Philips GC1121/02 User manual

Brand: Philips

Model: GC1121/02

Category: Steam ironing stations

Type: User manual

www.philips.com

Comfort

GC1121, GC1120, GC1115, GC1111, GC1110,

GC1015, GC1011, GC1010

1 2 3 4

5 6 7 8

9 10 11 12

13 14 15

ENGLISH

General description

A Spray nozzle (GC1121/1120/1115/1015)

B Filling opening

C Spray button T (GC1121/1120/1115/1015)

D Steam control

- O = no steam

- q = moderate steam

- w = maximum steam

- x = Calc-Clean function

E Extra-steam function (press steam control) (GC1121/1120)

F Temperature dial

G Temperature light

H Cord

I Type plate

J Water tank

Important

Read these instructions for use carefully before using the appliance and

save them for future reference.

◗ Check if the voltage indicated on the type plate corresponds to the

local mains voltage before you connect the appliance.

◗ Only connect the appliance to an earthed wall socket.

◗ Do not use the appliance if the plug, the cord or the appliance itself

shows visible damage, or if the appliance has been dropped or is

leaking.

◗ Check the cord regularly for possible damage.

◗ If the mains cord is damaged, always have it replaced by one of the

original type in order to avoid a hazard.

◗ Never leave the appliance unattended when it is connected to the

mains.

◗ Never immerse the iron and the stand, if provided, in water.

◗ Keep the appliance out of the reach of children.

◗ The soleplate of the iron can become extremely hot and may cause

burns if touched.

◗ Do not allow the cord to come into contact with the soleplate when

it is hot.

◗ When you have finished ironing, when you clean the appliance, when

you fill or empty the water tank and also when you leave the iron

even for a short while: set the steam control to position O, put the

iron on its heel and remove the mains plug from the wall socket.

◗ Always place and use the iron and the stand, if provided, on a stable,

level and horizontal surface.

◗ Do not put perfume, vinegar, starch, descaling agents, ironing aids or

other chemicals in the water tank.

◗ This appliance is intended for household use only.

Before first use

1 Remove any sticker or protective foil from the soleplate.

2 Let the iron heat up to maximum temperature and pass the iron

over a piece of damp cloth for several minutes to remove any

residues from the soleplate.

The iron may give off some smoke when you use it for the first time. This

will cease after a short while.

Preparing for use

Filling the water tank

Never immerse the iron in water.

1 Make sure the appliance is unplugged.

2 Set the steam control to position O (= no steam) (fig. 1).

3 Tilt the iron backwards.

4 Fill the water tank with tap water up to the maximum level (fig. 2).

Do not fill the water tank beyond the MAX indication.

◗ If the tap water in your area is very hard, we advise you to mix it

with an equal amount of distilled water or to use distilled water

only.

Setting the temperature

1 Put the iron on its heel.

2 Set the required ironing temperature by turning the temperature dial

to the appropriate position (fig. 3).

Check the laundry care label for the required ironing temperature:

1 Synthetic fabrics (e.g. acrylic, viscose, polyamide, polyester)

1 Silk

2 Wool

3 Cotton, linen

If you do not know what kind or kinds of fabic an article is made of, deter-

mine the right ironing temperature by ironing a part that will not be visible

when you wear or use the article.

Silk, woollen and synthetic materials; iron the reverse side of the fabric to

prevent shiny patches. Avoid using the spray function to prevent stains.

Start ironing the articles that require the lowest ironing temperature, such

as those made of synthetic fibers.

3 Put the mains plug in an earthed wall socket.

4 When the temperature light has gone out, wait a while before you

start ironing (fig. 4).

The temperature light will go on from time to time during ironing.

Using the appliance

Steam ironing

1 Make sure that there is enough water in the water tank.

2 Select the recommended ironing temperature (see chapter

'Preparing for use', section 'Setting the temperature').

3 After the temperature light has gone out, set the steam control to

the appropriate steam position. Make sure that the steam setting

you select is suitable for the ironing temperature selected: (fig. 5).

q for moderate steam (temperature settings 2 to 3)

w for maximum steam (temperature settings 3 to MAX)

The iron will start steaming as soon as the set temperature has been

reached.

Ironing without steam

1 Set the steam control to position O (= no steam).

2 Select the recommended ironing temperature (see chapter

'Preparing for use', section 'Setting the temperature').

Features

Spray function (GC1121/1120/1115/1015 only)

You can use the spray function to remove stubborn creases at any temper-

ature.

1 Make sure that there is enough water in the water tank.

2 Press the spray button several times to moisten the article to be

ironed (fig. 6).

Extra steam (GC1121/1120 only)

This function provides extra steam to remove very stubborn creases.

◗ The extra-steam function only works at temperature settings

between 3 and MAX.

1 Set the steam control to position w (= maximum steam) (fig. 7).

2 Press and hold the steam control for a maximum of 5 seconds

(fig. 8).

3 Release the steam control and wait at least 1 minute before using

this function again to prevent water from dripping out of the sole-

plate.

Cleaning and maintenance

After ironing

1 Remove the mains plug from the wall socket and let the iron cool

down.

Comfort

4239 000 52292

2/12

ENGLISH

2 Wipe scale and any other deposits off the soleplate with a damp

cloth and a non-abrasive (liquid) cleaner.

To keep the soleplate smooth, you should avoid hard contact with metal

objects. Never use a scouring pad, vinegar or other chemicals to clean

the soleplate.

3 Clean the upper part of the appliance with a damp cloth.

4 Regularly rinse the water tank with water. Empty the water tank

after cleaning.

Calc-Clean function

Use the Calc-Clean function once every two weeks. If the water in your

area is very hard (i.e. when flakes come out of the soleplate during ironing),

the Calc-Clean function should be used more frequently.

1 Set the steam control to position O.

2 Set the temperature dial to MAX.

3 Fill the water tank to the maximum level.

Do not pour vinegar or other descaling agents into the water tank..

4 Put the plug in the wall socket.

5 Unplug the iron when the temperature light has gone out.

6 Hold the iron over the sink and set the steam control to the

Calc-Clean position x (fig. 9).

7 Pull the steam control slightly upwards and gently shake the iron

until all water in the tank has been used up.

Steam and boiling water will come out of the soleplate. Scale (if any) will

be flushed out.

8 After having used the Calc-Clean function, press the steam control

back to its original position and set it to position O.

Repeat the Calc-Clean process if the water coming out of the iron still

contains scale particles.

After the Calc-Clean process

1 Connect the iron to the mains to let the soleplate dry.

2 Unplug the iron when the temperature light has gone out.

3 Move the iron gently over a piece of used cloth to remove any

water stains that may have formed on the soleplate.

4 Let the iron cool down before you store it.

Cleaning the steam control needle

1 Pull the steam control out of the appliance (fig. 10).

2 Use vinegar to remove scale, if any, from the needle (fig. 11).

Do not bend or damage the steam control needle.

3 Reinsert the steam control needle by placing the point of the needle

exactly in the centre of the hole and by fitting the small projection

on the side of the needle into the slot (fig. 12).

4 Set the steam control to position O.

Storage

1 Make sure the appliance is unplugged and set the steam control to

position O.

2 Empty the water tank (fig. 13).

3 Wind the mains cord around the cord storage facility.

4 Store the iron on its heel in a safe and dry place (fig. 14).

Environment

◗ Do not throw the appliance away with the normal household waste

at the end of its life, but hand it in at an official collection point for

recycling. By doing this you will help to preserve the environment

(fig. 15).

Guarantee & service

If you need information or if you have a problem, please visit the Philips

website at www.philips.com or contact the Philips Customer Care Centre

in your country (you will find its phone number in the worldwide guaran-

tee leaflet). If there is no Customer Care Centre in your country, turn to

your local Philips dealer or contact the Service Department of Philips

Domestic Appliances and Personal Care BV.

Troubleshooting

This chapter summarises the most common problems you could encounter

with your iron. Please read the different sections for more details. If you

are unable to solve the problem, contact the Customer Care Centre in

your country.

Solution(s)

Check if the plug is connected

to the wall socket properly.

Set the temperature control dial

to the required temperature.

Fill the water tank (see 'Filling

the water tank').

Set the steam control dial to

position q or w (see 'Steam

ironing').

Set the temperature control dial

to a temperature suitable for

steam ironing (2 to MAX).

Put the iron on its heel and wait

until the pilot light has gone out

before you start ironing.

Press and hold the steam

control dial for maximal 5

seconds.

Wait at least 1 minute before

using the Extra Steam function

again.

Set the temperature control dial

to a temperature between 3

and MAX. Put the iron on its

heel and wait until the pilot light

has gone out.

Fill the water tank (see 'Filling

the water tank').

Set the temperature control dial

to a temperature between 3

and MAX. Put the iron on its

heel and wait until the pilot light

has gone out.

Wait at least 1 minute before

using the Extra Steam function

again (see 'Extra Steam').

Fill the water tank (see 'Filling

the water tank').

Use the Calc-Clean function a

few times (see 'Calc-Clean').

Set the temperature control dial

to a temperature suitable for

steam ironing (2 to MAX).

Put the iron on its heel and wait

until the pilot light has gone out

before you start ironing.

Empty the water tank and set

the steam control to position O

before storing the iron (see

'Storage'). Place the iron on its

heel.

Possible cause(s)

There is a connection

problem.

The temperature

control dial has been

set to MIN.

There is not enough

water in the water tank.

The steam control dial

has been set to position

The iron is not hot

enough.

The steam control dial

has not been pressed

long enough.

The Extra Steam

function has been used

too often in a short

period.

The iron is not hot

enough.

There is not enough

water in the water tank.

The iron is not hot

enough.

The Extra Steam

function has been used

too often in a short

period.

There is not enough

water in the water tank.

You have been using

hard water, which has

caused scale flakes to

develop inside the

soleplate.

The set temperature is

too low.

The iron has been put

in horizontal position

while there is still water

in the water tank.

Problem

The iron is plugged in

but the soleplate is

cold.

The iron does not

produce any steam.

The Extra Steam

function does not work

(types GC1121 and

GC1120)

Water leaks from the

soleplate when I use

the Extra Steam

function (types

GC1121 and GC1120)

The spray function does

not work (types

GC1121, GC1120,

GC1115 and GC1015)

Flakes and impurities

come out of the

soleplate during ironing.

Water leaks from the

soleplate during ironing.

Water leaks from the

soleplate while the iron

is cooling down or after

it has been stored.

Comfort

4239 000 52292

3/12

Page is loading ...

Philips GC1121/02 User manual

Brand: Philips

Model: GC1121/02

Category: Steam ironing stations

Type: User manual

Download PDF

report

in other languages

français: Philips GC1121/02 Manuel utilisateur
Deutsch: Philips GC1121/02 Benutzerhandbuch
Nederlands: Philips GC1121/02 Handleiding

Philips GC1121/02 User manual

Philips GC1121/02 User manual

in other languages

Related papers

Other documents