Construction
Automotive
Industry
www.rehau.com
APPLIANCE GARAGE
TAmbouR dooR sysTEms
fAbRICATIoN ANd INsTALLATIoN INsTRuCTIoNs
4. Cut the top boards.
Cut length = Depth (If the board is shorter than the depth, use the
whole board; you will not need anything longer)
5. Cut the vertical boards.
Cut length = Interior height minus 1 1/2 in.
6. Cut the top track.
Cut length = Depth minus 1 15/16 in.
7. Cut the vertical track.
Cut length = Height minus 1 15/16 in.
8. Install the C6 counterbalance system on to the tambour slats.
The C6 counterbalance systems includes one hook, ve screws, two
wooden strips for E23 PVC Line, one rubber cord with pre-crimped
eyelet and two plastic pieces for the installation of Metallic Line.
1. Measure inside dimensions of the cabinet.
Height: in. (Countertop to the bottom of the cabinets)
Width: in. (Inside width)
Depth: in. (Back of the face board to the wall)
2. Cut tambour slats.
Corner unit cut length = Inside width minus 1 7/8 in.
Straight unit cut length = Inside width minus 3/8 in.
3. Cut the handle prole.
3.a. If assembling the E23 Polymer Line:
Cut length = Length of tambour slats
3.b. If assembling the Metallic Line:
Cut length = Slat width minus 1/8 in to allow space for
handle gliders.
Depth
Width
Height
Parts list
8.a Install wooden or plastic pieces into rsts slats beyond the
radius
8.b. If installing the E23 PVC Line:
8.b.1. Push wooden strips completely into the tambour
door slat (Y)
8.b.2. Create screw lead holes on the back of tambour
door approx. 20 mm from each outer edged.
8.b.3. Screw the pre-crimped eyelet on to the rubber cord
into one of the wood strips.
Note: Do not cut the cord
9. Install the tambour unit into cabinet
Note: For straight unit the support boards represent the inside of the
appliance garage.
9.a. Slide corner and one track piece together and fasten to the
top support board as shown. Repeat for the left side.
9.b. Fasten vertical support board to top support board.
Repeat for other side.
Y
8.c. If installing the Metallic Line:
8.c.1. Cut off screw hole of pre-crimped eyelet
8.c.2. Prepare the left piece with the pre-crimped eyelet.
Pay attention to the exact shape of the plastic piece.
8.c.3. Install left side.
Note: Do not cut the cord
www.rehau.com
rehau.mailbox@rehau.com
For updates to this publication, visit na.rehau.com/resourcecenter
The information contained herein is believed to be reliable, but no representations, guarantees or warranties of any kind are made as to its accuracy, suitability for particular applications or the results to be obtained therefrom. Before using, the
user will determine suitability of the information for user’s intended use and shall assume all risk and liability in connection therewith. To the extent permitted by law, REHAU EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES, INCLUDING BUT
NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE. © REHAU Incorporated 2009 Printed in USA
9.c. Fasten top track piece, corner and support boards inside
appliance garage making sure they are square to the face
frame. Be careful not to screw through the face frame.
9.d. Slide the tambour slats and handle into the already installed
top track pieces. Slide the tambour up and out of the way.
Fasten hook to the bottom of cabinet
Hook
100.723 04.2009
10. Attach the cord
Attached the cord to the hook. Adjust the length of the cord to prevent
slamming when closing. Excess cord can be trimmed.
9.e. Fasten the vertical piece of track to the vertical support
boards.
/
