Seek Thermal Attack Pro User manual

Brand: Seek Thermal

Model: Attack Pro

Category: Camera housings

Type: User manual

Seek Thermal Attack Pro is a powerful thermal imaging camera that can help you see in the dark, through smoke, and even underwater. It's perfect for hunting, search and rescue, and home security. With its long battery life and rugged construction, the Attack Pro is ready for anything you throw its way.

IMPORTANT SAFETY INFORMATION

READ ENTIRE MANUAL BEFORE USE

User manual

Important safety information. Read entire manual before use.

1 Safety and usage information

FCC Statement:

This device has been tested and found to comply with part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment o and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

IC Statement:

CAN ICES-003 (B) / NMB-003 (B)

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de

brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le fonctionnement.

“This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est

conforme à la norme’

European Union:

RFI Emissions: EN 55032

Immunity: EN 55035

Electrical Safety: EN/IEC 62368-1

ROHS: This RoHS-compliant product conforms to the European Union Restriction of the Use of Certain

Hazardous Substances (RoHS) in Electrical and Electronic Equipment. Seek Thermal ensures RoHS

conformance by requiring supplier Declarations of Conformity, monitoring incoming materials, and maintaining

manufacturing process controls.

WEEE: This symbol on the product(s) and / or accompanying documents means that used electrical and

electronic equipment should not be mixed with general household waste. For proper treatment, recovery

and recycling, please take this product(s) to designated collection points where it will be accepted free of

charge. Alternatively, in some countries, you may be able to return your products to your local retailer upon

purchase of an equivalent new product.

1 (7)

AttackPRO Series truck charger user manual

www.thermal.com

2 (7)

AttackPRO Series truck charger user manual

1 Safety and usage information (continued)

Disposing of this product correctly will help save valuable resources and prevent any potential negative eects

on human health and the environment, which could otherwise arise from inappropriate waste handling.

Please contact your local authority for further details of your nearest designated collection point.

Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation.

Important safety information

WARNING – INDICATES A HAZARDOUS SITUATION THAT, IF NOT AVOIDED, COULD RESULT IN DEATH OR

SERIOUS INJURY

CAUTION – INDICATES A HAZARDOUS SITUATION THAT, IF NOT AVOIDED, COULD RESULT IN MINOR OR

MODERATE INJURY

NOTICE – INDICATES INFORMATION CONSIDERED IMPORTANT, BUT NOT HAZARD-RELATED

WARNING

1. Never recharge in a potentially explosive environment.

2. A lithium battery with a damaged enclosure should not be exposed to water.

CAUTION

1. This truck charger is intended to be mounted on a ﬂat and stable surface in a suitable location where there

is no risk of physical impact or acceleration forces.

2. Alternatively, this truck charger may be securely mounted to a vertical or horizontal surface in a location

deemed safe and appropriate by the party performing the installation

3. Remove any water or moisture from the battery before you install it. Do not apply solvents or equivalent

liquids to the enclosure, cables, or other items. Damage to the components can occur.

4. Disconnect the AttackPRO truck charger from the AC power source before cleaning.

NOTICE

1. Use only an approved power supply provided by Seek Thermal.

2. If choosing to mount and hardwire the truck charger in any apparatus, make sure installation is done by

professional installers.

3. As with most electronic products, this equipment must be disposed of in an environmentally friendly way

and in accordance with existing regulations for electronic waste.

4. Do not alter or cover over any labels on the truck charger.

5. This truck charger should be placed in a location that is average room temperature (73˚F/ 23˚C),

protected from weather, water, chemicals, and direct long term sunlight exposure.

6. The charger is suitable only for indoor use.

7. Only for use with Seek Thermal AttackPRO Cameras (model FQ-PPAX, FQ-PPNX and model FA-BAA

Battery Pack).

8. Contact your distributor for servicing by authorized personnel. This component contains no user-serviceable

components.

9. Clean the battery contacts and also those of the camera prior to component installation.

www.thermal.com

3 (7)

2 What’s included in the box

• Truck charger unit

• Power supply (for AC power)

• AC plugs for US, EU, and UK (for Power Supply)

• Accessory Kit : Fuse holder/fuse, Self-tapping mounting fasteners x 3, 12/24VDC Terminal connector,

Feet for desktop/table use x 4.

• Quick start guide

Seek Thermal reserves the right to discontinue models, parts, accessories, additional items, and product

speciﬁcations at any time without prior notice.

3 Illustrations

AttackPRO Series truck charger user manual

Power/Charge LED

DC PlugCharging

Contacts

BackFront

Internal 3A fuse

Charger power LED indicator

Battery strap

12/24VDC input

Camera retention slot

Camera strap

Camera charger well

Camera rentention lip

Mounting hole locations

DC input jack

Battery retention slot

12/24VDC terminal connector

Battery charger well

Battery charger cover plate

Battery charging LED indicator

www.thermal.com

AttackPRO Series truck charger user manual

4 (7)

4 Technical Speciﬁcations

Equipment ratings

Recommended Fuse and Cable for hardwire install

Please contact your local authority for further details of your nearest designated collection point.

The back surface of the truck charger allows connection to apparatus 12/24VDC systems using the terminal

connector instead of the included AC/DC switching power supply. Please consult the appropriate installation

services to safely and properly connect this to apparatus using the included terminal, fuse, and fuse holder.

5 Hardwiring and Mounting Instructions

1. Select a suitable mounting location inside the apparatus and refer to the hardwiring diagram in Section 6.

2. Use the AttackPRO truck charger itself (WITHOUT POWER CONNECTED) or use a template available

from thermal.com to mark the mounting hole locations on the preferred mounting surface; these

correspond to the 3 thru hole locations in the charger housing for mounting (a).

3. Install secured and permanent cables (not provided) running from the apparatus 12/24VDC supply to

the rear of the AttackPRO truck charger at the selected mounting location, BUT DO NOT CONNECT

THIS CABLE TO THE 12/24VDC SOURCE AT THIS TIME.

4. This cable routing must contain an in line fuse installed close to the battery (a fuse and fuse holder

is provided). Cables, crimps, and battery connectors are not provided.

5. Connect the positive and negative wires that will terminate at the AttackPRO truck charger to the

included terminal connector (c) (green). Plug the terminal connector into the rear of AttackPRO truck

charger (d), routing any cables thru the appropriate channels for clearance.

Note : Check the polarity when you connect the cable to the terminal connector

6. Attach the truck charger to the selected surface using the included self tapping screws or other

hardware necessary to ensure the unit is secure and safely mounted.

7. Permanently connect the positive and negative cables (not provided) to the apparatus 12/24VDC supply.

Supply Voltage

Power Rating

Environmental

24W

12VDC

0˚C to 40˚C operating, 10%-90% RH

Dimensions

Weight

Charge Time (battery)

~2lbs (0.9kg)

10” x 9.1” x 5”

~ 6hrs

Charge Time (camera) ~ 6hrs

Cable

Fuse

Environmental

Auto 3A 32VDC Blade mini

16AWG Stranded SAE J1128

Intended for indoor use only

www.thermal.com

5 (7)

AttackPRO Series truck charger user manual

www.thermal.com

POS(+)NEG(–)

POS(+) NEG(–)

6 Hardwiring Diagram and System Overview

A. Mounting hole locations

B. Fuse holder and fuse

C. Included terminal connector

D. Terminal connector plug location

7 Quick start guide

1. Place the truck charger on a suitable stable surface or securely mount to a horizontal or vertical surface,

as above.

2. Plug the barrel end connector of the power supply into the back of truck charger (e), note power supply

will need to be connected before step 1 if securely mounting the charger.

3. Determine the appropriate AC plug interface (US/EU/UK) for your region and attach

to the power supply face.

4. Plug the power supply into a safe AC power source. The blue light on the charger (f) should indicate

power received.

5. Place the battery in the battery charger well (g) with the label facing inward and the charging contacts

pointed upward, and under the top contact cover plate (h). Make sure the bottom of the battery is

properly seated in the retention slot (i). Secure the battery with the attached strap (j).

6. The LED on the charger should light as follows:

a. Solid RED = battery is charging.

b. Solid GREEN = battery is fully charged.

c. Blinking RED = there is an error with charging.

7. Place the AttackPRO thermal imaging camera in the camera charger well (l), with the display facing

outward, and the upper surface near the label ﬁtting under the upper retention lip (m) of the well.

Make sure the bottom of the camera is properly seated in the retention slot (n). Secure with the

attached strap (o).

8. The display on the AttackPRO should light and indicate charging status. The display will go dark after

approx. 3 seconds. To wake the display and check charge status, press any button on the camera.

8 Cleaning and care

The AttackPRO truck charger requires little maintenance. For best care, please follow the guidelines below:

• Unplug or disconnect the power supply from the power source before any cleaning

• Gently use a cotton swab damped with isopropyl alcohol to wipe the contacts if they appear dirty or

covered with debris

• To clean the charger housing, use a soft cloth with warm water only and a mild detergent. Do not use

solvents to clean the charger

• Do not allow any liquids or debris to enter the charger

• Damaged or broken retention straps may be ﬁeld replaceable by removing either the battery or camera

retention slots and inserting a new retention strap

Seek Thermal reserves the right to discontinue models, parts, accessories, additional items, and product

speciﬁcations at any time without prior notice.

9 Customer and product support

For any questions or issues with the use of this product, do not hesitate to contact our customer support

group at www.thermal.com/support.

AttackPRO Series truck charger user manual

6 (7) www.thermal.com

AttackPRO Series truck charger user manual

7 (7) www.thermal.com | PN 4307 REV3

Ensure the 12/24VDC hardwire source is properly providing power, check

for blown fuse and replace if necessary.

Issues: Solutions:

Ensure either the switching AC power supply is properly inserted into a

working AC receptacle OR

Power LED does not light when power source is

connected to charger

Battery will not charge. Clean battery charging contacts.

Make sure AttackPRO is properly seated in the charging well and making

contact with the retention strap securely fastened.

Make sure a battery is installed in the AttackPRO and the battery door is

secured.

Try inserting the battery only into the battery charge slot of the charger to

note behavior.

Ensure battery is inserted correctly.

Try reinserting the battery.

Battery LED does not light when battery is

inserted.

RED flashing indicator when battery inserted.

AttackPRO does not indicate charging when

inserted.

Ensure AC power source is adequate and safe.

Replace/charge battery.

Ensure battery contacts are clean.

Try an alternate battery.

10 Troubleshooting

If you are experiencing problems with your product, please refer to this checklist. If the problem persists,

please contact Seek Thermal Customer Services or your local distributor.

Power and charging

Seek Thermal Inc.

6300 Hollister Avenue

Santa Barbara, CA 93117

www.thermal.com

www.thermal.com/support

Disclaimer

Speciﬁcations subject to change without further notice. Models and accessories subject to regional market

considerations. License procedures may apply. Products described herein may be subject to US Export

Regulations. Please refer to thermal.com/support with any questions.

Seek Thermal Attack Pro User manual

Brand: Seek Thermal

Model: Attack Pro

Category: Camera housings

Type: User manual

Download PDF

report

Seek Thermal Attack Pro User manual

Seek Thermal Attack Pro User manual

Related papers

Other documents