Home Decorators Collection SW1787 MBK Operating instructions

Item #XXXXXXX

Model #SW1787 MBK

ALDERBROOK LED 60 INCH CEILING FAN

Attaching the decorative cover

Attaching the Blade Arm

Attaching the Fan Blades

Hanging the Fan

To reduce the risk of ﬁre or electric shock, this

fan should only be used with fan speed control part

NO.:DL-1170FCS-08, manufactured by: Summer Wind

International. ,Ltd.

60 in.(1,52 m)

120

Fan

size Watts RPM CFMSpeed Volts Amps N.W. G.W. C.F.

1.78’ ft.

5.42kgs

(11.92 lbs)

6.6 kgs

(14.52lbs)

0.04

0.05

0.07

0.12

0.18

0.28

2.01

2.78

4.13

6.31

9.64

16.91

44

65

85

105

125

153

1381

2106

2877

3684

4411

5416

1

2

3

4

5

6

KK

LL

KK

LL Blade arm screw pre-assembled)

Decorative cover screw

Allen wrench

7

5

2

(pre-assembled)

7

Decorative Cover

Blade arm

(pre-assembled)

2

I

Attaching the decorative cover

□

II

□

II

FF GG

HH

EE

GG

FF

I

KK

I

G

Attaching the decorative cover

Attach the decorative covers (G) to the coupling of the

fan motor assembly (I) by using the decorative cover

screws (KK) . Ensure all the screws (KK) are tightened.

Repeat process for the other decorative cover(G)

LL

I

H

G

I

G

Attaching the Blade Arm

Attaching the blade arm to fan motor assembly

Remove the blade arm screws (LL) from the fan motor assembly (I).

9

LL

Align the holes in the bottom of the fan motor assembly (I)

and the blade arm (H), and secure with the blade

arm screws (LL). Ensure all the screws (LL) are tightened.

AA

BB

A

I

G

H

A

I

Attaching the Fan Blades

Fastening the blades to blade arm

Attach the blade (A) to the blade arm (H) by using the blade

screws (AA). Tightened all the screws (AA) by using the

Allen wrench (BB).

Hanging the Fan

Place the slots from the mounting bracket (B) over the two

screws provided with the outlet box.slide the mounting

bracket (B) until it locks in place at the narrow section

of the slots.

G

A

I

G

A

I

MM

Slip the canopy cover (D), and canopy (C) onto the

downrod (F).Carefully reinstall the hanger ball (E) onto

the downrod (F), and ensure that the cross pin (EE) is in

the correct position, the set screws (HH) are tight, and

the wires are not twisted.

D

Attaching the canopy cover, and

canopy to the downrod

Making the electrical connections

WARNING: To avoid possible electrical shock, ensure the

electricity is turned off at the circuit breaker or main fuse box

before wiring.

WARNING: Check to see that all connections are tight,

including the ground, and that no bare wire is visible at the

wire nuts, except for the ground wire.

Motor to Receiver Electrical Connections:

Connect the YELLOW wire from the fan to the YELLOW wire

marked “MOTOR 1” from the Receiver.

Connect the RED wire from the fan to the RED wire marked

“MOTOR 2” from the Receiver.

Connect the GREY wire from the fan to the GREY wire marked

“MOTOR 3” from the Receiver.

Receiver to House Supply Wires Electrical connections:

Connect the WHITE wire (Neutral) from the outlet box to the

WHITE wire marked ”AC in N” from the receiver.

Connect the BLACK wire (Hot) from the outlet box to the BLACK

wire marked “AC in L” from the receiver.

If your outlet box has a GROUND wire (Green or Bare

Copper),connect this wire to the Hanger Ball and Hanger

Bracket and receiver Ground wires.

If your outlet box does not have a Ground Wire, then connect the

Hanger Ball and Hanger Bracket and Receiver Ground Wire

together.

Secure wire connection with the plastic wire nuts (DD)

provided. Especially , for the ground wires, please use bigger wire

nut (DD) provided.

After all splices are made, check to make sure there are no

loose strands.

Note: Fan must be installed from a maximum distance of 40 feet

(12.2 m) from the transmitting unit for proper signal transmission

between the transmitting unit and the fan’s receiving unit.

Insert the receiver (J) into the mounting bracket (B) with the ﬂat

side of the receiver (J) facing the ceiling.

Follow the steps below to connect the fan to your house supply

wires. Secure the wire nuts supplied with your fan by wrapping the

connections with electrical tape.

G

A

I

J

B

J

Outlet Box

Yellow

Red

Grey

Black

Green

White

DD (x7)

JJ

K

M

(M)

K

1.2.3.4.5.6 buttons:

NN

Learning process

A23G 12V

the fan will begin to rotate for a short period and then shut off.

Controls the fan direction.

To change the direction of the rotation of the blades

the fan muse be in operation.

L

Reverse function button : Controls the fan direction.

CC

13

KK

LL

Decorative Cover

Blade arm

KK

LL Blade arm screw

Decorative cover screw

Allen wrench

18

Home Decorators Collection SW1787 MBK Operating instructions

Home Decorators Collection SW1787 MBK Operating instructions

Related papers

Other documents