SOYO Atlas DYLT032C Owner's manual

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

LCD TV

OWNER'S MANUAL

IMPORTANT:

The serial number of this product may be found on the back

of the unit. You should record the number and other vital

information here and retain this manual as a permanent record

of your purchase to aid identification in case of theft. Serial

numbers are not kept on file.

IMPORTANT INFORMATION

The lightning flash with arrowhead symbol, within an equilateral

traingle, is intended to alert the user to the presence of uninsulated

"dangerous voltage”within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The exclamation point within a triangle is intended to alert the user to the

presence of important operating and maintenance(servicing)instruction

accompanying the product.

DYLT032D

1

ENGLISH

Model No:DYLT032D

Serial No:

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This product utilizes tin-lead solder, and flourescent lamp containing a small amount of

mercury. Disposal of these materials may be regulated due to environmental

considerations, For disposal or recycling information, please contact your local

authorities .

IMPORTANT INFORMATION(Continued)

WARNING: FCC Regulations state that any unauthorized changes or modifications to this

equipment not expressly approved by the manufacturer could void the user's

authority to operate this equipment.

CAUTION :TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLAND OF PLUG TO WIDE SLOT,

FULLY INSERT.

"Note to CATV SYSTEM installer, This reminder is provided to call CATV system installer's

attention to Article 820-40 of the National Electrical Code that provides guidelines for proper

grounding and, in particular, specifies that the cable ground has; be connected to the grounding

system of the buliding,as close to the point of cable entry as practical."

2

SERVICE INSTRUCTIONS:

No user-serviceable parts inside, refer servicing to qualfied service personnel.

Call 1-800-287-4871 to find the nearest service center.

ENGLISH

IMPORTANT SAFETY PRECAUTIONS

3

Electricity is used to perform many useful functions, but it can also cause personal injuries and property

damage if improperly handled .This product has been engineered and manufactured with safety being the

highest priority .However, improper use can result in personal injury and / or property

damage.

Read instructions - All operting instructions must be read and understood before the product is operated.

Keep this manual in a safe place - These safety and operating instructions must be kept in a safe place for future reference.

Observe warnings - All warnings on the product and in the instructions must be observed closely.

Follow instructions - All operating instructions must be followed.

Attachments - Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result in

accidents.

Power source - This product must be operated on a power source specified on the specification label. If you are not sure of

the type of power supply used in your home, consult your dealer or local power company. For units designed to operate on

batteries or another power source, refer to the operating instructions.

Power cord protection - The power cords must be routed properly to prevent people from stepping on them or objects from

resting on them.

If the AC adapter is misplaced or needs to be replaced,obtain the same type of adapter from our service center or your dealer.

Overloading - Do not overload AC outlets or extension cords, overloading can cause fire or electric shock.

Entering of objects and liquids - Never insert an object into the product through vents or openings. High voltage flows through

the product. Inserting objects can cause electric shock and/or short circuit internal parts. Also, do not spill water, or any other

Liquid on the product.

Servicing - Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other

dangerous conditions. Request a qualified service person to perform servicing.

Repair - If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified service

person to perform repairs.

a. When the power cord or plug is damaged.

b. When a liquid was spilled on the product or when objects have fallen into the product.

c. When the product has been exposed to rain or water.

d. When the product does not operate properly as described in the operating instructions.

Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls not

described in the instructions can cause damage,which often requires extensive adjustment work by a qualified technician.

e. When the product has been dropped or damaged.

f. When the product displays an abnormal picture.

g. Any noticeable abnormality in the product.

Replacement parts - In case the product needs replacement parts, make sure that the service person uses replacement parts

specified by the manufacturer.

Safety check - Upon completion of service or repair work, request the service technician to perform safety check to ensure

that the product is in proper operating condition.

Wall or ceiling mounting - When mounting the product on a wall or ceiling, be sure to install the product according to the

method recommended by the manufacturer.

Polarization - This AC adapter may be equipped with a polarized alternating current line plug (a plug having one blade wider

than the other).This plug will fit into the power outlet only one way .

This is a safety feature, If you are unable to insert the plug fully into the outlet, try reversing the plug, If the plug still doesn't fit

,contact your electrician to replace your obsolete outlet.

Do not defeat the safety purpose of the polarized plug.

ENGLISH

4

IMPORTANT SAFETY PRECAUTIONS(Continued)

Cleaning - Unplug the power cord from the AC outlet before

cleaning the product. Use a damp cloth to clean the product.

Do not use liquid cleaners or aerosol Cleaners.

Water and moisture - Do not use the product near water, such as

bathtub , washbasin,kitchen sink and laundry tub, swimming pool

and in a wet basement.

Stand - Do not place the product on an unstable cart, stand,

tripod or table. Placing the product on an unstable base can

cause the product to fall, resulting in serious personal injuries

as well as damage to the product. Use only a cart, stand, tripod,

bracket or table recommended by the manufacturer's

instruction. Use only the mounting hardware recommended by

the manufacturer.

When relocating the product, place it on a cart. It must be moved

with utmost care. Sudden stops, excessive force and uneven floor

surface can cause the product to fall from the cart.

Ventilation - The vents and other openings in the cabinet are

designed for ventilation. Do not cover or block these vents and

openings since insufficient ventilation can cause overheatings

and/or shorten the life of the product. Do not place the product

on a bed, sofa, rug or other similar surface, since they can

block ventilation openings. This product is not designed for built-in

installations; do not place the product in an enclosed place such as a

bookcase or rack, unless proper ventilation is provided or the

manufacturer's instruction are followed.

The Liquid Crystal panel used in this product is made of glass ,

Therefore ,it can break when the product is dropped or when

pressure is applied. Be careful not to injure yourself from broken

glass in case the Liquid Crystal Panel breaks.

Heat sources - Keep the product away from heat sources such

as radiators, heaters, stoves and other heat-generating products

(including amplifiers).

ENGLISH

5

If an outside antenna is connected to the television equipment, be sure the antenna system is

grounded so as to provide some protection against voltage surges and built-up static charges.

Section 810 of the Nation Electrical Code provides information with respect to proper

grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna

discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to

grounding electrode, and requirement for the grounding electrode.

Lightning - For added protection for this television equipment

during a lightning storm, or when it is left unattended and

unused for long period of time, unplug it from the wall outlet

and disconnect the antenna. This will prevent damage to the

equipment due to lightning and power-line surge.

IMPORTANT SAFETY PRECAUTIONS(Continued)

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTROCE SYSTEM

(NEC ART 250,PART H)

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

Power Lines - An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from touching

such power lines or circuits as contact with them might be fatal.

To prevent fire, never place any type of candle or naked

flames on the top or near the TV set.

To prevent fire or shock hazard,do not expose this products

to dripping or splashing.No objects filled with liquids, such

as vases, should be placed on the products.

ENGLISH

6

CONTENTS

IMPORTANT INFORMATION..............................................................................

IMPORTANT SAFETY PRECAUTIONS...............................................................

CONTENTS......................................................................................................

SUPPLIED ACCESSORIES................................................................................

PREPARATION.................................................................................................

REMOTE CONTROL OVERVIEW........................................................................

PDPTV CONTROLS OVERVIEW........................................................................

CONNECTORS OVERVIEW...............................................................................

BASIC OPERATION..........................................................................................

SELECTING MENU ITEMS.................................................................................

ADJUSTMENTS ...............................................................................................

CONNECTING EXTERNAL DEVICES................................................................

TROUBLESHOOTING.......................................................................................

SPECIFICATIONS.............................................................................................

Page

1-2

3-5

6

7

8-11

12-13

14

15

16-17

18

19-27

35

36-38

39

ENGLISH

SUPPLIED ACCESSORIES

Make sure the following accessories are included in the product packaging.

7

ENGLISH

Remote Control

Instruction Manual

AC cord

2 X"AAA" Size Batteries

OK

MUTEMTS

POWER

BRIGHT

ZOOM

VOL CH

1 2

3

4

5

6

7 8 9

0

DISPLAY YPbPr

SCREEN SIZE

SWAP

PIP ON

-

SLEEP

RECALL

MENU

ENTER

EXIT

SOURCE

MULTI-PIP

FREEZEPARENTALCC

PREPARATION

Using the Remote Control

Cautions regarding use of the remote control

Do not expose the remote control to shock.

In addition, do not expose the remote control to liquid, and do not place in an area with high

humidity.

Do not install or place the remote control under direct sunlight. The heat may cause deformation

of the unit.

The remote control may not work properly if the remote control sensor window of the main unit is

under direct sunlight or strong lighting. In such case, change the angle of the lighting or PDP

TV set, or operate the remote control closer to the remote control sensor window.

Installing the Batteries

Before using the PDP TV set for the first time, insert 2 "AAA" size batteries into the remote control

(supplied). When the batteries become depleted and the remote control fails to operate, replace

the batteries with new (AAA size) batteries.

Cautions regarding batteries

Improper use of batteries can result in chemical leakage and/or explosion. Be sure to follow the

instructions below:

Insert batteries with their terminals corresponding to the (+) and (-) as indicated in the compartment.

Different types of batteries have different characteristics. Do not mix batteries of different types.

Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries

and/or cause the old battery to leak .

Remove batteries when they become weak. Chemicals that leak from batteries can cause a rash.

If chemical leakage is found, wipe clean with cloth.

The batteries supplied with the product may have a shorter life expectancy due to storage

conditions.

If the remote control will not be used for an extended period of time, remove the batteries from the

remote control.

Caution!

8

Power on LED

Use the remote control by pointing it towards the remote control sensor window on the main unit.

Objects between the remote control and sensor window may prevent proper operation.

ENGLISH

1. Press cover edge & pull it to

open the battery cover.

3. Press the battery cover

down.

2. Insert both batteries noting

the polarity markings.

OK

MUTEMTS

POWER

BRIGHT

ZOOM

VOL CH

1

2

3

4

5

6

7 8 9

0

DISPLAY

YPbPr

SCREEN SIZE

SWAP

PIP ON

-

SLEEP

RECALL

MENU

ENTER

EXIT

SOURCE

MULTI-PIP

FREEZEPARENTALCC

PREPARATION (Continued)

Antenna Connection

ANTENNA

2. A 300-ohm system is a flat "twin-lead"cable that can be

attached to a 75-ohm terminal through a 300-75-ohm

adapter (not supplied)

1. A 75-ohm system is generally a round cable with F-type

Connector that can easily be attached to a terminal without

tools (not supplied).

OUTDOOR ANTENNA CONNECTION

Use one of the following two diagrams if you connect to an outdoor antenna

A: Using a VHF/UHF combination outdoor antenna

B: Using separate VHF and/or UHF outdoor antennas

Connect the outdoor antenna cable lead-in to ANT. (Antenna terminal) on the rear of the TV set.

F-type connector

75-ohm coaxical cable (round)

300-ohm twin lead cable (flat)

Separate VHF AND/OR

UHF Antennas

UHF antenna

300-ohm

twin-lead

VHF antenna

75-ohm

coaxical cable

300-ohm

twin-lead

Combiner

(not supplied)

OUT IN

9

The antenna requirements for good color television reception are more important than

those for black & white television reception. For this reason, a good quality outdoor

antenna is strongly recommended.

The following is a brief explanation of the type of connections that are provided with the

various antenna systems.

ENGLISH

PREPARATION (Continued)

Antenna Connection (Continued)

CABLE TV (CATV) CONNECTION

A 75-ohm coaxial cable connector is built into the back of the PDP TV for easy hookup. When

connecting the 75-ohm coaxial cable to the set, screw the 75-ohm cable to the ANT. Terminal.

Some cable TV companies offer "premium pay channels" Since some of these premium pay

channels are scrambled, a cable TV converter/descrambler is generally provided to the

subscriber by the cable TV company. This converter/descrambler is necessary for normal viewing

of the scrambled channels. (Set your TV to channel 3 or 4, typically one of these channels is used.

If this is unknown, consult your cable TV company.) For more specific instructions on installing

cable TV, consult your cable TV company. One possible method of utilizing the converter

/descrambler provided by your cable TV company is explained below:

"A"position on the RF switch (not supplied):You can view all unscrambled channels

by using the TVs channel keys.

"B"position on the RF switch (not supplied):the converter/descrambler by using the converters

channel keys.

Consult your Dealer or Service Center for the type of splitter, RF switch or combiner that might

be required.

1. Turn on power switch.

2. Plug AC cord(supplied)to product and wall outlet.

Power Connection

Use only a recommended AC plug code, if necessary, depending on the design of the wall

outlet.

Unplug the AC cord from the product and power outlet when not using the TV for a long period of

time.

Two-set

signal

splitter

(not

Supplied)

Cable TV converter/

descrambler (not supplied)

A

IN

B

OUT

Cable TV Line

Household power outlet

AC cord

10

Please note: An RF switch provided with two inputs (A and B) is required (not supplied).

NOTE

ENGLISH

REMOTE CONTROL OVERVIEW

Button Descriptions

11

Press to turn on and off the TV.

Press to select the applicable input source.

Press to select picture brightness .

Press to mute the sound. Press again to restore the sound.

Press repeatedly to cycle through the Multi-channel TV sound MTS options:

MONO, STEREO. and SAP.

Press repeatedly to scroll through the screen size options:4:3, ZOOM ,

Full screen.

Press to select the Closed Caption Function, see page 27 for further details.

Press to freeze the picture. Press again to restore the picture.

Press once to display the current channel number, available main and PIP

connections.

Press repeatedly to step through the 30MIN, 60MIN,90MIN, 120MIN, and OFF

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

POWER

SOURCE

BRIGHT

MUTE

MTS

SCREEN

SIZE

CC

FREEZE

DISPLAY

SLEEP

ENGLISH

8.

9.

10.

23.

12.

2.

16.

17.

18.

4.

3.

20.

25.

14.

5.

6.

7.

19.

21.

22.

24.

11.

13.

15.

1.

Press to select PARENTAL CONTROLS, see page 25.

Press to select HDTV picture if you connect a DVD player or digital set-top-box

to YPbPr jacks. Note that the DVD player or the digital set-top box needs to

have a built-in HDTV tuner, and you need to be tuned into an HDTV channel to

receive HDTV quality broadcasts.

Press to display the menu screen.

Press EXIT to exit from the menu screen.

Press to jump back and forth between two channels. The TV alternates

between the current channel and the last channel that was selected.

Press to enter and to set the function you choose in the menu screen.

Press to scan through channels. To scan quickly through channels, press and

hold down either CH .

Press to adjust the volume.

/

19.

20.

21.

22.

23.

24.

25.

PARENTAL

YPbPr

MENU

EXIT

RECALL

OK

CH /

VOL +/-

ZOOM +/-

0-9

PIP-ON

SWAP

MULTI-PIP

ENTER

12

11.

12.

13.

14.

15.

16.

17.

18.

Press ZOOM + to enlarge picture, press ZOOM - to shrink picture.

Press 0-9 to select a channel; the channel changes after 3 seconds.

Press repeatedly to cycle through the PIP size, PBP and POP picture.

See page 22 for further details.

Press to exchange main and sub picture in PIP, PBPand POP mode.

Press to let you operate Multi-PIP function, see page 23.

Press to move the cursor on screen. To select an item please press

the "OK" button.

Press to enter and to set the function you choose in the menu screen.

REMOTE CONTROL OVERVIEW(Continued)

Button Descriptions

ENGLISH

LCD TV CONTROLS OVERVIEW

13

REMOTE CONTROL RECEIVER

POWER ON/OFF

SOURCE

MENU

VOL+

VOL-

CH

NOTE

SOURCE, CH / , VOL +/-, and MENU button on the main unit have the same functions as

the same buttons on the remote control. Basically , this operation manual provides a description

based on operation with the remote control.

ENGLISH

14

CONNECTORS OVERVIEW

VHF/UHF Primary RF input connects to your VHF/UHF antenna or

cable.

S-VIDEO Connect to the S-VIDEO OUT jack of your VCR or other video equipment

that has S-VIDEO output jack S-VIDEO provides better picture quality th

ither composite video or VHF/UHF connections.

VIDEO Connect to the composite A/V output jacks on your VCR or other video

component.

YCbCr Video equipment connected to the YCbCr input terminals.

from 480 interlace output equipment is available.

YPbPr Connect to your DVD player's or digital set-top box's component video(Y,

Pb,Pr) and audio (L/R) jacks. Component video provide better picture quality

than r .

Connect to the left and ight udio input jacks of your audio amplifier. You can

LINE OUT R/ L use these outputs to listen to your TV's a dio through your stereo system.

through tuner that

an

e

component ( )

Use when signal

,o

AUDIO

1.

2.

3.

4.

5.

6.

1.

2.

3.

ENGLISH

YCbCr

YPbPr

VIDEO

AUDIO

AUDIO OUT

AUDIO

S-VIDEO

VHF/UHF

1.

4.

5.

2.

3.

6.

15

CONNECTORS OVERVIEW(Continued)

DVI INPUT JACK

PC(RGB INPUT JACK(15pin)

AUDIO LINE-IN

SERVICE PACK

1.

2.

3.

4.

Receives the digital video/audio signals from PC.

The DVI input is including HDCP.

Connect to the video/audio output jack on your PC.

PC "SOUND CARD"input 3.5mm jacket terminal.

For service only.

ENGLISH

1. 4.

2.

3.

BASIC OPERATION

16

SELECTING AN INPUT SOURCE

MAIN SOURCE

NOTE

VGA

DVI

S VIDEO

AV

YCbCr

TV

YPbPr

1. Turn on the power of the connected

Video equipment.

2. Press SOURCE and / to

select the main input source you

want to view.

The AV input mode indication

remains for 10 seconds.

3. VGA and DVI:

Connects to the VGA&DVI jack of

your Personal computer (PC). Note

that a DVI port is not a very common

jack on a PC as it requires a PC

which has a digital video card .

4. S VIDEO:

Connects to the S VIDEO out jack

of your VCR on other video

equipment that has S VIDEO.

5. AV:

Connects to the composite

AV output jacks on your VCR or

SOYO Atlas DYLT032C Owner's manual

This manual is also suitable for

SOYO Atlas DYLT032C Owner's manual

Other documents