ACDelco 10335582 User manual

10335582
ACDelco
Brand
ACDelco
Model
10335582
Type
User manual

ACDelco 10335582 is a key fob programming tool specifically designed for certain GM vehicles. With this device, you can program new key fobs or replace lost ones, allowing you to conveniently lock, unlock, and operate your vehicle's keyless entry system. The programming process is straightforward and can be completed in a matter of minutes by following the detailed instructions provided in the manual. Please refer to the instruction manual for a list of compatible vehicles and specific programming procedures.

ACDelco 10335582 is a key fob programming tool specifically designed for certain GM vehicles. With this device, you can program new key fobs or replace lost ones, allowing you to conveniently lock, unlock, and operate your vehicle's keyless entry system. The programming process is straightforward and can be completed in a matter of minutes by following the detailed instructions provided in the manual. Please refer to the instruction manual for a list of compatible vehicles and specific programming procedures.

INSTRUCTION SHEET
KEY FOB PROGRAMMING INSTRUCTIONS -
10335582
FOR AUTOMOBILES:
These vehicles can be programmed using the
instructions below:
• 2001 Oldsmobile Intrigue
• 2001-2003 Pontiac Grand Prix
These vehicles require the use of a professional scan
tool for programming (see your local GM dealer or
ACDelco Professional Service Center):
• 2001-2005 Buick Century
• 2001-2004 Buick Regal
• 2002 Oldsmobile Intrigue
2001 OLDSMOBILE INTRIGUE:
CAUTION: TEXT IMPORTANT: ALL TRANSMITTERS WHICH ARE TO BE RECOGNIZED BY THE
REMOTE CONTROL DOOR LOCK RECEIVER (RCDLR) MUST BE PROGRAMMED IN A
SINGLE PROGRAMMING SEQUENCE. IF THE SYSTEM IS PLACED IN PROGRAM MODE IT
WILL ERASE ALL PREVIOUSLY PROGRAMMED TRANSMITTERS UPON THE RECEIPT OF
THE PROGRAMMING SIGNAL FROM THE FIRST TRANSMITTER. UP TO FOUR TRANSMIT-
TERS CAN BE PROGRAMMED. TO PREVENT THE PROGRAMMING OF TRANSMITTERS TO
AN INCORRECT VEHICLE, DO NOT OPERATE OR PROGRAM THE TRANSMITTERS IN THE
VICINITY OF OTHER VEHICLES THAT ARE IN THE KEYLESS ENTRY PROGRAM MODE.
TRANSMITTER PROGRAMMING PROCEDURE
1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the ignition key from the ignition lock cylinder.
4. Press and hold the driver side door lock switch to the unlock position.
5. Insert the ignition key into the ignition lock cylinder and remove the
key. (Do not turn the ignition key in the lock cylinder.)
6. Repeat Step 5.
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the
ignition key in the lock cylinder.) Leave the ignition key in the igni-
tion lock cylinder.
8. Release the door lock switch. The body control module (BCM) will
sound three chimes in order to verify the Program Mode has been
activated.
9. Press the lock and unlock buttons on the keyless entry transmitter
simultaneously for approximately 15 seconds. The BCM will sound
three chimes in order to verify that the transmitter has been suc-
cessfully programmed.
10. Perform the previous step to program up to four transmitters.
11. Remove the ignition key in order to exit the Program Mode.
12. Verify the proper operation of each transmitter.
INSTRUCTION SHEET
2001 - 2003 PONTIAC GRAND PRIX:
CAUTION: TEXT IMPORTANT: ALL TRANSMITTERS WHICH ARE TO BE RECOGNIZED BY THE
REMOTE CONTROL DOOR LOCK RECEIVER (RCDLR) MUST BE PROGRAMMED IN A
SINGLE PROGRAMMING SEQUENCE. IF THE SYSTEM IS PLACED IN PROGRAM MODE IT
WILL ERASE ALL PREVIOUSLY PROGRAMMED TRANSMITTERS UPON THE RECEIPT OF
THE PROGRAMMING SIGNAL FROM THE FIRST TRANSMITTER. UP TO FOUR TRANSMIT-
TERS CAN BE PROGRAMMED. TO PREVENT THE PROGRAMMING OF TRANSMITTERS TO
AN INCORRECT VEHICLE, DO NOT OPERATE OR PROGRAM THE TRANSMITTERS IN THE
VICINITY OF OTHER VEHICLES THAT ARE IN THE KEYLESS ENTRY PROGRAM MODE.
1. Remove the ignition key from the ignition lock cylinder.
2. Close all of the doors.
3. Remove the MALL PGM fuse from the fuse block. (Refer to “Instru-
ment Panel Fuse Block” in your Owner’s Manual for the location of
your fuse block and the Fuse Usage Chart.)
4. Insert the ignition key into the ignition lock cylinder.
5. Turn the ignition to ACC.
6. Turn the ignition to OFF, and then back to ACC within 1 second.
7. Open and then close any vehicle door. The vehicle will chime in
order to confirm that the programming mode has been entered.
8. Press and hold the transmitter LOCK and UNLOCK buttons simul-
taneously for approximately 14 seconds.
CAUTION: TEXT IMPORTANT: AFTER APPROXIMATELY 7 SECONDS THE VEHICLE WILL CHIME
ONCE TO CONFIRM THAT SYNCHRONIZATION HAS BEEN COMPLETED. AFTER APPROXI-
MATELY 14 SECONDS THE VEHICLE WILL CHIME A SECOND TIME TO CONFIRM THAT THE
PROGRAMMING HAS BEEN COMPLETED.
9. Repeat the previous step in order to program each additional trans-
mitter.
10. Remove the ignition key from the ignition lock cylinder.
11. Install the MALL PGM fuse into the fuse block.
12. Operate the functions of each transmitter in order to verify correct
system operation.
  • Page 1 1
  • Page 2 2

ACDelco 10335582 User manual

10335582
ACDelco
Brand
ACDelco
Model
10335582
Type
User manual

ACDelco 10335582 is a key fob programming tool specifically designed for certain GM vehicles. With this device, you can program new key fobs or replace lost ones, allowing you to conveniently lock, unlock, and operate your vehicle's keyless entry system. The programming process is straightforward and can be completed in a matter of minutes by following the detailed instructions provided in the manual. Please refer to the instruction manual for a list of compatible vehicles and specific programming procedures.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents