Facom S.248-340D Owner's manual

Type
Owner's manual

This manual is also suitable for

Facom S.248-340D is a torque wrench with a range of 60 to 340 Nm. It features a 1/2" square drive and comes with a 3/8" to 1/2" adapter. This wrench is ideal for tightening bolts and nuts to a specific torque, ensuring that they are neither under nor over-tightened.

To use the S.248-340D, first set the desired torque by turning the handle and aligning the vernier with the graduation. Then, place the wrench perpendicular to the tightening axis and pull progressively until you hear a click. This indicates that the desired torque has been reached.

The S.

Facom S.248-340D is a torque wrench with a range of 60 to 340 Nm. It features a 1/2" square drive and comes with a 3/8" to 1/2" adapter. This wrench is ideal for tightening bolts and nuts to a specific torque, ensuring that they are neither under nor over-tightened.

To use the S.248-340D, first set the desired torque by turning the handle and aligning the vernier with the graduation. Then, place the wrench perpendicular to the tightening axis and pull progressively until you hear a click. This indicates that the desired torque has been reached.

The S.

Notice d'instructions
Instruction manual
Bedienungsanleitung
Gebruiksaanwijzing
Guia de instrucciones
Istruzioni per l'utilizzo
Instrukcja obsugi
NU-JS.208-248/0702
J.S.208
J.S.248
®
®
BELGIQUE/LUXEMBOURG
FACOM Belgique S.A/NV
Weihoek 4 1930 Zaventem
BELGIQUE
: (02) 714 09 00
Fax : (02) 721 24 11
DANMARK/FINLAND
ISLAND/NORGE
SVERIGE
FACOM NORDEN A/S
Navervej 16B
7451 Sunds
DANMARK
: (45) 971 444 55
Fax : (45) 971 444 66
DEUTSCHLAND
FACOM GmbH
Postfach 13 22 06
42049 Wuppertal
Otto-Wels-Straße 9
42111 Wuppertal
DEUTSCHLAND
: (0202) 270 63 0
Fax : (0202) 270 63 50
ESPAÑA/PORTUGAL
FACOM Herramientas SRL
Polig. industrial de Vallecas
C.Luis 1°, s/n-Nave 95 - 2°Pl.
28031 Madrid
ESPAÑA
: (91) 778 21 13
Fax : (91) 778 27 53
ITALIA
USAG Gruppo FACOM
Via Volta 3,
21020
Monvalle (VA)
ITALIA
: (0332) 790 111
Fax : (0331) 790 602
POLSKA
FACOM Oddzial w Warszawie
ul. Marconich 9 m.3
02-954 Warszawa
POLSKA
: (0048 22) 642 71 14
Fax : (0048 22) 651 74 69
NEDERLAND
FACOM Gereedschappen BV
Kamerlingh Onnesweg 2
Postbus 134
4130 EC Vianen
NEDERLAND
: (0347) 362362
Fax : (0347) 376020
SINGAPORE/FAR EAST
FACOM Tools FAR EAST Pte.Ltd
15 Scotts Road
Thong Teck Building # 08.01.02
Singapore 228218
SINGAPORE
: (65) 732 0552
Fax : (65) 732 5609
SUISSE/ÖSTERREICH
MAGYARORSZAG
CESKA REP.
FACOM S.A./AG
12 route Henri-Stéphan
1762 Givisiez/Fribourg
SUISSE
: (4126) 466 42 42
Fax : (4126) 466 38 54
UNITED KINGDOM/EIRE
FACOM -UK
Churchbridge Works-Walsall Road
CANNOCK STAFFORDHIRE WS11 3JR
UNITED KINGDOM
: (01922) 702 150
Fax : (01922) 702 152
UNITED STATES
FACOM TOOLS Inc.
3535 West 47th Street
Chicago Illinois 60632
U.S.A.
: (773) 523 1307
Fax : (773) 523 2103
FRANCE ET
INTERNATIONAL
Société FACOM
6-8, rue Gustave Eiffel B.P.99
91423 Morangis cedex
FRANCE
: 01 64 54 45 45
Fax : 01 69 09 60 93
http://www.facom.fr
Nm
mini maxi N.m mm L1 L2 g
J.208-50 10 50 1 3/8" --------------- 360 281 900
S.208-100 20 100 1 1/2" --------------- 420 340 1040
S.208-200 40 200 1 1/2" --------------- 480 400 1220
S.208-340 60 340 2 1/2" --------------- 635 553 1540
J.208-50D 10 50 1 --------------- 9 x 12 340 299 780
S.208-100D 20 100 1 --------------- 9 x 12 400 358 920
S.208-200D 40 200 1 --------------- 14 x 18 465 434 1110
S.208-340D 60 340 2 --------------- 14 x 18 620 587 1430
J.248-50D 10 50 --------------- --------------- 9 x 12 330 286 740
S.248-100D 20 100 --------------- --------------- 9 x 12 400 355 880
S.248-200D 40 200 --------------- --------------- 14 x 18 465 431 1080
S.248-340D 60 340 --------------- --------------- 14 x 18 620 584 1400
Accessoires - Accessories - Zubehör - Toebehoren - Accesorios - Accessori - Akcesoria
Caractéristiques - Specifications - Kenndaten - Specificaties - Características - Caratteristiche - Parametry techniczne
ISO 6789
Précision des clés / Torque wrench precision / Schlüssel-Genauigkeit
Nauwkeurigheid van de sleutels / Precisión de las llaves / Precisione delle chiavi / Dokadność
±4%
J.208-50D 10 12
J.248-50D 7 19mm 7 19mm
S.208-100D 1/4 3/4" 1/4 3/4"
S.248-100D S.305P
S.208-200D
S.248-200D 11 13
S.208-340D 13 32 13 36mm
S.248-340D 1/21"1/4 1/21"7/16
J.372 3/8" J.373
S.372 1/2" S.373
S.382 1/2" S.383
}
For series 208 Setting the required torque For series 248
1 Pull the ring towards the handle
2 Turn the handle and set the vernier to
the desired graduation
3 Release the ring, which will then click
into position.
Hints
Use the torque table at the end of these instructions The standard unit of measurement is the Newton-metre, symbol Nm
1 metre-kilo = 9.81 Nm
(about 10 Nm)
1 ft/lb = 1.35 Nm 1 in/lb = 0,1128 Nm 1 in/oz = 0.00705 Nm
1 Nm = 0.102 metre-kilo
(about 100 g/m)
1Nm = 0,738 ft/lb 1 Nm = 8.863 in/lb 1 Nm = 141.8 in/oz
Never exceed the maximum torque of your wrench, taking special care when freeing tight nuts and during angular tightening.
Set the torque wrench to the minimum torque before putting it away in its box.
Maintenance
Clean your torque wrench with a dry cloth. Do not use any solvent or detergent.
Never dismantle.
Maintenance of precision
We advise you to have your torque wrench checked regularly on a test rig or by the FACOM metrological laboratory
(about once a year, or more often for intensive
use or if dropped)
.
Precision checking and updating of reports:
The FACOM metrological laboratory will draw up test reports or calibration certificates on request :
For series 208 . Test report : Testing and adjustment, if necessary, at
20, 60 and 100% of the torque wrench’s capacity, within the tolerances
specified in the standard.
A dated and numbered report is drawn up.
Calibration certificate : Testing and adjustment of the torque wrench at
6 or 12 values, testing apparatus linked to the national measuring stan-
dard. A dated and numbered official document is drawn up.
For further information ; ask your dealer.
For series 248. Test report : Repetitive testing
(and adjustment if necessary)
at 20, 60 and 100% of the torque wrench’s capacity, within the tolerances
specified in the standard.
A dated and numbered report is drawn up.
Pre-setting : Setting to required torque and testing repeatability.
A dated and numbered report is drawn up.
GB
Tightening
A Hold the torque wrench at right angles to the
tightening axis
B Place your hand in the middle of the handle
C Pull progressively and at right angles to the torque
wrench
D When the wrench "clicks" stop pulling immediately.
1 Unscrew plug b and insert an allen key at the
back of the wrench.
2 Adjust to the required torque with a testing
device. Tighen to increase the torque, untighten
to decrease.
3 Remove the allen hey and screw plug b back on.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Facom S.248-340D Owner's manual

Type
Owner's manual
This manual is also suitable for

Facom S.248-340D is a torque wrench with a range of 60 to 340 Nm. It features a 1/2" square drive and comes with a 3/8" to 1/2" adapter. This wrench is ideal for tightening bolts and nuts to a specific torque, ensuring that they are neither under nor over-tightened.

To use the S.248-340D, first set the desired torque by turning the handle and aligning the vernier with the graduation. Then, place the wrench perpendicular to the tightening axis and pull progressively until you hear a click. This indicates that the desired torque has been reached.

The S.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI