VOLTCRAFT 51 42 02 Operating Instructions Manual
- Type
- Operating Instructions Manual
Page is loading ...
Page is loading ...
OPERATING INSTRUCTIONS
VERSION 04/11
FPPS 5-12WPC PLUG-IN POWER ADAPTER
ITEM NO.: 51 42 02
INTENDED USE
This product is designed for powering low voltage consumers with a car adapter. The
load’s current consumption must not exceed the output current of the product. Due to
its interchangeable power plug adapters, the product can be used worldwide. If the
power adapter is overloaded (e.g. through short circuit or too high a continuous current
consumption), the output is automatically lowered. Power is supplied via a standard mains
socket (100 – 240 V/AC, 50/60 Hz). The product should only be used in dry indoor areas.
This product fulls European and national requirements related to electromagnetic
compatibility (EMC). CE conformity has been veried and the relevant statements and
documents have been deposited at the manufacturer.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If
you use the product for purposes other than those described above, the product may be
damaged.Inaddition,improperusecancausehazardssuchasshortcircuiting,re,electric
shock etc. Read the instructions carefully and keep them. Make this product available to third
parties only together with its operating instructions.
DELIVERY CONTENT
Power adapter•
4 x power plug adapter•
Operating instructions•
SAFETY INSTRUCTIONS
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
Persons / Producta)
The product is not a toy and should be kept out of reach of children!•
When used in conjunction with other devices, observe the operating instructions •
and safety notices of connected devices.
The product must not be subjected to heavy mechanical stress.•
The product must not be exposed it to extreme temperatures, direct sunlight, •
intense vibration, or dampness.
Take care not to damage or destroy its insulation.•
Never use the power adapter as a charging device proper.•
When using power adapters you are not allowed to wear metallic or conductive •
pieces of jewelry, e.g. chains, bracelets, rings or the like.
Power adapters are not allowed for use on human beings or animals.•
Hazardous voltages will be produced when the outputs of several power adapters •
are connected in series (> 35 V/DC).
Do not cover the ventilation slots of power adapters. Such devices are cooled by •
convection in most cases.
Do not operate unattended power adapters and loads connected to them. •
Take measures apt to protect and secure the loads connected from the effects
produced by the power adapters (e.g. excess voltages, failure of the power
adapter) and the effects and hazards originating from the loads themselves (e.g.
inadmissibly high power input).
Power adapters may produce voltages exceeding 50 V/DC in a malfunction case. •
Suchvoltagescausehazards,evenifthespeciedoutputvoltagesofthedevices
are lower.
When working under a voltage only use tools which are explicitly allowed for the •
purpose.
Thecarsocketattheoutputofpoweradaptersmaynotbemodiedorrebuilt.•
Avoid installing bare metallic cables and contacts. Cover all bare points by •
suitable,difcultlyinammableinsulatingmaterialsortakeothermeasures,thus
protecting such points from being directly contacted. Likewise, take measures apt
to protect the electrically conducting elements of the loads connected from being
directly contacted.
If there is reason to believe that safe operation has become impossible put the •
power adapter out of operation and secure it against any unintended operation.
Safe operation must be presumed to be no longer possible, if
the unit exhibits visible damage -
the unit does not operate any longer -
the unit was stored under unfavourable conditions for a long period of time or -
the unit was exposed to extraordinary stress caused by transport. -
This product is not authorised for use in damp rooms or outdoors or under •
adverse ambient conditions. Adverse ambient conditions are:
Moisture or excessively high humidity of air -
Dustandinammablegases,vapoursorsolvents -
Heavy vibrations. -
In commercial and industrial facilities, the regulations for the prevention of •
accidents as laid down by the professional trade association for electrical
equipment and devices need to be observed.
Measuring devices used at schools, training facilities, do-it-yourself and hobby •
workshops should not be handled unless supervised by trained, responsible
personnel.
Never turn on the device immediately after it has been brought from a cold into a •
warm room. Condensation water that forms might destroy your device. Leave the
device switched off and wait until it has reached room temperature.
Miscellaneousb)
Consult an expert when in doubt about operation, safety or connection of the •
device.
Maintenance,modicationsandrepairsaretobeperformedexclusivelybyan•
expertorataqualiedshop.
If you are not sure about the correct connection or use, or if questions arise which are not
covered by these operating instructions, please do not hesitate to contact our technical
supportoranotherqualiedspecialist.
Voltcraft®, Lindenweg 15, D-92242 Hirschau, Tel. +49 180/586 582 7.
OPERATING ELEMENTS
A B
DC
2
1
Locking lever1.
Adapter slot2.
Power plug adapter
A. USA / Japan
B. Europe (except CH and UK)
C. United Kingdom
D. Australia
OPERATION
The surface of the casing will heat up intensely during prolonged operation
at a rated load. Attention: Danger of burns! Therefore, take great care to
sufciently ventilate the power adapter. Never operate it when partially or fully
covered. This will help avoid any damage.
When connecting a load always take care not to connect it as long as it is
switched on. A load in an ON condition, when being connected to the output
terminals of the power adapter, can cause sparks to form on the supply
terminals. This, in turn, can damage the supply jacks or the cables connected
and/or their terminals.
If you do not need the plug-in power adapter disconnect it from the mains.
Select one of the four power plug adapters included and insert it into the adapter slot on the 1.
underside of the power adapter, observing the correct direction. Slide the adapter towards
the locking lever until you hear the adapter lock into place.
To remove the adapter, use a tool (e.g. a screwdriver or tip of a pen) to press down the 2.
locking lever. Then slide the adapter away from the locking lever and remove the adapter.
Connect the power adapter to a standard mains socket.3.
The red LED on the top of the power adapter lights up and indicates that the power adapter 4.
is ready for use.
Connect the car socket to the consumer load and only then switch the consumer on.5.
Turn the consumer off before disconnecting it from the power adapter.6.
CLEANING AND MAINTENANCE
Do not use carbon-containing cleaning agents, petrol, alcohols or similar
agents. This can attack the surface of the device. Furthermore, the fumes are
a health hazard and explosive. Moreover, you should not use sharp-edged
tools, screw-drivers or metal brushes or similar objects for cleaning.
Disconnect the device from the mains voltage and from the connected consumer load •
before starting to clean the device.
The power adapter does not require any maintenance except that the surface of its casing •
needs cleaning occasionally. However, check the mains plug for the integrity of its insulation
at certain intervals.
Donotopenthedeviceormakeunauthorizedmodicationstothecircuitsinsidethedevice•
because this will invalidate the guarantee claim.
Useaclean,non-uffy,antistatic,anddryclothtoclearthedeviceofimpurities.•
TROUBLESHOOTING
Fault Possible cause
The connected load does not
function.
Does the red indicator on the power adapter light up?
Check the AC voltage (possibly AC fuse).
Is the power adapter overloaded?
Check the technical data for the load.
DISPOSAL
Electronic devices are recyclable waste and must not be disposed of in the
household waste!
At the end of its service life, dispose of the product according to the relevant
statutory regulations.
TECHNICAL DATA
Operating voltage ................. 100 – 240 V/AC, 50/60 Hz
Output voltage ...................... 12 V/DC
Output current ....................... max. 1000 mA
Output power ........................ max. 12 W
Operating temperature ......... 0 to +35 ºC, 20 – 85 % RH
Storage temperature ............. -20 to +50 ºC, 10 – 90 % RH
Cable length ......................... 1.8 m
Dimensions (W x H x D) ....... 43 x 66 x 78 mm
Weight .................................. 175 g
Legal notice
These operating instructions are a publication by Voltcraft®, Lindenweg 15, D-92242 Hirschau/Germany, Phone +49 180/586 582 7
(www.voltcraft.de).
Allrightsincludingtranslationreserved.Reproductionbyanymethod,e.g.photocopy,microlming,orthecaptureinelectronicdataprocessing
systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2011 by Voltcraft®
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
VOLTCRAFT 51 42 02 Operating Instructions Manual
- Type
- Operating Instructions Manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: VOLTCRAFT 51 42 02
- Deutsch: VOLTCRAFT 51 42 02
- Nederlands: VOLTCRAFT 51 42 02
Related papers
-
VOLTCRAFT SPS-1000 Operating instructions
-
-
-
-
-
-
-
-
-
