®
The American Built-In Undercounter Leader Since 1962
U-LINE.COM
INSTALL GUIDE
3000 Series: Flange Kit Requirements and Instructions for Custom
36 inch and 90 cm Models
U-3000FLANGE-KIT-ICE U-3000FLANGE-KIT
THE MODULAR 3000 SERIES MODELS ARE INTENDED FOR BUILT IN INSTALLATIONS ONLY
U-Line Flange Kit Installation Guide 1
Safety Alert Definitions
Throughout this guide are safety items labeled with a Danger,
Warning or Caution based on the risk type:
DANGER
Danger means that failure to follow this safety statement will
result in severe personal injury or death.
WARNING
Warning means that failure to follow this safety
statement could result in serious personal injury,
property or equipment damage or death.
CAUTION
Caution means that failure to follow this safety statement
may result in minor or moderate personal injury, property
or equipment damage.
This guide covers the following kits:
U-3000FLANGE-KIT
U-3000FLANGE-KIT-ICE
IMPORTANTIMPORTANT
U-3000FLANGE-KIT is required when pairing (1) left-
hand and (1) right-hand 3018/3045 units OTHER THAN a
3018CLR/3045CLR.
U-3000FLANGE-KIT-ICE is required when paring (1) left-
hand 3018/3045 unit with (1) right-hand 3018CLR/
3045CLR.
Note: Use of the U-3000FLANGE-KIT-ICE requires that the 3018/
3045 Ice Machine MUST be a right-hand door swing (-00 model)
and installed on the right side only.
1 Safety Precautions 2 Guide Coverage
2 U-Line Flange Kit Installation Guide
Grille and Hardware Removal:
1. Loosen (2) 7/64" Allen wrench screws from the grille.
Figure 1 Grille Screw Locations
2. Slide grille forward, pushing tabs in, to remove grille.
Figure 2 Grille Removal
CAUTION
To avoid damage to the cord catcher, use care when
removing.
3. Pull down on the cord catcher to remove both the catcher and
its barbed push rivet.
Figure 3 Pulling Down on the Cord Catcher
3 Remove the Door and Frame
A
B
Cord Catcher
Barbed Push
Rivet
U-Line Flange Kit Installation Guide 3
4. Remove (2) hinge covers. Pushing top tab upward and bottom
tab downward, slide the cover off the hinge.
Figure 4 Hinge Cover Removal
Door Removal:
1. Loosen, but do not remove, the slotted hinge screw with a
T-25 Torx. (Slotted hinge screw is located closest to the unit
exterior.) Repeat for other hinge.
Figure 5 Removing Hinge Screws
2. Remove the non-slotted screw completely. (The non-slotted
screw is located closest to the unit interior.) Repeat for other
hinge.
3. Slide door so slotted hinges disengage.
CAUTION
To avoid damage to the unit, place the door near the unit.
The door is connected to the unit with a cord. Use care
when moving.
4. Place door by unit.
5. Completely remove (2) previously loosened slotted screws.
A
B
C
Bare Hinge
Hinge Screws (2)
4 U-Line Flange Kit Installation Guide
Middle Panel Removal
(U-3000FRAME-KIT-ICE ONLY):
1. Remove (2) cover screws.
Figure 6 Middle Panel Cover Screw Locations
2. Drill out (4) rivets with #30 (0.1285") drill bit.
Figure 7 Middle Panel Rivet Locations
3. Remove panel by pulling forward.
Frame Removal:
1. Drill out (2) rivets on opposite side from the hinge, which hold
the frame on. NOTE: Clear Ice unit will only have (1) rivet on
top flange.
Figure 8 Frame Rivet Locations
2. Remove frame by pulling forward.
3. Use these same instructions (3 – Remove the Door and Frame
starting on page
2
) to remove the door and frame of the other
unit.
Cover Screws (2)
Rivets (4)
U-Line Flange Kit Installation Guide 5
Positioning the Units:
CAUTION
Use caution when moving and handling the units. Use
gloves to prevent personal injury from sharp edges.
1. Place units side-by-side on a flat/level surface with leveling feet
retracted completely.
2. Ensure mating sides of the units are flush, and adjust feet to
maintain a constant gap between the units. NOTE: Use of a bar
clamp is recommended for best alignment.
Figure 9 Units Placed Side-by-Side
Installing “L”-Shaped Bracket:
1. Place steel bracket on units.
Figure 10 “L”-Shaped Bracket Placement
CAUTION
When drilling holes for the bracket, do not exceed the
maximum drill depth of 1/2" (12.7 mm).
2. Using the bracket as a template, drill (6) holes with a #30 drill
bit.
3. Install (6) Phillips sheet-metal screws supplied.
Preparing the Surfaces:
1. Wipe down unit to remove any grease that may prevent the
double sided tape (pre-installed) to adhere.
2. Peel back adhesive tape backing from Flange Kit.
Figure 11 Adhesive Tape
(U-3000FLANGE-KIT-ICE shown)
4 Install the 36" (90 cm) Frame
“L” Shaped bracket
Adhesive tape
6 U-Line Flange Kit Installation Guide
Frame Installation:
1. Rest the top of the frame on the (2) units. Align as required.
Figure 12 Sliding the Frame into Place
2. Slide the frame into place, working your way down.
3. Visually inspect the unit. Ensure the liner and the frame are flush
with one another.
Front Panel Installation
(U-3000FLANGE-KIT-ICE ONLY):
1. Locate (2) holes in the front of the frame.
Figure 13 Front Panel Screw Locations
CAUTION
When drilling holes for front panel, do not exceed the
maximum drill depth of 1/2" (12.7 mm).
2. Using the located holes as a template, drill (2) holes with a #30
drill bit.
3. Slide tongue (left side) of panel under the new frame and align
stamped holes with drilled holes.
4. Install (2) Phillips sheet-metal screws supplied.
Door Installation:
1. For the left door, install the (2) slotted hinge screws leaving
approximately a 5/32" (4 mm) gap between the frame and the
screw head.
2. Slide door so slotted hinges engage.
3. Install the (2) non-slotted hinge screws completely.
4. Tighten the (2) slotted hinge screws.
5. Repeat procedure for the right door.
6. Ensure proper alignment, fit and function.
Hardware Installation:
1. Install hinge covers. Slide cover onto the hinges, pinching the
top and bottom tabs together. A click can be heard when
seated properly.
2. Push the cord catchers and their barbed push rivets into place
using the supplied fasteners.
3. Ensure magnet/reed-switch alignment for doors.
Grille Installation:
1. Install front grilles. Pushing tabs in, slide each grille into its unit.
2. Tighten (2) 7/64" Allen wrench screws into each grille.
Screws (2)
5 Reinstall the Door, Hardware and
Grille
®
BUILDING ON THREE GENERATIONS OF INNOVATION
For nearly five decades and three generations, U-Line continues to be the leader in innovation, quality and value
in the premium built-in undercounter ice making, refrigeration and wine preservation market. U-Line has
captivated those with an appreciation for the finer things with exceptional functionality, style, inspired
innovation and attention to even the smallest details. We are known and respected for our unwavering
dedication to product design, quality and selection.
In 1962, Henry Uihlein founded U-Line Corporation as an outgrowth of Ben-Hur Freezer Company and was
the first to develop and patent an automatic stand-alone undercounter residential ice maker. His foresight and
determination to develop new ideas and to succeed when there were no clear guidelines or solutions are
evident today. The newest Uihlein generation continues to build upon the family’s innovative legacy at the
Milwaukee, Wisconsin based business by providing continuity and vision from which new designs and
technology continue to be born.
Today the complete U-Line product collection includes Ice Makers, Wine Captain® Models, Combo® Models,
a Refrigerator / Freezer, Refrigerators, Drawers and Beverage Centers. The U-Line brand offers products in the
1000 Series, 2000 Series and the Modular 3000 Series. The 1000 Series offers a more targeted priced product
with appropriate features, while the 2000 Series offers upscale features, advanced technology and specialized
product families. U-Line’s approach to its breadth of products, multiple price points and features allows a choice
and product that will fit any lifestyle.
DESIGNED, ENGINEERED AND ASSEMBLED IN WISCONSIN, USA
U-LINE.COM
GENERAL INQUIRIES:
U-Line Corporation
P.O. Box 245040
Milwaukee, Wisconsin 53224-9540 U.S.A.
Phone (414) 354-0300
FAX (414) 354-7905
Email: [email protected]
www.u-line.com
SERVICE ASSISTANCE:
Phone (800) 779-2547
FAX (414) 354-5696
Email: onlineser[email protected]
www.u-lineservice.com
PARTS ASSISTANCE:
E-mail: onlineparts@u-line.com
SERVICE INFORMATION
If you have a problem with this appliance, your use and care guide has troubleshooting information to help you
quickly identify common problems and provide information on possible cause and remedy. Answers to
Customers Frequently Asked Questions are available at www.u-line.com/customer/faq.cfm. You may contact
U-Line directly:
©2013 U-Line Corporation
Publication Number 30402 03/2013 Rev A
The American Built-In Undercounter Leader Since 1962
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
U-Line 1175BEVS13 Quick start guide
-
-
-
-
U-Line ULN-SS1095FD-03 Installation guide
-
-
U-Line U-3024RGLOL-00 Installation guide
-
-
-