Chicago Electric 69275 User manual

Brand: Chicago Electric

Model: 69275

Category: Power tools

Type: User manual

This manual is also suitable for

Saw 69275

Chicago Electric Saw 69275

The Chicago Electric Saw 69275 is a powerful and versatile saw that is perfect for a variety of cutting tasks. With its 2.5 horsepower motor, this saw can easily cut through even the toughest materials. The 10-inch industrial-grade blade provides precise cuts, and the adjustable blade guard ensures safety during operation. The Chicago Electric Saw 69275 is also equipped with a number of features that make it easy to use, including a built-in laser guide and a dust collection port.

Chicago Electric Saw 69275

Blade and stand sold separately.

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]

ITEM 69275

2.5 HORSEPOWER

10" INDUSTRIAL

TILE/BRICK SAW

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

2011 by Harbor Freight Tools

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-800-444-3353 as soon as possible.

Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,

inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual

near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and

the receipt in a safe and dry place for future reference.

Owner’s Manual & Safety Instructions

Page 2 For technical questions, please call 1-800-444-3353. Item 69275

SAFETY OPERATION MAINTENANCESETUP

Table of Contents

Safety ......................................................... 2

Specifications ............................................. 8

Setup .......................................................... 9

Operation ................................................... 12

Maintenance .............................................. 15

Parts Lists and Diagram ............................ 17

Warranty .................................................... 20

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

Page 3For technical questions, please call 1-800-444-3353.Item 69275

SAFETYOPERATIONMAINTENANCE SETUP

IMPORTANT SAFETY INFORMATION

General Tool Safety Warnings

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

1. KEEP GUARDS IN PLACE and in working order.

2. REMOVE ADJUSTING KEYS AND WRENCHES.

Form habit of checking to see that keys and adjusting

wrenches are removed from tool before turning it on.

3. KEEP WORK AREA CLEAN.

Cluttered areas and benches invite accidents.

4. DON’T USE IN DANGEROUS ENVIRONMENT.

Don’t use power tools in damp or wet locations,

or expose them to rain. Keep work area well lighted.

5. KEEP CHILDREN AWAY. All visitors should

be kept safe distance from work area.

6. MAKE WORKSHOP KID PROOF with padlocks,

master switches, or by removing starter keys.

7. DON’T FORCE TOOL. It will do the job better

and safer at the rate for which it was designed.

8. USE RIGHT TOOL. Don’t force tool or attachment

to do a job for which it was not designed.

Table A: RECOMMENDED MINIMUM WIRE

GAUGE FOR EXTENSION CORDS (120 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD

LENGTH

25′ 50′ 100′ 150′

0 – 6 18 16 16 14

6.1 – 10 18 16 14 12

10.1 – 12 16 16 14 12

12.1 – 16 14 12 Do not use.

9. USE PROPER EXTENSION CORD. Make sure your

extension cord is in good condition. When using

an extension cord, be sure to use one heavy

enough to carry the current your product will

draw. An undersized cord will cause a drop in line

voltage resulting in loss of power and overheating.

Table A shows the correct size to use depending

on cord length and nameplate ampere rating.

If in doubt, use the next heavier gauge.

The smaller the gauge number, the heavier the cord.

10. WEAR PROPER APPAREL. Do not wear

loose clothing, gloves, neckties, rings, bracelets,

or other jewelry which may get caught in moving

parts. Nonslip footwear is recommended.

Wear protective hair covering to contain long hair.

11. ALWAYS USE SAFETY GLASSES. Also use

face or dust mask if cutting operation is dusty.

Everyday eyeglasses only have impact resistant

lenses, they are NOT safety glasses.

12. SECURE WORK. Use clamps or a vise to hold

work when practical. It’s safer than using your

hand and it frees both hands to operate tool.

13. DON’T OVERREACH. Keep proper

footing and balance at all times.

14. MAINTAIN TOOLS WITH CARE. Keep tools sharp

and clean for best and safest performance. Follow

instructions for lubricating and changing accessories.

15. DISCONNECT TOOLS before servicing;

when changing accessories, such as

blades, bits, cutters, and the like.

16. REDUCE THE RISK OF UNINTENTIONAL

STARTING. Make sure switch is in

off position before plugging in.

17. USE RECOMMENDED ACCESSORIES.

Consult the owner’s manual for recommended

accessories. The use of improper accessories

may cause risk of injury to persons.

18. NEVER STAND ON TOOL. Serious injury

could occur if the tool is tipped or if the

cutting tool is unintentionally contacted.

19. CHECK DAMAGED PARTS. Before further use

of the tool, a guard or other part that is damaged

should be carefully checked to determine that

it will operate properly and perform its intended

function – check for alignment of moving parts,

binding of moving parts, breakage of parts,

mounting, and any other conditions that may

affect its operation. A guard or other part that is

damaged should be properly repaired or replaced.

20. DIRECTION OF FEED. Feed work into

a blade or cutter against the direction of

rotation of the blade or cutter only.

21. NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Don’t leave tool

until it comes to a complete stop.

Page 4 For technical questions, please call 1-800-444-3353. Item 69275

SAFETY OPERATION MAINTENANCESETUP

Grounding Instructions

TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION

READ AND FOLLOW THESE INSTRUCTIONS:

110-120 V~ Grounded Tools: Tools with Three Prong Plugs

1. In the event of a malfunction or breakdown,

grounding provides a path of least resistance for

electric current to reduce the risk of electric shock.

This tool is equipped with an electric cord having an

equipment-grounding conductor and a grounding

plug. The plug must be plugged into a matching

outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

2. Do not modify the plug provided – if it will

not fit the outlet, have the proper outlet

installed by a qualified electrician.

3. Improper connection of the equipment-grounding

conductor can result in a risk of electric shock.

The conductor with insulation having an outer

surface that is green with or without yellow

stripes is the equipment-grounding conductor.

If repair or replacement of the electric cord or

plug is necessary, do not connect the equipment-

grounding conductor to a live terminal.

4. Check with a qualified electrician or service

personnel if the grounding instructions are

not completely understood, or if in doubt as

to whether the tool is properly grounded.

5. Use only 3-wire extension cords that

have 3-prong grounding plugs and 3-pole

receptacles that accept the tool’s plug.

6. Repair or replace damaged or worn cord immediately.

Figure A: 125 V~ 3-Prong Plug and Outlet

(for up to 125 V~ and up to 15 A)

Grounding

7. This tool is intended for use on a circuit that has

an outlet that looks like the one illustrated above

in Figure A: 125 V~ 3-Prong Plug and Outlet.

The tool has a grounding plug

that looks like the plug illustrated above in

Figure A: 125 V~ 3-Prong Plug and Outlet.

8. The outlet must be properly installed and grounded

in accordance with all codes and ordinances.

9. Do not use an adapter to connect

this tool to a different outlet.

Page 5For technical questions, please call 1-800-444-3353.Item 69275

SAFETYOPERATIONMAINTENANCE SETUP

Tile Saw Safety Warnings

For Your Own Safety Read Instruction Manual Before Operating Saw

1. Wear eye protection.

2. Use saw-blade guard and spreader

for every operation for which it can be

used, including all through sawing.

3. Keep hands out of the line of saw blade.

4. Use an appropriate push-stick when required.

5. Know how to reduce risk of kickback.

6. Do not perform any operation freehand.

7. Never reach around or over saw blade.

8. Make sure the workpiece is supported at all

times while sawing. Use a roller stand (not

provided) with larger workpieces if necessary.

9. To properly understand all safety warnings, be familiar

with the following safety terms and equipment:

a. Featherboard – A block with “fingers” that hold

the workpiece against the fence while sawing.

b. Through-sawing – A cut made from one side of the

workpiece to the opposite side, without stopping.

c. Push-stick – A narrow strip of wood or other soft

material with a notch cut into one end and which

is used to push short pieces of material through

saws. It provides a safe distance between the

hands and the cutting tool. Must be narrower than

the cut width to prevent contact with the blade.

d. Freehand – Feeding a workpiece through the

saw without using a fence or guided support

to guide it. NOT A SAFE METHOD.

e. Kerf – The gap made by the saw in the workpiece.

f. Kickback – A sudden reaction to a pinched,

bound, or misaligned blade, causing

an uncontrolled workpiece to lift up and

out of the saw toward the operator.

g. Spreader – A metal plate that follows the

saw blade to keep the kerf (gap) from closing

on the saw blade. Spreaders, except riving

knives, must be aligned to the blade after

blade adjustment to prevent binding.

10. As noted previously, Kickback is a sudden reaction

to a pinched, bound, or misaligned blade, causing an

uncontrolled workpiece to lift up and out of the saw

toward the operator.

Kickback is usually a result of tool misuse and can be

limited or avoided by following the precautions below:

• Fence must be completely

parallel to the saw blade.

• Workpiece must be free from flaws

and from foreign objects.

• Support large workpieces along their

entire length. Large workpieces tend

to bend, grabbing the blade.

• Maintain control of the workpiece. Do not

allow the workpiece to rest against the

moving blade without holding onto it.

• If the blade binds or a cut is interrupted, turn

off the power switch and hold the workpiece

still until the blade stops. Correct the cause

of blade binding before proceeding.

11. Check guards for proper operation with saw

disconnected from power before each use.

Do not disable any guard. Do not operate

saw if any movable guard does not move

freely and close instantly. Make sure any

movable guard does not touch the blade in

all angles, depths of cut, and positions.

12. Keep the guard in place while through-

sawing. Verify that the spreader lines up

with the blade to prevent binding.

Page 6 For technical questions, please call 1-800-444-3353. Item 69275

SAFETY OPERATION MAINTENANCESETUP

POSITION OF TILE SAW

Figure B: Drip Loop

Power Cord

Tile Saw

Drip Loop

13. To avoid the possibility of the tool plug or

receptacle getting wet, position tile saw to one

side of a wall mounted receptacle to prevent

water from dripping onto the receptacle or plug.

The user should arrange a “drip loop” in the cord

connecting the saw to a receptacle. The “drip loop”

is that part of the cord below the level of the

receptacle, or the connector if an extension cord

is used, to prevent water traveling along the cord

and coming in contact with the receptacle.

14. If the plug or receptacle does get wet, DON’T unplug

the cord. Disconnect the fuse or circuit breaker

that supplies power to the tool. Then unplug and

examine for presence of water in the receptacle.

Figure C: Extension Cord Drip Loop

Power Cord

Extension

Cord

Tile Saw

Drip Loop

15. If an extension cord is used, the drip loop must be

before the cord connection and the extension cord

connection must be placed on an elevated surface.

EXTENSION CORDS

16. Use only extension cords that are intended for

outdoor use. These extension cords are identified

by a marking “Acceptable for use with outdoor

tools; store indoors while not in use.” Use only

extension cords having an electrical rating not

less than the rating of the product. Do not use

damaged extension cords. Examine extension

cord before using and replace if damaged.

Do not abuse extension cords and do not yank

on any cord to disconnect. Keep cord away

from heat and sharp edges. Always disconnect

the extension cord from the receptacle before

disconnecting the product from the extension cord.

17. WARNING – To reduce the risk of electrocution,

keep all connections dry and off the ground.

Do not touch plug with wet hands.

18. Ground Fault Circuit Interrupter (GFCI) protection

should be provided on the circuit(s) or outlet(s)

to be used for the tile saw. Receptacles are

available having built-in GFCI protection and

may be used for this measure of safety.

Tile Saw Safety Warnings (cont.)

Page 7For technical questions, please call 1-800-444-3353.Item 69275

SAFETYOPERATIONMAINTENANCE SETUP

ADDITIONAL TILE SAW SAFETY WARNINGS

19. DO NOT OPERATE WITH ANY GUARD DISABLED,

DAMAGED, OR REMOVED. Moving guards

must move freely and close instantly.

20. The use of accessories or attachments not

recommended by the manufacturer may

result in a risk of injury to persons.

21. When servicing use only identical replacement parts.

22. Do not depress the spindle lock when

starting or during operation.

23. Only use safety equipment that has been approved

by an appropriate standards agency. Unapproved

safety equipment may not provide adequate

protection. Eye protection must be ANSI-approved

and breathing protection must be NIOSH-approved

for the specific hazards in the work area.

24. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol or medication.

A moment of inattention while operating power

tools may result in serious personal injury.

25. Industrial applications must follow OSHA guidelines.

26. Maintain labels and nameplates on the tool.

These carry important safety information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

27. Avoid unintentional starting.

Prepare to begin work before turning on the tool.

28. People with pacemakers should consult their

physician(s) before use. Electromagnetic fields in

close proximity to heart pacemaker could cause

pacemaker interference or pacemaker failure.

29. WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities, contains chemicals known [to the State

of California] to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicals are:

•Leadfromlead-basedpaints

•Crystallinesilicafrombricksandcementorother

masonry products

•Arsenicandchromiumfrom

chemically treated lumber

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are

specially designed to filter out microscopic particles.

(California Health & Safety Code § 25249.5, et seq.)

30. WARNING: Handling the cord on this product will

expose you to lead, a chemical known to the State

of California to cause cancer, and birth defects or

other reproductive harm. Wash hands after handling.

(California Health & Safety Code § 25249.5, et seq.)

31. The warnings, precautions, and instructions

discussed in this instruction manual cannot

cover all possible conditions and situations

that may occur. It must be understood by the

operator that common sense and caution are

factors which cannot be built into this product,

but must be supplied by the operator.

Tile Saw Safety Warnings (cont.)

Page 8 For technical questions, please call 1-800-444-3353. Item 69275

SAFETY OPERATION MAINTENANCESETUP

Vibration Safety

This tool vibrates during use. Repeated or long-term

exposure to vibration may cause temporary or permanent

physical injury, particularly to the hands, arms and

shoulders. To reduce the risk of vibration-related injury:

1. Anyone using vibrating tools regularly or for an

extended period should first be examined by a

doctor and then have regular medical check-ups

to ensure medical problems are not being caused

or worsened from use. Pregnant women or

people who have impaired blood circulation to

the hand, past hand injuries, nervous system

disorders, diabetes, or Raynaud’s Disease should

not use this tool. If you feel any medical or

physical symptoms related to vibration (such as

tingling, numbness, and white or blue fingers),

seek medical advice as soon as possible.

2. Do not smoke during use. Nicotine reduces

the blood supply to the hands and fingers,

increasing the risk of vibration-related injury.

3. Use tools with the lowest vibration when there

is a choice between different processes.

4. Include vibration-free periods each day of work.

5. Grip tool as lightly as possible (while still keeping

safe control of it). Let the tool do the work.

6. To reduce vibration, maintain the tool as

explained in this manual. If any abnormal

vibration occurs, stop use immediately.

SAVE THESE INSTRUCTIONS.

Specifications

Electrical Rating 120V~ / 15A

Motor No Load Speed 3,800 RPM

Max. Blade Diameter 10″

Arbor Diameter 5/8″

Max. Cutting Depth

3-1/2″@0º

1-1/2″@45º

Max. Cutting Length 24″

Max Diagonal Tile Size 18″

Bevel Cutting Range 0º,22.5º,45º

Page 9For technical questions, please call 1-800-444-3353.Item 69275

SAFETYOPERATIONMAINTENANCE SETUP

Setup - Before Use:

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

Functions

Pump Outlet

Bevel Lock

Lever

Depth Stop

Water Tray

Frame

Stand

(sold separately)

Water

Tray

Table

Power

Switch

& Key

Reset

Button

Depth

Lock

Depth

Knob

Guard

Lock

Miter

Gauge

Table

Lock

Lever

Toggle

Table Stop

Table

Stop

Drain

Plug

Blade

(sold separately)

Pump

Bracket

Power

Cord

Pump

Power

Cord

Power Switch: The Power Switch includes a Key

for safety. The Tile Saw switch cannot be turned

on without the key. Remove the Key after use.

Reset Button: Directly above the Power Switch is

the Reset Button. If the Tile Saw overheats it will shut

down automatically. Allow it to cool down, make sure

there are no loose connections or damaged cords,

and then press the Reset Button to restart the Saw.

Do not force workpieces into the saw and make sure

the blade is properly wetted to reduce overheating.

Toggle Table Stop: This allows the Table to be

removed if needed. Lift the Stop and turn it to

lock/unlock. If the slot is aligned with the Table,

the Table can be removed. If the slot is turned

sideways, the Table is locked into the saw.

Table Lock Lever: To lock the Table in place, line up this

Lever′spinwiththeholeintherail,andpresstheLever

towards the rail. Pull out on the Lever to unlock the Table.

Page 10 For technical questions, please call 1-800-444-3353. Item 69275

SAFETY OPERATION MAINTENANCESETUP

ASSEMBLY

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Turn the Power Switch of the tool to its “OFF” position, remove the key, and unplug the tool

from its electrical outlet before assembling or making any adjustments to the tool.

Note: For additional information regarding the parts listed in the following pages,

refer to the Assembly Diagram near the end of this manual.

Installing the Water Tray Frame to the Leg Stand

1. Lock the Toggle Table Stop by pulling up on it

and turning it until the slot in the center of

the Stop is horizontal (left to right).

2. Pull the Table to the front of the Frame.

From under the right side of the Table, align the

hole in the rail with the pin in the Table Lock Lever.

Push the pin into the rail, locking the Table.

3. Align the holes on the Water Tray Frame with

the holes on the Stand (sold separately).

4. Insert Short Bolts through Washers

and into holes. Tighten securely.

Figure D: Water Tray Frame Installation

Stand

Water Tray

Frame

Washer

Short

Bolt

Installing Motor Head and Water Tray Frame

1. Install Handle to end of Water Tray Frame

using Bolts (119) and Washers.

2. Align the holes in the Motor Head assembly with

the holes on the side of the Water Tray Frame.

3. Insert two Short Bolts through Washers,

and then into holes on side of Motor Head.

Loosely secure using Lock Nuts.

4. Insert four Long Bolts through Lock Washers

and Washers. Insert into holes on end of

Water Tray Frame, as shown. Finger tighten.

5. Tighten all Bolts securely.

Figure E: Motor Head Installation

Motor

Head

Short

Bolt

Long

Bolt

Lock

Washer

Lock

Nut

Water

Tray Frame

Washer

Handle

Page 11For technical questions, please call 1-800-444-3353.Item 69275

SAFETYOPERATIONMAINTENANCE SETUP

Installing the Particle Tray

1. Unlock the Table Lock Lever. Lift and turn the

Toggle Table Stop so that its slot aligns with the Table.

2. Pull the Table to the front of the Water Tray Frame.

3. Slide the Particle Tray into the Grooves

on the underside of the Table.

4. Return the Table to its working position,

and lift then turn the Toggle Table Stop

so that its slot aligns sideways.

Figure F: Particle Tray

Particle Tray

Grooves

Table

Water Tray and Pump Setup

1. From the right side of the saw, place the

Water Tray (drain plug end to the left) on the

lip at the bottom of the Water Tray Frame.

2. Slide the Water Tray in under the Table

until it rests in place within the tabs.

3. Adjust the flow control on the

Pump to the desired level.

4. Place the Pump into the Pump Bracket in the

Pump Basin. It should fit securely into the Bracket.

5. Connect the clear water Hose from under the arm of

the Motor Head to the Hose Connector on the Pump.

6. Make sure your hands are dry and the Tile Saw

is unplugged, then attach the Pump Power

Cord to the Pump Outlet on the Motor Head.

7. Fill the Water Tray with clean water up to the

Fill Rim (see Figure H) before every use.

Figure G: Water Tray Installation

Water Tray

Frame

Figure H: Pump setup

Water

Tray

Drain Plug

Fill Rim

Pump

Basin

Pump

Power

Cord

Pump

Outlet

Hose Connector

Page 12 For technical questions, please call 1-800-444-3353. Item 69275

SAFETY OPERATION MAINTENANCESETUP

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

TOOL SET UP

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Turn the Power Switch of the tool to its “OFF” position, remove the key, and unplug the tool

from its electrical outlet before assembling or making any adjustments to the tool.

TO PREVENT SERIOUS INJURY:

DO NOT OPERATE WITH ANY GUARD DISABLED, DAMAGED, OR REMOVED.

Installing Blade

1. Unplug the saw.

2. Turn the Guard Knob counterclockwise.

3. Open the Guard to expose the Spindle.

4. Loosen the Spindle Nut counterclockwise

and remove the old Blade, if installed.

5. Place the Inner Flange onto the Spindle.

Install with the cupped side of the

Inner Flange facing the tile saw housing.

6. Wipe a drop of oil onto the Inner Flange

where it will contact the Blade.

WARNING! TO PREVENT SERIOUS INJURY:

Only use a smooth rim, wet cutting, 10″ Blade rated

to at least 3,800 RPM on this tool.

Do not use a Blade that is too thick to allow Outer Flange

to engage with the flats on the Spindle.

Do not use a Blade that has openings, grooves, or teeth.

7. Slide the Blade (sold separately) onto Spindle.

8. Place Outer Flange onto the Spindle.

The flats on the Outer Washer align with the

flats on the Spindle. Install with the cupped

side of the Outer Flange facing the blade.

9. Place Spindle Nut on Spindle.

10. Press and hold the Spindle Lock in.

11. Wrench-tighten Spindle Nut securely.

Release the Spindle Lock.

12. Close the Guard, and use the

Guard Knob to secure it.

Figure I: Blade Assembly

Inner

Flange

Blade

Outer

Flange

Spindle

Nut

Spindle

Lock

Wrench

Blade Guard

Guard

Knob

Figure J: Securing Blade

Page 13For technical questions, please call 1-800-444-3353.Item 69275

SAFETYOPERATIONMAINTENANCE SETUP

Miter Adjustment

Note: The Miter Gauge can be used from

either the left or the right side of the Blade.

1. Place the slot on the underside of the

Miter Gauge on the Table Fence.

2. Lock the Miter Gauge securely to the table by

turning the Gauge Lock Knob clockwise.

3. To adjust angles:

a. Loosen the Miter Lock Lever.

b. Set to the desired angle by moving

the Guide left or right.

c. Tighten the Miter Lock Lever securely

before turning on the saw.

Figure K: Miter Gauge

Miter Gauge

Miter Lock

Lever

Gauge

Lock

Knob

Table

Fence

Bevel Adjustment

1. Slide the Table clear of the Blade

to prevent blade damage.

2. Loosen the Bevel Lock Lever.

3. Adjust the Motor Head to the desired angle:

0º, 22.5º or 45º. Do not set bevel to

any other setting, the slots in the table

are designed only for these cuts.

4. Tighten the Bevel Lock Lever.

Figure L: Bevel Lock Lever

Bevel Lock

Lever

Depth Adjustment

1. Depth Lock: Use the Depth Lock to lock the

Motor Head in the down position; press it in while

the Motor Head is down to lock, and pull out

while holding down the Motor Head to unlock.

2. Depth Knob: The Depth Knob can be used to

lock the Motor Head at a particular cutting depth;

tighten it to lock the Motor Head in place,

loosen it to allow adjustment.

3. Depth Stop: This controls the maximum cut depth.

If the blade cuts too deeply or too shallowly;

loosen the Depth Stop Lock, adjust the Depth Stop,

and tighten the Depth Stop Lock again.

Figure M: Depth Controls

Depth Knob

Depth

Lock

Depth Stop Depth Stop

Lock

Work Piece and Work Area Set Up

1. Designate a work area that is clean and well-lit.

The work area must not allow access by children

or pets to prevent distraction and injury.

2. Route the power cord along a safe route to reach

the work area without creating a tripping hazard

or exposing the power cord to possible damage.

The power cord must reach the work area with

enough extra length to allow free movement

while working. Set up the Power Cord with a drip

loop, see Position of Tile Saw on page 6.

3. There must not be objects, such as utility lines,

nearby that will present a hazard while working.

4. Keep workpieces pressed firmly against

the Table and Fence while cutting.

5. Mark cut lines using waterproof marker or crayon.

Note: This tool is intended for use on

man-made masonry and tile products only.

Page 14 For technical questions, please call 1-800-444-3353. Item 69275

SAFETY OPERATION MAINTENANCESETUP

General Operating Instructions

1. Fill the Water Tray with clean water up to

the Fill Rim (see Figure H on page 11)

before every use.

CAUTION: Water level must be kept above lip

of pump basin at all times during operation.

2. Adjust the Miter, Bevel, and Depth

settings as needed, see previous page.

Lock all settings in place.

3. Place the workpiece on the Table and firmly

against the Miter Gauge and Fence.

4. Make sure the workpiece is clear of the Blade,

then dry your hands, plug in the Saw, insert the Key

and turn the Power Switch to the ON position.

5. Make sure the pump is supplying enough water

to the Blade. If needed, dry your hands, unplug

theSaw,adjustthePump′sflowcontrol,dry

your hands again, and plug the Saw back in.

6. Let the Blade build up to full speed before cutting.

7. Hold the material firmly against the rip guide

and feed the material into the Blade.

8. When the cut is made, turn the Saw OFF.

Wait for the Blade to come to a complete stop

before removing any part of the workpiece.

9. To prevent accidents, turn off the Saw, remove the

Key, and unplug the Tile Saw after use. Clean,

then store the Saw indoors out of children’s reach.

Figure N: Straight Cut

Figure O: Miter Cut

Figure P: Bevel Cut

Page 15For technical questions, please call 1-800-444-3353.Item 69275

SAFETYOPERATIONMAINTENANCE SETUP

Maintenance and Servicing

Procedures not specifically explained in this manual must

be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Turn the Power Switch of the tool to its “OFF” position, remove the key, and unplug the tool from

its electrical outlet before performing any inspection, maintenance, or cleaning procedures.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:

Do not use damaged equipment. If abnormal noise or vibration

occurs, have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication

1. BEFORE EACH USE, inspect the general condition

of the tool. Check for loose hardware, misalignment

or binding of moving parts, cracked or broken parts,

damaged electrical wiring, and any other

condition that may affect its safe operation.

2. AFTER USE, wipe external surfaces of the tool

with clean cloth. Also, clean the following after

every use, and as needed during extended use:

• Rails

• Particle Tray (see page 11)

• Water Tray (see page 11,

empty out sediment and water)

• Pump filter and housing (see page 11,

can often be rinsed off without opening pump).

3. If Blade is out of alignment, Table does not

slide smoothly or other issues interfere with

smooth operation, have the saw serviced by

a qualified technician before further use.

4. WARNING! If the supply cord of this

power tool is damaged, it must be replaced

only by a qualified service technician.

Page 16 For technical questions, please call 1-800-444-3353. Item 69275

SAFETY OPERATION MAINTENANCESETUP

Troubleshooting

Problem Possible Causes Likely Solutions

Tool will not start. 1. Cord not connected.

2. No power at outlet.

3. Tool’s thermal reset breaker tripped.

4. Internal damage or wear. (Carbon

brushes or switch, for example.)

1. Check that cord is plugged in.

2. Check power at outlet. If outlet is unpowered,

turn off tool and check circuit breaker.

If breaker is tripped, make sure circuit is right

capacity for tool and circuit has no other loads.

3. Turn off tool and allow to cool.

Press reset button on tool.

4. Have technician service tool.

Tool operates

slowly.

Extension cord too long or

wire size too small.

Eliminate use of extension cord.

If an extension cord is needed, use shorter/

heavier gauge cord. See Table A on page 3.

Performance

decreases

over time.

1. Blade dull or damaged.

2. Carbon brushes worn or damaged.

1. Keep cutting accessories sharp. Replace as needed.

2. Have qualified technician replace brushes.

Excessive noise

or rattling.

Internal damage or wear. (Carbon

brushes or bearings, for example.)

Have technician service tool.

Overheating. 1. Forcing machine to work too fast.

2. Blade misaligned.

3. Blade dull or damaged.

4. Blocked motor housing vents.

5. Motor being strained by long or

small diameter extension cord.

1. Allow machine to work at its own rate.

2. Check and correct Blade alignment to fence and table.

3. Keep cutting blades sharp. Replace as needed.

4. Wear ANSI-approved safety goggles and

NIOSH-approved dust mask/respirator while

blowing dust out of motor using compressed air.

5. Eliminate use of extension cord.

If an extension cord is needed, use shorter/

heavier gauge cord. See Table A on page 3.

Follow all safety precautions whenever diagnosing or servicing the tool.

Disconnect power supply before service.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

Page 17For technical questions, please call 1-800-444-3353.Item 69275

SAFETYOPERATIONMAINTENANCE SETUP

Part Description Size Qty

1 Cross Head Screw ST3.5×11 6

2 Press Plate 1

3 Guard Knob 1

4 Big Washer 5 5

5 Right Guard Cover 1

6 E-Clip 4 1

7 Guard Screw 1

8 Nut M16×1.5 1

9 Outer Flange 1

10 Blade (sold separately)

Ø254×15.9

11 Inner Flange 1

12 Outlet 1

13 Cross Head Screw ST3.5×6.5 3

14 Outlet Connector 1

15 Hose Cover 1

16 Bolt M5×14 7

17 Left Guard Cover 1

18 Splash Guard 1

19 Big Washer 4 4

20 Cross Head Screw ST4.2×13 6

21 Lower Handle Cover 1

22 Upper Handle Cover 1

23 Flat Washer 5 13

24 Cross Head Screw M5×50 4

25 Depth Stop 1

26 Depth Stop Lock 1

27 Spring Washer 5 3

28 Bearing Bracket 1

29 Bearing Screw 7

30 Bearing 6003 1

31 O Type Ring Ø50×2.65 1

32 C-Clip 20 2

33 Ring 1

34 Output Shaft 1

35 Gear 1

36 Key A6×10 2

37 Oilless Bushing 1

38 Shaft Lock Pin 1

39 Spring 1

40 Felted Wool Washer 1

41 Gear Box 1

42 Bearing 6202 1

43 Bolt M5×70 2

44 Stator 1

45 Bearing 6001 1

46 Pad 1

47 Strain Relief 1

48 Motor Inside Cord 1

49 Brush Cover 2

50 Carbon Brush 2

Part Description Size Qty

51 Brush Holder 2

52 Motor Housing 1

53 Set Screw M5×8 2

54 Hex Bolt M5×20 4

55 Rear Cover 1

56 Cross Head Screw ST4.2×9.5 4

57 Bevel Angle Plate 1

58 Bolt M6×12 4

59 Washer 8 4

60 Bevel Lock Lever 1

61 Cross Head Screw M4×14 10

62 Flat Washer 4 23

63 Arm Cover 1

64 Cross Head Screw M4×10 7

65 Spring Washer 4 5

66 Ground Terminal 4 2

67 Star Washer 4 2

68 Cord Clip 2

69 Bolt M5×12 2

70 Cord Strain Relief M20 1

71 Power Cord 1

72 Cord Clamp 1

73 Bolt M10×52 2

74 Flat Washer 10 6

75 Cord Strain Relief M16 1

76 Cord Protection Tube 1

77 Ext. Cord 1

78 Water Hose Ø6 1

79 Cord Protection Ring 3

80 Arm 1

81 Locknut M10 2

82 Cross Head Screw M4×35 4

83 Protection Sleeve 6.3 4

84 Pin 6.3 4

85 Power Switch & Key CB-8/B 1

86 Switch Bracket 1

87 Overload Switch SCP-15A 1

88 Set Screw M5×15 2

89 Shaft 2

90 Cord Clamp 1

91 Cross Head Screw M4×12 8

92 Terminal Box 1

93 Terminal Pole PA12 1

94 Cross Head Screw ST2.9×18 1

95 Depth Knob 1

96 Set Screw M5×8 2

97 Spring Insert 2

98 Torsion Spring 1

99 Angle Bracket 1

100 Nut M6 3

Parts Lists and Diagram

Main Parts List (parts 1-100)

Page 18 For technical questions, please call 1-800-444-3353. Item 69275

SAFETY OPERATION MAINTENANCESETUP

Part Description Size Qty

101 Bolt M6×20 2

102 Angle Pointer 1

103 O Type Ring Ø6.7×1.8 1

104 Depth Lock Pin 1

105 Depth Lock 1

106 Bolt M6×75 2

107 Front Limited Block 1

108 Locknut M6 5

109 Bolt M10×75 4

110 Spring Washer 10 4

111 Handle Asm. 1

112 Left Rail 1

113 Bolt Sleeve, B 4

114 Insert A 2

115 Insert B 2

116 Frame 1

117 Flat Washer 8 10

118 Cross Head Screw ST4.2×35 5

119 Bolt M8×40 2

120 Front Panel 1

121 Locknut M8 7

122 Back Limited Block 1

123 Press Spring, A 1

124 Limited Bolt 1

125 Right Rail 1

126 Bolt M8×65 8

127 Rubber Pad A 1

128 Rubber Pad B 2

129 Rubber Pad C 1

130 Rubber Pad I 1

131 Rubber Pad II 2

132 Rubber Pad III 1

133 Spring Washer 8 2

134 Bolt M8×30 2

135 Side Working Table 1

136 Bearing Screw, A 3

137 C-clip 22 6

Part Description Size Qty

138 Bearing 608-RS 9

139 Wheel A 3

140 Bearing Washer, A 2

141 Bolt Sleeve A 1

142 Eccentric Screw 3

143 Working Table 1

144 Wheel, B 3

145 Bearing Screw, C 1

146 Eccentric Screw, B 2

147 Bearing Washer, B 3

148 Pin Handle 1

149 Pin 1

150 Ball Ø4 1

151 Press Spring, B 1

152 Particle Tray 1

153 Set Screw (Glued) M6×8 1

154 Support Plate 1

155 Plate 1

156 Cross Head Bolt M6×10 1

157 Miter Lock Lever 1

158 Miter Lock Screw 1

159 Miter Gauge Screw 1

160 Miter Gauge 1

161 Ball Ø8 1

162 Press Spring, C 1

163 Gauge Lock Knob 1

164 Angle Plate 1

165 Clamp Plate 1

166 Chain Connector 1

167 Ring 2

168 Chain Asm. 1

169 Ring 1

170 Plug 1

171 Hose Ø8 1

172 Pump 1

173 Water Tray 1

Stand Parts List

Note: Stand sold separately.

Part Description Size Qty

1a Hex Bolt M8×55 2

2a Insert C 2

3a Bolt M8×20 2

4a Front Support Leg Asm. 1

5a Foot 2

6a Flat Washer 8 4

Part Description Size Qty

7a Locknut M8 2

8a Rear Support Leg Asm. 1

9a Flat Washer 12 2

10a Wheel 2

11a Flat Washer 10 2

12a Locknut M10 2

Main Parts List (continued, parts 101+)

Page 19For technical questions, please call 1-800-444-3353.Item 69275

SAFETYOPERATIONMAINTENANCE SETUP

Assembly Diagram

1a 2a

3a 2a

8a 6a

9a 10a 11a 12a

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,

and warrants to the original purchaser that this product is free from defects in materials and workmanship for the

period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries

to persons or property, or for incidental, contingent, special or consequential damages arising from the use of

our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may

elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will

return repaired products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

Chicago Electric 69275 User manual

Brand: Chicago Electric

Model: 69275

Category: Power tools

Type: User manual

This manual is also suitable for

Saw 69275

Chicago Electric Saw 69275

Download PDF

report

Chicago Electric 69275 User manual

This manual is also suitable for

Chicago Electric 69275 User manual

Related papers

Other documents