Victor 1280-7 Owner's manual

1

1280-7

12 DIGIT PROFESSIONAL PRINTING CALCULATOR

CALCULATRICE IMPRIMANTE PROFESSIONNELLE À 12 CHIFFRES

CALCULADORA IMPRESORA PROFESIONAL DE 12 CIFRAS

INSTRUCTION MANUAL

MANUEL DU FONCTIONNEMENT

MANUAL DE INSTRUCCIONES

Preface

Congratulations on your choice of the Victor 1280-7 electronic calculator. Careful

design, quality materials, and advanced research and production facilities have given you

a calculator that with proper care will provide years of trouble-free service.

Table of Contents

Preparation 1 - 2

General Maintenance 2

How to Feed the Paper 2

Replacing the Ribbon 3

Keyboard Layout 4

Key and Slide Switch Features 4 - 10

Display Symbols 10

Reset Button 10

Using the Wireless Data Relay 11

Resetting the Wireless USB Connection 12

Specifications 13

Application Examples 14 - 23

Warranty 24

Preparation

BEFORE USING THE PRINTER FOR THE FIRST TIME:

Remove the tape holding the ink ribbon in place.

1. Remove the tape holding the printer cover in place.

2. Dispose of the tape.

3. Lift the printer cover up and then off.

4. Remove and dispose of the tape holding the ribbon in place.

(Fig. 1) (Fig. 2)

Before Beginning Calculation

1. Plug in AC power

2. Be sure the paper roll and ribbon have been installed properly.

3. Turn power switch on and make sure the display lights. A “C” will

automatically be printed on the paper tape.

4. Set decimal point selector switch to the desired position.

.General Maintenance

1. Do not place the calculator in hot, dusty, or damp locations.

2. To clean the housing, use a moist towel.

3. Do not place any items on the housing, particularly on the head of the printer

mechanism.

4. Turn off the power before removing the plug from AC wall outlet.

5. Turn the power off while not in use.

How to Feed the Paper Tape

1. Plug in the calculator and turn it on.

2. Cut or tear evenly the end of the paper roll to get a straight edge.

3. Place the paper holder into position. (Fig. 3)

4. Install the paper roll on the paper holder.

5. Insert the paper end into the printer slot. (Fig. 4)

6. Press the Paper Feed (↑) key to feed the paper to an adequate length.

(Fig. 3) (Fig. 4)

Replacing the Ribbon

Your calculator is shipped with a 2-color ribbon already in place. You do not need to

install or change it before you begin using the calculator. When you have been using

your calculator for some time, however, the print will gradually become faint, indicating

that you should change the ribbon. To change the ribbon, follow these steps.

1. Remove the paper roll, tearing the paper at the rear of the calculator. Use the

Paper Advance (↑) key to feed the remaining paper tape through the printer.

Then remove the printer cover.

2. Remove the old ribbon by pulling it upward. (Fig 6 shows the printer without

a ribbon.)

3. Install the ribbon spool with the black edge up. Victor recommends the Victor

7010 (Fig. 5).

4. Place the spool with the greater amount of ribbon on the left post.

5. Next unwind the ribbon as it is placed along the outside of the guides and in

front of the print wheel. (Fig. 7)

6. Rotate the spools to take up any slack. Replace the printer cover and the

paper tape.

(Replace with the Victor #7010 Ink Ribbon)

(Fig. 5) (Fig. 6)

(Fig. 7)

Keyboard Layout

This section describes the mode switches, data entry keys, and operating keys provided

on your calculator.

Key and Slide Switch Features

OFF ON

OFF The power is OFF.

ON The power is ON.

P NP PC

P Print Mode: The printer is activated as long as the calculator is turned on.

NP Non Print Mode: The printer is activated only when the paper feed key or the

non-add / date key (#/S) is pressed. This is also called the display only mode.

PC PC Mode: In this mode the calculator will send the information entered to a

computer just as it would to the paper in a printer. The number entered will

appear in the first column and the operation performed will appear in the second

column. This is also called the Paperless Tape Mode.

• The Wireless Data Relay device must be installed into the computer’s USB

port when using any of the three PC Modes.

Wireless Data Relay (Fig. 9)

▲ 5/4 ▼

▲ Round Up Mode: The ▲ setting causes an answer to a calculation to

automatically round up.

5/4 Split Rounding Mode: This setting causes automatic round off. If the first digit

of the answer beyond the decimal setting is 0 to 4, the value is rounded down.

Otherwise the value is rounded up.

▼ Round Down Mode: Causes calculations to automatically round down.

(Truncate)

Σ • GT

Σ Sigma Mode: When the slide switch is in the Sigma position, the results of

multiplication or division calculations completed by the = or % keys are

automatically added to the accumulator. The accumulated answer can be recalled

by pressing the T key.

• The calculator is in neither Sigma mode nor Grand Total mode.

GT Grand Total Mode: Any total created with the T key is automatically

accumulated to memory. The accumulated Grand Total can be recalled by

pressing the MT key.

A 0 2 3 F Kpad

A Monetary Add Mode: In this setting, amounts entered are assumed to be

monetary. The calculator automatically supplies a decimal point to the left of the

last two digits entered.

0 2 3 Fixed Digit Mode: These settings specify the number of digits to the right of the

decimal point that are shown in the result.

F Floating Decimal Point Mode: This setting specifies that all digits of the result

are shown, up to a maximum of 12. If the result exceeds these capacities, excess

digits to the right of the decimal point are dropped. No rounding takes place.

Kpad Keypad Mode: In this mode, the calculator acts as a keypad for the operator’s

computer. As numbers keys are pressed the entry is instantly sent to the

computer’s display. The T (Total) key acts as an Enter key and the Memory keys

act as Arrow keys to move cell to cell in a spreadsheet.

• The Wireless Data Relay device must be installed into the computer’s USB

port when using any of the three PC Modes.

Key Functions

0 – 9, 00, . Numeric Keys: The calculator uses the conventional 10 – key indexing

keyboard, and includes the double zero and decimal point keys. Whole numbers are

entered exactly as they are written.

Paper Feed Key: Used to advance the paper.

Right Shift Key: Used to delete the right most character of a live entry.

Percent Key: Completes percent calculations when Multiplication or Division

keys are used.

Division Key: The Division key performs division, automatic constant division,

and intermediate sequential operations. It establishes the next amount as a

constant divisor. Each divisor entry is retained as a constant until the X, ÷, or

Clear (C/CE) keys are depressed.

Equal Key: Press the equal key to get the result for a multiplication or division

equation.

Format Key: The Equals key is also used as the Format Key when programming

the Date. The operator may choose to change the way the date is displayed

(MM/DD/YYYY, DD/MM/YYYY, OR YYYY/ MM/DD) by pressing this key

while in the Date setting mode.

Multiplication Key: The Multiplication key performs multiplication, automatic

constant multiplication, and intermediate sequential operations. It establishes the

amount as a constant multiplicand.

AM/PM Key: The Multiplication key is also used in the Time setting mode to

switch from AM to PM or vice versa.

Time / Date Key: Used to display the Time or Date. Press once to see the Date

and press a 2

nd

time to see the Time. To change either the Date or the Time, press

the IC / SET key while displaying the Date or the Time.

Change Sign Key: Inverts the sign of the displayed number at key entry.

12 / 24 Key: The change sign key is also used to toggle between the 12

(AM/PM) or 24 hour clock mode.

IC Key: Prints the current Item count.

SET Key: Used to set the Date and Time. Press and hold until the Date starts to

flash on the display (Approximately 3 seconds). Enter the correct Date and press

the Set key again to set the Time.

Clear / Clear Entry Key: Clears a live entry by pressing the key once. Press

twice to clear the accumulator or pending calculation. The Clear key does not

clear the Memory. To clear the memory, press the MT key.

Minus Key: Subtracts an amount from the accumulator. To subtract the same

amount more than one time (repeat subtraction), enter that amount once and

depress the Minus key as many times as necessary. If this key is depressed

immediately after the (%) key, it works as a percent minus key.

Plus Key: Adds an amount to the accumulator. To add the same amount more

than one time (repeat addition), enter that amount once and depress the Plus key

as many times as necessary. If this key is depressed immediately after the (%)

key, it works as a percent add key.

Send To PC Key: This key is used to send the information in the calculator’s

display to the cursor of a personal computer. The information is sent exactly as it

is displayed on the calculator.

• The Wireless Data Relay device must be installed into the computer’s USB

port when using any of the three PC Modes.

Wireless Data Relay (Fig. 10)

Non Add Key: Will print a live entry as an identifier or as an invoice number

without adding the number to the accumulator. The number will appear on the

left hand side of the tape with the “#” sign.

Subtotal Key: Prints a subtotal, but does not clear the accumulator.

Total Key: Prints and clears the accumulator. This key will also print the total of

multiplication and division calculations when the slide switch is in the Sigma

mode (Σ).

Enter: When the calculator is in the Kpad mode, the T/Enter key acts as an Enter

key on a computer keyboard.

Memory + Key: Adds an amount to Memory. If there is a live calculation

pending, the Memory Plus key will complete the calculation and accumulate the

amount.

→ Key: Acts as an arrow key on a computer keyboard to move the cursor to the

right while the calculator is in the Kpad mode.

Memory – Key: Subtracts an amount from Memory. If there is a live calculation

pending, the Memory Minus key will complete the calculation and subtract the

amount from Memory.

← Key: Acts as an arrow key on a computer keyboard to move the cursor to the

left while the calculator is in the Kpad mode.

Memory Subtotal Key: Displays a subtotal of the memory contents. If the

calculator is in the Print mode, this subtotal will also print. Memory Subtotal

does not clear the contents of Memory.

↓ Key: Acts as an arrow key on a computer keyboard to move the cursor down

while the calculator is in the Kpad mode.

Memory Total Key: Prints and clears the total in Memory.

↑ Key: Acts as an arrow key on a computer keyboard to move the cursor up while

the calculator is in the Kpad mode.

Cost Sell Margin Keys

Cost, Sell, Margin keys are used for calculating cost, selling price, and profit

margin. Enter the value of any two variables to calculate the third. (Example:

Enter the cost of an item and press the Cost key. Next enter the selling price of an

item and press the Sell key. The Margin % will appear on the display and the

paper tape.)

Rate and Tax Keys

Tax 1 and Tax 2 keys are used to calculate an amount of tax using the preset tax

rate. Use the “+” key for calculating an amount including TAX, and the “-“ key

for calculating an amount excluding TAX.

To set TAX 1, press and hold the RATE key until the display flashes. Enter the

TAX Rate and then press TAX 1. TAX 1 is now set. To set TAX 2, follow the

same steps substituting TAX 2 for TAX 1.

Display Symbols

M A number has stored into memory.

E Error or over flow of capacity.

- The displayed value is negative.

RESET Button

Electromagnetic interference or electrostatic discharge may cause the display to

malfunction or the contents of the Memory to be lost or altered. Should this occur, use

the tip of a ball point pen or a paper clip to press the RESET button at the back of the

calculator.

After resetting the calculator set the calendar, clock, and tax rate again.

Using the Wireless Data Relay Device

The Victor 1280-7 has three different modes of operation when connected via the USB

device.

1. SEND TO PC MODE – Press this key to send the contents of the display to

the connected PC.

Example: User needs the total of the calculation 100 + 200 + 300 sent to

the computer. Enter 100 + 200 + 300 T into the calculator. Next press the

SEND TO PC key and the answer (600) will be sent to the computer.

2. KPAD MODE – In this mode, the calculator acts as a keypad for the

operator’s computer. As number keys are pressed the entry is instantly sent to

the computer’s display. The T (Total) key acts as an Enter key and the

Memory keys act as Arrow keys to move cell to cell in a spreadsheet.

3. PC / PAPERLESS TAPE MODE – In this mode the calculator will send the

information entered to a computer just as it would to the paper in a printer.

The number entered will appear in the first column and the operation

performed will appear in the second column.

(Fig. 9)

• The Wireless Data Relay device must be installed when using any of the three

PC Modes.

Wireless Data Relay (Fig. 10)

*Note: The Victor 1280-7 Wireless Calculator will not work with Apple

computers.

Resetting the Wireless USB Connection

There may be a need to occasionally repair or reset the connection between the calculator

and the USB device. Symptoms that can cause the connection to be lost include periods

of non-use, interference from another device, or connecting the USB device to a different

computer. If the connection is lost, please follow these instructions to re-connect the

calculator to the USB device:

1. Start your computer and your spreadsheet program such as Microsoft Excel.

2. Push the power switch to “ON” on your calculator.

3. Push to the right-most slide switch to “Kpad” on your calculator.

4. Plug the Victor 1280-7 Wireless USB receiver into a USB port on the computer.

5. Wait until your computer recognizes the USB device. A pop-up box may appear

in the lower right corner of your display. This should take no more than 30

seconds.

6. Press the blue “RATE” key and hold for about 2 seconds. The calculator display

will show “--------------“ until the Wireless USB receiver is connected.

7. Once the connection is complete, the calculator display will show “– PC –“

8. Select a cell in your spreadsheet (position your cursor in the spreadsheet).

9. Test the connection by pressing the number “3” on your calculator and pressing

“ENTER” (the “T” key)

If the above steps do not result in a connection try this alternative method:

2. Press the blue “RATE” key and hold for about 2 seconds. The calculator display

will show “--------------“.

3. Plug the Victor 1280-7 Wireless USB receiver into a USB port on the computer.

4. Wait until your computer recognizes the USB device. A pop-up box may appear

in the lower right corner of your display. This should take no more than 30

seconds.

5. Once the connection is complete, the calculator display will show “– PC –“

6. Select a cell in your spreadsheet (position your cursor in the spreadsheet).

7. Test the connection by pressing the number “3” on your calculator and pressing

“ENTER” (the “T” key)

If the alternative method does not result in a connection, you may see “ERROR” on the

display. Turn the machine off and on again and repeat the above procedures. If a

connection is still not made, please call 1-800-628-2420 for assistance.

• The Wireless Data Relay device must be installed when using any of the three

PC Modes.

Wireless Data Relay (Fig. 8)

If your Wireless Data Relay is lost or damaged and a new Relay is purchased from

Victor, these steps will need to be completed the first time the Relay is used.

Specifications

Display 12 Digit, Fluorescent

Printing Speed 4.6 Lines / Second

Printing Paper Width 2.25”, Diameter 3.15” Max

Width 57mm, Diamter 80mm Max

Power Sources 120V / 60 Hz (USA, CANADA)

Ambient Temperature 0°C ~ 40°C (32°F ~ 104°F)

Power Consumption 120V / 0.16A / 19.2W

Dimension 12.75” (L) X 8.75” (W) X 3.25 “ (H)

323 mm (L) X 220 mm (W) X 80 mm (H)

Ink Ribbon VICTOR 7010 (Twin Spool, C Wound Ribbon)

Printing Color 2 – Color (Negative numbers in red)

Weight 3.0 lbs. (1655 g)

Préface

Nous vous félicitons d’avoir choisi la calculatrice électronique Victor 1280-7. Une

conception minutieuse, des matières de qualité, une recherche avancée et des installations

de production d’avant-garde ont permis de créer cette calculatrice, qui vous procurera de

nombreuses années d'utilisation sans problème si vous l'entretenez correctement.

Table des matières

Préparation 1 - 2

Entretien général 2

Chargement du papier 2

Remplacement du ruban 3

Disposition du clavier 4

Caractéristiques des touches et des interrupteurs à glissière 4 - 10

Symboles affichés 10

Touche de réinitialisation 10

Utilisation de la transmission des données sans fil 11

Réinitialisation de la connexion USB sans fil 12

Caractéristiques techniques 13

Exemples d’utilisation 14 - 23

Garantie 24

Préparation

AVANT LA PREMIÈRE UTILISATION DE L’IMPRIMANTE :

Retirez le ruban collant qui maintient le ruban encreur en place.

1. Retirez le ruban collant qui maintient le couvercle de l’imprimante en place.

2. Jetez le ruban collant.

3. Levez le couvercle de l’imprimante, puis enlevez-le.

4. Retirez et jetez le ruban collant qui maintient le ruban encreur en place.

(Fig. 1) (Fig. 2)

Avant les premiers calculs

1. Branchez l'appareil dans une prise CA.

2. Assurez-vous que le rouleau de papier et le ruban ont été installés

correctement.

3. Mettez l’appareil sous tension et assurez-vous que l’afficheur s’allume. Un

« C » sera imprimé automatiquement sur le rouleau de papier.

4. Mettez l’interrupteur de sélection du point décimal à la position désirée.

Entretien général

1. Ne mettez pas la calculatrice dans un endroit chaud, poussiéreux ou humide.

2. Utilisez une serviette humide pour nettoyer le boîtier.

3. Ne placez rien sur le boîtier, en particulier sur la tête du mécanisme

d'impression.

4. Mettez la calculatrice hors tension avant de débrancher la fiche de la prise

murale CA.

5. Mettez la calculatrice hors tension quand elle ne sert pas.

Chargement du rouleau de papier

1. Branchez la calculatrice et mettez-la sous tension.

2. Coupez ou déchirez le bout du rouleau de papier afin d’obtenir un bord égal et

droit.

3. Mettez le porte-papier en position (fig. 3).

4. Placez le rouleau de papier dans le porte-papier.

5. Insérez l'extrémité du papier dans la fente de l’imprimante (fig. 4).

6. Appuyez sur la touche d’alimentation papier (↑) pour faire avancer le papier

jusqu’à ce qu'il soit d’une longueur adéquate.

(Fig. 3) (Fig. 4)

Remplacement du ruban

Votre calculatrice est équipée d’un ruban à deux couleurs, déjà installé. Vous n’avez

donc pas besoin de l’installer ou de le changer avant de commencer à vous servir de la

calculatrice. Toutefois, après que vous aurez utilisé la calculatrice un certain temps,

l’impression deviendra graduellement plus pâle, ce qui indique que vous devez changer le

ruban. Pour ce faire, procédez comme suit :

1. Retirez le rouleau de papier après avoir coupé le papier à l’arrière de la

calculatrice. Appuyez sur la touche d’alimentation papier (↑) pour faire

avancer le restant du papier dans l’imprimante. Enlevez ensuite le couvercle

de l’imprimante.

2. Enlevez le vieux ruban en le tirant vers le haut (la figure 6 montre

l’imprimante sans ruban).

3. Installez la bobine de ruban en mettant le côté noir en haut. Victor

recommande d'utiliser le ruban Victor 7010 (fig. 5).

4. Sur la tige gauche, placez la bobine qui contient la plus grosse quantité de

ruban.

5. Ensuite, déroulez le ruban pour le faire passer à l’extérieur des guides et

devant la roue d’impression (fig. 7).

6. Faites tourner les bobines afin de tendre le ruban. Remettez le couvercle de

l’imprimante et le rouleau de papier.

(Remplacez par le ruban encreur Victor n

o

7010)

(Fig. 5) (Fig. 6)

(Fig. 7)

Disposition du clavier

La présente section décrit les interrupteurs de mode, les touches d’entrée de données et

les touches d’opération de votre calculatrice.

Caractéristiques des touches et des interrupteurs à glissière

OFF ON (marche / arrêt)

OFF Mise hors tension.

ON Mise sous tension.

P NP PC

P Mode impression : l’imprimante fonctionne constamment tant que la calculatrice

est sous tension.

NP Mode non-impression : l’imprimante est activée seulement lorsque vous

appuyez sur la touche d’alimentation papier ou sur la touche de non-addition/date

(#/S). Ce mode s’appelle aussi le mode affichage seulement.

PC Mode PC : ce mode permet à la calculatrice de transmettre à un ordinateur les

informations saisies, au lieu de les transmettre à l’imprimante. Le nombre saisi

apparaîtra dans la première colonne, et l'opération exécutée apparaîtra dans la

deuxième colonne. Ce mode s’appelle également le mode ruban virtuel.

• Le dispositif de transmission des données sans fil doit être installé dans un

port USB de l’ordinateur si vous désirez utiliser un des trois modes PC.

Dispositif de transmission des données sans fil (fig. 9)

▲ 5/4 ▼

▲ Mode arrondissement au nombre supérieur : avec le réglage ▲, le résultat

d’un calcul est arrondi automatiquement au nombre supérieur.

5/4 Mode arrondissement au plus près : avec ce réglage, le résultat est arrondi

automatiquement. Dans la réponse, si le premier chiffre après le réglage décimal

est entre 0 et 4 inclusivement, la valeur est arrondie au nombre inférieur; sinon, la

valeur est arrondie au nombre supérieur.

▼ Mode arrondissement au nombre inférieur : avec ce réglage, les calculs sont

arrondis automatiquement au nombre inférieur (la valeur est tronquée).

Σ • GT

Σ

Mode sigma :

lorsque l’interrupteur à glissière est réglé à la position sigma, le

résultat des multiplications ou des divisions est automatiquement ajouté à

l’accumulateur lorsque vous appuyez sur les touches = ou % après l'opération. Le

total accumulé peut être réaffiché en appuyant sur la touche T.

• La calculatrice n’utilise ni le mode sigma ni le mode total global.

GT Mode total global : tout total calculé au moyen de la touche T est

automatiquement ajouté à la mémoire. Le total global accumulé peut être

réaffiché en appuyant sur la touche MT.

A 0 2 3 F Kpad

A Mode ajout monétaire : lorsque ce réglage est utilisé, il est présumé que les

montants entrés sont des valeurs monétaires. La calculatrice insère

automatiquement un point décimal à la gauche des deux derniers chiffres entrés.

0 2 3 Modes décimales fixes : ces réglages indiquent combien de chiffres apparaîtront

à la droite du point décimal lors de l’affichage du résultat.

F Mode point décimal flottant : ce réglage indique que tous les chiffres du résultat

sont affichés, jusqu’à un maximum de 12 chiffres. Si le résultat dépasse cette

capacité, les chiffres en trop à la droite du point décimal sont tronqués. Aucun

arrondissement n’est fait.

Kpad Mode clavier : ce mode permet de se servir de la calculatrice comme d’un clavier

pour l’ordinateur de l’utilisateur. Chaque fois que vous appuyez sur une touche

numérique, l’entrée est immédiatement transmise à l’afficheur de l'ordinateur. La

touche T (total) sert de touche d’entrée, et les touches mémoire servent de touches

fléchées pour vous déplacer d’une cellule à l’autre dans un tableur.

• Le dispositif de transmission des données sans fil doit être installé dans un

port USB de l’ordinateur si vous désirez utiliser un des trois modes PC.

Page is loading ...

Victor 1280-7 Owner's manual

Victor 1280-7 Owner's manual

in other languages

Related papers

Other documents