Black & Decker KR580 User manual
- Category
- Power tools
- Type
- User manual
KR580
KR650
KR700
KR580-700 UK p01-12 02-02-2001, 14:411
Congratulations!
On the purchase of your
Black & Decker corded drill.
To ensure the best results from your corded
drill please read these safety and usage
instructions carefully.
If you have any questions or queries after
reading this user manual please do not
hesitate to call our Service and Information
Centre, whose number you will find towards
the back of this user manual, or one of our
Authorised Repair Agents. A list of these
Agents and further information is available on
the Internet at www.2helpU.com.
KR580-700 UK p01-12 02-02-2001, 14:412
Contents
Page 4
Safety instructions
Double insulation
Page 5
Electrical safety
Mains plug replacement
Extension cables
Unwanted tools and the environment
The Black & Decker guarantee
Page 6
After sales service for your Black & Decker product
Our after sales service policy
Accessories
Technical data
Features
Page 7
Fitting the drill bit
Removing the chuck
Fitting the side handle
Setting the adjustable depth stop
Page 8
Preparing your drill for operation
Using your drill
Handy hints
Cooling down
Overload
EC declaration of conformity
Black & Decker phone numbers and addresses
Guarantee card
KR580-700 UK p01-12 02-02-2001, 14:413
4
SAFETY INSTRUCTIONS
Warning! When using electric tools, the following
basic safety precautions should always be taken to
reduce the risk of fire, electric shock and personal
injury. Read all these instructions before attempting to
operate the product and save this booklet.
For safe operation:
• Keep the work area clean. Cluttered areas and
benches invite injuries.
• Consider the work area environment. Do not expose
the power tool to rain and do not use in damp or wet
locations. Keep the work area well lit. Do not use
the power tool where there is a risk to cause fire
or explosion.
• Guard against electric shock. Avoid body contact,
where possible, with earthed or grounded surfaces
(e.g. pipes, radiators, ranges and refrigerators).
• Keep children away. Do not let visitors touch the
tool or extension cord. All visitors should be kept
away from the work area.
• Store idle tools. When not in use, tools should be
stored in a dry, high or locked place, out of reach
of children.
• Do not force the tool. It will do the job better and
more safely at the rate for which it was intended.
• Use the right tool. Do not force small tools or
attachments to do the job of a heavy duty tool.
Do not use the tool for purposes not intended; for
example, do not use a circular saw to cut tree
limbs or logs.
• Dress properly. Do not wear loose clothing or
jewellery as they can be caught in moving parts.
Rubber gloves and non-skid footwear are
recommended when working outdoors. Wear
protective hair covering to contain long hair.
• Use safety glasses. Use a face or dust mask as well,
if the operation is dusty or if the tool is being used in
enclosed spaces.
• Connecting dust extraction equipment. If devices
are provided for the connection of dust extraction
and collection ensure these are connected and
properly used, especially in confined areas.
• Do not abuse the cord. Never carry the tool by its
cord or yank it to disconnect it from the socket. Keep
the cord away from heat, oil and sharp edges.
• Secure the work. Use clamps or a vice to hold the
work. It is safer than using a hand and it frees both
hands to operate the tool.
• Do not overreach. Keep proper footing and balance at
all times.
• Maintain the tool with care. Keep a cutting tool
sharp and clean for better and safer performance.
Follow the instructions for lubricating and changing
accessories. Inspect the tools cord periodically and,
if damaged, have repaired by an authorised service
facility. Inspect the extension cord periodically and
replace if damaged. Keep the handles dry, clean and
free from oil and grease.
• Disconnect the tool when not in use, before
servicing and when changing accessories such as
blades, bits and cutters.
• Remove adjusting keys and wrenches. Form the
habit of checking to see that keys and adjusting
wrenches are removed from the tool and replaced in
the storage area before switching on.
• Avoid unintentional starting. Do not carry a
plugged-in tool with a finger on the switch.
Ensure the switch is off when plugging in.
• Use an outdoor extension cord. When a tool is used
outdoors, only use an extension cord intended for
outdoor use and so marked.
• Stay alert. Watch what you are doing, use common
sense and do not operate the tool when tired.
• Check damaged parts. Before further use of the tool,
a guard or other part that is damaged should be
carefully checked to determine whether it will
operate properly and perform its intended function.
Check for alignment of moving parts, free running of
moving parts, breakage of parts, mounting and any
other conditions that may affect its operation. A
guard or other part that is damaged should be
properly repaired or replaced by an authorised
service centre unless otherwise indicated in the
product booklet. Have defective switches replaced
by an authorised service centre. Do not use the tool
if the switch does not turn it on and off.
• Warning! The use of any accessory or attachment,
other than recommended in the product booklet,
may present a risk of personal injury.
• Have the tool repaired by a qualified person. The
electrical tool is in accordance with the relevant
safety requirements. Repairs should only be carried
out by qualified persons using original spare parts,
otherwise, this may result in considerable danger to
the user.
Save these instructions!
DOUBLE INSULATION
The tool is double insulated. This means that all
the external metal parts are electrically insulated
Corded drills user manual
KR580-700 UK p01-12 02-02-2001, 14:414
5
ENGLISH
from the mains power supply. This is done by
placing insulation barriers between the
electrical and mechanical components making
it unnecessary for the tool to be earthed.
Note: Double insulation does not take the place
of normal safety precautions when operating the
tool. The insulation system is for added protection
against injury resulting from a possible electrical
insulation failure within the tool.
ELECTRICAL SAFETY
Be sure the supply is the same as the voltage given on
the rating plate. The tool is fitted with a two-core cable
and plug.
MAINS PLUG REPLACEMENT (UK ONLY)
Should the mains plug need replacing and you are
competent to do this, proceed as instructed below.
If you are in doubt, contact a Black & Decker service
centre or a qualified electrician.
• Disconnect the plug from the power supply.
• Cut off the plug and dispose of safely. A plug with
bared copper conductors is very dangerous if
engaged in a live socket outlet.
• Only fit BS1363A approved plugs fitted with the
correctly rated fuse.
Note: Fuses do not give personal protection against
electric shock.
• The cable wire colours, or a letter, will be marked at
the connection point of most good quality plugs.
Attach the wires to their respective points in the plug
(see diagram). Brown is L (live) and blue is N (neutral).
Fit a 5 amp fuse
approved
to BS1362
N
L
E
230 volts AC only
Never use a light
socket
Make sure that the
outer sheath of the
cable is held firmly
by the clamp
Fit a BS1363A
approved
resilient plug
Connect
blue to
N (neutral)
Connect
brown to
L (live)
• Before replacing the top cover of the plug ensure
that the cable restraint is holding the outer sheath of
the cable firmly and that the two leads are correctly
fixed at the terminal screws. If the fuse cover is
missing or damaged do not use the plug. For
replacement or detachable fuse covers, contact a
Black & Decker service centre.
Warning! Never connect live or neutral wires to the
earth pin marked E or .
MAINS PLUG REPLACEMENT
(AUSTRALIA AND NEW ZEALAND ONLY)
Should the mains plug or cordset of the product be
damaged, it must only be replaced by an authorised
Black & Decker service agent because special
purpose tools are required.
EXTENSION CABLES
Up to 30m (100ft) of Black & Decker 2-core extension
cable (or 3-core extension cordset, in Australia and
New Zealand) can be used without undue loss of power.
Note: An extension cable should not be used unless
absolutely necessary. Use of an improper extension
cable could result in a risk of fire and electric shock.
If an extension cable must be used, make sure it is
properly wired, contains the correct rated fuse as
recommended in its literature and is in good
electrical condition.
UNWANTED TOOLS AND THE ENVIRONMENT
Should you find one day that the tool needs
replacement or is of no further use, think of the
protection of the environment. Black & Decker
service centres will accept old tools and will
dispose of them in an environmentally safe way.
THE BLACK & DECKER GUARANTEE
(UK, AUSTRALIA AND NEW ZEALAND ONLY)
If the Black & Decker product becomes defective due
to faulty materials and workmanship, within 24 months
from the date of purchase, we guarantee to either
replace all defective parts or at our discretion, replace
the unit free of charge provided that:
• The product is returned to us or our authorised
repairers with evidence of date of purchase.
• The product has not been used for trade,
professional or hire purposes.
• The product has not been subjected to misuse
or neglect.
• The product has not sustained any damage through
foreign objects, substances or accidents.
• Repairs have not been attempted by anyone other
than our own service staff or authorised repair
distributors.
KR580-700 UK p01-12 02-02-2001, 14:415
6
ENGLISH
This guarantee is offered as an extra benefit and is
additional to the customers statutory rights.
AFTER SALES SERVICE FOR THE BLACK & DECKER
PRODUCT (UK, AUSTRALIA AND NEW ZEALAND ONLY)
Black & Decker offers a nationwide network of
authorised service agents. The use of other than
genuine Black & Decker accessories and parts
may damage or reduce the performance of your
Black & Decker product and may also endanger the
user. The terms and conditions of the warranty may
also be effected.
OUR AFTER SALES SERVICE POLICY
(UK, AUSTRALIA AND NEW ZEALAND ONLY)
It is our aim that all Black & Decker customers should
be totally satisfied with their Black & Decker product
and after sales service, but if help or advice is needed
please contact your local Black & Decker authorised
repair agent who will be happy to help. Full details of
our after sales service and a list of these agents can be
found on the Internet at www.2helpU.com. Alternatively,
call our Service and Information Centre whose number
you will find towards the back of this manual.
ACCESSORIES
The performance of any power tool is dependant upon
the accessory used. Black & Decker accessories are
engineered to high quality standards and are designed
to enhance the performance of your tool. Buying a
Black & Decker accessory will ensure that you get the
very best from your Black & Decker tool.
TECHNICAL DATA
The level of sound pressure of the tool is in
accordance with EEC legislation. It is recommended
that you take appropriate measures for the protection
of your hearing if the sound level seems
uncomfortable. This normally equates to a sound
pressure in excess of 85dB (A).
KR580 KR650 KR700
Voltage 230V 230/240V 230/240V
Power 580W 650W 700W
No load speed 0-3000min
-1
0-3000min
-1
0-3000min
-1
Drilling capacities:
Steel 13mm 13mm 13mm
Concrete 13mm 13mm 16mm
Wood 25mm 25mm 32mm
Note: This user manual also covers more than one
catalogue number within this product group. Refer to
your carton for details of your product.
FEATURES
1. Variable speed control
2. On/off switch
3. Lock-on button
4. Side handle
5. Adjustable depth stop
6. Chuck jaws
7. Chuck
8. Hammer/drill switch
9. Forward/reverse switch
10. Spindle lock
Your drill includes some or all of these features:
• The on/off switch is used to operate your drill in all
modes of operation.
• The variable speed control provides optimal control
of your drill for a wide range of tasks.
• The lock-on button provides continuous operation
of your drill.
• The side handle gives a secondary gripping position
for your drill.
• Your drill can operate as a hammer drill or as a
rotary drill depending on the setting of the hammer/
drill switch.
8
6
7
4
9
5
3
2
1
•
•
•
•
•
8
10
6
7
4
9
5
3
2
1
•
•
•
•
•
•
•
•
•
•
•
•
KR580-700 UK p01-12 02-02-2001, 14:416
7
• The forward/reverse switch controls the direction of
rotation when your drill is used as a screwdriver, or
when clearing a jammed drill bit.
• The adjustable depth stop gives precise control of
the hole depth, when you drill blind holes.
FITTING THE DRILL BIT (KEYLESS CHUCKS)
Proceed as follows:
Disconnect the plug from the electricity supply.
While pressing
the spindle lock,
rotate the chuck
until the jaws are
sufficiently open.
Insert the drill bit
in the jaws of the
chuck and
tighten. Twist the
chuck firmly to securely grip the drill bit.
FITTING THE DRILL BIT (KEYED CHUCKS)
Proceed as follows:
Disconnect the plug from the electricity supply.
Rotate the barrel
of the chuck until
the jaws are
sufficiently open.
Insert the drill bit
in the jaws of the
chuck. Insert the
chuck key with
the end of the
chuck key in one of the three holes in the body of the
chuck, ensuring the head of the chuck key is engaged
with the barrel of the chuck. Turn the chuck key
clockwise to tighten the jaws and securely grip the drill
bit. Remove the chuck key.
REMOVING THE CHUCK (KEYLESS CHUCKS)
Proceed as follows:
To remove the chuck, open the jaws, hold it firmly in
one hand and with a screwdriver held in the other hand,
turn the set-screw in the chuck clockwise
approximately one turn, to loosen it.
Place an allen
key in the chuck
and tighten the
jaws. Give the
allen key a short
powerful blow in
an anti-clockwise
direction with a
hammer to loosen the chuck on the spindle. Remove
the allen key. Use the screwdriver to turn the set-screw
clockwise until it totally disengages from the spindle.
Remove the chuck from the spindle by rotating it anti-
clockwise. To fasten the chuck, put it on the thread and
turn it clockwise until it stops. Put in the screw and turn
it anti-clockwise until absolutely firm.
REMOVING THE CHUCK (KEYED CHUCKS)
To remove the
chuck, open the
jaws of the chuck
with the chuck
key. Hold the
chuck firmly in one
hand, and with a
screwdriver turn
the set screw in
the chuck clockwise with the other hand until it comes
out. Use only the correct chuck key. Place the chuck
key into the chuck, and hold the drill firmly in one hand
with the chuck pointing away from you. Rotate the
chuck so that the chuck key is just above the horizontal
position on the right hand side of the machine. Give the
crossbar end of the key a sharp downward blow with a
mallet or light hammer. The chuck should now be
sufficiently loose to be unscrewed by hand.
FITTING THE SIDE HANDLE
Loosely locate the
handle on the
body of your drill.
Rotate the handle
around the body
of your drill until it
is in the desired
position. Tighten
the handle by
turning clockwise.
SETTING THE ADJUSTABLE DEPTH STOP
Proceed as follows:
Fit the drill bit. Loosen the side handle.
Slide the depth
stop until the end
of the depth stop
aligns with the
end of the drill bit.
Slide the depth
stop until the
distance between
the end of the
ENGLISH
KR580-700 UK p01-12 02-02-2001, 14:417
8
ENGLISH
depth stop and the end of the drill bit is equal to the
length of the screw you will fit. Tighten the side handle.
PREPARING YOUR DRILL FOR OPERATION
Proceed as follows:
Fit the correct accessory for the job.
Set the speed of
your drill by
setting the
variable speed
control to the
desired position.
As a general rule,
for large size drill bits use low speeds and for smaller
drill bits use high speeds.
Set the forward/
reverse switch to
the desired
direction of
rotation. Never
change the setting
of the hammer/
drill switch, the variable speed control or the forward/
reverse switch when your drill is in operation.
USING YOUR DRILL
To switch your
drill on, depress
the on/off switch.
Your drill stops
when the switch
is released.
If continuous
operation is
required, depress
the lock-on button
while the on/off
switch is
depressed. To stop
your drill when
operation is
continuous, depress the switch again and release.
While your drill is in operation, do not touch the chuck.
HANDY HINTS
• Fit the correct size and type of drill or screwdriver bit.
• Always hold your drill using the handle and the
side handle.
• Always hold your drill at right-angles to your work.
When drilling
wood and metal,
set the hammer/
drill switch to the
drill mode .
When drilling
masonry, set the
hammer/drill
switch to the
hammer mode . When screwdriving, set the
hammer/drill switch to the drill mode .
• Set the forward/reverse switch to the correct direction.
• Never change the direction of rotation when your
drill is in operation.
• After use, remove the drill bit and gently tap the side
of the chuck with a soft-faced hammer to remove
the dust. This will extend the life of the chuck.
COOLING DOWN
If your drill becomes too hot in use, set the variable
speed control to its highest setting and allow your drill
to operate without load for 2 minutes.
OVERLOAD
Never use excessive force when using your drill. Too
much pressure can reduce the speed of your drill and
reduce its efficiency. This can result in an overload
which can cause damage to the motor of your drill.
EC DECLARATION OF CONFORMITY
We declare that units: KR580RE, KR580CRE, KR650RE,
KR650CRE, KR700RE, KR700CRE conform to 98/37/EC,
89/336/EEC, EN55014, 73/23/EEC, EN55104, EN50144
A weighted sound pressure 99dB (A)
A weighted sound power 112dB (A)
Hand/arm weighted vibration 8.89m/s
2
Brian Cooke - Director of Engineering
Black & Decker Ltd, Spennymoor, County Durham
DL16 6JG United Kingdom
The Black & Decker policy is one of continuous
improvement to our product and as such we reserve
the right to change the product specification without
prior notice.
KR580-700 UK p01-12 02-02-2001, 14:418
9
TYP.
1-2
KR650RE KR700RE
KR580CRE KR650CRE KR700CRE
E12544 / 374254-00
www.2helpu.com
29 - 08 - 2000
101
102
103
104
106
107
108
109
110
111
112
113
114
127
129
122
123
130
130
116
117
135
103
120
131
137
138
141
140
139
142
124
125
CRE
CRE
RE
143
121
KR700
136
118
132
134
133
105
119
TYPE 2
133
TYPE 1
105
134
119
KR580-700 UK p01-12 02-02-2001, 14:419
Part no: 374225-04 2/01.2
Australia DeWalt Power Tool Company Pty Ltd Tel: 03 9895 9200
7 Clarice Road, Box Hill Fax: 03 9899 7465
Victoria 3128
New Zealand Black & Decker Tel: 09 579 7600
483 Great South Road Fax: 09 579 8200
Penrose, Auckland
South Africa Black & Decker South Africa (Pty) Ltd Tel: 011 314 4431
Suite no 107, PostNet X65 Fax: 011 314 4435
Halfway House 1685
United Kingdom Black & Decker Tel: 01753 574277
210 Bath Road, Slough Tlx: 848317 BAND MH
Berkshire SL1 3YD Fax: 01753 551155
KR580-700 UK p01-12 02-02-2001, 14:4110
Address of the dealer where your corded drill was purchased: Date of your purchase:
Was your corded drill a gift?
Was your corded drill your first purchase?
Was your corded drill bought as a replacement?
What was the price of your corded drill?
Address of the dealer where your corded drill was purchased:
Name:
House number or name and street:
Town:
County or state:
Postcode:
Country:
Product catalogue number:
KR___/___
Data protection act: Tick this box if you prefer not to receive
information from Black & Decker or other companies.
Yes No
KR580-700 UK p01-12 02-02-2001, 14:4111
Part no: 374225-04 2/01.2
GUARANTEE CARD FOR THE UK, IRELAND AND SOUTH AFRICA
South Africa: Black & Decker South Africa (Pty) Ltd, Suite no 107, PostNet X65, Halfway House 1685
United Kingdom & Ireland: PO Box 821, Slough, Berkshire, SL1 3AR
Please complete this section immediately after the purchase of your corded drill
and post it to the Black & Decker address in your country (above).
If you live in Australia or New Zealand, please register your purchase by using the
alternative guarantee card supplied.
KR580-700 UK p01-12 02-02-2001, 14:4112
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Black & Decker KR580 User manual
- Category
- Power tools
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Black and Decker KR700 Owner's manual
-
BLACK+DECKER KR60 User manual
-
BLACK+DECKER KC9045 User manual
-
-
BLACK DECKER KW800 User manual
-
Black & Decker KC1482F User manual
-
-
BLACK+DECKER KR705 User manual
-
-
Black & Decker KR702 User manual