Razor Dirt Rocket MX350 Owner's manual

Brand: Razor

Model: Dirt Rocket MX350

Category: Scooters

Type: Owner's manual

This manual is also suitable for

dirt rocket MX400

Razor Dirt Rocket MX350: Unleash the Thrill of Electric Motorbike Adventure!

Experience exhilarating rides with the Razor Dirt Rocket MX350, an electric motorbike designed for thrilling adventures. Tackle various terrains with ease, from smooth pavements to flat, dry grounds, and enjoy a top speed of approximately 14 mph (22 kmh). Its powerful motor and sturdy construction provide a smooth and controlled ride, while the hand-operated brakes ensure quick and responsive stops.

Razor Dirt Rocket MX350: Unleash the Thrill of Electric Motorbike Adventure!

NOTE: Manual illustrations are for demonstration purposes only.

Illustrations may not reﬂ ect exact appearance of actual product.

Speciﬁ cations subject to change without notice.

Please have your product along with the 19 character product I.D. code with you

before contacting Razor for warranty assistance and/or replacement parts.

Product I.D. Code: _____________ - ____________ - ____________

Read and understand this entire manual before allowing

child to use this product! For assistance contact Razor.

DO NOT RETURN TO STORE.

OWNER’S MANUAL

SAFETY WARNINGS

CONTENTS

WARNING: Riding an electric motorbike does present potential

risks and caution is required. Like any riding product, the Dirt Rocket has

inherent hazards associated with its use (for example, falling off or riding it

into a hazardous situation). Like any riding product, the Dirt Rocket can and

is intended to move and it is therefore, of course, possible to lose control or

otherwise get into dangerous situations. Both children, and adults responsible

for supervising them, must recognize that if such things occur, a rider can

be seriously injured or die even when using safety equipment and other

precautions. RIDE AT YOUR OWN RISK AND USE COMMON SENSE.

WARNING: PARENTAL AND ADULT

RESPONSIBILITY AND SUPERVISION IS NECESSARY:

Because products, like the Dirt Rocket, can and do present potential hazards

plainly associated with their use, it is well recognized THE NEED FOR

EXERCISE OF PARENTAL RESPONSIBILITY IN SELECTING RIDING PRODUCTS

APPROPRIATE TO THE AGE OF A CHILD, OR PARENTAL SUPERVISION IN

SITUATIONS IN WHICH CHILDREN OF VARIOUS AGES MAY HAVE ACCESS

TO THE SAME RIDING PRODUCTS, IS IMPORTANT. Not every product is

appropriate for every age or size of child, and different age recommendations

are found within this category of product which are intended to reﬂect the

nature of the hazards and the expected mental or physical ability, or both, of a

child to cope with the hazards.

The recommended minimum rider age is 13 and older. Any rider unable

to ﬁt comfortably on the Dirt Rocket should not attempt to ride it. A parent’s

decision to allow his or her child to ride this product should be based on the

child’s maturity, skill and ability to follow rules.

Keep this product away from small children and remember that it is

intended for use only by persons who are, at a minimum, completely

comfortable and competent while operating the product.

Persons with any mental or physical conditions that may make them

susceptible to injury, impair their physical dexterity or mental capabilities

to recognize, understand, and follow safety instructions and to be able

to understand the hazards inherent in product use, should not use or be

permitted to use products inappropriate for their abilities. Persons with

heart conditions, head, back or neck ailments (or prior surgeries to these

areas of the body), or pregnant women, should be cautioned not to operate

such products.

DO NOT EXCEED THE WEIGHT LIMIT OF 140 lb (64 kg). Rider weight

does not necessarily mean a person’s size is appropriate to ﬁt or

maintain control of the product.

CHECK AND MAINTAIN PRODUCT CONDITIONS

Before use, check to conﬁrm that any and all chain guards or other

covers and guards are in place and in serviceable condition. Check that

the brake is functioning properly, and that tires are inﬂated properly and

have sufﬁcient tread remaining. The product should be maintained and

repaired in accordance with the manufacturer’s speciﬁcations, using

only the manufacturer’s authorized replacement parts, and should not

be modiﬁed from the manufacturer’s original design and conﬁguration.

ACCEPTABLE RIDING PRACTICES AND CONDITIONS

Always check and obey any local laws or regulations, which may

affect the locations where the electric motorbike may be used. Keep

safely away from cars and motor vehicle trafﬁc at all times, and only

use where allowed and with caution.

Do not activate the speed control on the hand grip unless you are on the

product and in a safe, outdoor environment suitable for riding.

The normal powered top speed of the Dirt Rocket will be approximately

14 mph (22 kmh), which can be affected by conditions, such as rider weight,

inclines, tire inﬂation and battery charge level. Avoid excessive speeds that

can be associated with downhill rides.

Maintain a hold on the handlebars at all times. Do not touch the brakes or

motor on your product when in use or immediately after riding as these parts

can become very hot.

Ride defensively. Watch out for potential obstacles that could catch your

wheel or force you to swerve suddenly or lose control. Be careful to avoid

pedestrians, skaters, skateboards, scooters, bikes, children or animals who

may enter your path, and respect the rights and property of others.

The Dirt Rocket is intended for use on ﬂat, dry surfaces, such as pavement or

level ground, without loose debris, such as sand, leaves, rocks or gravel. Wet,

slick, bumpy, uneven or rough surfaces may impair traction and contribute to

possible accidents. Do not ride your Dirt Rocket in mud, ice, puddles or water.

Watch out for potential obstacles that could catch your wheel or force you

to swerve suddenly or lose control. Avoid sharp bumps, drainage grates, and

sudden surface changes.

Do not attempt or do stunts or tricks on your Dirt Rocket. The Dirt Rocket is

not made to withstand abuse from misuse, such as jumping, curb grinding

or any other type of stunts. Racing, stunt riding, or other maneuvers also

enhance risk of loss of control, or may cause uncontrolled rider actions

or reactions.

Never allow more than one person at a time to ride the Dirt Rocket.

Do not ride at night or when visibility is limited.

Never use near steps or swimming pools.

Do not allow hands, feet, hair, body parts, clothing, or similar articles to

come in contact with moving parts, wheels, drivetrain, or chain while the

motor is running.

Never use headphones, a cell phone or text when riding.

Never hitch a ride with a vehicle.

Do not ride your Dirt Rocket in wet or icy weather and never immerse the

product in water, as the electrical and drive components could be damaged

by water or create other possibly unsafe conditions. Never risk damaging

surfaces, such as carpet or ﬂooring, by use of an electric motorbike indoors.

Safety Warnings ...........................................................................................1-2

Before You Begin.............................................................................................. 3

Assembly and Set-Up....................................................................................4-5

Charging the Battery ........................................................................................ 6

Pre-ride Checklist ............................................................................................. 6

Usage ............................................................................................................... 7

Repair and Maintenance.............................................................................7-10

Troubleshooting Guide ................................................................................... 11

Product Parts ................................................................................................. 12

Warranty ........................................................................................................ 14

SAFETY WARNINGS

PROPER RIDING ATTIRE

Always wear proper protective equipment, such as an approved safety helmet

(with chin strap securely buckled), elbow pads and kneepads. A helmet may

be legally required by local law or regulation in your area. A long-sleeved

shirt, long pants, and gloves are recommended. Always wear athletic shoes

(lace-up shoes with rubber soles) and keep shoelaces tied and out of the way

of the wheels, motor and drive system. Never ride barefooted or in sandals.

USING THE CHARGER

The charger supplied with the electric motorbike should be regularly examined

for damage to the cord, plug, enclosure and other parts. In the event of such

damage, the product must not be charged until the charger has been repaired

or replaced.

Use only with the recommended charger.

Use caution when charging.

The charger is not a toy. Charger should be operated by an adult.

Do not operate charger near ﬂammable materials.

Unplug charger and disconnect from product when not in use.

Always disconnect from the charger prior to wiping down and cleaning your

electric motorbike with damp cloth.

FAILURE TO USE COMMON SENSE AND HEED THE ABOVE

WARNINGS FURTHER INCREASES RISK OF SERIOUS INJURY. USE

AT YOUR OWN RISK AND WITH APPROPRIATE AND SERIOUS

ATTENTION TO SAFE OPERATION. USE CAUTION.

Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information

at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service

contact information is listed at the back of this manual.

BEFORE YOU BEGIN

Front Fork

Brake Lever

Remove contents from box. Remove the separators that protect the components from damage during shipping. Inspect the

contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping. Because the

Dirt Rocket is 95 percent assembled and packed at the factory, there should not be any problems, even if the box has a

few scars or dents.

MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY MAINTENANCE PROCEDURES.

Estimated Assembly and Set-Up Time

Razor recommends assembly by an adult.

Allow up to 15 minutes for assembly.

Allow up to 12 hours for initial charge (see page 6 for charging information).

WARNING:

DO NOT USE NON-RAZOR

PRODUCTS WITH YOUR RAZOR

DIRT ROCKET. The Dirt Rocket

has been built to certain Razor

design speciﬁcations. The

original equipment supplied at

the time of sale was selected

on the basis of its compatibility

with the frame, fork and all

other parts. Certain aftermarket

products may not be compatible

and will void your warranty.

Required Tools

Throttle

Chain Guard

Charger

(Note: Charger design may vary

from one shown)

PRODUCT I.D. CODE

1. Underneath Frame

2. Charger

3. Battery Cover

4. UPC Side of Box (not shown)

Plastic Bag Contents:

• Charger

• Tools

• Handlebar Clamps

• Owner’s Manual

5 mm and 6 mm

Allen Wrenches

Spoke Tightener10 mm Wrench

ASSEMBLY AND SET-UP

WARNING:

Failing to properly adjust and

tighten the bolts that afﬁx the

handlebars can cause you to lose

control and crash.

1 Place the handlebars in the

handlebar clamps.

2 Align parallel to the fork and

tighten the bolts using a 6 mm Allen

wrench. When properly tightened,

the handlebars should not move

forward or backward.

Align fender with the hole in the

fork and insert the bolt. Tighten

securely using a 10 mm wrench

and 5 mm Allen wrench.

Slip the cables through the slit on the

top of the number plate. Align the

number plate with the holes on the

fork and snap on the number plate.

Attaching the Handlebars

Tool Required: 6 mm Allen Wrench

Attaching the Front Fender

Tools Required: 10 mm Wrench and 5 mm Allen Wrench

Attaching the Number Plate

No tools required

Spoke

Flange

Nipple

Hub

Flange

Spoke

Flange

Rim

Nipple

Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information

at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service

contact information is listed at the back of this manual.

ASSEMBLY AND SET-UP

Using a bicycle tire pump equipped for

a Schrader valve, inﬂate both tires to

the PSI indicated on the sidewall of

the tire.

Checking Spoke Tension

Verify the spoke tension by grasping and shaking each spoke. Spoke

should not be loose from hub. Look for any play between the spoke ﬂanges

where it mates with the hub. Try to turn the nipple using your ﬁngers. You

should not be able to spin any nipple by hand. If one or more spokes is loose,

all spokes should be checked and tightened with a spoke tightener.

2 Start with spoke closest to the

tire valve stem and tighten each

nipple, in sequence, exactly 1/4

to 1/2 turn. A single 1/4 to 1/2

turn may not be enough to bring

the spokes into proper tension.

Continue tightening all spokes no

more than 1/2 turn in sequence

until all spokes are tight.

Note: More than a 1/2 turn each

can cause the wheel to become

distorted and wobbly, thus

permanently damaging the wheel.

Inﬂating the Tires

Tires are inﬂated when shipped, but they invariably lose some pressure between the point of manufacturing and

your purchase. Inﬂate the tires to the correct PSI before ﬁrst time use.

Lower air pressure can result in a shorter ride time.

Periodically check both tires. Reinﬂate when needed.

WARNING:

Do not use the Dirt Rocket for the

ﬁrst time until you have inﬂated the

tires to the correct PSI. Failure to do

so may damage your motor bike and

void your warranty.

WARNING:

Do not over inﬂate, as this could

damage the tire or wheel.

Note: The pressurized air supplies

found at gasoline stations are

designed to inﬂate high-volume

automobile tires. If you decide to

use such an air supply to inﬂate

your tires, ﬁrst make sure the

pressure gauge is working, then

use very short bursts to inﬂate to

the correct PSI. If you inadvertently

over-inﬂate the tire, release the

excess pressure immediately.

PRE-RIDE CHECKLIST

CHARGING THE BATTERY

2 Make sure the power switch

is in the OFF position. Plug the

charger into the charger port

on the product. The light on the

charger should turn red during

charging. The light will turn green

when the charging is complete.

1 Plug the charger plug into wall

outlet. The light on the charger

should be green.

Note: If green light (LED) does not

turn on, try a different outlet

Note: Make sure power is turned

OFF when unit is not in use. If

the power switch is left on for an

extended period of time, the battery

may reach a stage at which it will

no longer hold a charge.

Charger

LED

Brake

Check the brake for proper function. When you squeeze the

lever, the brake should provide positive braking action. When

you apply the brake with the speed control on, the brake cut-off

switch will stop the motor.

Tires

Periodically inspect the tires for excess wear and replace as

needed. Regularly check the tire pressure and inﬂ ate as needed.

If you get a ﬂ at tire, the inner tube can be patched or a new tube

can be purchased from Razor or an authorized repair center.

Frame, Fork and Handlebars

Check for cracks or broken connections. Although broken frames

are rare, it is possible for an aggressive rider to run into a curb

or object and wreck, bend or break the frame. Get in the habit of

inspecting your product on a regular basis.

Hardware/Loose Parts

Before every ride, check all parts, such as nuts, bolts, cables,

fasteners, etc., to ensure they are secure and assembled correctly.

There should not be any unusual rattles or sounds from loose

parts or broken components. If the unit is damaged, do not ride.

Reference “Safety Warnings” on pages 1 and 2 of this

manual.

Safety Gear

Always wear proper protective gear, such as an approved safety

helmet. Elbow pads, kneepads, pants and long sleeves are

recommended. Always wear closed toe shoes (lace-up with rubber

soles) and keep shoelaces tied and out of the way of the wheels,

motor and drive system. NEVER RIDE BAREFOOTED OR

IN SANDALS.

Laws and Regulations

Always check and obey any local laws or regulations.

Insurance

Do not assume that your existing insurance policies necessarily

provide coverage for electric product use. Check with your

insurance company for information regarding insurance.

WARNING:

Use ONLY with the recommended

charger. Batteries are only to be

charged under adult supervision.

The charger is not a toy. Always

disconnect the charger before

wiping down and/or cleaning the

Dirt Rocket with a damp cloth.

The charger supplied with the

Dirt Rocket should be regularly

examined for damage to the cord,

plug, enclosure and other parts. In

the event of such damage, the Dirt

Rocket must not be charged until it

has been repaired or replaced.

Chargers have built-in overcharge

protection to prevent battery from

being overcharged.

Note: If the charger gets warm

during regular use, this is a normal

response and is no cause for

concern. If your charger does not get

warm during use, it does not mean

that it is not working properly.

Wall outlet - Green (stand by)

Wall outlet and Unit - Red (Charging)

Charging complete - Green (Charged)

Note: Continue charging unit even if

light turns green prior to 12 hours.

WARNING: Battery charge

can deplete over time. Periodically

recharge battery when not in use.

Your Dirt Rocket may not have a fully charged battery; therefore you must charge the battery prior to use.

• Initial charge time: 12 hours.

• Recharge time: up to 12 hours, even if the light turns green.

Recommended maximum charging time is 24 hours.

• Always charge the battery immediately after riding.

• Fully charge battery before storing for extended

periods of time.

• Unplug charger from the wall outlet when not in use.

• Failure to recharge battery periodically may result in a

battery that will not accept a charge.

• Make sure the Dirt Rocket’s power switch is turned OFF

when unit is not in use. If the power switch is left on

for an extended period of time, the battery may reach a

stage at which it will no longer hold a charge.

• To ensure long battery life, never store the product in

freezing or below freezing temperatures! Freezing will

permanently damage the battery.

• Run time: Up to 40 minutes of continuous ride time.

Run time may vary depending on riding conditions, rider

weight, climate, and/or proper maintenance.

• Constant stopping and starting may shorten ride time.

• Battery life can vary depending on proper maintenance

and usage of the unit.

Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information

at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service

contact information is listed at the back of this manual.

1 To adjust the tension, thread

the brake lever adjuster in or out

1/4 to 1/2 turn until the desired

brake adjustment is attained. Most

adjustments are complete at this

step. If brake still needs further

adjustment, proceed to step 2.

2 If the brake has too much slack,

use a 10 mm wrench to loosen the

brake anchor cable for additional

adjustment and retighten.

WARNING:

The brake is capable of causing the

electric motorbike to skid the tire,

throwing an unsuspecting rider.

Practice in an open area free from

obstacles until you are familiar with

the brake function. Avoid skidding to

a stop as this can cause you to lose

control or damage the rear tire.

Note: The brake lever contains a

safety switch to cut power to the

motor when the brake is applied. In

an emergency, applying the brake

will always stop the product from

moving. Do not disable or replace

this lever with anything other than a

genuine Razor replacement part.

Testing the Brake

To use the brake, squeeze the lever to increase the pressure on the brake. The brake lever is ﬁ tted with a cable

adjuster to compensate for cable stretch and/or to ﬁ ne-tune the lever movement to engage the brake. If brake is

not engaging properly, follow instructions for adjusting the brake outlined below.

Adjusting the Brake

Tool Required: 10 mm Wrench

Starting the Dirt Rocket

Place both hands on the handlebars. Slowly push forward with one foot and

apply the throttle.

Note: Keep both feet on the foot pegs when unit is in motion.

Stopping the Dirt Rocket

Release the throttle and apply the brake.

Note: When coming to a complete stop, place both feet on the ground to

balance the unit.

REPAIR AND MAINTENANCE

USAGE

Turn power switch “OFF” before beginning repair or maintenance:

• Read the instructions

• Remove charger plug

• Turn the power switch off

• Secure the unit under repair

• Exercise caution around

exposed parts

• Contact Razor customer service

if unsure about any repair or

maintenance

Chain

Tensioner

Chain

Tensioner

Nut

Cable Guide

Bracket

Spacer

Frame

Washer

Bolt

Brake Plate

17-1

17-2

17-3

17-2

17-1

17-3

17-2

17-4

17-2

REPAIR AND MAINTENANCE

4 With two (2) 15 mm wrenches,

loosen the axle. Push the chain

tensioner down to loosen the chain

and remove wheel.

5 Install the chain onto the rear

wheel sprocket. Slip wheel axle into

the frame slots. Push the chain ten-

sioner down to create slack in chain.

Hand tighten rear axle locknuts.

6 Verify chain is properly installed

on each sprocket and tensioner is

correctly positioned at the bottom of

the chain.

8 Thread the brake cable through

the brake adjuster barrel, through

the large spring, and into the small

hole in the side of the anchor bolt.

Position the cable to the original

location (as indicated by the slight

cable kink) and tighten securely.

7 Install the cable guide

bracket to the frame and brake

plate using bolt, washers, and

nut. Do not tighten.

9 Tighten the cable guide bracket

bolt. Tighten the locknuts on the

rear axle. Test the brake to verify

proper function before riding.

Readjust as needed.

Chain and Rear Wheel Replacement

Tools Required: Phillips Screwdriver, 10 mm Wrench, two (2) 8 mm Wrenches, and two (2) 15 mm Wrenches.

2 With a 10 mm wrench, loosen

the brake cable anchor bolt and

disconnect the cable.

3 With two (2) 8 mm wrenches

remove the cable guide bracket from

the frame and brake plate. Keep the

spacer and washers together.

1 Using a Phillips screwdriver

remove the screws on chain guard

and remove.

Note the hardware sequence

(from outside toward the center).

Left Side (Brake)

17-1 15 mm Flange Locknut

17-2 Flat Washer

Frame

17-3 Washer

17-4 Brake Plate

Right Side (Throttle)

17-1 15 mm Flange Locknut

17-2 Flat Washer

Frame

17-3 Washer

Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information

at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service

contact information is listed at the back of this manual.

Replacing the Fuse

Tools Required: 5 mm Allen Wrench, Phillips Screwdriver, and 8 mm Wrench

WARNING:

To prevent shock, please follow the

instructions accordingly and do not

skip or combine any steps.

1 Twist the black plastic cap

and remove.

4 On the opposite side of the

charger port, locate and remove the

ﬁve (5) Phillips screws and lock nuts

on the battery cover using a Phillips

screwdriver and 8 mm wrench.

Separate and remove cover.

2 Using a 5 mm Allen wrench,

remove the bolt.

5 Locate the fuse box attached

to the batteries. Open the fuse

cover to expose the fuse.

3 Using a 5 mm Allen wrench,

loosen the two (2) bolts

underneath the rear of the seat

and remove the fairing.

6 Remove the fuse and replace

with a new one of equal

amperage. Close the fuse cover

and reattach the battery cover,

fairing, and plastic cap.

30 Amp

REPAIR AND MAINTENANCE

Front Wheel Replacement

Tools Required: Phillips Screwdriver and 15 mm Wrench

1 Using a Phillip screwdriver,

loosen the two (2) screws on

the fork covers (2 per side) and

remove covers.

2 Remove the nuts on both sides

of the front axle using a 15 mm

wrench then remove the axle

safety washers.

3 Remove front wheel and

install replacement wheel.

Re-attach fork covers.

Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information

at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service

contact information is listed at the back of this manual.

WARNING:

If a battery leak develops, avoid

contact with the leaking acid and

place the damaged battery in a

plastic bag. Refer to the disposal

instructions at left. If acid comes

into contact with skin or eyes, ﬂush

with cool water for at least 15

minutes and contact a physician.

WARNING: Battery posts,

terminals and related accessories

contain lead and lead compounds.

Wash your hands after handling.

Battery Care and Disposal

Do not store in freezing or below freezing temperatures. To properly maintain your battery and ensure maximum battery

life, carefully read the “Charging the Battery” section on page 6 of this owner’s manual.

CONTAINS SEALED NON-SPILLABLE LEAD BATTERIES. BATTERIES MUST BE RECYCLED.

Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an

environmentally sound manner. Do not dispose of a lead-acid battery in a ﬁre. The battery may explode or leak. Do not

dispose of a lead-acid battery in your regular household trash. The incineration, land ﬁlling or mixing of sealed lead-

acid batteries with household trash is prohibited by law in most areas. Return exhausted batteries to a federal or state

approved lead-acid battery recycler or a local seller of automotive batteries. If you live in Florida or Minnesota, it is

prohibited by law to throw away lead-acid batteries in the municipal waste stream.

Charger

The charger supplied with the product should be regularly examined for damage to the cord, plug, enclosure and other

parts, and in the event of such damage, the electric motorbike must not be charged until it has been repaired or replaced.

Use ONLY with the recommended charger.

Wheels

Wheels and drive system are subject to normal wear and tear. It is the responsibility of the user to periodically inspect

wheels for excess wear and adjust and replace drive train components as required.

Replacement Parts

The most frequently requested replacement parts are available for purchase at some Razor retail partners.

For the complete selection of replacement parts visit shop.razor.com.

Service Centers

For a list of authorized Razor repair centers:

• Check online at www.razor.com.

• Additional Customer Service contact information is listed on the back of this manual.

REPAIR AND MAINTENANCE

TROUBLESHOOTING

Problem Possible Cause Solution

Electric motorbike does not run Undercharged battery

Loose wires or connectors

Charge the battery. A new battery should have been charged for at least 12 hours

before using the electric motorbike for the ﬁrst time and up to 12 hours after each

subsequent use.

Check all connectors. Make sure the charger connector is tightly plugged into the

charging port, and that the charger is plugged into the wall.

Make sure power ﬂow to the wall outlet is on.

Check all wires and connectors to make sure they are tight.

The fuse will burn out and automatically shut off the power if the motor is overloaded.

Electric motorbike was running

but suddenly stopped

Burned-out fuse An excessive overload, such as too heavy a rider or too steep a hill, could cause the

motor to overheat. Replace the fuse with a new one of equal amperage. Correct the

conditions that caused the fuse to burn out and avoid repeatedly burning out fuse

(Refer to page 9 of this manual).

Contact your local Razor authorized service center for diagnosis and repair.

Short run time (less than

15 minutes per charge)

Motor or electrical switch damage

Undercharged battery

Tires are not properly inﬂated

Battery is old and will not accept

full charge

Brakes are not adjusted properly

Charge the battery. A new battery should have been charged for at least 12 hours

before using the electric motorbike for the ﬁrst time and up to 12 hours after each

subsequent use.

Check all wires and connectors. Make sure the battery connector is tightly plugged

into the charger connector, and that the charger is plugged into the wall.

The tires are inﬂated when shipped but they invariably will lose some pressure

between the point of manufacturing and your purchase. Refer to instructions on

page 5 of this manual to properly inﬂate tires.

Even with proper care, a rechargeable battery does not last forever. Average battery

life is 1 to 2 years depending on product use and conditions. Replace only with a

Razor replacement battery.

Refer to brake adjustment instructions on page 7 of this manual.

Electric motorbike runs

sluggishly

Riding conditions are too stressful

Tires are not properly inﬂated

Electric motorbike is overloaded

Use only on solid, ﬂat, clean and dry surfaces, such as pavement or level ground.

The tires are inﬂated when shipped, but they invariably will lose some pressure

between the point of manufacturing and your purchase. Refer to instructions on

page 5 of this manual to properly inﬂate tires.

Make sure you do not overload the electric motorbike by allowing more than one

rider at one time, exceeding the maximum weight limit, going up too steep a hill or

towing objects behind the product.

Sometimes the product doesn’t

run, but other times it does.

Loose wires or connectors

Motor or electrical switch damage

Check all wires around the motor and all connectors to make sure they are tight.

Contact your local Razor authorized service center for diagnosis and repair.

Electric motorbike does not stop

when applying the brake

Brakes are not adjusted properly Refer to instructions on page 7 of this manual to properly adjust brakes.

Electric motorbike makes loud

noises or grinding sounds

Chain is too dry. Apply a lubricant such as 3 in 1

™

or Tri-Flow

™

to the chain.

For more troubleshooting tips, a list of available replacement parts or to locate an authorized Service Center in your area,

visit our website at www.razor.com or call toll free +1 866 467 2967 to speak to a live Customer Service Representative

*Unit(s) should be turned off and fully charged prior to doing any Troubleshooting

NOTE: All troubleshooting steps should be performed by an adult only

12-1234

11 12 13 15 16

17 18 19

5 14

Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information

at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service

contact information is listed at the back of this manual.

MX350/MX400 PARTS

Keep your MX350/MX400 running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability.

(Speciﬁcations subject to change without notice.)

1. Handlebar Grips (Right/Left)

2. Single Speed Twist Grip Throttle

2-1. Sleeve

3. Handlebar

4. Brake Lever Assembly

5. Handlebar Clamp (Upper/Lower)

6. Front Wheel Complete

7. Front Fork

8. Front Fender

9. Fork Cover (Right/Left)

10. Battery (2- 12V/7Ah) with 30 Amp Fuse

11. Battery Cover (Right/Left)

12. On/Off Switch

13. Charger Port

14. Control Module

15. Kickstand

16. Motor (24V/250W)

17. Rear Wheel Complete

18. Chain

19. Chain Guard

20. Seat Fairing

NOTICE: INSURANCE

YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR

ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC

RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED,

YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.

Printed in China for:

Razor USA LLC

PO Box 3610

Cerritos, CA 90703

are among the registered trademarks of Razor USA LLC in the United States and/or select

foreign countries. Dirt Rocket is a trademark of Razor USA LLC.

US_150526

DISTRIBUTED IN THE UK BY:

Re:creation Limited

2 Meadows Business Park

Station Approach, Blackwater

Camberley, Surrey GU17 9AB

United Kingdom

+44 (0) 118 973 6222 Tel

+44 (0) 118 973 6220 Fax

[email protected]

DISTRIBUTED IN AUSTRALIA BY:

Funtastic Limited

Level 2, Tower 2, Chadstone Place

1341 Dandenong Road

Chadstone VIC 3148

Australia

+1 800 244 543

[email protected]

FCC COMPLIANCE

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations to this unit not expressly approved by Razor USA, could void the user’s authority to operate the equipment.

WARRANTY

Razor Limited Warranty

The manufacturer warranties this product to be free of manufacturing

defects for a period of 90 days from date of purchase. This Limited Warranty

does not cover normal wear and tear, tire, tube or cables, or any damage,

failure or loss caused by improper assembly, maintenance, storage or use of

the Razor Dirt Rocket.

This Limited Warranty will be void if the product is ever:

• used in a manner other than for recreation or transportation;

• modiﬁed in any way;

• rented.

The manufacturer is not liable for incidental or consequential loss or damage

due directly or indirectly to the use of this product.

Razor does not offer an extended warranty. If you have purchased an extended

warranty, it must be honored by the store at which it was purchased.

For your records, save your original sales receipt with this manual and write

the serial number below.

__________________________________________

CUSTOMER SERVICE CONTACT INFORMATION

UNITED STATES

Razor USA LLC

P.O. Box 3610

Cerritos, CA 90703

USA

+1 866 467 2967

Monday - Friday

8:00 AM - 5:00 PM Paciﬁc Time

ASIA

Razor USA (Asia)

P.O. Box 3610

Cerritos, CA 90703

USA

+81 50 7579 6622

info@razor-asia.com

EUROPE

Razor USA (Europe)

Handelsweg 2

2742 RD Waddinxveen

Netherlands

+44 (0) 1202 672702

Need Help? Visit our web site for replacement parts, product support, a list of authorized service centers in the US and customer service contact information

at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service

contact information is listed below: