Black & Decker KA330 User manual

Page is loading ...

4

ENGLISH

(Original instructions)

Intended use

Your BLACK+DECKER sander has been designed for sand-

ing wood, metal, plastics and painted surfaces. This tool is

intended for consumer use only.

Safety instructions

General power tool safety warnings

@

Warning! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions listed below may result in electric shock,

re and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in all of the warnings listed below refers

to your mains operated (corded) power tool or battery oper-

ated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b. Do not operate power tools in explosive atmospheres,

such as in the presence of ammable liquids, gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

c. Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodied plugs

and matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the inuence

of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in

serious personal injury.

b. Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

c. Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or

energising power tools that have the switch on invites

accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

5

ENGLISH

(Original instructions)

d. Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualied repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Additional power tool safety warnings

@

Warning! Additional safety warnings for sanders

u Hold power tool by insulated gripping surfaces when

performing an operation where the cutting accessory

may contact hidden wiring. Cutting accessory contacting

a "live" wire may make exposed metal parts of the power

tool "live" and could give the operator an electric shock

u Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding the

work by hand or against your body leaves it unstable and

may lead to loss of control.

@

Warning! Contact with or inhalation of dusts

arising from sanding applications may endanger

the health of the operator and possible bystand-

ers. Wear a dust mask specically designed for

protection against dust and fumes and ensure

that persons within or entering the work area are

also protected.

u Thoroughly remove all dust after sanding.

u Take special care when sanding paint which is possibly

lead based or when sanding some woods and metal which

may produce toxic dust:

t Do not let children or pregnant women enter the work

area.

t Do not eat, drink or smoke in the work area.

t Dispose of dust particles and any other debris safely.

u This tool is not intended for use by persons (including

children) with reduced physical, sensory or mental capa-

bilities, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use

of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not

play with the appliance.

u The intended use is described in this instruction manual.

The use of any accessory or attachment or performance

of any operation with this tool other than those recom-

mended in this instruction manual may present a risk of

personal injury and/or damage to property.

Safety of others

u This appliance is not intended for use by persons (includ-

ing children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concern-

ing use of the appliance by a person responsible for their

safety.

u Children should be supervised to ensure that they do not

play with the appliance.

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving

parts.

u Injuries caused when changing any parts, blades or

accessories.

u Injuries caused by prolonged use of a tool. When

using any tool for prolonged periods ensure you take

regular breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF.)

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured

in accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

6

ENGLISH

(Original instructions)

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following pictograms are shown on the tool:

:

Warning! To reduce the risk of injury, the user

must read the instruction manual.

Electrical safety

#

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

Using an extension cable

u Always use an approved extension cable suitable for the

power input of this tool (see technical data). Before use,

inspect the extension cable for signs of damage, wear and

ageing. Replace the extension cable if damaged or defec-

tive. When using a cable reel, always unwind the cable

completely. Use of an extension cable not suitable for the

power input of the tool or which is damaged or defective

may result in a risk of re and electric shock.

Features

This tool includes some or all of the following features.

1. On/off switch

2. Dust collection canister

3. Dust collection canister lock

4. Sanding base

5. Paper clamp lever

6. Variable speed control knob

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting sanding sheets (g. A & B - D)

Warning! Never use the tool without a sanding sheet or ac-

cessory in place.

Note: For best results always use punched sand paper. If your

sand paper is not punched then the dust collection canister

will not work.

Fitting sanding sheets with nylon loops (g. A)

u Make sure that the tool is switched off and unplugged.

u Press the sheet rmly and evenly onto the sanding base

(4), making sure that the holes in the sheet line up with the

holes in the base.

Fitting regular sanding sheets (g. B - D)

u Make sure that the tool is switched off and unplugged.

u Soften the sanding sheet by rubbing its non-abrasive side

over the edge of a worktop.

u Press the paper clamp levers (5) upwards to release them

from the retaining grooves and open the paper clamps by

pressing them down (g. B).

u Place the sheet onto the sanding base (4), making sure

that the holes in the sheet line up with the holes in the

base (g. C).

u Insert the edge of the sanding sheet into the front paper

clamp as shown (g. D).

u Press the front paper clamp lever (5) downwards and

locate it in the retaining groove.

u While keeping a slight tension on the sheet, insert the rear

edge of the sheet into the rear paper clamp.

u Press the rear paper clamp lever (5) downwards and

locate it in the retaining groove.

Fitting and removing the dust collection canister

(g. E & F)

u Turn the dust collection canister lock (3) anti-clockwise.

u Carefully slide out the dust collection canister (2).

u Lift the lter (7) out and empty the contents of the dust col-

lection canister. The lid of the lter can be gently tapped to

remove any particles that cling or is can be brushed with a

soft clean brush.

7

ENGLISH

(Original instructions)

u Insert the lter (7) into the dust collection canister (2).

u Slide the dust collection canister (2) into the tool.

u Lock the dust collection canister (3) into place by turning

the dust collection canister lock clockwise..

Note: Monitor the the dust collection canister (2) at regular in-

tervals. Empty the dust collection canister fequently to ensure

the best efciency of your tool.

Use

Warning! Let the tool work at its own pace. Do not overload.

Variable speed control

The variable speed control allows you to adapt the speed of

the tool to the workpiece material.

u Set the control knob (6) to the desired setting. Use a high

speed for wood, medium speed for veneer and synthetics

and low speed for acrylic glass, non-ferrous metals and for

removing paints.

Switching on and off (g. G)

u To switch the tool on, press the front part I of the on/off

switch (1).

u To switch the tool off, press the rear part O of the on/off

switch.

Hints for optimum use (g. H)

u Always hold the tool with both hands.

u Do not exert too much pressure on the tool.

u Regularly check the condition of the sanding sheet.

Replace when necessary.

u Always sand with the grain of the wood.

u When sanding new layers of paint before applying another

layer, use extra ne grit.

u On very uneven surfaces, or when removing layers of

paint, start with a coarse grit. On other surfaces, start with

a medium grit. In both cases, gradually change to a ne

grit for a smooth nish.

u Consult your retailer for more information on available

accessories.

Accessories

The performance of your tool depends on the accessory used.

BLACK+DECKER and Piranha accessories are engineered to

high quality standards and designed to enhance the perform-

ance of your tool. By using these accessories you will get the

very best from your tool.

Replacement packs of pre-punched sand paper are available

through you local BLACK+DECKER dealer.

For 80G - 5 sheet packs use part number X31517-XJ

For 120G - 5 sheet packs use part number X31522-XJ

For 240G - 5 sheet packs use part number X31527-XJ

Maintenance

Your tool has been designed to operate over a long period of

time with a minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and regular cleaning.

Warning! Before performing any maintenance, switch off and

unplug the tool.

u Regularly clean the ventilation slots in your tool using a

soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new

plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Protecting the environment

Z

Separate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your BLACK+DECKER product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product avail-

able for separate collection.

z

Separate collection of used products and packaging

allows materials to be recycled and used again.

Re-use of recycled materials helps prevent environ-

mental pollution and reduces the demand for raw

materials.

Local regulations may provide for separate collection of elec-

trical products from the household, at municipal waste sites or

by the retailer when you purchase a new product.

BLACK+DECKER provides a facility for the collection and re-

cycling of BLACK+DECKER products once they have reached

the end of their working life. To take advantage of this service

please return your product to any authorised repair agent who

will collect them on our behalf.

8

ENGLISH

(Original instructions)

You can check the location of your nearest authorised repair

agent by contacting your local BLACK+DECKER ofce at the

address indicated in this manual. Alternatively, a list of author-

ised BLACK+DECKER repair agents and full details of our

after-sales service and contacts are available on the Internet

at: www.2helpU.com

Technical data

KA330E

(Type 1)

Input voltage V

ac

230

Power input

W

270

Oscillations (no load) min

-1

10,000 - 26,000

Orbits (no load) min

-1

5,000 - 13,000

Sanding base surface

mm 90 x 187

Weight kg 1.8

L

pA

(sound pressure) 83.5 dB(A), Uncertainty (K) 3 dB(A)

L

WA

(sound power) 94.5 dB(A), Uncertainty (K) 3 dB(A)

Vibration total values (triax vector sum) according to EN 60745:

Vibration emission value (a

h

) 7.2 m/s

2

, uncertainty (K) 1.5 m/s

2

EC declaration of conformity

MACHINERY DIRECTIVE

%

KA330E

BLACK+DECKER declares that these products described

under "technical data" are in compliance with:

2006/42/EC, EN 60745-1, EN 60745-2-4

These products also comply with Directive 2014/30/EU

and 2011/65/EU. For more information, please contact

BLACK+DECKER at the following address or refer to the back

of the manual.

The undersigned is responsible for compilation of the technical

le and makes this declaration on behalf of BLACK+DECKER.

R.Laverick

Engineering Manager

BLACK+DECKER Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD, United Kingdom

05/08/2014

9

ENGLISH

(Original instructions)

Guarantee

BLACK+DECKER is condent of the quality of its products

and offers an outstanding guarantee. This guarantee state-

ment is in addition to and in no way prejudices your statutory

rights. The guarantee is valid within the territories of the

Member States of the European Union and the European Free

Trade Area.

If a BLACK+DECKER product becomes defective due to

faulty materials, workmanship or lack of conformity, within 24

months from the date of purchase, BLACK+DECKER guar-

antees to replace defective parts, repair products subjected

to fair wear and tear or replace such products to ensure

minimum inconvenience to the customer unless:

u The product has been used for trade, professional or hire

purposes;

u The product has been subjected to misuse or neglect;

u The product has sustained damage through foreign

objects, substances or accidents;

u Repairs have been attempted by persons other than au-

thorised repair agents or BLACK+DECKER service staff.

To claim on the guarantee, you will need to submit proof of

purchase to the seller or an authorised repair agent. You can

check the location of your nearest authorised repair agent by

contacting your local BLACK+DECKER ofce at the address

indicated in this manual. Alternatively, a list of authorised

BLACK+DECKER repair agents and full details of our after-

sales service and contacts are available on the Internet at:

www.2helpU.com

Please visit our website www.blackanddecker.co.uk to register

your new BLACK+DECKER product and to be kept up to date

on new products and special offers. Further information on the

BLACK+DECKER brand and our range of products is avail-

able at www.blackanddecker.co.uk

Page is loading ...

ENGLISH

Do not forget to register your product!

www.blackanddecker.co.uk/productregistration

Register your product online at www.blackanddecker.co.uk/pro-

ductregistration or send your name, surname and product code to

Black & Decker in your country

.

DEUTSCH

Vergessen Sie nicht, Ihr Produkt registrieren zu lassen!

www.blackanddecker.de/productregistration

Lassen Sie Ihr Produkt unter www.blackanddecker.de/productreg-

istration online registrieren oder schicken Sie Ihren Nachnamen,

Vornamen und den Produktcode an Black & Decker in Ihrem Land.

FRANÇAIS

N’oubliez pas d’enregistrer votre produit !

www.blackanddecker.fr/productregistration

Enregistrez votre produit en ligne sur www.blackanddecker.fr/

productregistration ou envoyez vos nom, prénom et code produit à

Black & Decker dans votre pays.

ITALIANO

Non dimenticate di registrare il prodotto!

www.blackanddecker.it/productregistration

Registrate il prodotto online su www.blackanddecker.it/productreg-

istration o inviate nome, cognome e codice del prodotto al centro

Black & Decker del vostro paese.

NEDERLANDS

Vergeet niet uw product te registreren!

www.blackanddecker.nl/productregistration

U kunt uw product online registreren op www.blackanddecker.nl/pro-

ductregistration of u kunt uw voornaam, achternaam en productcode

opsturen naar Black & Decker in uw land.

ESPAÑOL

¡No olvide registrar su producto!

www.blackanddecker.es/productregistration

Registre su producto on-line en www.blackanddecker.es/produc-

tregistration o envíe su nombre, apellidos y código de producto a

Black & Decker en su país.

PORTUGUÊS

Não se esqueça de registar o seu produto!

www.blackanddecker.pt/productregistration

Registe o seu produto online em www.blackanddecker.pt/productre-

gistration ou envie o seu nome, apelido e código do produto para a

Black & Decker no seu país.

SVENSKA

Glöm inte att registrera produkten!

www.blackanddecker.se/productregistration

Registrera produkten online på www.blackanddecker.se/productre-

gistration

eller skicka namn och produktkod till Black & Decker i landet

du bor i.

NORSK

Ikke glem å registrere produktet ditt!

www.blackanddecker.no/productregistration

Registrer produktet ditt online på www.blackanddecker.no/pro-

ductregistration, eller send ditt navn, etternavn og produktkode til

Black & Decker i ditt eget land.

DANSK

Glem ikke at registrere dit produkt!

www.blackanddecker.dk/productregistration

Registrer dit produkt på internettet på: www.blackanddecker.dk/

productregistration eller send dit navn, efternavn og produktkode til

Black & Decker i dit eget land.

SUOMI

Muistathan rekisteröidä tuotteesi!

www.blackanddecker./productregistration

Rekisteröi tuotteesi verkossa osoitteessa www.blackanddecker./

productregistration tai lähetä etunimesi, sukunimesi ja tuotekoodi

oman maasi Black & Decker -edustajalle.

Ε Λ Λ Η Ν Ι Κ Α

Μην ξεχάσετε να καταχωρίσετε το προϊόν σας!

www.blackanddecker.gr/productregistration

Καταχωρίστε το προϊόν σας σε σύνδεση στη σελίδα www.

blackanddecker.gr/productregistration ή στείλτε το όνομα, επίθετο

σας και τον κωδικό πριονωτός στη Black & Decker στη χώρα σας.

België/Belgique/Luxembourg Stanley Black & Decker Belgium BVBA Tel. NL +32 15 47 37 65

www.blackanddecker.be Egide Walschaertsstraat 16 Tel. FR +32 15 47 37 66

enduser[email protected] 2800 Mechelen Fax. +32 15 47 37 99

Danmark Black & Decker [email protected]

Roskildevej 22 www.blackanddecker.dk

2620 Albertslund

Deutschland Stanley Black & Decker Deutschland Gmbh Tel. 06126 21-0

www.blackanddecker.de Black & Decker Str. 40, D - 65510 Idstein Fax 06126 21-2980

[email protected]

Ελλάδα Stanley Black & Decker (ΕΛΛΑΣ) Ε.Π.Ε Τηλ. 210-8981616

www.blackanddecker.gr ΓΡΑΦΕΙΑ:Στράβωνος 7 & Βουλιαγμένης Φαξ 210-8983570

[email protected] 166 74 Γλυφάδα - Αθήνα

SERVICE: Ημερος Τόπος 2 -Χάνι Αδάμ Τηλ. Service 210-8985208

193 00 Ασπρόπυργος - Αθήνα Φαξ 210-5597598

España Stanley Black & Decker Ibérica, S.C.A. Tel. 934 797 400

www.blackanddecker.es Parc de Negocis “Mas Blau” Fax 934 797 419

[email protected] Edicio Muntadas, c/Bergadá, 1, Of. A6

08820 El Prat de Llobregat (Barcelona)

France Black & Decker (France) S.A.S. Tel. 04 72 20 39 20

www.blackanddecker.fr 5 allée des Hêtres Fax 04 72 20 39 00

B.P. 30084

69579 Limonest Cédex

Helvetia ROFO AG Tel. 026-6749393

www.blackanddecker.ch Gewerbezone Seeblick Fax 026-6749394

[email protected] 3213 Kleinbösingen

Italia Stanley Black & Decker Italia Tel. 039-9590200

www.blackanddecker.it Via Energypark 6 Fax 039-9590313

[email protected] 20871 Vimercante (MB) Numero verde 800-213935

Nederland Stanley Black & Decker Netherlands BV Tel. +31 164 283 065

www.blackanddecker.nl Holtum Noordweg 35, 6121 RE BORN Fax +31 164 283 200

enduser[email protected] Postbus 83, 6120 AB BORN

Norge Black & Decker [email protected]

Postboks 4613, Nydalen www.blackanddecker.no

0405 Oslo

Österreich Stanley Black & Decker Austria GmbH Tel. 01 66116-0

www.blackanddecker.at Oberlaaerstraße 248, A-1230 Wien Fax 01 66116-614

[email protected]

Portugal Black & Decker Limited SARL Tel. 214667500

www.blackanddecker.pt Quinta da Fonte - Edifício Q55 D. Diniz Fax 214667580

[email protected] Rua dos Malhões, 2 e 2A - Piso 2 Esquerdo

2770 - 071 Paço de Arcos

Suomi Black & Decker asiakaspalvelu.@sbdinc.com

PL47 www.blackanddecker.

00521, Helsinki

Sverige Black & Decker AB [email protected]

Box 94, 431 22 Mölndal www.blackanddecker.se

Türkiye KALE Hırdavat ve Makina A.Ş. Tel. 0212 533 52 55

www.blackanddecker.com.tr Defterdar Mah. Savaklar Cad. No:15 Fax. 0212 533 10 05

Edirnekapı / Eyüp / İstanbul 34050

United Kingdom & Black & Decker Tel. 01753 511234

Republic Of Ireland 210 Bath Road Fax 01753 512365

www.blackanddecker.co.uk Slough, Berkshire SL1 3YD

[email protected]

Middle East & Africa Black & Decker Tel. +971 4 8863030

www.blackanddecker.ae P.O.Box - 17164 Fax +971 4 8863333

[email protected] Jebel Ali Free Zone (South), Dubai,

UAE

90615059 REV-0

08/2014

Black & Decker KA330 User manual

Black & Decker KA330 User manual

in other languages

Related papers

Other documents