Vileda 148633 Owner's manual

Brand: Vileda

Model: 148633

Category: Robotic vacuum cleaners

Type: Owner's manual

This manual is also suitable for

Cleaning Robot M-488A

Vileda 148633 is an advanced robotic cleaning solution designed to make your life easier. With its powerful vacuum and rotating brushes, it effectively removes dirt, hair, and particles from all types of hard floors and even short-pile carpets. The device is equipped with cliff sensors to prevent falls and can navigate around obstacles, ensuring a thorough clean. Choose from three cleaning modes (short, medium, and large) to customize the cleaning time to the size of the room. Additionally, the side brush helps sweep dirt from corners and edges, leaving your floors spotlessly clean.

M-488A Cleaning Robot

Owner’s Manual

Dear Owner,

Thank you for purchasing your new Vileda Cleaning Robot.

After many years of studying consumer needs, we have designed

this cleaning robot to make your life easier and more enjoyable. At

one press of a button, the Vileda Cleaning Robot moves by itself

around your home, picking up particles, dust and hair from your

ﬂoors, even under furniture and other hard to reach places such as

corners and edges. The Vileda Cleaning Robot works eﬃciently on

all kinds of hard ﬂoors, and even on short-piled carpets.

We believe we have produced the most stylish and easy to use tool

to help you with your everyday cleaning tasks.

Enjoy it!

CONTENTS

General Warnings Pg 4

Part Location Pg 7

Anatomy Pg 8

Battery Charging & Recharging Pg 9

Using the Product Pg 10

Cleaning Modes Pg 10

Cleaning System Pg 11

Removing and Emptying the Dust Bin Pg 12

Cleaning Dust Bin & Filter Pg 12

Cleaning Main Brushes Pg 13

Cleaning Vacuum Inlet Cover Pg 14

Replacing Side Brush Pg 14

Troubleshooting Pg 15

Environmental and Product Recycling Pg 16

Battery Removal Pg 17

Technical Speciﬁcation Pg 17

Guarantee Information Pg 18

GENERAL WARNINGS

IMPORTANT:

READ ALL INSTRUCTIONS BEFORE USE.

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

WARNING:

USE THE UNIT ONLY AS DESCRIBED IN THIS MANUAL. FAILURE TO FOL−

LOW ALL INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC

SHOCK, FIRE AND/OR SERIOUS INJURY.

WHEN USING ANY ELECTRICAL APPLIANCE, BASIC SAFETY PRECAU−

TIONS SHOULD ALWAYS BE OBSERVED, INCLUDING THE FOLLOWING,

IN ORDER TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, LEAK−

ING BATTERIES OR PERSONAL INJURY.

USE RESTRICTIONS

• Only for indoor use. Do not use outdoors or on balconies.

• Intended for domestic use only.

• Device is not a toy. Do not sit or stand on it. Small children and pets

should be supervised when the robot is cleaning.

• Do not pick up anything that is ﬂammable, burning or smoking.

• Do not use this device to pick up anything wet.

• Do not use with long-piled carpets.

PERSONAL SAFETY

• The intended use is described in this manual. The use of any accesso-

ry or attachment or the performance of any operation with this appliance

other than those recommended in this instruction manual may present a

risk of personal injury.

• Children and animals must be supervised to ensure they do not play with

the appliance.

• This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack of

GENERAL WARNINGS

experience and knowledge if they have been given supervision or instruc-

tion concerning use of the appliance in a safe way and understand the

hazards involved.

• Children shall not play with the appliance.

• Cleaning and user maintenance shall not be made by children without

supervision.

• Store in a dry place.

• Store out of reach of children.

• Use only with the attachments recommended by the manufacturer.

• Do not use without the ﬁlter in place.

• Keep the product and all accessories away from hot surfaces.

• Do not immerse the appliance in water or other liquid.

ELECTRICAL SAFETY INSTRUCTIONS

• Never modify the charger in any way.

• The charger has been designed for a speciﬁc voltage. Always check that

the mains voltage is the same as that stated on the rating plate.

• Only use the charger supplied with the product. Do not attempt to use the

charger with any other product nor attempt to charge this product with

another charger.

• Before use, check the charger cord for signs of damage or ageing.

• Do not abuse the charger cord; never carry the charger or charger stand

by the cord.

• Never pull the charger cord to disconnect from a socket; grasp the charg-

er and pull to disconnect.

• Keep the charger cord away from hot surfaces and sharp edges.

• Do not handle the charger or the unit with wet hands.

• Do not store or charge the unit outdoors.

• Unplug the charger before cleaning.

Product contains electronic parts. DO NOT submerge it or spray it with

water. Clean with a dry cloth only.

GENERAL WARNINGS

BATTERY USE AND CARE

• Using a charger from a diﬀerent product may cause a risk of ﬁre.

• Leaks from battery cells can occur under extreme conditions. If the liq-

uid gets on the skin, wash it immediately with soap and water. If the liquid

gets into the eyes, ﬂush them immediately with clean water for a minimum

of 10 minutes and seek medical attention.

• This product contains NiMH batteries. Do not incinerate batteries or ex-

pose to high temperatures, as they may explode.

• When the battery pack is not in use, keep away from other metal objects

such as: paper clips, coins, keys, nails, screws or other small metal ob-

jects that can make a connection from one terminal to another.

• Shorting the battery terminals may cause ﬁre.

• The battery must be removed from the appliance before it is discarded.

• The battery is to be disposed of safely.

• The appliance must be disconnected from the mains supply when remov-

ing the battery.

• In an emergency situation contact professional help immediately!

SERVICE

• Before using the machine and after any impact, check for signs of wear or

damage and repair as necessary.

• Do not use the appliance if any part is damaged or defective.

• Repairs should be carried out by a service agent or a suitably qualiﬁed

person in accordance with relevant safety regulations. Repairs by unqual-

iﬁed persons could be dangerous.

• Never modify the appliance in any way as this may increase the risk of

personal injury.

• Only use replacement parts or accessories provided or recommended

by the manufacturer.

PART LOCATION

A. 1 Main Unit

B. 1 Battery Charger (* Picture may diﬀer from provided box content)

C. 1 Rechargeable Battery Pack (installed)

D. 1 Filter Mesh (extra)

E. 1 Side Brush (extra)

F. 1 Maintenance Brush

ANATOMY

1. Infrared Sensor

2. Handle

3. Battery Charging Indicator

4. Command Buttons

5. Removable Dust Bin

6. Rechargeable Battery

7. Cliﬀ Sensors

8. Side Brush

9. Power Switch

10. Main Rotating Brush

11. Filter

12. Vacuum Inlet Cover

13. Battery Charger Socket

BATTERY CHARGING & RECHARGING

hours

Charge the battery

for 8 hours before

ﬁrst use.

BATTERY CHARGING & RECHARGING

WARNING: if the battery is damaged in any way do not attempt to re-

charge it. Contact Vileda in the UK on 08457697356.

1 Connect the supplied battery charger into the battery charging socket

located beside the power switch.

2 Once the battery is fully charged unplug the charger from the battery

charging socket (13). Do not pull the charger cord, grasp the charger and

pull to disconnect from the socket.

Note: charging time is about 4-5 hours.

Battery autonomy is up to 80 minutes. Battery charging indicator will turn

red when battery level is down. Then recharging is needed.

To maintain peak performance of the battery it is recommended to charge

8 hours before ﬁrst use or when used again after a long time.

WARNING: Only use a replacement battery as supplied by the manufac-

turer.

USING THE PRODUCT CLEANING MODES

USING THE PRODUCT

Before using, pick up objects like clothing, loose papers, pull cords for

blinds or curtains, power cords, and any fragile objects as they may

entangle with the cleaning brushes. If the device passes over a power

cord and drags it, there is a chance an object could tumble off a table

or shelf.

1 Ensure the battery is charged.

2 Place Vileda Cleaning Robot in the middle of the room.

3 To turn Vileda Cleaning Robot ON press the main Power Switch.

4 To START Vileda Cleaning Robot, press one of the Command Buttons

to choose the desired cleaning mode (see section “Cleaning Modes”).

5 To PAUSE Vileda Cleaning Robot, press one of the Command Buttons.

6 To RESUME Vileda Cleaning Robot, press one of the Command Buttons

again.

7 To turn Vileda Cleaning Robot OFF, press the main power Switch.

IMPORTANT: For most eﬃcient cleaning, keep your ﬂoors as clear as pos-

sible (e.g. temporarily remove wires, rugs, chairs, small objects, …). With

less obstacles, the Vileda Cleaning Robot will move faster and clean more

eﬀectively.

CLEANING MODES

WARNING: Certain types of ﬂoors and stairs could reduce the reliability of

drop sensors - Test with your speciﬁc ﬂoor and stairs before use.

START

TABLE

SOFA

CLEANING SYSTEM

Vileda Cleaning Robot can avoid obstacles and is equipped with cliﬀ sensors

to avoid falling down the stairs.

Vileda Cleaning Robot has 3 cleaning modes: SHORT (S), MEDIUM (M)

and LARGE (L), which represent the size of the room.

• SHORT (S): robot cleans for 5 minutes.

Ideal for spot cleaning in one area.

• MEDIUM (M): robot cleans for 30 minutes.

Ideal for mid-sized rooms (up to 25 m

• LARGE (L): robot cleans for 60 minutes.

Ideal for big rooms (more than 25 m

CLEANING SYSTEM

1 Side brush sweeps into corners and along edges.

2 Two rotating brushes pick up dirt, hair and particles into the dustbin.

3 Vacuum power picks up the remaining ﬁne dirt.

Vileda Cleaning Robot works on all hard ﬂoors such as wood, parquet, tiles,

linoleum and short-pile carpets.

Do not use Vileda Cleaning Robot with long-piled carpets.

REMOVING AND EMPTYING THE DUST BIN

2 4 5

REMOVING AND EMPTYING THE DUST BIN

1 Turn oﬀ the power switch.

2 Press down the dust bin release button and pull out the dust bin as indi-

cated in illustrations.

3 Empty the dust bin in the rubbish bin.

4 Reinsert dust bin and push until you hear a clicking sound.

CLEANING DUST BIN AND FILTER

1 Turn dust bin upside down.

2 Press bottom slightly and take ﬁlter mesh out as indicated in illustrations.

3 Clear the dirt on the ﬁlter mesh.

4 Reinsert ﬁlter mesh back to the dust bin.

5 Press slightly until it clips.

6 Reinsert dust bin in the robot.

2 4

PRESS

CLEANING MAIN BRUSHES

3 5

Product contains electronic parts. Do not submerge it or spray it with wa-

ter. Clean with a dry cloth only.

WARNING: to buy new ﬁlters, please contact Vileda in the UK on

08457697356.

CLEANING MAIN BRUSHES

1 Turn oﬀ the power switch and turn the robot upside down on a ﬂat sur-

face.

2 Use a cross-head screwdriver to remove the ﬁxing screw on the right.

3 Take out the main brush, rubber brush and brush coupler together as

shown in the illustration.

4 Remove all hair and dirt from both brushes. Clean brushes chamber.

5 Wipe out dirt on the metal shaft and bearing of the brush coupler as indi-

cated in the illustration.

6 Put brush coupler and brushes back.

7 Tighten the screw.

Main brushes do not need to be cleaned after each use. However, reg-

ular cleaning is recommended to avoid excessive build up of hair that

could damage the robot.

CLEANING VACUUM INLET COVER

1 Turn oﬀ the power switch and turn the robot

upside down.

2 Remove vacuum inlet cover as shown in the

illustration.

3 Clean vacuum inlet cover and the fan mechanism

to ensure good ventilation.

4 Reinsert the vacuum inlet cover by guiding the

hinge tabs back into the holes carefully.

REPLACING SIDE BRUSH

1 Use a cross-head screwdriver to remove side brush cover.

2 Insert new side brush and put back the cover.

3 Tighten the screws.

For further help, technical advice, or to order spare or replacement parts

please contact Vileda in the UK on 08457697356.

TROUBLESHOOTING

Problem Possible reason Possible solution

Robot does not

detect cliﬀs /

drops.

• Sensors are dirty. • Wipe away dust from

sensors with a dry

cloth.

Robot stops while

cleaning and all

light indicators

turn on.

• Main brushes are

blocked.

• Main brushes are

jammed.

• Clean main brushes

and restart.

• Remove jam and

restart.

Robot stops and

battery charge

indicator is on.

• Low battery. • Recharge battery.

Robot only moves

in circles in the

same position.

• One wheel is blocked. • Remove hairs and dirt

from wheels.

Battery does not

recharge.

• Battery is not installed

correctly.

• Charger is not

plugged correctly.

• Reinstall battery.

Two beeps should be

heard when installed

properly.

• Check charger is

plugged correctly to

the outlet and to the

robot.

For further help, technical advice, or to order spare or replacement parts

contact Vileda in the UK on 08457697356.

ENVIRONMENTAL AND PRODUCT RECYCLING

The Vileda Cleaning Robot fulﬁls the EU directive 2002/96/CE, covering

electrical and electronic appliances and the management of its disposal.

The packaging material is entirely recyclable, and marked with the recy-

cling symbol. Follow local regulations for scrapping. Keep the packaging

materials (plastic bags, polystyrene parts, etc.) out of the reach of children,

as they are potentially dangerous.

When the product has reached the end of its life please do not dispose of

it with general household waste. To prevent possible harm to the environ-

ment or human health from uncontrolled waste disposal, recycle it respon-

sibly to promote the sustainable reuse of material resources.

The symbol identiﬁes the Vileda Cleaning Robot as a product submit-

ted to the regime of selective electrical appliance recycling collection.

The product contains a NiMH battery which should not be disposed of with

general household waste. Call, or deposit the battery in an oﬃcial collec-

tion point for its recycling.

Batteries can be detrimental for the environment and can explode if they

are exposed to high temperatures.

The violation of these precautions could cause ﬁre and / or serious injuries.

For more detailed information about treatment, recovery and recycling of

this product, please contact your local city oﬃce, your household waste

disposal service or the shop where you purchased the product.

BATTERY REMOVAL TECHNICAL SPECIFICATION

BATTERY REMOVAL

At the end of the product’s or battery’s life the battery should be removed

for disposal and recycling.

Follow these instructions to remove and reinstall the battery:

1 Turn oﬀ the power switch and turn the ro-

bot upside down.

2 Push both ﬂaps inwards and pull up until

battery pack comes out.

3 Reinstall battery by pushing until you hear

a clicking sound.

WARNING: NEVER touch both the metal battery terminals at the same

time with any metal objects as this will short circuit the battery and may

create sparks that can cause small burns.

TECHNICAL SPECIFICATION

Battery type 14.4V DC, 1700 mAh NiMH

Charging time 4-5 hours

Charger output 24V DC

Charger input 100-240V AC

Unit Average Power 19W ~ 25W

Suction Power 3.00W

Airﬂow 63.6dm

/min

Dust Capacity 0,25L

Unit Size 34cmx9cm

GUARANTEE INFORMATION

2 Year Limited Guarantee:

Vileda Customer Support

Freudenberg Household Products

Vileda House

2 Chichester Street

Rochdale, Lancashire

OL16 2AX

www.vileda.co.uk

Customer Care Line: 08457697356

FHP Export GmbH

69448 Weinheim

The present guarantee is only valid for the Vileda Cleaning Robot.

The Vileda Cleaning Robot guarantee complies with the directive 1999/44/

CE.

Vileda guarantees that the Cleaning Robot will be free of defects due to

defective materials or manufacture. If defects arise during the period of

guarantee, Vileda will guarantee the replacement of the defective part or

provide a new unit.

IMPORTANT: Please keep your purchase receipt! Vileda will repair the ro-

bot or will replace some of its pieces or the entire product only if proof of

purchase is provided and the claim is within the period of guarantee.

The Vileda limited guarantee of 2 years does not cover non authorized re-

pairs.

The limited guarantee does not include batteries.

The limited guarantee will automatically come to an end 2 years after the

purchase date.

The guarantee will be annulled if the product is not used as indicated in the

instructions manual, including, as an example:

1 If it has been damaged due to incorrect use or maintenance.

2 If any part is modiﬁed or replaced or if it is used in any way that is not

recommended by Vileda.

GUARANTEE INFORMATION

3 If it is used with any parts not produced or not recommended by Vileda.

4 If it is used for purposes other than those speciﬁed by Vileda. If used

outdoors or for commercial purposes.

If after following the manual, you are sure that the product is defective, call

Vileda on 08457697356. Be ready with the product, a complete descrip-

tion of the problem, proof of purchase, your name, address and telephone

number.

Vileda does not take responsibility for consequential or indirect damages

caused by the use of the product. The total liability of Vileda for all losses

and damages howsoever caused shall not exceed the purchase price of

the product. If you have any doubts referring to the correct use of the prod-

uct or referring to the guarantee, call Vileda Customer Service.

Vileda Customer Support

Freudenberg Household Products

Vileda House

2 Chichester Street

Rochdale, Lancashire

OL16 2AX

www.vileda.co.uk

FHP Export GmbH

69448 Weinheim

04048-72-26-204

Vileda 148633 Owner's manual

Brand: Vileda

Model: 148633

Category: Robotic vacuum cleaners

Type: Owner's manual

This manual is also suitable for

Cleaning Robot M-488A

Download PDF

report

Vileda 148633 Owner's manual

This manual is also suitable for

Vileda 148633 Owner's manual

Related papers

Other documents