Optimus V-700DB2 User manual

CARDCARD

MENU

RESET

EJECT

CARDCARD

MENU

RESET

EJECT

z Refer to the included CD-ROM for the German, French, Spanish and Italian “INSTRUCTION MANUAL”.

z Die “BEDIENUNGSANLEITUNG” in den Sprachen Deutsch, Französisch, Spanisch und Italienisch

finden Sie auf der beiliegenden CD-ROM.

z Utilisez le CD-ROM fourni pour consulter le “MANUEL D’INSTRUCTIONS” en allemand, français,

espagnol et italien.

z Consulte en el CD-ROM suministrado el “MANUAL DE INSTRUCCIONES” en alemán, francés, español e

italiano.

z Per il “MANUALE DI ISTRUZIONI” in Tedesco, Francese, Spagnolo e Italiano, fare riferimento al CD-

ROM allegato.

e00_l8hbg_xe_7.book Page 1 Friday, November 5, 2004 10:21 AM

English 1

PRECAUTION

Location

For safe operation and satisfactory performance of your

unit, keep the following in mind when selecting a place for

its installation:

Shield it from direct sunlight and keep it away from sources

of intense heat.

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper heat

dissipation. Do not block the ventilation holes at the top and

bottom of the unit. Do not place the unit on a carpet

because this will block the ventilation holes.

Install the unit in a horizontal position only.

Avoid locations subject to strong vibrations.

Avoid moving the unit between cold and hot locations.

Do not place the unit directly on top of a monitor TV, as this

may cause playback or recording problems.

Avoiding Electrical Shock and Fire

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting it from

an AC wall outlet. Grasp it by the plug.

If any liquid is spilled on the unit, unplug the power cord

immediately and have the unit inspected at a factory-

authorised service centre.

Do not place anything directly on top of this unit.

SERVICE

This unit is a precision instruments and if treated with care,

will provide years of satisfactory performance. However, in

the event of a problem, the owner is advised not to attempt

to make repairs or open the cabinet. Servicing should

always be referred to your dealer or Sanyo Authorized

Service Centre.

WARNING: TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR OTHER MOISTURE.

To avoid electrical shock, do not open the cabinet.

Refer servicing to qualified personnel only.

If the power supply cord (AC power cord) of this appliance

is damaged, it must be replaced. Return to a SANYO

Authorised Service Centre for replacement of the cord.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type

recommended by the manufacturer.

Discard used batteries according to the manufacture’s

instructions.

e00_l8hbg_xe_7.book Page 1 Friday, November 5, 2004 10:21 AM

2 English

INTRODUCTION

Main features

 The digital video recorder records video from

monitoring cameras to its internal hard disk, it

can display the video being displayed on a

monitor split into four, nine or sixteen

screens, and it can also display recorded

video in the same way.

The DSR-3709P can only display split screen video in

four or nine screens.

 Separately-sold hard disks (80, 160, 250, or

300 GB) can be installed to further increase

this large memory capacity.

 Complete range of recording and playback

functions

z Simultaneous recording and playback of video.

z Timer recording allows recordings to be made at

different times each day.

z Zoom allows a certain section of live and playback

video to be magnified.

z Alarm recording allows the actions of intruders to be

recorded.

z The video from specific cameras can be masked

using a gray pattern to prevent it being monitored.

z Motion sensing can be used with each camera, and

alarms can be setup to give priority to the recording

of moving images.

z By connecting multiple digital video recorders, it is

possible to perform analog series recording in which,

once the capacity of one hard disk is reached,

recording continues automatically on the next digital

video recorder.

 Search function - lets you instantly display the

desired recording. (JP.30)

z Searching in order of alarm occurrence using alarm

search

z Searching by thumbnail using alarm search

z Searching by date/time

z Searching within the archive area

z Searching for intruder motion using motion detection

search

 Two-level security lock function - lets you

restrict users for data and equipment

management. (JP.89)

 Expandable, can be connected to a PC

z Recorded video can be copied to CompactFlash

cards and CD-R/RW.

z A built-in LAN terminal provides support for network

control, thus facilitating live monitoring, camera

control, playback, searches, and menu setting.

z

Monitoring can be carried out on two different monitor

screens - namely, the main monitor and monitor 2. In

addition, the main monitor can be viewed in split-

screen mode while the monitor 2 is used for full

screen viewing or automatic camera selection.

z Dome cameras can be controlled by button

operations on the digital video recorder.

z Images stored on a CompactFlash card can be

printed directly from a printer.

Accessories

Check that you have all the parts shown below.

Power cord

Core clamp (1)

For: Audio input/Audio

output cables

Power cord tie

z Instruction Manual (DVR)

z Manual for Remote

Operation by

Network

Connection

z Quick Guide

z CD-ROM Manual

Symbols used in this manual

Information describing operation methods

or how to get the most out of functions.

Information describing the correct use of

the digital video recorder.

(JP. xx) indicates the page to be referred to.

Copyright

z This manual and software are copyrighted by Sanyo

Electric Co., Ltd.

z Brand and product names used in this manual are the

trademarks or registered trademarks of their respective

companies.

Except for personal use, copyright law prohibits the use of

recorded copyrighted images without the permission of the

copyright holder.

e00_l8hbg_xe_7.book Page 2 Friday, November 5, 2004 10:21 AM

English 3

CONTENTS

1 BEFORE USE ................................................ 5

Notes on handling the internal HDD .............. 5

Notes on installation locations ....................... 5

The hard disk and cooling fan are consumable

components. .................................................. 6

Important recordings ...................................... 6

Protection of the hard disk ............................. 6

Backup battery ............................................... 6

2 NAMES AND FUNCTIONS OF PARTS ........ 7

Front panel ..................................................... 7

Rear panel ................................................... 10

3 INSTALLATION AND CONNECTIONS ...... 11

Basic connections ........................................ 11

Connecting RS-485 terminals ...................... 11

Connecting SANYO protocol devices

(Dome Cameras) .......................................... 13

Connecting an amplifier ............................... 13

Connecting ALARM IN terminals ................. 13

Connecting SENSOR ALARM OUT

terminals ....................................................... 14

Connecting CONTROL terminals ................. 14

Connecting the power cord .......................... 14

1 PREPARING FOR USE ............................... 15

Operation display area ................................. 15

Changing the position of the operation

display area .................................................. 16

Changing the language ................................ 16

Setting the time ............................................ 17

The internal hard disk .................................. 18

2 VIEWING VIDEO FROM A CAMERA ......... 19

Viewing on a full screen ............................... 19

Viewing on quad screens ............................. 19

Viewing on multi screens

(9 screens/ 16 screens) ............................... 20

Viewing on plus screen ................................ 20

Viewing with automatic screen selection ..... 21

Viewing on the monitor 2 ............................. 21

3 RECORDING ............................................... 23

Normal recording ......................................... 23

Timer recording ............................................ 23

Alarm recording ............................................ 24

Pre-alarm recording ..................................... 25

4 PLAYBACK ................................................. 26

Playing video on a full screen ...................... 26

Fast-forward and fast-rewind playback ........ 26

Changing the playback speed ...................... 27

Enlarging the playback video ....................... 27

Viewing still images ...................................... 28

Performing frame advance

(forward or reverse) ..................................... 29

Playing video on multiple screens ................ 29

5 SEARCHING FOR RECORDED VIDEO ..... 30

Alarm search ................................................ 31

Alarm thumbnail search ............................... 32

Time/date search ......................................... 32

Archive area search ..................................... 34

Motion detection search ............................... 34

6

SAVING (COPYING) RECORDED VIDEO

..... 38

Copying video to the hard disk’s

archive area ................................................. 39

Copying video to a CompactFlash card or

Microdrive ..................................................... 41

Printing images from CompactFlash cards

(quick print) .................................................. 43

Copying video to CD-R/RW ......................... 45

INTRODUCTION

OPERATION

e00_l8hbg_xe_7.book Page 3 Friday, November 5, 2004 10:21 AM

CONTENTS

4 English

OPERATIONINTRODUCTION SETTINGS OTHER

1 MENU CONFIGURATION AND

OPERATIONS ............................................. 47

Basic menu operations ................................ 47

Restoring menu setting items to

their default values ....................................... 48

Sub-menu configuration ............................... 49

2 INITIAL SET ................................................ 51

Initial settings ............................................... 51

Setting the time ............................................ 51

Setting the summer time .............................. 51

External clock setting ................................... 53

Detecting connected cameras ..................... 54

Setting camera titles .................................... 55

Setting holidays ............................................ 56

Setting time periods ..................................... 57

3 RECORD SET ............................................. 60

Settings for recording ................................... 60

Normal recording easy setup ....................... 60

Displaying the recording areas .................... 64

Changing recording areas ............................ 65

Setting overwrite permission ........................ 66

Setting recording conditions ......................... 67

Setting series recording ............................... 69

Setting auto deleting .................................... 71

Setting normal recording .............................. 71

Setting program recording ........................... 73

Timer settings .............................................. 74

Setting alarm recording ................................ 77

Setting the motion sensors .......................... 81

Setting alarm operation and display ............. 84

Canceling alarms ......................................... 85

4 GENERAL SET ............................................ 86

General settings ........................................... 86

Setting data display ...................................... 86

Setting display for video loss ........................ 87

Setting the buzzer ........................................ 88

Setting the security lock ............................... 89

Setting and initializing the hard disk ............. 92

Expanding the hard disk capacity ................ 93

Network settings ........................................... 93

Setting RS-485 ............................................. 96

Setting camera control ................................. 97

5 SCREEN SET ............................................ 100

Setting quad, multi 9 and 16 display .......... 100

Setting the period and monitors for

automatic screen selection ......................... 102

Setting masks ............................................. 104

Setting the color level ................................. 105

6 POWER LOSS/USED TIME ...................... 107

7 INITIALIZATION LOG ............................... 108

8 COPY MENU SETTINGS .......................... 109

Saving menu settings on a

CompactFlash card .................................... 109

Loading settings from a

CompactFlash card .................................... 110

1 INTERFACE SPECIFICATIONS ............... 111

RS-485 specifications ................................ 111

SANYO protocol command table ............... 112

2 SPECIFICATIONS ..................................... 113

Specifications ............................................. 113

Dimensions ................................................ 114

Table of recording rate and times .............. 115

Table of recording rate settings ................. 117

Table of pre-alarm recording times ............ 118

Terminal board specifications .................... 119

3 MENU SETTING SEQUENCE ................... 121

INDEX .............................................................. 123

SETTINGS

OTHER

e00_l8hbg_xe_7.book Page 4 Friday, November 5, 2004 10:21 AM

English 5

1 BEFORE USE

Notes on handling the internal HDD

This digital video recorder uses an internal hard disk drive

(HDD).

Be sure to observe the following points carefully when

operating, setting-up, or servicing the digital video

recorder.

 Do not subject the digital video recorder to

sudden impact or vibration.

If the digital video recorder is subjected to sudden impact

or vibration, it may damage the HDD or cause corruption of

the data stored within it.

z Do not move the digital video recorder while the power

is turned on. Always ensure that the power is turned off

before removing the digital video recorder from or

placing it in a rack.

z When transporting the digital video recorder, pack it

securely using the specified materials. In addition,

choose a method of transportation that minimizes

vibration.

z When placing the digital video recorder on the floor or

another similar surface, attach the specified pads to its

base and place it down gently.

 Do not move the digital video recorder for 30

seconds after turning off the power.

After the power is turned off, the disk inside the HDD will

continue to spin for a brief period due to inertia, and the

heads will be in an unstable condition.

During this period, the digital video recorder is even more

susceptible to damage from sudden impact and vibration

than when it is turned on. Make sure that the digital video

recorder is not subjected to even gentle vibration for at

least 30 seconds after turning off the power.

 Do not operate the digital video recorder when

condensation has formed on it.

If the digital video recorder is operated in this type of

condition, there is a possibility that it will be permanently

damaged.

If the temperature around the digital video recorder

changes suddenly, wait for it to stabilize before operating

the digital video recorder.

 Notes on replacing the HDD

Be sure to follow the correct procedure when replacing the

HDD.

z HDDs that have been removed from their packing may

not operate correctly if they are subjected to sudden

impact or vibration. It is recommended that you place

the HDD on a soft, level surface with the printed circuit

board facing upward after it has been unpacked.

z Take care to avoid subjecting the HDD to sudden

impact or vibration when removing and tightening

screws as part of the HDD replacement procedure.

Tighten all screws securely to ensure that they do not

loosen.

z The HDD is sensitive to static electricity; accordingly,

you should take the appropriate precautions to prevent

the buildup of static charges.

 Handling a detached HDD unit

If transporting or storing the HDD unit in a detached condition,

be sure to first of all pack it using the specified materials.

In addition, choose a method of transportation that

minimizes vibration.

Notes on installation locations

The hard disk is sensitive to dust, sudden impact, and

vibration; furthermore, it should not be used near magnetic

objects. The following precautions should be observed in

order to prevent the loss of recorded data:

z Do not subject the digital video recorder to sudden

impact.

z Do not use the digital video recorder on a vibrating or

unstable surface.

z Do not disconnect the power plug from the wall outlet

during recording or playback.

z

Do not use the digital video recorder in areas with extreme

temperature changes (i.e., 10ºC or more per hour).

z Condensation may occur if the digital video recorder is

moved to an area with a significantly different

temperature or high humidity. If the digital video

recorder is used while condensation is present inside it,

operating problems may occur.

z Do not install the digital video recorder inside motor

vehicles, trains, or other areas under constant vibration.

z The digital video recorder has ventilation holes on its

left, rear, and bottom panels. Ensure that these holes

are not blocked after installation.

z Do not use the digital video recorder in a bookshelf,

box, or any other area with poor ventilation.

z This digital video recorder is designed for use in a

horizontal orientation, and vertical setup may result in

malfunction.

z When installing the digital video recorder in a rack,

ensure that a gap of at least 5 cm is provided at the top

and bottom.

e00_l8hbg_xe_7.book Page 5 Friday, November 5, 2004 10:21 AM

BEFORE USE1

6 English

INTRODUCTION

The hard disk and cooling fan are

consumable components.

If used in an ambient temperature of 25ºC, the hard disk

should generally be replaced after 2 years; and the cooling

fan after 3 years. These figures are intended as a general

guideline only and should not be taken as a guarantee of

component performance.

The POWER indicator will flash if a problem occurs with

the hard disk or fan. (JP.7)

Important recordings

z Always perform test recording in advance to confirm

whether the digital video recorder’s playback is normal.

z Note that Sanyo will accept no responsibility for losses

occurring as a result of recording or playback problems

caused by malfunction of this digital video recorder or

any connected devices.

z As a precaution against malfunction or accidents, it is

advisable to periodically back up important recordings

or to perform mirroring.

Protection of the hard disk

The hard disk is checked automatically when the power is

turned on. If an abnormality is detected, the POWER

indicator will begin to flash or an error message will be

displayed. If you need initialize the hard disk or to save

images stored on it, contact the dealer from whom you

purchased this digital video recorder.

Backup battery

The digital video recorder comes with a built-in lithium

battery. If power is supplied continuously for at least 48

hours after setting the date and time, the clock will

continue to operate normally for up to 30 days without a

supply of power.

When disposing of this digital video recorder, contact the

dealer from whom it was purchased for information on how

to dispose of the lithium battery.

e00_l8hbg_xe_7.book Page 6 Friday, November 5, 2004 10:21 AM

English 7

2 NAMES AND FUNCTIONS OF PARTS

Front panel

1. POWER indicator

The POWER indicator will light up when the power is

turned on.

If the internal HDD or fan begins to malfunction, this

indicator will be flashed.

2. FULL indicator (JP.68)

The FULL indicator will begin to flash when the amount of

available memory in the hard disk’s normal recording area

drops to the percentage specified using menu settings.

In addition, recording will stop automatically when no more

memory is available, and the FULL indicator will switch to

a permanently lit condition.

This indicator can then be turned off by performing “AREA

FULL RESET” using menu settings.

3. ALARM FULL indicator (JP.68)

The ALARM FULL indicator will begin to flash when the

amount of available memory in the hard disk’s alarm

recording area drops to the percentage specified using

menu settings.

In addition, recording will stop automatically when no more

memory is available, and the ALARM FULL indicator will

switch to a permanently lit condition.

This indicator can then be turned off by performing “AREA

FULL RESET” using menu settings.

4. LOCK indicator (JP.91)

The LOCK indicator lights up when operation has been

locked using <SECURITY LOCK SET>.

An alarm will be sounded if a button is pressed in this

condition. In addition, a password entry screen will be

displayed on the monitor at this time.

If the correct administrator password is entered, the lock

condition will be cancelled and the LOCK indicator will turn

off.

5. ALARM indicator

The ALARM indicator flashes during alarm recording, and

it is lit up during pre-alarm recording.

6. [CAMERA SELECT] buttons and indicators

When one or more cameras have been connected to the

VIDEO IN terminals on the digital video recorder’s rear

panel and the appropriate [CAMERA SELECT] button is

pressed, the corresponding indicator lights up and the

video feed from that camera is displayed on-screen.

z During quad, multi 9 or 16 screen display:

The indicators corresponding to the cameras being

displayed on the monitor are lit up.

z If video is lost:

The indicator starts to flash.

z If an alarm occurs:

The indicator for the corresponding camera starts to flash.

7. [FUNC.] button and indicator (JP.99)

Switch to normal mode or camera control mode.

Press button for camera control mode and indicator will

light. Press button again to return to normal mode.

Indicator turns off.

8. [QUAD] button and indicator (JP.19)

The [QUAD] button is used to display video in quad

screens, and the indicator will light up when this type of

display is being presented.

The QUAD indicator will turn off when a different screen

display mode is adopted.

9. [MULTI] button and indicator (JP.20)

The [MULTI] button is used to display video in multi 9 or 16

screens, and the indicator will light up when this type of

display is being presented.

The MULTI indicator will turn off when a different screen

display mode is adopted.

The DSR-3709P can only display video in nine screens.

10. [MON2] button and indicator (JP.21)

If the [MON2] button is pressed while a monitor is

connected to the MON2 output terminal on the rear panel,

it will be possible to change the monitor 2 output video.

The [CAMERA SELECT] and [SEQUENCE] buttons can

be used, and the indicator will be lit up during the setting

procedure.

MENU

SEARCH

678123

45

14 15

1691011

12 13

MENU

EXIT/OSD

ZOOM

SEQUENCE

COPY

SHUTTLE HOLD

TIMER

ALARM

PLAY/STOP

ENTER AF

IRIS

FOCUS

STILL

REC/STOP

POWER FULL ALARM FULL LOCK ALARM

MULTI

FUNC.

TOUR

SEQUENCE

AUTO PAN

AUDIO

VIDEO

OUT

USB

PLUSMON 2

QUAD

PRESET

JOG

SHUTTLE

C

L

E

A

R

E

N

T

E

R

PAN

ZOOM/I/FO

CARD

RESET

EJECT

MENU

DSR-3716P

1

2345

6

8 7

10 11

12 13 14

1615 17

24

18

21

22 23 20

19

25

26

27

28

29

9

e00_l8hbg_xe_7.book Page 7 Friday, November 5, 2004 10:21 AM

NAMES AND FUNCTIONS OF PARTS2

8 English

INTRODUCTION

11. [PLUS] button and indicator (JP.20)

The [PLUS] button is used to enlarge video from a single

camera to quad screen size during multi 9 or multi 16

screen display.

For DSR-3709P, this operation is available only when in

multi 9 screen display.

12. [MENU] button and indicator

The [MENU] button is used to display the menu screens

(i.e., setting screens), and the indicator lights up while any

of these screens is being displayed.

13. [EXIT/OSD] button and indicator

z EXIT

The [EXIT/OSD] button is used to exit the main menu or a

sub-menu. When a menu is displayed, the indicator turns

off; when the menu is closed and the normal display is

restored, the indicator lights up.

z OSD (JP.16)

Each time the [EXIT/OSD] button is pressed while the

digital video recorder is recording, playing, or stopped, the

operating display location moves in the order of top of

screen, bottom of screen, to hidden; furthermore, the

indicator lights up when this information is being displayed.

14. [PLAY/STOP] button and indicator (JP.26)

When the [PLAY/STOP] button is pressed, a recording

from the normal recording area or alarm recording area is

played and the indicator lights up. When pressed during

playback, this button stops the digital video recorder.

15. [ZOOM] button and indicator (JP.19, 27)

When the [ZOOM] button is pressed during monitoring or

playback on a full screen, a portion of the playback video is

magnified and the indicator flashes.

16. [SEARCH] button and indicator (JP.31)

When the [SEARCH] button is pressed while the digital

video recorder is recording or stopped, the search menu is

displayed and the indicator lights up. The search menu

can be closed by pressing this button once again.

17. [STILL] button and indicator (JP.28)

When the [STILL] button is pressed during playback, the

current frame is displayed as a still image and the indicator

lights up. Playback can be resumed by pressing this button

once again.

18. [SEQUENCE] button and indicator (JP.21)

The [SEQUENCE] button can be pressed during

monitoring to automatically switch between screen display.

When pressed, the indicator begins flashing and the

display is changed automatically. The lighting condition of

CAMERA SELECT indicators also changes in response to

the screen display.

19. [COPY] button and indicator (JP.39)

The [COPY] button is used to copy recorded video to the

hard disk’s archive area, to a CompactFlash card, CD-R/

RW or to a Microdrive.

The indicator lights up during the copy process.

20. [SHUTTLE HOLD] button and indicator (JP.26)

The [SHUTTLE HOLD] button is used to lock shuttle dial

operation for a constant speed of playback or slow playback.

The indicator lights up while the shuttle dial is locked.

When a password has been set, furthermore, this button

can be pressed for at least three seconds to activate the

security lock.

21. [REC/STOP] button and indicator (JP.23)

The [REC/STOP] button is pressed to start normal

recording, and the indicator lights up during this process.

Furthermore, pressing this button for at least three

seconds stops recording and turns off the indicator.

SEARCH

6 7 8 9123

45

MENU

EXIT/OSD

ZOOM

SEQUENCE

COPY

SHUTTLE HOLD

TIMER

ALARM

PLAY/STOP

ENTER AF

IRIS

FOCUS

STILL

REC/STOP

POWER FULL ALARM FULL LOCK ALARM

MULTI

FUNC.

TOUR

SEQUENCE

AUTO PAN

AUDIO

VIDEO

OUT

USB

PLUSMON 2

QUAD

PRESET

JOG

SHUTTLE

C

L

E

A

R

E

N

T

E

R

PAN

ZOOM/I/FO

CARDCARD

MENU

RESET

EJECT

CARD

MENU

RESET

EJECT

DSR-3709P

1

2345

6

8 7

10 11

12 13 14

1615 17

24

18

21 22 23 20

19

25

26

9

27

28

29

e00_l8hbg_xe_7.book Page 8 Friday, November 5, 2004 10:21 AM

NAMES AND FUNCTIONS OF PARTS2

English 9

22. [TIMER] button and indicator (JP.23)

If the [TIMER] button is pressed while the recording is

stopped, timer recording standby mode is adopted and

recording will then start automatically at the set time. The

indicator will be lit up while in timer recording standby

mode or timer recording.

If the button is pressed during timer recording, this process

is stopped and the indicator turns off. Furthermore, if the

[TIMER] button is pressed when in timer recording standby

mode, indicator is turned off and timer recording is

cancelled.

23. [ALARM] buttons (JP.31)

When an [ALARM] button is pressed during playback or

still, the digital video recorder skips to the next earlier or

next later alarm.

24. Jog dial (inside) and shuttle dial (outside)

z During playback:

Use the jog dial to change the playback speed.

Use the shuttle dial to perform fast-forward or fast-

reverse playback.

z During menu display:

Use the jog dial to move the cursor and to change

setting values. Use the shuttle dial to confirm settings.

25. CompactFlash card slot (JP.41)

This slot is used to house a CompactFlash card or Microdrive.

26. [MENU RESET] button (JP.48)

The [MENU RESET] button is used to default menu

settings.

When setting motion sensors, furthermore, all sensors on

the same line as the cursor can be turned on

simultaneously by pressing this button.

27. Audio output terminal

Audio output is the same as that of the rear panel AUDIO

OUT terminal.

28. Video output terminal

This terminal outputs the same video as that of the MAIN

MONITOR output terminal on the rear panel.

29. USB terminal (JP.45)

This terminal connects to a recordable CD-R/RW drive.

z The USB terminal is for the use of the recommended

Sanyo CD-R/RW drive (sold separately). Non-

recommended peripherals cannot be connected.

z For recommended recordable drives, check the Sanyo

homepage or ask at your local Sanyo dealer.

Sanyo website URL:

http://www.sanyosecurity.com

MENU

SEARCH

678123

45

14 15

1691011

12 13

MENU

EXIT/OSD

ZOOM

SEQUENCE

COPY

SHUTTLE HOLD

TIMER

ALARM

PLAY/STOP

ENTER AF

IRIS

FOCUS

STILL

REC/STOP

POWER FULL ALARM FULL LOCK ALARM

MULTI

FUNC.

TOUR

SEQUENCE

AUTO PAN

AUDIO

VIDEO

OUT

USB

PLUSMON 2

QUAD

PRESET

JOG

SHUTTLE

C

L

E

A

R

E

N

T

E

R

PAN

ZOOM/I/FO

CARD

RESET

EJECT

MENU

DSR-3716P

1

2345

6

8 7

10 11

12 13 14

1615 17

24

18

21

22 23 20

19

25

26

27

28

29

9

e00_l8hbg_xe_7.book Page 9 Friday, November 5, 2004 10:21 AM

NAMES AND FUNCTIONS OF PARTS2

10 English

INTRODUCTION

Rear panel

1. VIDEO IN terminals

The DSR-3709P has nine VIDEO IN terminals.

2. VIDEO OUT terminals

The DSR-3709P has nine VIDEO OUT terminals.

3. [ALL RESET] button

When the [ALL RESET] button is pressed, the digital video

recorder is reset and the time is returned to its default

setting.

4. AUDIO IN terminal

5. AUDIO OUT terminal

6. MIC IN terminal

7. MAIN MONITOR output terminal

8. MON2 output terminal

9. USB terminal

This terminal connects to a recordable CD-R/RW drive.

10. LAN terminal (10 Base-T or 100 Base-TX)

11. RS-485 termination switch

12. RS-485 terminal (A)

13. RS-485 terminal (B)

14. ALARM IN terminals

These terminals are used to activate alarm recording in

response to operation of an alarm switch on a connected

device.

The DSR-3709P has nine ALARM IN terminals.

15. SENSOR ALARM OUT terminals

The terminals are used when motion sensors have been

set (JP.81) to output an alarm signal to a connected

device upon detection of motion.

The DSR-3709P has nine SENSOR ALARM OUT terminals.

16. CONTROL terminals

17. Power socket (AC IN)

Insert the supplied power cable securely into this socket.

18. Power cord holder

Secure the power cord to the holder

using the cord tie (accessory) as

shown in the illustration.

USB

LAN

TERMINATE

RS-485

OFF ON

A RS-485 B

ALARM IN

AC IN

SENSOR

ALARM OUT

DO NOT CONNECT TO PHONE LINE

C

LOCK

IN

C

LOCK OUT

ALARM OUT

ALARM RESET

ALARM FU

LL

NO

N RE

C OUT

WARNING OUT

FULL

SERIES OUT

EXIT TIMER IN

SERIES IN

REMOTE

CONTROL

C

123456789

10 11 12 13 14 15 16

C

123456789

10 11 12 13 14 15 16

CR1 R2

1

IN

OUT

ALL

RESET

AUDIO

MONITOR OUT

MON2

MIC IN

IN OUT

2 3 4 5 6 7 8 9 10 11 12 13 14 15

16

MAIN

DSR-3716P

(The number of terminals for the DSR-3709P may differ. For more details, see below.)

14

17

18

169 1087654

1

2

13

11

12

3 15

Pin Signal

C Ground

ALARM IN 1 to 16 Alarm input No. 1 through No. 16

Pin Signal

CGround

SENSOR ALARM OUT

1 to 16

Output of an alarm signal for Camera

No. 1 through No. 16

Pin Signal

C Ground

REMOTE R1 Remote input 1

REMOTE R2 Remote input 2

CLOCK SET IN

Input of a clock setting signal from an

external device

CLOCK SET OUT

Output of a clock setting signal to an

external device

ALARM OUT Total alarm output

ALARM RESET Alarm reset input

WARNING OUT Output of an HDD malfunction error

FULL

Capacity warning output for normal

recording area space

ALARM FULL

Capacity warning output for alarm recording

area space

SERIES IN

Signal input from an analog series

connection

SERIES OUT Signal output to an analog series connection

EXT TIMER IN Signal input from an external timer

NON REC OUT Non-recording output

C Ground

e00_l8hbg_xe_7.book Page 10 Friday, November 5, 2004 10:21 AM

English 11

3 INSTALLATION AND CONNECTIONS

This section describes how to connect the digital video recorder to video cameras and other devices. Be sure to read the

instruction manuals for each connected device.

z Improper connections can result in malfunction or the

emission of smoke.

z A separate power supply is required for operation of

each camera.

The following diagram shows the connections for cameras, monitors, a microphone, and a PC.

The RS-485 terminals are used to connect a system

controller (sold separately) to the digital video recorder.

After connecting the system controller, you will need to

carry out the settings that are given in the <RS-485 SET>

menu. (JP.96)

Pin locations

z Do not connect to phone line.

A: Non-inverting driver output/receiver input

B: lnverting driver output/receiver input

Basic connections

USB

LAN

TERMINATE

RS-485

OFF ON

A RS-485 B

ALARM IN

AC IN

SENSOR

ALARM OUT

DO NOT CONNECT TO PHONE LINE

C

CLOC

K

I

N

CLOC

K

OU

T

ALARM OUT

ALARM

RE

S

ET

ALARM

FULL

NO

N

REC

O

U

T

WARNING OU

T

FULL

SERIES OUT

E

XIT TIMER

I

N

SERIES

IN

REMOTE

CONTROL

C

123456789

10 11 12 13 14 15 16

C

123456789

10 11 12 13 14 15 16

CR1 R2

1

IN

OUT

ALL

RESET

AUDIO

MONITOR OUT

MON2

MIC IN

IN OUT

2 3 4 5 6 7 8 9 10 11 12 13 14 15

16

MAIN

0201

0403

Video input

terminal

PC

Monitor

(sold separately)

Video input

terminal

Monitor 2

(sold separately)

120 V-240 V AC

(50/60 Hz)

* If the monitor 2 (MON2) is not synchronized

with the connected cameras, vertical

picture instability may occur upon the

switching of camera video.

Camera

(sold separately)

(1-16)

Microphone

(sold separately)

System controller (sold separately)

VSP-8000/9000

The RS-485 connector is

connected to A or B according

to the type of cable.

DSR-3716P

The DSR-3709P can be connected to nine cameras.

Connecting RS-485 terminals

16

Pin number Connector A signal Connector B signal

1 Not used Not used

2 Not used Not used

3A B

4B A

5 Not used Not used

6 Not used Not used

e00_l8hbg_xe_7.book Page 11 Friday, November 5, 2004 10:21 AM

INSTALLATION AND CONNECTIONS3

12 English

INTRODUCTION

Connection

The digital video recorder supports both straight type and

crossed type connection cables.

When using a straight type connection cable, connect the

RS-485 connector’s pin A to the pin A socket, or pin B to

the pin B socket.

When using a crossed type connection cable, connect the

RS-485 connector’s pin A to the pin B socket, or pin B to

the pin A socket.

Cable types

Straight type:

Crossed type:

When connecting multiple devices, you must make

termination settings on both end devices.

z Set the RS-485 termination switch of both end devices

to ON.

z Be sure to set the RS-485 termination switches of all

devices in between (devices other than the first and last

devices) to OFF.

z If you don’t make the correct termination settings, the

incorrect data will be transmitted to each device.

Example

RS485

DO NOT CONNECT TO PHONE LINE

BA

To other

connector A

To other

connector A

Straight type cable Crossed type cable

1

2

3

4

5

6

1

2

3

4

5

6

Not used

1

2

3

4

5

6

1

2

3

4

5

6

Not used

RS-485 termination switch settings

ON

OFF ON

OFF

ON

OFF

System controller

Termination

switch

Digital video recorder

RS-485

termination

switch

Termination

switch

Time-lapse VCR

e00_l8hbg_xe_7.book Page 12 Friday, November 5, 2004 10:21 AM

INSTALLATION AND CONNECTIONS3

English 13

Turn off all devices and use a coaxial cable to connect the

devices.

1 Connect cameras to the VIDEO IN

terminals.

2 Set the protocols and address in the

<CAMERA CONTROL SET> screen.

(JP.97)

3 Operate the dome cameras with the

front panel buttons. (JP.99)

An amplifier is connected when using a microphone or

external speakers with the digital video recorder.

z Audio input from the AUDIO IN terminal and the MIC IN

terminal cannot be performed simultaneously. If both

terminals have devices connected, the MIC IN terminal

is used.

When using external alarms (i.e., intruder sensors and the

like), external switches are to be connected to the ALARM

IN terminals.

The DSR-3709P can be used between 1 and 9.

Connecting SANYO protocol devices

(Dome Cameras)

Camera

Connecting an amplifier

Connecting ALARM IN terminals

AUDIO

IN OUT

IN

OUT

Audio input

Audio

output

Amp

(sold separately)

* Wrap the cable

once around the

core clamp

before attaching

it.

*

1

16

C

123456789

10 11 12 13 14 15 16

Connecting ALARM IN

terminals to external

switches

e00_l8hbg_xe_7.book Page 13 Friday, November 5, 2004 10:21 AM

INSTALLATION AND CONNECTIONS3

14 English

INTRODUCTION

The SENSOR ALARM OUT terminals are used to relay

alarm signals whenever one of the digital video recorder’s

motion sensors is triggered. Normally in an open condition,

a terminal adopts low condition when a sensor for the

corresponding camera number has been triggered.

The connections for a remote control circuit are shown

below. This digital video recorder can be remotely controlled

when a remote-control circuit similar to that shown here is

connected to the remote-input control terminals.

z Use a resistance of 1/10 ohms or more and with a D

ranking (Precision within ±0.5%).

z The remote control cable should be no more than 5 m

long.

* The DSR-3709P can operate up to nine cameras (*).

1 When you have finished making all the

other connections, make sure the

voltage is 120 V-240 V AC and insert the

power plug into the wall outlet.

There is no power switch. The display indicators flash, and after

a few moments, the monitor screen displays the camera image.

z When turning the power on for the first time

“PLEASE SET THE CLOCK” is displayed on the monitor

screen. Follow the procedures on P.17 to set the clock.

z If the clock is already set

The operation display area is displayed.

z If the POWER indicator starts flashing;

If a problem occurs during use, the POWER indicator

will begin to flash and an explanation will be displayed.

In these cases, contact a Sanyo service center.

z The power cord’s ground terminal is not provided for

enhanced safety; rather, it can be used to reduce the

level of interference when the digital video recorder is

connected to analog devices.

If a large amount of noise is generated when the digital

video recorder is connected to analog devices, connect

this terminal to the building’s earth.

Connecting SENSOR ALARM OUT

terminals

Connecting CONTROL terminals

1

K

Rating for each terminal

z Maximum current: 25 mA

z Maximum voltage: 25 V

R1C R2

SW 1

SW 2

SW 3

SW 4

SW 5

SW 6

SW 7

SW 8

SW 9

SW 10

SW 11

SW 12

SW 13

SW 14

SW 15

SW 16

SW 17

SW 18

SW 19

SW 20

SW 21

SW 22

SW 23

SW 24

SW 25

SW 26

SW 27

SW 28

SW 29

SW 30

SW 31

SW 32

R1 R2

: Camera 1*: INDEX +

: Camera 2*: INDEX -

: Camera 3*:

AUTO FOCUS

: Camera 4*: SEQUENCE

: Camera 5*: MON2

: Camera 6*: PLUS

: Camera 7*: QUAD

: Camera 8*: MULTI

: Camera 9*:

MENU RESET

: Camera 10:

: Camera 11: PAN left

: Camera 12: PAN right

: Camera 13: TILT down

: Camera 14: TILT up

: Camera 15: ZOOM wide

: Camera 16: ZOOM tele

: REC/STOP

: PLAY/STOP

: STILL

: SEARCH

:

SHIFT (Doubles with R1)

: PLAY

: REC

: MENU

: EXIT/OSD

: +

: -

:

→

:

←

: ZOOM

: COPY

: TIMER

(When combined

with R2 Shift key)

(When operated

independently)

Connecting the power cord

POWER

indicator status

Meaning

Four flashes per

second

There is a problem with the hard disk. The

hard disk must be replaced or initialized.

Contact a Sanyo service center to recover

recorded images.

One flash per

second

There is a problem with the fan.

120 V-240 V AC

(50/60 Hz)

02

0

01-01-04 00:00:00 REC REPEAT EN A ALARM 0000

Operation

display area

e00_l8hbg_xe_7.book Page 14 Friday, November 5, 2004 10:21 AM

English 15

1 PREPARING FOR USE

Whenever the power is turned on, the operation display

area will be shown at the top of the monitor screen. This

area indicates the date, time, picture quality, and other

information needed for operation.

(1) Date display (JP.17)

“01-01-04” (day-month-year) is displayed when you

turn the power on for the first time. Be sure to specify

the correct date using menu settings.

(2) Time display (JP.17)

“00:00:00” is displayed when you turn the power on for

the first time. The digital video recorder uses the date

and time to manage recording and playback points.

Accordingly, if the time has not been set correctly, you

will not be able to effectively search for video data.

Make sure to specify the time using menu settings.

Recording will not be possible until a setting has been

made.

(3) Operating symbol display

Displays the current operation (such as recording or

playback).

z During simultaneous recording and playback, the

display indicates playback ( ).

(4) Remaining memory in recording area (JP.67)

Displays the remaining area memory as a percentage

when overwriting in the normal recording area or the

alarm recording area is forbidden. If overwriting has

been permitted, “REPEAT” is displayed.

(5) Picture quality display (JP.71)

Displays the quality of the video that can be recorded

on the hard disk. Set to “EN” (Enhanced) by default.

(6) Audio recording display

“A” is displayed when audio is being recorded or

played back.

(7) Alarm display and alarm count display (JP.77)

When you set an alarm using the “ALARM REC

MODE SET” menu item, the alarm display area

presents the following information.

z When alarm recording is set;

“ALARM” is displayed.

“ALARM” is flashed during alarm recording.

z When pre-alarm recording is set;

“PRE” is displayed.

When an alarm occurs, “PRE” disappears,

“ALARM” is displayed, and the number of alarms is

shown. The total number is indicated in the alarm

display.

z When performing playback from the archive

area;

“ARCHIV” is displayed.

z When an external alarm signal is activated;

“EA” is flashed to the left of the camera number.

z When a motion sensor alarm signal is

activated;

“SA” is flashed to the left of the camera number.

z When an external alarm signal and motion

sensor signal are activated;

“ES” flashes to the left of the camera number.

(8) Camera title display

The camera number or camera title is displayed. In

addition, when an alarm occurs, the camera number

and alarm “EA”, “SA” or “ES” are displayed along with

the camera title.

z During video loss;

The display alternates between showing the

camera title and “VIDEO LOSS”. “VIDEO LOSS”

flashes when the operating display is hidden.

(JP.16)

z During no video signal;

“NO VIDEO” is displayed in place of the camera

title.

z Although operations such as playback, copying, and

data transfer are possible while recording, this unit

gives priority to recording, and other operations may be

delayed as a result.

Operation display area

REC: Recording : Fast-forward playback

EXT: External timer recording : Fast-rewind playback

: Playback : Slow playback

: Reverse playback : Reverse slow playback

: Still

02

0

01-01-04 00:00:00 REC REPEAT EN A ALARM 0000

02

(1) (2) (3) (4) (5) (6) (7)

(8)

BA Basic

NO Normal

EN Enhanced

FI Fine

SF Super Fine

e00_l8hbg_xe_7.book Page 15 Friday, November 5, 2004 10:21 AM

PREPARING FOR USE1

16 English

OPERATION

1 Press the [EXIT/OSD] button.

As the [EXIT/OSD] button is pressed, the operation display

area moves to a different location or is hidden.

Use the following procedure to set the language displayed

on the monitor.

[Settings] ( indicates default setting)

1 Press the [MENU] button.

The MENU indicator lights up and the <MAIN MENU> is

displayed.

2 Turn the shuttle dial clockwise.

The <INITIAL SET> screen is displayed.

3 Turn the shuttle dial clockwise.

The cursor moves to “ENGLISH”.

CARDCARD

MENU

RESET

EJECT

[MENU] button [EXIT/OSD] button

[REC/STOP] button

Shuttle dial

Jog dial

Changing the position of the

operation display area

Changing the language

Item Setting Description

LANGUAGE

ENGLISH Sets the language to English.

FRANCAIS Sets the language to French.

DEUTSCH Sets the language to German.

ESPAÑOL Sets the language to Spanish.

01 02

03 04

01-01-04 00:00:00 REC REPEAT EN A ALARM 0000

Operation

display area

Top (default)

Bottom

Hidden

1.INITIAL SET ->

2.RECORD SET ->

3.GENERAL SET ->

4.SCREEN SET ->

5.POWER LOSS/USED TIME ->

6.INITIALIZATION LOG ->

7.COPY MENU SETTINGS ->

MOVE:JOG SELECT:SHUTTLE

MENU

1.LANGUAGE/CLOCK SET ->

2.CAMERA DETECT ->

3.TITLE SET ->

4.HOLIDAY SET ->

5.TIME PERIOD SET ->

MOVE:JOG SELECT:SHUTTLE

ENGLISH

01-01-2004 THU 00:00:00

MODE : USE

WEEK MONTH TIME

ON LST-SUN 03 02:00

OFF LST-SUN 10 02:00

<EXT.CLOCK SET>

ADJUST. TIME 01:00

e00_l8hbg_xe_7.book Page 16 Friday, November 5, 2004 10:21 AM

PREPARING FOR USE1

English 17

4 Turn the shuttle dial clockwise, and

then turn the jog dial to select the

desired language.

The set item flashes.

5 When you have made a selection, turn

the shuttle dial clockwise.

The cursor moves to the date and time.

The language has now been set.

To return to the normal screen, press the [EXIT/OSD] button.

(Default: 01-01-2004 THU 00:00:00)

Be sure to set the correct date and time as these settings

are used during recording and searching.

Example: Setting 8:30 on 26 October 2004

1 Press the [MENU] button.

The MENU indicator lights up and the <MAIN MENU> is

displayed.

2 Turn the shuttle dial clockwise.

The <INITIAL SET> screen is displayed.

3 Turn the shuttle dial clockwise.

The <LANGUAGE/LANGUE/SPRACHE/IDIOMA> screen

is displayed.

4 Turn the jog dial to select the date and

time for <CLOCK SET> and turn the

shuttle dial clockwise.

“01” flashes (indicating the day).

5 Set “26” with the jog dial or numeric

keys and turn the shuttle dial clockwise.

“01” flashes (indicating the month).

6 Use the same procedure to set the

month (10), year (2004), hour (08), and

minute (30).

When you have set the minute, the cursor moves to

“MODE” under <SUMMER TIME SET>, and the clock

starts counting from 00 seconds.

z The week day is set automatically.

z The clock is stopped during date and time settings.

7 Press the [EXIT/OSD] button.

The setting procedure is ended and the display returns to

the normal screen.

Setting the time

<REGL.LANGUE>

FRANCAIS

<REGL.HORLOGE>

01-01-2004 JEU 00:00:00

<HEURE D

,

ETE>

MODE : MARCHE

SEMAINE MOIS HEURE

ON DER-DIM 03 02:00

OFF DER-DIM 10 02:00

<REGL.HORLOGE EXTERNE>

REGL.DE L

,

HEURE 01:00

EXIT/OSD

1.INITIAL SET ->

2.RECORD SET ->

3.GENERAL SET ->

4.SCREEN SET ->

5.POWER LOSS/USED TIME ->

6.INITIALIZATION LOG ->

7.COPY MENU SETTINGS ->

MOVE:JOG SELECT:SHUTTLE

MENU

1.LANGUAGE/CLOCK SET ->

2.CAMERA DETECT ->

3.TITLE SET ->

4.HOLIDAY SET ->

5.TIME PERIOD SET ->

MOVE:JOG SELECT:SHUTTLE

ENGLISH

01-01-2004 THU 00:00:00

MODE : USE

WEEK MONTH TIME

ON LST-SUN 03 02:00

OFF LST-SUN 10 02:00

<EXT.CLOCK SET>

ADJUST. TIME 01:00

<LANGUAGE/LANGUE/SPRACHE/IDIOMA> K

ENGLISH

01-01-2004 THU 00:00:00

MODE : USE

WEEK MONTH TIME

ON LST-SUN 03 02:00

OFF LST-SUN 10 02:00

<EXT.CLOCK SET>

ADJUST. TIME 01:00

26-01-2004 MON 00:00:00

EXIT/OSD

e00_l8hbg_xe_7.book Page 17 Friday, November 5, 2004 10:21 AM

PREPARING FOR USE1

18 English

OPERATION

Hard disk recording areas

When the digital video recorder is turned on, recording

areas are automatically setup within the internal hard disk

(with the default settings being normal recording area:

80%, alarm recording area: 19%, and archive area: 1%).

When the [REC/STOP] button is pressed, this digital video

recorder starts recording video data in the normal

recording area. When an alarm occurs, the corresponding

video data is recorded in the alarm recording area.

[A] Normal recording area

[B] Alarm recording area

[C] Archive area

z If the memory allocations for the various hard disk

recording areas are changed during a recording

process, all stored recordings will be deleted and the

hard disk will be initialized; accordingly, special care

should be taken. For more details, refer to P.65.

z In the case of certain hard disks, error may be present

in the total hard disk capacity as displayed on menu

screens.

The internal hard disk

Recording

mode

Recording method

Normal

recording

Manual

When monitoring, recording is per-

formed in response to pressing of the

[REC/STOP] button.

Timer

recording

Automatic

Recording is carried out in accordance

with timer settings.

Recording

mode

Recording method

Alarm

recording

Automatic

Recording is carried out when alarm

recording is set to “ENABLED”. Specifi-

cally, alarm images are recorded in the

alarm recording area in response

either to operation of a switch that has

been connected to an alarm input ter-

minal or to detection of an intruder or

the like using motion sensors.

Pre-alarm

recording

Automatic

When pre-alarm recording is set to

“ON”, it will be possible to record video

from before the occurrence of an alarm

based on the corresponding settings.

TOTAL CAPACITY : 82GB

NORMAL RECORDING AREA : 80 %

AREA FULL RESET ->

ALARM RECORDING AREA : 19 %

AREA FULL RESET ->

ARCHIVE AREA : 1 %

AREA FULL RESET ->

CAUTION : WHEN THE AREA SETTING IS CHANGED,

THE WHOLE AREA WILL BE INITIALIZED !

[A]

[B]

[C]

C

A

B

1%

80%

1%

80%

19%

Alarm

recording

area

Archive area

Hard Disk Recording Areas

Normal recording

area

Recording

mode

Recording method

Copy Manual

This area is used to store important

video data copied from the normal

recording area and/or alarm recording

area. By making changes to the normal

recording area and the alarm recording

area, this area can be extended to up

to 10 GB in size (i.e., 12% when using

a 80 GB hard disk).

e00_l8hbg_xe_7.book Page 18 Friday, November 5, 2004 10:21 AM

English 19

2 VIEWING VIDEO FROM A CAMERA

Example: Selecting Camera 2

1 Press the No. 2 [CAMERA SELECT]

button.

The No. 2 CAMERA SELECT indicator lights up and video

from Camera 2 is displayed on a full screen.

Images can be enlarged while monitoring on a full screen.

Operations are the same as “Enlarging the playback

video”. See P.27 for more details.

Images from multiple connected cameras can be

displayed simultaneously.

1 Press the [QUAD] button.

The QUAD indicator lights up and video from four separate

cameras is displayed simultaneously.

Video from Camera No. 1 through Camera No. 4 is

displayed.

2 To view video from other cameras,

press the [QUAD] button again.

Each time this button is pressed, the four images on the

quad screen change, in order of cameras No. 1-4, 5-8, 9-

12 and 13-16.

On the DSR-3709P, the images change in order of

cameras No. 1-4, 5-8, 9-3, etc.

3 To return to full screen display, press

the [CAMERA SELECT] button.

[CAMERA SELECT] buttons

CARDCARD

MENU

RESET

EJECT

[MULTI] button

[SEQUENCE] button

[MON2] button

[QUAD] button

[PLUS] button

Viewing on a full screen

Viewing enlarged live images

02

Viewing on quad screens

QUAD

0201

0403

QUAD

0605

0807

e00_l8hbg_xe_7.book Page 19 Friday, November 5, 2004 10:21 AM

Page is loading ...

Optimus V-700DB2 User manual

This manual is also suitable for

Optimus V-700DB2 User manual

Other documents