0CE476DF618

0CE107SF6DC

0CE106DF618

0CE476DF618

0CE107DF618

0CK224DF56A

0CE476DF618

0CE106DF618

0CE335DK618

0CE107DF618

0CK224DF56A

0CK105DF64A

0CK224DF56A

220UF STD 16V M

10UF STD 16V M

1UF STD 50V M

100UF STD 10V M

0.033U 100V K

10UF STD 16V M

100UF STD 10V M

220UF STD 16V M

47UF STD 16V M

33UF STD 16V M

1UF STD 50V M

0.47UF SHL,SD 50V 20%

10UF MVG 16V 20%

100UF MVG 16V M

47UF STD 16V M

100UF MVG 16V M

10UF STD 16V M

47UF STD 16V M

100UF STD 16V M

220000PF 2012 16V 10%

47UF STD 16V M

10UF STD 16V M

3.3UF STD 50V 20%

100UF STD 16V M

220000PF 2012 16V 10%

1UF 2012 16V 20%

220000PF 2012 16V 10%

LOCA. NO PART NO DESCRIPTION

C677

C680

C681

C682

C683

C712

C719

C733

C734

C742

C801

C802

C803

C804

C805

C806

C807

C808

C814

C815

C817

C825

C826

C836

C837

C902

C904

C906

C911

C915

C935

C946

C953

C954

C974

JA2000

JA201

JA203

JA205A

JA205B

JA206

SJ205

L102

L651

L653

L655

L656

0CK224DF56A

0CE227DF618

0CK105DF64A

0CE107DF618

0CE107SF6DC

0CE107DD618

0CE107SF6DC

0CE107DD618

0CE476DK618

0CE477DF618

0CE227DH618

0CE107DH618

0CE475DK618

0CE337DH618

0CE227DF618

0CE227DD618

0CE106SF6DC

0CE107DF618

0CE107SF6DC

0CE106SF6DC

0CE107SF6DC

0CE476DF618

0CE477DF618

0CE476DF618

6613V00018A

6612VAH001A

6613V00004P

380-336E

380-336F

6612VCH003B

6612VJH008D

0LA0272K139

6140VR0005B

220000PF 2012 16V 10%

220UF STD 16V M

1UF 2012 16V 20%

100UF STD 16V M

100UF MVG 16V M

100UF STD 10V M

100UF MVG 16V M

100UF STD 10V M

47UF STD 50V M

470UF STD 16V 20%

220UF STD 25V M

100UF STD 25V M

4.7UF STD 50V 20%

330UF STD 25V M

220UF STD 16V M

220UF STD 10V M

10UF MVG 16V 20%

100UF STD 16V M

100UF MVG 16V M

10UF MVG 16V 20%

100UF MVG 16V M

47UF STD 16V M

470UF STD 16V 20%

47UF STD 16V M

JACK ASSEMBLY,PMJ026A(7PIN)

JACK,PHONE HEC3900-010110(7)

JACK ASSY,PJ6054P 3P

JACK,RCAWA6013E 1P

JACK,PHONE PEJ012C 1P

JACK,RCAPJ6063D DVD IN 3P

INDUCTOR,27UH K

COIL,ESLF7045T-330MR82

COIL,SLF7045T-330MR82

JACK

COIL & TRANSFORMER

REPLACEMENT PARTS LIST

- 20 -

LOCA. NO PART NO DESCRIPTION

L802

L803

T801

R2002

R2003

R803

R805

RA901

RA902

RA903

RA904

RA905

RA906

RA911

RA912

RA926

RA927

RA928

RA929

RA930

RA931

SW1101

SW1102

SW1103

SW1104

SW1105

SW1106

SW1107

SW1108

L1

L101

L103

L106

L107

L205

L206

L207

L2100

L2101

L2105

L2106

L2107

L2108

L2109

L215

6140VB0004B

6140VB0004A

6170VTCA30A

0RD1200H609

0RHZVTA001A

0RRZVTA001A

140-313B

6210TCE001G

6210TCE001A

6210TCE001G

6210TCE001A

6210TCE001G

6210TCE001A

COIL,CHOKE 26UH

COIL,CHOKE 9.5UH

TRANSFORMER,SMPS[COIL] EPC 13-Z 320UH

120 OHM 1/2 W 5.00%

0.025 OHM 1W 2%

MNR-14-E0A-J-101 R OHM 100 OHM 5%

SWITCH,TACT 2LEAD 160G

FILTER,EMC HH-1M3216-501

FILTER,EMC HB-1S2012-080JT

FILTER,EMC HH-1M3216-501

FILTER,EMC HB-1S2012-080JT

FILTER,EMC HH-1M3216-501

FILTER,EMC HB-1S2012-080JT

LOCA. NO PART NO DESCRIPTION

L216

L276

L277

L3

L300

L301

L302

L350

L601

L602

L603

L658

L7

L701

L702

L703

L704

L8

L801

L804

L805

L806

L901

L902

L904

L905

L908

L911

L913

L917

L918

L919

L920

L922

L923

L955

L956

L957

L958

R953

X1

X301

X501

X601

X901

JA202

P1102

6210TCE001A

6210TCE001G

6210TCE001A

6210TCE001G

6210TCE001A

6210TCE001G

6210TCE001A

6210TCE001G

156-A01P

156-A02X

6202VDT002J

156-A02M

6202VDT002B

6630G15E215

6631V20016G

FILTER,EMC HB-1S2012-080JT

FILTER,EMC HH-1M3216-501

FILTER,EMC HB-1S2012-080JT

FILTER,EMC HH-1M3216-501

FILTER,EMC HB-1S2012-080JT

FILTER,EMC HH-1M3216-501

FILTER,EMC HB-1S2012-080JT

FILTER,EMC HH-1M3216-501

RESONATOR,CRYSTAL HC49U 8.000MHZ

RESONATOR,CRYSTAL HC49U 27.000MHZ

RESONATOR,CRYSTAL SX-1 13.500000MHZ

RESONATOR,CRYSTAL HC49U 18.432MHZ

RESONATOR,CRYSTAL SX-1 SC14.3MHZ

CONNECTOR,D-SUB 15P 2.29MM

CONNECTOR ASSEMBLY,14P 2.0MM

FILTER & CRYSTAL

MISCELLANEOUS

REPLACEMENT PARTS LIST

SWITCH

RESISTOR

Page is loading ...

Zenith L15V36 Series User manual

Zenith L15V36 Series User manual

Related papers

Other documents