BenQ MS510 User manual

Welcome

MW512

Digital Projector

User Manual

Table of contents2

Table of contents

Important safety

instructions ........................3

Introduction....................... 7

Projector features ................................. 7

Shipping contents................................. 8

Projector exterior view......................... 9

Controls and functions ...................... 10

Positioning your

projector........................... 14

Choosing a location............................ 14

Obtaining a preferred projected image

size....................................................... 15

Connection ...................... 18

Connecting a computer or monitor.. 19

Connecting Video source devices...... 20

Operation ......................... 24

Starting up the projector.................... 24

Adjusting the projected image ........... 25

Using the menus................................. 27

Securing the projector........................ 28

Switching input signal........................ 31

Magnifying and searching for details 32

Selecting the aspect ratio.................... 32

Optimizing the image......................... 34

Creating your own startup screen ..... 37

Setting the presentation timer ........... 38

Remote paging operations ................. 39

Hiding the image ................................ 39

Freezing the image.............................. 40

Utilizing FAQ function ...................... 40

Operating in a high altitude

environment........................................ 41

Adjusting the sound............................ 41

Adjusting the sound level ................... 41

Personalizing the projector menu

display.................................................. 42

Shutting down the projector .............. 42

Menu operation .................................. 43

Maintenance..................... 55

Care of the projector........................... 55

Lamp information............................... 56

Troubleshooting .............. 62

Specifications ................... 63

Dimensions.......................................... 64

Ceiling mount installation.................. 64

Timing chart ........................................65

Warranty and Copyright

information...................... 68

Regulation statements ..... 69

Important safety instructions 3

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information

technology equipment. However, to ensure safe use of this product, it is important that you

follow the instructions mentioned in this manual and marked on the product.

Safety Instructions

1. Please read this manual before you

operate your projector. Save it for

future reference.

2. Do not look straight at the projector

lens during operation. The intense

light beam may damage your eyes.

3. Refer servicing to qualified service

personnel.

4. Always open the lens shutter or

remove the lens cap when the

projector lamp is on.

5. In some countries, the line voltage is

NOT stable. This projector is designed

to operate safely within a mains

voltage between 100 to 240 volts AC,

but could fail if power cuts or surges

of ±10 volts occur. In areas where the

mains voltage may fluctuate or cut

out, it is recommended that you

connect your projector through a

power stabilizer, surge protector or

uninterruptible power supply (UPS).

6. Do not block the projection lens with

any objects when the projector is

under operation as this could cause

the objects to become heated and

deformed or even cause a fire. To

temporarily turn off the lamp, press

BLANK on the projector or remote

control.

Important safety instructions4

Safety Instructions (Continued)

7. The lamp becomes extremely hot

during operation. Allow the

projector to cool for approximately

45 minutes prior to removing the

lamp assembly for replacement.

8. Do not operate lamps beyond the

rated lamp life. Excessive operation

of lamps beyond the rated life could

cause them to break on rare

occasions.

9. Never replace the lamp assembly or

any electronic components unless

the projector is unplugged.

10. Do not place this product on an

unstable cart, stand, or table. The

product may fall, sustaining serious

damage.

11. Do not attempt to disassemble this

projector. There are dangerous high

voltages inside which may cause

death if you should come into

contact with live parts. The only

user serviceable part is the lamp

which has its own removable cover.

Under no circumstances should you

ever undo or remove any other

covers. Refer servicing only to

suitably qualified professional

service personnel.

12. When the projector is under

operation, you may sense some

heated air and odor from its

ventilation grill. It is a normal

phenomenon and not a product

defect.

Important safety instructions 5

Safety Instructions (Continued)

13. Do not place this projector in any of

the following environments.

- Space that is poorly ventilated or

confined. Allow at least 50 cm clearance

from walls and free flow of air around the

projector.

- Locations where temperatures may

become excessively high, such as the

inside of a car with all windows rolled up.

- Locations where excessive humidity, dust,

or cigarette smoke may contaminate

optical components, shortening the

projector's life span and darkening the

image.

- Locations near fire alarms

- Locations with an ambient temperature

above 40°C / 104°F

- Locations where the altitudes are higher

than 3000 m (10000 feet).

14. Do not block the ventilation holes.

- Do not place this projector on a blanket,

bedding or any other soft surface.

- Do not cover this projector with a cloth or

any other item.

- Do not place inflammables near the

projector.

If the ventilation holes are seriously

obstructed, overheating inside the

projector may result in a fire.

15. Always place the projector on a level,

horizontal surface during operation.

- Do not use if tilted at an angle of more

than 10 degrees left to right, nor at angle

of more than 15 degrees front to back.

Using the projector when it is not fully

horizontal may cause a malfunction of, or

damage to, the lamp.

3000 m

(10000 feet)

0 m

(0 feet)

Important safety instructions6

Safety Instructions (Continued)

16. Do not stand the projector on end

vertically. Doing so may cause the

projector to fall over, causing injury or

resulting in damage to the projector.

17. Do not step on the projector or place

any objects upon it. Besides probable

physical damage to the projector, doing

so may result in accidents and possible

injury.

18. Do not place liquids near or on the

projector. Liquids spilled into the

projector may cause it to fail. If the

projector does become wet, disconnect

it from the power supply's wall socket

and call BenQ to have the projector

serviced.

19. This product is capable of displaying

inverted images for ceiling mount

installation.

Use only BenQ's Ceiling Mount Kit for

mounting the projector and ensure it

is securely installed.

Introduction 7

Introduction

Projector features

The projector integrates high-performance optical engine projection and a user-friendly

design to deliver high reliability and ease of use.

The projector offers the following features.

• Wall color correction allowing projection on surfaces of several predefined colors

• Quick auto search speeding up the signal detecting process

• Selectable password protected function

• 3D color management allowing color adjustments to your liking

• Selectable quick cooling function makes the projector cool in a shorter time

• Presentation timer for better control of time during presentations

• One-key auto-adjustment to display the best picture quality

• Digital keystone correction to correct distorted images

• Adjustable color balance control for data/video display

• High brightness projection lamp

• Multi-language On-Screen Display (OSD) menus

• Switchable normal and economic modes to reduce the power consumption

• Component HDTV compatibility (YPbPr)

• Less than 1 W power consumption in standby mode

• Built-in speaker providing mixed mono audio when an audio input is connected

• HDMI compatibility

• The apparent brightness of the projected image will vary depending on the ambient

lighting conditions, selected input signal contrast/brightness settings, and is directly

proportional to projection distance.

• The lamp brightness will decline over time and may vary within the lamp manufacturers

specifications. This is normal and expected behavior.

Introduction8

Shipping contents

Carefully unpack and verify that you have all of the items shown below. If any of these items

are missing, please contact your place of purchase.

Standard accessories

The supplied accessories will be suitable for your region, and may differ from those

illustrated.

*The warranty card is only supplied in some specific regions. Please consult your dealer for

detailed information.

Optional accessories

Projector Power cord VGA cable

Quick start guide User manual CD Warranty card*

Pull the tab before using the remote

control.

Remote control with battery

1. Spare lamp kit

2. Ceiling mount kit

3. Soft carry case

4. RS232 cable

Introduction 9

Projector exterior view

1. External control panel

(See "Projector" on page 10 for

details.)

2. Lamp cover

3. Zoom ring

4. Focus ring

5. Lens cover

6. Vent (heated air exhaust)

7. Front IR remote sensor

8. Projection lens

9. Quick-release button

10. RGB (PC)/Component video

(YPbPr/ YCbCr) signal input jack

11. RGB signal output jack

12. S-Video input jack

13. HDMI input jack

14. USB input jack

15. RS-232 control port

16. Audio input jack

17. AC power cord inlet

18. Video input jack

19. Kensington anti-theft lock slot

20. Audio output jack

21. Ceiling mount holes

22. Rear adjuster foot

23. Speaker

24. Rear IR remote sensor

Front/upper side

8

7

1

2

5

3

46

9

Rear/lower side

12

10 11 13 15 16

18 2417 921 22

19 23

14

20

Introduction10

Controls and functions

Projector

6. Mode/Enter

Selects an available picture setup mode.

See "Selecting a picture mode" on page 34

for details.

Activates the selected On-Screen Display

(OSD) menu item. See "Using the menus"

on page 27 for details.

7. Source

Displays the source selection bar. See

"Switching input signal" on page 31 for

details.

8. Power/POWER indicator light

Toggles the projector between standby

mode and on.See "Starting up the

projector" on page 24 and "Shutting down

the projector" on page 42 for details.

Lights up or flashes when the projector is

under operation. See "Indicators" on page

61 for detail.

9. TEMPerature indicator light

Lights up red if the projector's

temperature becomes too high. See

"Indicators" on page 61 for details.

10. Right/Auto

When the On-Screen Display (OSD)

menu is activated, the #4, #5, and #10 keys

are used as directional arrows to select the

desired menu items and to make

adjustments. See "Using the menus" on

page 27 for details.

Automatically determines the best picture

timings for the displayed image. See

"Auto-adjusting the image" on page 25 for

details.

11. Menu/Exit

Turns on the On-Screen D is play (OSD)

menu. Goes back to previous OSD menu,

exits and saves menu settings.

1. Focus ring

Adjusts the focus of the projected image.

See "Fine-tuning the image size and clarity"

on page 26 for details.

2. Zoom ring

Adjusts the size of the image. See "Fine-

tuning the image size and clarity" on page

26 for details.

3. LAMP indicator light

Indicates the status of the lamp. Lights up

or flashes when the lamp has developed a

problem. See "Indicators" on page 61 for

details.

4. Keystone/Arrow keys ( / Up, /

Down)

Manually corrects distorted images

resulting from an angled projection. See

"Correcting keystone" on page 26 for

details.

5. Left/Blank

Used to hide the screen picture. See "Hiding

the image" on page 39 for details.

1

3

4

10

2

9

11

8

6

7

4

5

I

Introduction 11

Ceiling mounting the projector

We want you to have a pleasant experience using your BenQ projector, so we need to

bring this safety matter to your attention to prevent possible damage to person and

property.

If you intend to mount your projector on the ceiling, we strongly recommend that you

use a proper fitting BenQ projector ceiling mount kit and that you ensure it is securely

and safely installed.

If you use a non-BenQ brand projector ceiling mount kit, there is a safety risk that the

projector may fall from the ceiling due to an improper attachment through the use of

the wrong gauge or length screws.

You can purchase a BenQ projector ceiling mount kit from the place you purchased

your BenQ projector. BenQ recommends that you also purchase a separate Kensington

lock compatible security cable and attach it securely to both the Kensington lock slot

on the projector and the base of the ceiling mount bracket. This will perform the

secondary role of restraining the projector should its attachment to the mounting

bracket become loose.

Introduction12

Remote control

1. Power

Toggles the projector between standby

mode and on. See "Starting up the

projector" on page 24 and "Shutting down

the projector" on page 42 for details.

2. Freeze

Freezes the projected image. See "Freezing

the image" on page 40 for details.

3.

Starts the FAQ function. See "Utilizing FAQ

function" on page 40 for details.

4. Capture

Captures current displayed screen to be

MyScreen. See "Creating your own startup

screen" on page 37 for details.

5. Blank

Used to hide the screen picture. See "Hiding

the image" on page 39 for details.

6. Digital Zoom keys (+, -)

Magnifies or reduces the projected picture

size. See "Magnifying and searching for

details" on page 32 for details.

7. Volume +/-

Adjusts the sound level. See "Adjusting the

sound" on page 41 for details.

8. Menu/Exit

Turns on the On-Screen Display (OSD)

menu. Goes back to previous OSD menu,

exits and saves menu settings.

See "Using the menus" on page 27 for

details.

9. Keystone/Arrow keys ( / Up, /

Down)

Manually corrects distorted images

resulting from an angled projection. See

"Correcting keystone" on page 26 for

details.

10. Auto

Automatically determines the best

picture timings for the displayed image.

See "Auto-adjusting the image" on page

25 for details.

11. Left/ Right

When the On-Screen Display (OSD)

menu is activated, the #9 and #11 keys

are used as directional arrows to select

the desired menu items and to make

adjustments. See "Using the menus" on

page 27 for details.

12. Mode/Enter

Selects an available picture setup

mode. See "Selecting a picture mode" on

page 34 for details.

Activates the selected On-Screen

Display (OSD) menu item. See "Using

the menus" on page 27 for details.

13. Source

Displays the source selection bar. See

"Switching input signal" on page 31 for

details.

14. Page Up/Down

Page up/down arrows when connected

through USB to a PC. See "Remote

paging operations" on page 39 for details.

1

13

2

3

6

16

8

9

10

15

11

12

11

7

14

4

6

I

Introduction 13

Infra-Red (IR) remote control sensor is located on the front of the projector. The remote

control must be held at an angle within 30 degrees perpendicular to the projector's IR

remote control sensor to function correctly. The distance between the remote control and

the sensor should not exceed 8 meters (~ 26 feet).

Make sure that there are no obstacles between the remote control and the IR sensor on the

projector that might obstruct the infra-red beam.

Replacing the remote control battery

1. Pull out the battery holder.

Please follow the illustrated instructions. Push and hold

the locking arm while pulling out the battery holder.

2. Insert the new battery in the holder. Note the

positive polarity should face outward.

3. Push the holder into the remote control.

• Avoid excessive heat and humidity.

• There may be battery damage if the battery is

incorrectly replaced.

• Replace only with the same or equivalent type recommended by the battery manufacturer.

• Dispose of the used battery according to the battery manufacturer’s instructions.

• Never throw a battery into a fire. There may be danger of an explosion.

• If the battery is dead or if you will not be using the remote control for a long time, remove

the battery to prevent damage to the remote control from possible battery leakage.

15. Timer On

Activates or displays an on-screen timer

based on your own timer setting. See

"Setting the presentation timer" on page

38 for details.

16. Timer Setup

Enters presentation timer setting directly.

See "Setting the presentation timer" on

page 38 for details.

• Operating the projector from the front • Operating the projector from the rear

Approx. 15°

Positioning your projector14

Positioning your projector

Choosing a location

Your room layout or personal preference will dictate which installation location you select.

Take into consideration the size and position of your screen, the location of a suitable power

outlet, as well as the location and distance between the projector and the rest of your

equipment.

Your projector is designed to be installed in one of four possible installation locations:

Your room layout or personal preference will dictate which installation location you select.

Take into consideration the size and position of your screen, the location of a suitable power

outlet, as well as the location and distance between the projector and the rest of your

equipment.

1. Front Table

Select this location with the projector placed near the

floor in front of the screen. This is the most common way

to position the projector for quick setup and portability.

2. Front Ceiling

Select this location with the projector suspended upside-

down from the ceiling in front of the screen.

Purchase the BenQ Projector Ceiling Mounting Kit from

your dealer to mount your projector on the ceiling.

Set Front Ceiling in the SYSTEM SETUP: Basic >

Projector Position menu after you turn the projector on.

3. Rear Table

Select this location with the projector placed near the

floor behind the screen.

Note that a special rear projection screen is required.

Set Rear Table in the SYSTEM SETUP: Basic > Projector

Position menu after you turn the projector on.

4. Rear Ceiling

Select this location with the projector suspended upside-

down from the ceiling behind the screen.

Note that a special rear projection screen and the BenQ

Projector Ceiling Mounting Kit are required for this

installation location.

Set Rear Ceiling in the SYSTEM SETUP: Basic >

Projector Position menu after you turn the projector on.

Positioning your projector 15

Obtaining a preferred projected image size

The distance from the projector lens to the screen, the zoom setting (if available), and the

video format each factors in the projected image size.

16:10 is the native aspect ratio of this projector. To be able to project a complete 16:9

(widescreen) aspect ratio image, the projector can resize and scale a widescreen image to the

projector's native aspect width. This will result in a proportionally smaller height equivalent

to 90% of the projector's native aspect height.

The projector should always be placed horizontally level (like flat on a table), and positioned

directly perpendicular (90° right-angle square) to the horizontal center of the screen. This

prevents image distortion caused by angled projections (or projecting onto angled surfaces).

If the projector is mounted on a ceiling, it must be mounted upside-down so that it projects

at a slightly downward angle.

You can see from the diagram on page 17, that this type of projection causes the bottom edge

of the projected image to be vertically offset from the horizontal plane of the projector.

When ceiling mounted, this refers to the top edge of the projected image.

If the projector is positioned further away from the screen, the projected image size

increases, and the vertical offset also increases proportionately.

When determining the position of the screen and projector, you will need to account for

both the projected image size and the vertical offset dimension, which are directly

proportional to the projection distance.

BenQ has provided a table of 16:10-aspect-ratio screen sizes to assist you in determining the

ideal location for your projector. There are two dimensions to consider, the perpendicular

horizontal distance from the center of the screen (projection distance), and the vertical

offset height of the projector from the horizontal edge of the screen (offset).

16:10 aspect image in a 16:10

aspect display area

16:9 aspect image scaled to a 16:10 aspect

display area

Positioning your projector16

How to determine the position of the projector for a given

screen size

1. Select your screen size.

2. Refer to the table on page 17 and find the closest match to your screen size in the left

columns labelled "Screen size". Using this value, look across this row to the right to

find the corresponding average distance from screen value in the column labelled

"Average". This is the projection distance.

3. On that same row, look across to the right column and make note of the "Vertical

offset (mm)" value. This will determine the final vertical offset placement of the

projector in relation to the edge of the screen.

4. The recommended position for the projector is aligned perpendicular to the

horizontal center of the screen, at the distance from the screen determined in step 2

above, and offset by the value determined in step 3 above.

For example, if you are using a 120-inch screen, the average projection distance is 3894 mm

and with a vertical offset of 25.1 mm.

How to determine the recommended screen size for a

given distance

This method can be used for situations where you have purchased this projector and would

like to know what screen size will fit in your room.

The maximum screen size is limited by the physical space available in your room.

1. Measure the distance between the projector and where you want to position the

screen. This is the projection distance.

2. Refer to the table on page 17 and find the closest match to your measurement in the

average distance from screen column labelled "Average". Check that your measured

distance is between the min and max distances listed on either side of the average

distance value.

3. Using this value, look across that row to the left to find the corresponding "Screen size"

listed in that row. That is the projected image size of the projector at that projection

distance.

4. On that same row, look across to the right column and make note of the "Vertical

offset (mm)" value. This will determine the final placement of the screen in relation to

the horizontal plane of the projector.

For example, if your measured projection distance was 4.0 m (4000 mm), the closest match

in the "Average" column is 3894 mm. Looking across this row shows that a 120-inch screen is

required.

If you place the projector in a different position (to that recommended), you will have to tilt

it down or up to center the image on the screen. In these situations, some image distortion

will occur. Use the Keystone function to correct the distortion. See "Correcting keystone" on

page 26 on page for details.

Positioning your projector 17

Projection dimensions

Refer to "Dimensions" on page 64 for the center of lens dimensions of this projector before

calculating the appropriate position.

There is 3% tolerance among these numbers due to optical component variations. BenQ

recommends that if you intend to permanently install the projector, you should physically test

the projection size and distance using the actual projector in situ before you permanently

install it, so as to make allowance for this projector's optical characteristics. This will help you

determine the exact mounting position so that it best suits your installation location.

Maximum zoom Minimum zoom

Projection distance

Center of lens

Screen

Vertical offset

Screen size Distance from screen (mm) Ver t ical o f f s e t

(mm)

Diagonal W

(mm)

H

(mm)

Min length Average Max length

Inch mm (max. zoom) (min. zoom)

30 762 646 403 1018 1127 1235 6.1

40 1016 861 538 1273 1420 1567 8.3

50 1270 1077 673 1564 1731 1897 10.5

60 1524 1292 807 1871 2047 2223 12.6

80 2032 1723 1077 2435 2658 2881 16.4

100 2540 2153 1346 3014 3276 3538 20.5

120 3048 2584 1615 3594 3894 4194 25.1

150 3810 3230 2019 4465 4823 5180 31.3

200 5080 4307 2692 5916 6369 6822 41.6

220 5588 4738 2961 6496 6987 7478 45.7

250 6350 5384 3365 7367 7916 8464 52.1

300 7620 6461 4038 8818 9462 10106 62.4

Connection18

Connection

When connecting a signal source to the projector, be sure to:

1. Turn all equipment off before making any connections.

2. Use the correct signal cables for each source.

3. Ensure the cables are firmly inserted.

• In the connections shown below, some cables may not be included with the projector (see

"Shipping contents" on page 8). They are commercially available from electronics stores.

• For detailed connection methods, see pages 19-23.

1. VGA cable 5. Component Video to VGA (DSub)

adapter cable

2. VGA to DVI-A cable 6. Video cable

3. USB Cable 7. S-Video cable

4. Audio Cable 8. HDMI cable

3

12

14

544

86

7

Connection 19

Connecting a computer or monitor

Connecting a computer

The projector can connect to both IBM® compatibles and Macintosh® computers. A Mac

adapter is needed if you are connecting legacy version Macintosh computers.

To connect the projector to a notebook or desktop computer:

1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the

computer.

2. Connect the other end of the VGA cable to the COMPUTER 1 or COMPUTER 2

signal input jack on the projector.

3. If you wish to make use of the projector (mixed mono) speaker(s) in your

presentations, take a suitable audio cable and connect one end of the cable to the audio

output jack of the computer, and the other end to the AUDIO jack of the projector.

When you connect audio output signal from a computer, please balance out the

volume control bar to obtain an optimal sound effects.

4. If you wish, you can use another suitable audio cable and connect one end of the cable

to the AUDIO OUT jack of the projector, and the other end to your external speakers

(not supplied).

Once connected, the audio can be controlled by the projector On-Screen Display

(OSD) menus. See "Audio Settings" on page 52 for details.

The built-in speaker will be muted when the AUDIO OUT jack is connected.

Many notebooks do not turn on their external video ports when connected to a projector.

Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a

function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press

FN and the labeled function key simultaneously. Refer to your notebook's documentation to

find your notebook's key combination.

Connecting a monitor

If you want to view your presentation close-up on a monitor as well as on the screen, you

can connect the MONITOR OUT signal output jack on the projector to an external monitor

following the instructions below:

To connect the projector to a monitor:

1. Connect the projector to a computer as described in "Connecting a computer" on page

19.

2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to the

D-Sub input jack of the video monitor.

Or if your monitor is equipped with a DVI input jack, take a VGA to DVI-A cable and

connect the DVI end of the cable to the DVI input jack of the video monitor.

3. Connect the other end of the cable to the MONITOR OUT jack on the projector.

• The output signal for MONITOR OUT jack only works when the input signal comes from

COMPUTER 1 or COMPUTER 2 jack. When the projector is powered on, the output signal

from MONITOR OUT jack varies depending on the input signal from COMPUTER 1 or

COMPUTER 2 jack.

• If you wish to use this connection method when the projector is in standby mode, make

sure the Standby Monitor Out function is turned on in the SYSTEM SETUP: Advanced

menu. See "Standby Monitor Out" on page 53 for details.

Connection20

Connecting Video source devices

You need only connect the projector to a Video source device using just one of the above

connecting methods, however each provides a different level of video quality. The method

you choose will most likely depend upon the availability of matching terminals on both the

projector and the Video source device as described below:

Connecting audio

The projector has one built-in mono speaker which is designed to provide basic audio

functionality accompanying data presentations for business purposes only. It is not designed

for, nor intended for stereo audio reproduction use as might be expected in home theater or

home cinema applications. Any stereo audio input (if provided), is mixed into a common

mono audio output through the projector speaker.

When you connect audio output signal from a video source device, please set the audio

output in dual track to obtain an optimal sound effects.

If you have a separate sound system, you will most likely want to connect the audio output

of your Video source device to that sound system, instead of to the mono audio projector.

The audio connections illustrated on page 18 are provided for informational purposes only.

You need not connect audio to the projector if there is an alternate sound system available,

or if audio is not required.

Te r m i n a l

name

Terminal appearance Reference Picture quality

HDMI

HDMI "Connecting an

HDMI source device"

on page 21 Best

Component Video

COMPUTER "Connecting a

Component Video

source device" on

page 22

Better

S-Video

S-VIDEO "Connecting an S-

Video/composite

source device" on

page 23

Good

Video

VIDEO

Normal

Page is loading ...

BenQ MS510 User manual

BenQ MS510 User manual

Related papers