Panasonic TXP54Z11E Operating instructions

Category
Plasma TVs
Type
Operating instructions

This manual is also suitable for

TQB0E0888U-1
Operating Instructions
Plasma Television
Model No. TX-P46Z11E
TX-P54Z11E
Please read these instructions before operating your set and retain them for future reference.
The images shown in this manual are for illustrative purposes only.
Please refer to Pan European Guarantee Card if you need to contact your local Panasonic dealer for assistance.
English
2
Notice for DVB functions
Any functions related to DVB (Digital Video Broadcasting) will work in areas where
DVB-T (MPEG2 and MPEG4-AVC(H.264)) digital terrestrial broadcasting are
received, where DVB-C (MPEG2 and MPEG4-AVC
(H.264)) digital cable services
are supplied or where DVB-S (MPEG2 and MPEG4-AVC
(H.264)) digital satellite
broadcasting are received.
Consult your local dealer with coverage areas or your cable provider to access.
DVB functions may not be available in some countries or areas.
Some functions may not be available in some countries or areas.
Some functions may not be available with some cable provider.
Some functions may not be available with some satellites.
This TV has the capability for DVB specifications. But future DVB services cannot
be guaranteed.
Turn your own living room into a movie theatre!
Experience an amazing level of multi-
Viewing Advanced FAQs, etc.
Quick Start Guide
3
This product is licensed under the AVC patent portfolio
license for the personal and non-commercial use of a
consumer to (i) encode video in compliance with the AVC
Standard (“AVC Video”) and/or (ii) decode AVC Video that
was encoded by a consumer engaged in a personal and
non-commercial activity and/or was obtained from a video
provider licensed to provide AVC Video. No license is
granted or shall be implied for any other use.
Additional information may be obtained from MPEG LA, LLC.
See http://www.mpegla.com.
media excitement
Enjoy rich multi-media
Camcorder
Amplifier with
Speaker system
VCR
DVD player
DVD Recorder
Personal
computer
Set top box
SD Card
Up to 100,000 hours Plasma Panel Lifetime
The Plasma display panel used in the 2009 VIERA TV
range is rated for up to 100,000 hours.
This measurement is based on the time taken for the brightness of the
panel to reduce to half of it’s maximum level.
The time taken to reach this level may vary depending on the image
content and the environment where the TV is used.
Image retention and malfunctions are not taken into account.
Contents
Be Sure to Read
Safety Precautions ············································ 4
(Warning / Caution)
Notes
································································· 5
Maintenance
······················································ 6
Options
······························································ 6
Quick Start Guide
Accessories ·························
7
Basic Connection ·············· 12
Identifying Controls ············ 14
Auto Setup ························· 16
Enjoy your TV!
Basic Features
Watching TV ···················································· 18
Using TV Guide
··············································· 22
Viewing Teletext
··············································· 24
Watching External inputs
································· 26
How to Use Menu Functions
··························· 28
(picture, sound quality, etc.)
Advanced Features
Retuning from Setup Menu ····························· 36
Tuning and Editing Channels (DVB)
················ 40
Tuning and Editing Channels (Analogue)
········ 44
Child Lock
························································ 46
Using Common Interface
································· 47
Shipping Condition
·········································· 48
Updating the TV Software
······························· 49
Input Labels
····················································· 50
Multi Window
··················································· 51
Using MHP Services
········································ 52
Displaying PC Screen on TV
··························· 54
How to Use VIERA TOOLS
····························· 55
Using Network Services
·································· 56
(DLNA / VIERA CAST)
Viewing from SD Card
····································· 64
(VIERA IMAGE VIEWER)
Link Functions
················································ 68
(Q-Link / VIERA Link)
External Equipment
········································· 76
FAQs, etc.
Technical Information ······································ 78
FAQs
······························································· 85
Licence
···························································· 89
Specifications
·················································· 90
4
Safety Precautions
Warning
Handling the mains plug and lead
Insert the mains plug fully into the socket outlet. (If the mains plug is loose, it could generate heat and cause
fire.)
Ensure that the mains plug is easily accessible.
Ensure the earth pin on the mains plug is securely connected to prevent electrical shock.
An apparatus with CLASS I construction shall be connected to a mains socket outlet with a protective
earthing connection.
Do not touch the mains plug with a wet hand. (This may cause electrical shock.)
Do not damage the mains lead. (A damaged lead may cause fire or electrical shock.)
Do not move the unit with the lead plugged in the socket outlet.
Do not place a heavy object on the lead or place the lead near a high-temperature object.
Do not twist the lead, bend it excessively, or stretch it.
Do not pull on the lead. Hold onto the mains plug body when disconnecting lead.
Do not use a damaged mains plug or socket outlet.
If you find any
abnormality,
remove the mains plug
immediately!
AC 220-240 V
50 / 60 Hz
Power source
This TV is designed to operate on 220-240 V,
50 / 60 Hz AC.
Do not remove covers
NEVER modify the unit yourself
(High-voltage components may cause serious
electrical shock.)
Do not remove the rear cover as live parts are
accessible when it is removed. There are no user
serviceable parts inside.
Have the unit checked, adjusted, or repaired at your
local Panasonic dealer.
Do not expose to rain or
excessive moisture
To prevent damage which might result in electric
shock or fire, do not expose the unit to rain or
excessive moisture. The unit must not be exposed
to dripping or splashing water and objects filled with
liquid, such as vases, must not be placed on top of
or above the unit.
Do not expose to direct sunlight
and other sources of heat
Avoid exposing the unit to direct sunlight and other
sources of heat. To prevent fire never place any type
of candle or naked flame on top or near the unit.
Do not place foreign objects
inside the unit
Do not allow any objects to drop into the unit
through the air vents (fire or electrical shock may
result).
Do not place the unit on sloped
or unstable surfaces
The unit may fall off or tip over.
Use only the dedicated
pedestals / mounting equipment
Using an unapproved pedestal or other fixtures may
make the Display Unit unstable, risking injury. Be
sure to ask your local Panasonic dealer to perform
setup.
Use approved pedestals / mounts (p. 6).
Do not allow children to handle
SD Card
As with a small object, SD Card can be swallowed
by young children. Please remove SD Card
immediately after use.
5
Notes
Do not display a still picture
for a long time
This causes the image to remain on the
plasma screen (“image retention”).
This is not considered a malfunction and is
not covered by the warranty.
Typical still images
Channel number and
other logos
Image displayed in
4:3 mode
Video game
Computer image
To prevent image retention, contrast is
lowered automatically after a few minutes
if no signals are sent or no operations are
performed. (p. 85)
Auto power standby function
If no signal is received and no operation
is performed in Analogue TV mode for
30 minutes, the unit will automatically go
to standby mode.
The unit will automatically go to Standby
mode if there are no signal and no
operation between the Display Unit and
the Tuner Box for a while.
Tuner Box - after 1 minute
Display Unit - after 10 minutes
Keep the unit away from these
types of equipment
Electronic equipment
In particular, do not place video equipment
near the unit (electromagnetic interference
may distort images / sound).
Equipment with an infrared sensor
This unit also emits infrared rays (this may
affect operation of other equipment).
Adjust the panel to your desired
angle (TX-P46Z11E)
Ensure that the pedestal does not hang
over the edge of the base even if the TV
swivels to the full rotation range.
Do not place any objects or hands within
the full rotation range.
10˚ 10˚
(View from the top)
500 mm
383 mm
Set the mark at the centre as
illustrated, to ensure full degree
rotation in either direction.
When cleaning the unit, remove the mains plug
Cleaning an energized unit may cause electrical shock.
When the unit is not going to be used for a
long period of time, remove the mains plug
The unit will still consume some power even in the Off mode,
as long as the mains plug is still connected to a live socket
outlet.
Transport only in upright position
Transporting the Display Unit with its display panel facing
upright or downward may cause damage to the internal
circuitry.
Allow sufficient space around the Display
Unit for radiated heat
Minimum distance
10
10
10
3
(cm)
When using the pedestal, keep the space between the
bottom of the Display Unit and the surface where the Display
Unit is set.
In case of using Wall-hanging bracket, follow the manual of
it.
Do not block the rear air vents
Blocked ventilation by newspapers, table cloths, curtains,
etc. may cause overheating, fire or electrical shock.
Do not expose your ears to excessive
volume from the headphones
Irreversible damage can be caused.
The Display Unit is heavy. Handle the
Display Unit by 2 or more people. Support
as shown to avoid injury by the Display Unit
tipping or falling.
Caution
6
Maintenance
Options
First, remove the mains plug from the socket outlet.
Display panel
Regular care: Gently wipe the surface clean of dirt by using a soft cloth.
Major contamination: Wipe the surface clean using a soft cloth dampened with clean water or diluted neutral
detergent (1 part detergent to 100 parts water). Then, using a soft dry cloth, evenly wipe the surface clean until it is
dry.
Caution
The surface of the display panel has been specially treated and may be easily damaged.
Do not tap or scratch the surface with your fingernail or other hard object.
Take care not to subject the surface to insect repellent, solvent, thinner, or other volatile substances (this may
degrade surface quality).
Cabinet, Pedestal, Tuner Box
Regular care: Wipe the surface clean using a soft dry cloth.
Major contamination: Dampen a soft cloth with clean water or water containing a small amount of neutral detergent.
Then, wring the cloth and wipe the surface clean with it. Finally, wipe the surface clean with a dry cloth.
Caution
Take care not to subject the unit’s surfaces to detergent. (A liquid inside the unit could lead to product failure.)
Take care not to subject surfaces to insect repellent, solvent, thinner, or other volatile substances (this may
deteriorate the surface by peeling the paint).
Do not allow the cabinet and pedestal to make contact with a rubber or PVC substance for a long time.
Mains plug
Wipe the mains plug with a dry cloth at regular intervals. (Moisture and dust may lead to fire or electrical shock.)
Optional accessories
Wall-hanging bracket
TY-WK5P1SW
Please contact your nearest Panasonic dealer to purchase the recommended
wall-hanging bracket. For additional details, please refer to the wall-hanging
bracket installation manual.
Rear of the Display Unit
Holes for wall-hanging
bracket installation
a
b
TX-P46Z11E
a: 472 mm / b: 300 mm
TX-P54Z11E
a: 516 mm / b: 300 mm
Caution
In order to maintain the unit’s performance and safety, be absolutely sure to ask your dealer or a licenced
contractor to secure the wall-hanging brackets.
Carefully read the instructions accompanying optional accessories, and be absolutely sure to take steps to
prevent the Display Unit from tipping over.
Handle the Display Unit carefully during installation since subjecting it to impact or other forces may cause
product damage.
Take care when fixing wall brackets to the wall. Always ensure that there are no electrical cables or pipes in
the wall before hanging bracket.
To prevent fall and injury, remove the Display Unit from its fixed wall position when it is no longer in use.
Accessories
Maintenance ●●Options
Quick Start Guide
7
Accessories
Pedestal
p. 8
Pedestal installation kit
p. 8
(2)
(4)
(4)
Speaker (2)
p. 10
Standard accessories
Check that you have the accessories and items shown
Display Unit
Remote Control
N2QAYB000353
abc def
jkl
ghi
mno
tuvpqrs
wxyz
Batteries for the
Remote Control (2)
R6 (UM3)
Cleaning cloth
Clamper (2)
p. 14
Tuner Box
p. 12
Ferrite core (2)
p. 77
Use the Ferrite cores to
comply with the EMC
standard.
HDMI cable
p. 12
Speaker installation kit
p. 10
(8) (8)
Operating Instructions
Pan European Guarantee Card
This product contains possibly dangerous parts (such as plastic bags), that can be breathed in or swallowed by
young children accidentally. Keep these parts out of reach of young children.
8
Accessories
Installing / removing remote’s batteries
1
Pull
open
Hook
2
Note the correct
polarity (+ or -)
Close
Caution
Incorrect installation may cause battery leakage and corrosion, resulting in damage to the remote control.
Do not mix old and new batteries.
Do not mix different battery types (such as alkaline and manganese batteries).
Do not use rechargeable (Ni-Cd) batteries.
Do not burn or breakup batteries.
Batteries must not be exposed to excessive heat such as sunshine, fire or the like.
Do not disassemble or modify the remote control.
Attaching the pedestal
Warning
Do not disassemble or modify the pedestal.
Otherwise the Display Unit may fall over and become damaged, and personal injury may result.
Caution
Do not use any other TV and displays.
Otherwise the TV may fall over and become damaged, and personal injury may result.
Do not use the pedestal if it becomes warped or physically damaged.
If you use the pedestal while it is physically damaged, personal injury may result. Contact your nearest Panasonic
dealer immediately.
During set-up, make sure that all screws are securely tightened.
If insufficient care is taken to ensure screws are properly tightened during assembly, the pedestal will not be
strong enough to support the Display Unit, and it might fall over and become damaged, and personal injury may
result.
Ensure that the Display Unit does not fall over.
If the Display Unit is knocked or children climb onto the pedestal with the Display Unit installed, the Display Unit
may fall over and personal injury may result.
Two or more people are required to install and remove the Display Unit.
If two or more people are not present, the Display Unit may be dropped, and personal injury may result.
Pedestal
TBLX0105 (TX-P46Z11E)
TBLX0107 (TX-P54Z11E)
Base
TBLA0421 (TX-P46Z11E)
TBLA0460 (TX-P54Z11E)
Frame
TBLA0462 (TX-P46Z11E)
TBLA0464 (TX-P54Z11E)
Pedestal installation kit
TXFEL01DMUB TXFBL01JUUJ
Assembly screw (2)
(Silver)
XYN8+F30FN
Assembly screw (4)
(Black)
XSB4+10FNK
Assembly screw (4)
(Black)
THEL062N
M8 × 30 M4 × 10 M5 × 25
Holder cover
TBLB3416
Accessories
Quick Start Guide
9
Assembling the pedestal
Remove the Cable cover from the Frame .
Cable cover will be used again after the
pedestal is attached to the Display Unit.
B
Cable cover
Use the assembly screws to fasten securely.
Make sure that the screws are securely tightened.
Be careful not to scratch the surface (part with gloss finish) of the base during assembly.
A
A
B
B
C
Hole for the
Base installation
Securing the Display Unit
Slide the pedestal frame posts into the brackets on
the rear of the Display Unit.
Use the assembly screws to fasten securely.
Make sure that the screws are securely tightened.
E
Attach the Holder cover with assembly screws .
Make sure that the screws are securely tightened.
D
F
Attach the Cable cover.
Cable cover
Place a cable in
the groove as
necessary and
attach the Cable
cover.
The lower part
of the groove is
separated in right
and left. Use the
one suitable for
you.
10
Accessories
Attaching the Speakers
Speaker
SP-46Z1E (TX-P46Z11E)
SP-54Z1E (TX-P54Z11E)
Speaker (2)
Speaker installation kit
TXFKR01JXUE
Mounting bracket-[Top] (2)
TXFKR04DLUJ
Mounting bracket-[Lower right]
TXFKR02JXUE
Mounting bracket-[Lower left]
TXFKR03JXUE
hook
hook
Assembly screw
TXFXY01DLUJB
Speaker cable (2)
TXJ/SPDKUU-1
(8)
(8)
Use the assembly screws - to fasten the Mounting
brackets to the rear of the Display Unit securely.
Make sure that the screws are securely tightened.
Note
Loosen these screws to
adjust the gap between the
Speaker and the Display Unit
as necessary.
C
-
E-a
B
Ensure that the silver
part is facing the front
Display Unit
Insert the assembly screws - temporarily in the
screw outermost holes of the Speaker and place
the temporarily inserted screws into the counter sunk
holes on the Mounting brackets .
A
C
B
E-- b
Accessories
Quick Start Guide
11
Use another two assembly screws - to fasten the
Speaker to the Mounting brackets .
C
A
B
E-- b
Adjust the speaker position and make sure that the
assembly screws - are securely tightened.
E b
Connect the Speaker and the Display Unit with the
Speaker Cable
.
Insert the terminal firmly.
Connect the terminal near the Ferrite core to the Display
Unit.
Fix the cable with the clamper on the Mounting bracket
.
F
A
C
Push here to
remove the hook
hook
Fix the cable
Display Unit
clamper
Ferrite core
terminal
Note
Fix the other side speaker in the same way.
There will be a gap between the Display Unit and the Speaker.
Do not hold the Speaker part to transport the Display Unit.
12
Basic Connection
Connecting the Display Unit and the Tuner Box
Please ensure that the unit is disconnected from the mains socket before attaching or disconnecting any
leads.
Tuner Box
TU-Z100E
HDMI cable
K1HY19YY0004
AUDIO
IN
COMPONENT
AUDIO
OUT
DIGITAL
AUDIO OUT
HDMI 1
P
B
Y
P
R
L
R
L
R
HDMI 2 HDMI 3
A
B
Rear of the Display Unit
Rear of the Tuner Box
This terminal is not used
for this model.
Mains lead
AC 220-240 V
50 / 60 Hz
Mains
lead
Tuner Box
or
K1HY19YY0006
HDMI cable
3.0 m
Connecting the Tuner Box and dish / aerial / external equipment
External equipment and cables shown are not supplied with this TV.
Please ensure that the unit is disconnected from the mains socket before attaching or disconnecting any
leads.
Read the manual of the equipment too.
Example 1
Connecting dish or aerial (TV only)
AV 2
AV 1
AUDIO
IN
COMPONENT
AUDIO
OUT
DIGITAL
AUDIO OUT
HDMI 1
RGB
VIDEO
S VIDEO
RGB
VIDEO
P
B
Y
P
R
L
R
L
R
HDMI 2 HDMI 3
Rear of the Tuner Box
RF
cable
Terrestrial
aerial
For digital cable,
digital terrestrial
and analogue
broadcasts
Mains lead
AC 220-240 V
50 / 60 Hz
Satellite
dish
Satellite
cable
For digital satellite
broadcasts
Cable
Selectable satellites and dish alignment to tune DVB-S channels:
Turksat at 42° East
Hellas at 39° East
Astra at 28.2° East
Arabsat at 26° East
Astra at 23.5° East
Astra at 19.2° East
Eutelsat at 16° East
Hot Bird at 13° East
Eutelsat at 10° East
Eurobird at 9° East
Eutelsat at 7° East
Sirius at 5° East
Intelsat at 1° West
Amos at 4° West
Atl. Bird at 5° West
Atl. Bird at 7° West
Atl. Bird at 8° West
Hispasat at 30° West
To ensure your satellite dish is correctly installed, please consult your local dealer.
Also please consult the received satellite broadcasting companies for details.
Basic Connection
Quick Start Guide
13
Example 3
Connecting DVD Recorder / VCR and Set top box
RF OUT
RF IN
AV 2
AV 1
AUDIO
IN
COMPONENT
AUDIO
OUT
DIGITAL
AUDIO OUT
HDMI 1
RGB
VIDEO
S VIDEO
RGB
VIDEO
P
B
Y
P
R
L
R
L
R
HDMI 2 HDMI 3
DVD Recorder or
VCR
Fully wired
SCART cable
RF cable
RF cable
Fully wired HDMI
compliant cable
Set top box
Cable
Rear of the Tuner Box
Terrestrial
aerial
Mains lead
AC 220-240 V
50 / 60 Hz
Connect to the TV’s AV1 / AV2 for a DVD Recorder / VCR supporting Q-Link (p. 70).
Example 2
Connecting DVD Recorder / VCR
RF OUT
RF IN
AV 2
AV 1
AUDIO
IN
COMPONENT
AUDIO
OUT
DIGITAL
AUDIO OUT
HDMI 1
RGB
VIDEO
S VIDEO
RGB
VIDEO
P
B
Y
P
R
L
R
L
R
HDMI 2 HDMI 3
RF cable
RF cable
Fully wired
SCART cable
DVD Recorder or VCR
Rear of the Tuner Box
Terrestrial
aerial
Mains lead
AC 220-240 V
50 / 60 Hz
Cable
Connect to the TV’s AV1 / AV2 for a DVD Recorder / VCR supporting Q-Link (p. 70).
Note
For HDMI-compatible equipment, possible to connect to HDMI terminals (HDMI1 / HDMI2 / HDMI3 / HDMI4) by
using HDMI cable (p. 76).
Network connection p. 57
Q-Link connection p. 68
VIERA Link connection p. 68 and p. 69
HDMI 4
AV3
L
V
S-V
PC AUDIO
via AV3
R
PC
14
Identifying Controls
Identifying Controls
Display Unit
Tuner Box
Remote control signal receiver
Do not place any objects between the TV remote control signal receiver and remote control.
Function select
Volume / Contrast / Brightness /
Colour / Sharpness /
Tint (NTSC mode) / Bass / Treble /
Balance / Auto Setup (p. 36, 38, 39)
Recording LED
Standby for Direct TV Recording: orange
Power LED
Standby: red
On: green
When using the remote control, indicates
the TV has received a command.
Power LED
Standby: red
On: green
Mains power On / Off switch
Turn the Display Unit On or Off.
When turning Off the Display Unit,
Tuner Box will also be turned to
Standby mode after 1 min.
Standby switch
Turn the Tuner
Box on or off to
standby mode
Selects channel in sequence
Changes the input mode
HDMI4 terminal
(p. 76)
SD Card slot
(p. 64)
AV3 terminals
(p. 76)
Headphones jack
(p. 76)
PC terminal
(p. 76)
Selects channel in sequence
Volume Up / Down
C.A.T.S. (Contrast Automatic Tracking System) sensor
Senses brightness to adjust picture quality when
“Eco Mode” in the Picture Menu is set to “On” (p. 30)
Using the clamper
Fix cables with clampers as necessary.
When using the optional accessory, follow the option’s
assembly manual to fix cables.
Rear of the Display Unit
snaps
To loosen:
Keep
pushing both
side snaps
Set the
tip in the
hooks
Insert the clamper
in a hole
Attach the clamper Bundle the cables
Keep
pushing
the knob
knob
hooks
To remove from the TV:
hole
Basic Connection
Identifying Controls
Basic Connection
Quick Start Guide
EXIT
ASPECT
OPTION
TEXT
REC
PROGRAMME
STTL
INDEX HOLD
BACK/
RETURN
MENU
INPUT
TV
G
U
I
D
E
V
I
E
R
A
T
O
O
L
S
V
I
E
R
A
L
i
n
k
DVD/VCR
TV
AVTV
abc def
jkl
ghi
mno
tuvpqrs
wxyz
DIRECT TV REC
15
Remote Control
Cursor buttons
Makes selections and adjustments
Standby On / Off switch
Switches TV On or Off standby
Sound Mute
Switches sound mute On or Off
Aspect (p. 20)
Changes aspect ratio from Aspect Selection
list
Also possible by pressing this button
repeatedly until you reach the desired aspect
Channel Up / Down
Selects channel in sequence
Connected equipment operations
(p. 27 and p. 74)
Teletext (p. 24)
Switches to teletext mode
OK
Confirms selections and choices
Press after selecting channel positions
to quickly change channel
Volume Up / Down
Channel / Programme Information
(p. 19)
Displays channel and programme
information
Index (p. 25)
Returns to the teletext index page
(teletext mode)
Coloured buttons
Used for the selection, navigation and
operation of various functions
Exit
Returns to the normal viewing screen
Numeric buttons
Changes channel and teletext pages
Sets characters
When in Standby mode, switches TV On
VIERA Link Menu (p. 72)
Accesses VIERA Link Menu
Guide (p. 22)
Displays TV Guide
Option Menu (p. 21)
Easy setting for viewing and
sound options
Main Menu (p. 28)
Press to access Picture, Sound and
Setup Menus
Subtitles (p. 20)
Displays subtitles
Input mode selection
TV - switches DVB-S / DVB-C / DVB-T /
Analogue mode (p. 18)
AV - switches to AV input mode from Input
Selection list (p. 26)
VIERA IMAGE VIEWER (p. 64)
Switches to SD Card viewing mode
Return
Returns to the previous menu / page
Hold
Freeze / unfreeze picture (p. 19)
Holds the current teletext page (teletext
mode) (p. 24)
VIERA CAST (p. 63)
Displays VIERA CAST home screen
Direct TV Recording (p. 70 and p. 72)
Records programme immediately in
DVD Recorder / VCR with Q-Link or
VIERA Link connection
Surround (p. 31)
Switches Surround sound
VIERA TOOLS (p. 55)
Displays some special feature icons and
accesses easily
Identifying Controls
DIRECT TV REC
N
ASPECT
INPUT
AVTV
OPTION
TEXT
REC
PROGRAMME
STTL
INDEX HOLD
G
U
I
D
E
V
I
E
R
A
T
O
O
L
S
DVD/VCR
TV
EXIT
BACK/
RETURN
MENU
TV
16
Auto Setup
Search and store TV channels automatically.
These steps are not necessary if the setup has been completed by your local dealer.
Please complete preparations and setup of all units before starting Auto Setup. (p. 8 - 12)
Please complete connections (p. 12 and p. 13) and settings (if necessary) of the connected equipment before
starting Auto Setup. For details of settings for the connected equipment, read the manual of the equipment.
1
Plug the Display Unit and Tuner Box into
mains socket, and then turn the Display Unit on
Takes a few seconds to be displayed.
2
Select the language
Menüsprache
Nederlands
Português
Español
Italiano
Français
English
Deutsch
Latviešu
Slovenščina
Hrvatski
Lietuvių
eesti keel
Srpski
Românǎ
Български
Slovenčina
Magyar
čeština
Polski
Еλληνικά
Türkçe
Suomi
Norsk
Svenska
Dansk
select
set
3
Select your country
Country
Italy
France
Austria
Germany
Hungary
Czech
Slovakia
Poland
Finland
Norway
Sweden
Denmark
Malta
Switzerland
Portugal
Spain
Slovenia
Lithuania
Estonia
E.Eu
Turkey
Andorra Greece
Netherlands
Belgium
Luxembourg
select
set
Auto Setup starts
Auto Setup will start to search for TV
channels and store them.
The sorted channel order depends upon
the TV signal, the broadcasting system and
reception conditions.
Sending Preset Data
Please wait!
Remote control unavailable
0% 100%
If Q-Link, VIERA Link or similar technology
(p. 70) compatible recorder is connected,
channel, language, country / region
settings are automatically downloaded to
the recorder.
If downloading has failed, you can
download later by the menu item.
“Download” (p. 32)
4
Select “Home”
Please select your viewing environment.
Home Shop
set
select
Auto Setup is now complete and your TV is ready for viewing.
To check channel list at-a-glance
“Using TV Guide” (p. 22 and p. 23)
To edit channels
“Tuning and Editing Channels” (p. 40 - 45)
Auto Setup
Quick Start Guide
17
Using the On Screen Displays
Many features available on this TV can be accessed via the On Screen Display menu.
How to use remote control
Move the cursor / select the menu item
Move the cursor / adjust levels / select from
a range of options
Access the menu / store settings after
adjustments have been made or options
have been set
BACK/
RETURN
Return to the previous menu
MENU
Open the main menu
EXIT
Exit the menu system and return to the
normal viewing screen
ON SCREEN HELP Instructions box - Operation guide
(example: Sound Menu)
Select
EXIT
Change
RETURN
Mode Music
Bass
Treble
Balance
Headphone Volume
Surround Off
Volume Correction
Speaker Distance to Wall
Over 30cm
MPX Stereo
Sound Menu 1/2
Stereo
Page up
Page down
0
0
0
11
0
Operation guide will help you.
Auto Setup varies depending on the country you select
Depending on the country you select, you may be required to select the Favourite Network or Region.
Search Mode
(
if you select “Germany”,
“Austria”, “Switzerland”,
“Sweden” or “Finland”
)
Search Mode
All Channels Free Channels
select mode
set
DVB-S Auto Setup
(if you select “Germany”, “Austria” or “Switzerland”)
DVB-S Auto Setup
Analogue Scan 21 68
Satellite
Searching Satellite
This will take up to 15 minutes.
Satellite
Analogue Scan 68
Progress
Checking LNB2
0 100%
Press EXIT to skip Satellite installation
Astra 19.2°E
Hot Bird 13°E
DVB-S Auto Setup
Analogue Scan 21 68
No. Channel Name Type Quality
Searching Satellite
This will take about 30 minutes.
Satellite
Analogue Scan 68
Progress
Checking LNB1
0100%
Free TV: 3 Pay TV: 0 Radio: 0
372 CBBC Channel Free TV 10
372 BBC Radio Wales Free TV 10
372 E4 Free TV 10
Satellite Search:
If you have only one LNB (not having
DiSEqC control antenna system), you
can skip this step by pressing the EXIT
button.
Analogue Auto Setup DVB-T Auto Setup
(
if you select a country
except “Portugal”, “Poland”,
“Hungary” and “E.Eu”
)
DVB-C Auto Setup
(
if you select
“Sweden” or “Finland”
)
Auto Setup - DVB-T and Analogue
CH Channel Name Type Quality
Searching
This will take about 6 minutes.
Free TV: 4 Pay TV: 0 Radio: 0 Data: 0
Analogue Scan CH 2 CC 21 4199
DVB-T Scan CH 5 69
Analogue: 2
62 CBBC Channel Free TV 10
62 BBC Radio Wales Free TV 10
62 E4 Free TV 10
62 Cartoon Nwk Free TV 10
29 Analogue
-
33 BBC1 Analogue
-
Auto Setup - DVB-T and Analogue
CH Channel Name Type Quality
Searching
This will take about 6 minutes.
Free TV: 4 Pay TV: 0 Radio: 0 Data: 0
Analogue Scan CH 2 CC 21 4199
DVB-T Scan CH 5 69
Analogue: 0
62 CBBC Channel Free TV 10
62 BBC Radio Wales Free TV 10
62 E4 Free TV 10
62 Cartoon Nwk Free TV 10
DVB-C Auto Setup
Analogue Scan 21 68
No. Channel Name Type Quality
Searching
This will take about 3 minutes.
Progress 0% 100%
Free TV: 3 Pay TV: 0 Radio: 0 Data: 0
1 CBBC Channel Free TV 10
2 BBC Radio Wales Free TV 10
3E4 Free TV10
If you select “Shop” by mistake
Return to viewing environment selection by
pressing the RETURN button.
Select “Home”
Auto Setup is complete
Automatic Demo
Off On
BACK/
RETURN
Please select your viewing environment.
Home Shop
If you set to “Off” or “On” in this menu the
TV will be in “Shop” viewing environment.
To return to “Home” viewing environment
initialise all settings by accessing
Shipping Condition.
“Shipping Condition” (p. 48)
select
set
Note
If tuning has failed “Auto Setup” (p. 36 - 39)
To initialize all settings “Shipping Condition” (p. 48)
If you turned the Display Unit Off during Standby mode last time, the Display Unit will be in Standby mode when
you turn it On with Mains power On / Off switch.
N
V
I
E
R
A
T
O
O
L
S
BACK/
RETURN
TEXT
INDEX
REC
PROGRAMME
DVD/VCR
TV
EXIT
ASPECT
OPTION
STTL
HOLD
MENU
INPUT
TV
TV
abc def
jkl
ghi
mno
tuvpqrs
wxyz
18
Watching TV
Select a channel using Information banner (p. 19)
Possible to confirm the channel name and programme before changing channels.
Display Information banner if it is
not displayed
While the banner is displayed,
select the channel
select channel
watch
Possible to set display timeout in
“Banner Display Timeout” (p. 34).
Select a channel using TV Guide (p. 22)
Possible to confirm the TV Guide (EPG or Channel List) before changing channels.
This function may not be available in some countries.
Display TV Guide Select the channel
G
U
I
D
E
select
watch
Volume
1
Turn power on
(Press for about 1 second)
Mains power On / Off switch of the Display Unit should be On.
(p. 14)
2
Select the mode
TV Selection
DVB-C
DVB-S
DVB-T
Analogue
TV
watch
select
The selectable modes vary depending on the country you select (p. 16).
If “TV Selection” menu is not displayed, press the TV button to switch the
mode.
1 BBC ONE WALES
20:35
Coronation Street
20 : 00 - 20 : 55
Now
For info press
Change category
All DVB-T Channels
Information banner appears whenever you select a
channel
For details p. 19
Also possible to select the mode pressing the TV button repeatedly on the
remote control or front of the Tuner Box. (p. 14)
3
Select a channel
up
down
or
abc def
jkl
ghi
mno
tuvpqrs
wxyz
To select a more than two-digit channel
position number, e.g. 399
def
wxyz
wxyz
To select from the Channel List
All DVB-T Channels
Cartoon Nwk
BBC Radio Wales
BBC ONE Wales
BBC Radio Cymru
BBC THREE
BBCi
CBBC Channel
6
7
1
8
2
3
4
watch
select channel
Note
To watch pay-TV
“Using Common
Interface”
(p. 47)
Watching TV
Viewing
19
Hold
Freeze / unfreeze picture
HOLD
Display Information banner
1 ZDF
20:35Radio
Coronation Street
20 : 00 - 20 : 55
Now
For info press
Change category
All DVB-T Channels
45
Encrypted Dolby D +
Category
To change the category
blue
Channel type (if it is Radio or Data channel)
Channel position and name
Programme
Example (DVB):
Programme Start / Finish time
Features available / Message meanings
Current time
Display Information banner
Also appears when changing a channel
Encrypted
SubtitlesAD
Radio
For info press
3 ITV
19:35
itv1
All Analogue Channels
CH23
Stereo 45
Example (Analogue):
Channel number
Sound mute On
Bad signal
Poor TV signal quality
Encrypted
Scrambled programme
Dolby D +, Dolby D
Dolby Digital Plus or Dolby Digital audio track
Subtitle service available
Teletext service available
Multiple audio available
Multiple video available
MHP service available
Stereo, Mono
Audio mode
1 - 90
Off Timer remaining time
For settings
p. 21
To confirm another tuned
channel name
To watch the channel listed in the banner
Information on the next programme
(DVB)
To hide
EXIT
Extra information
(DVB) (press again to hide the banner)
To set display timeout
“Banner Display Timeout” (p. 34)
Other useful functions
20
Watching TV
Other useful functions
Display subtitles
Display / hide subtitles (if available)
To change the language for DVB (if available)
“Preferred Subtitles” (p. 34)
STTL
Note
If you press the STTL button in Analogue mode, it switches to teletext service and calls up a favourite page
(p. 25). Press the EXIT button to return to TV mode.
Aspect
Change the aspect ratio (image size)
ASPECT
Enjoy viewing the image at its optimum size and aspect.
Normally programmes have the Aspect Control Signal (Widescreen signal, etc.), and the TV will choose the
aspect ratio automatically according to the Aspect Control Signal (p. 78).
If you would like to change the aspect ratio manually
Display Aspect Selection list While the list is displayed, select the mode
ASPECT
Select
Change
EXIT
RETURN
Aspect selection
16:9
Just
14:9
4:3 Full
4:3
Zoom1
Zoom2
Zoom3
Auto
Aspect Selection list
store
select
To change the mode using the ASPECT button only
ASPECT
(Press repeatedly until you reach the desired mode)
Auto
The best ratio is chosen and the image expanded to fill the screen.
For details
p. 78
16:9 4:3 Full
Directly displays the image at 16:9
without distortion (anamorphic).
Displays a 4:3 image enlarged
horizontally to fit the screen.
HD signal only
14:9 Zoom1
Displays the image at the standard 14:9
without distortion.
Displays a 16:9 letterbox or 4:3 image
without distortion.
Just Zoom2
Displays a 4:3 image full-screen.
Stretching is only noticeable at the left
and right edges.
Displays a 16:9 letterbox (anamorphic)
image full-screen without distortion.
4:3 Zoom3
Displays the image at the standard 4:3
without distortion.
Displays a 2.35:1 letterbox (anamorphic)
image full-screen without distortion. At
16:9, displays the image at its maximum
(with slight enlargement).
Note
Only “16:9” and “4:3 Full” are available in HD channels.
Only “16:9” and “4:3” are available in PC input mode.
Not available when the subtitle function is active.
Not available in teletext service.
Aspect mode can be memorized separately for SD (Standard definition) and HD (High definition) signals.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92

Panasonic TXP54Z11E Operating instructions

Category
Plasma TVs
Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI