Beurer IPL 8500 Instructions For Use Manual

Brand: Beurer

Model: IPL 8500

Category: Skin care appliances

Type: Instructions For Use Manual

EN IPL 8500

Instructions for use ...............................3

Electromagnetic Compatibility

Information .................................................26

IPL 8500

READ THIS MANUAL COMPLETELY AND CAREFULLY BEFORE USING THIS PRODUCT

Keep this manual in a safe location for future reference

1. What is IPL 8500

Indications for use

The IPL 8500 device is an over-the-counter device intend-

ed for the reduction of unwanted body and/or facial hair.

IPL 8500 is also intended for permanent reduction in hair

regrowth, defined as a long-term, stable reduction in hair

regrow when measured at 6, 9, and 12 months after the

completion of treatment regimen.

IPL 8500 is a personal use device intended for the reduc-

tion of unwanted hair.

ENGLISH

Table of Contents

What is IPL 8500.............................................................. 3

2. Who should use the IPL 8500 and

how to decide to use IPL8500 ....................................... 4

3. Benefits ........................................................................... 5

4. Who should NOT use the IPL 8500? ............................... 6

Who cannot use the IPL8500 - CONTRAINDICATIONS . 6

What you must do to avoid serious harm – WARNINGS 7

What you must do to avoid other harm – CAUTIONS .... 8

5. Possible Adverse Reactions ............................................ 9

6. IPL 8500 Description ..................................................... 11

Device Components ..................................................... 11

User interface description ............................................. 12

7. User Instructions ........................................................... 14

Preliminary Test ............................................................ 14

Step 1: Device Set-Up .................................................. 15

Step 2: Prepare your skin ............................................ 15

Step 3: Device operation ............................................. 16

Recommended treatment protocol: ............................ 18

What to expect when using IPL 8500 ......................... 19

Step 4: Cleaning & Storage ......................................... 20

8. Post treatment care ..................................................... 20

9. Troubleshooting ........................................................... 20

10. Warranty / service ........................................................ 21

11. Device specification parameters ................................. 22

12. Labeling ....................................................................... 23

13. Electromagnetic compatibility (EMC) and

Specifications ............................................................. 24

14. Treatment Log.............................................................. 25

IPL 8500 features the proprietary RPL™ technology (Re-

active Pulsed Light).

IPL 8500 is intended for home use environment.

RPL (Reactive Pulsed Light)™ technology

- How does it work

The IPL 8500 is based on the scientific principle of select-

ive photothermolysis.

RPL™ (Reactive Pulsed Light) advanced technology uses

IPL (Intense Pulsed Light) technology along with a combina-

tion of unique skin condition sensors. The light penetrates

the epidermis to the dermis and is absorbed by the melanin

in the hair shaft. The heat generated by the absorbed light

then dissipates into the follicle and generates local thermal

damage, causing a reduction in hair growth.

Long-term hair reduction – Hair growth

cycle

Two factors play an important role in optimal long-term hair

reduction:

• Hair growth cycle involves three phases: Anagen, Cata-

gen, and Telogen. Anagen is the growth phase, while

Catagen and Telogen are the resting phases. Permanent

hair reduction can only occur during the Anagen phase.

• Skin types (according to the Fitzpatrick scale) are illus-

trated on the diagram below: Darker skin contains more

melanin, which competes with the targeted hair for

energy light absorption. When more light energy is ab-

sorbed into the skin, there is a greater risk of adverse

effects, and the epidermis may be damaged.

Please make sure to carefully read this user guide

before you start treating with IPL 8500.

2. Who should use the IPL 8500

and how to decide to use

IPL8500

• IPL 8500 is intended for women and men who desire to

reduce unwanted hair.

•

IPL 8500 is intended for use on entire body (e.g. legs,

arms, underarms, bikini line, back, shoulders and chest)

and allowed facial areas (e.g. above upper lip, cheek,

jaw, chin and neck).

•

IPL 8500 is intended for use on skin tone type I to IV ac-

cording to Fitzpatrick skin chart below.

I II III IV V

The use of IPL 8500 on naturally dark skin is forbidden.

IPL 8500 works best on dark hair or hair that contains more

melanin. Brown and light brown hair will respond, but typ-

ically will require more treatment sessions. Red hair may

show some response. White, grey or blond hair shows a

more limited response. Nevertheless, some users have

noted hair reduction after multiple treatment sessions.

Never use IPL 8500 around or near your eyes.

Note: IPL 8500 is especially designed for your own per-

sonal treatment! It is intended for a single user only.

3. Benefits

Safety! With IPL 8500, your skin is in good hands.

IPL 8500 is based on RPL technology, including an auto-

matic built-in skin color sensor that is designed to provide

you with complete safety and reassurance. The sensor con-

tinually evaluates your skin tone and allows IPL 8500 to

perform only on suitable areas. This smart safety feature

automatically disables treatment if your skin is too dark or

too tanned. As an extra precaution, the IPL 8500 has been

designed to only emit a light pulse when it is in contact with

your skin.

Convenience! The IPL 8500 can be operated in two treat-

ment modes:

•

Pulse mode: ideal for initial device usage or for small or

curvy areas such as the knees, underarms and bikini line.

Each press on the trigger button will release a pulse to

the treatment area (the trigger button may be hold con-

tinuously or pressed repeatedly).

• Trigger-less mode: perfect for large areas, such as the

back and legs. After holding the trigger button until three

consecutive pulses are released, or by pressing the “trig-

ger-less mode” button ( ) the device will automatic-

ally enter trigger-less mode. In this mode consecutive

pulses will be released without the need to press the

trigger button.

Chargeable! The IPL 8500 has a rechargeable battery. After

charging your device, you can use it as cordless and enjoy

a more flexible and convenient treatment.

Versatility! The IPL 8500 includes an additional precise

treatment area window, especially designed for more ef-

fective usage, allowing more precise treatments at differ-

ent body areas.

Effective! For permanent reduction in hair regrowth, defined

as a long-term, stable reduction in hair regrow when meas-

ured at 6, 9, and 12 months you should follow treatment

regimen. With the clinically proven IPL technology you may

see some improvement already in 3-4 weeks, when using

the device according to the recommended treatment proto-

col described in this User Guide (see page 28).

The hair will continue to grow up to two weeks after a hair

reduction session. However, thereafter as the hair grows in

three different stages it will naturally and gradually fall out,

depending on the hair growth stage in during which the

treatment was done (only hairs in the active growth phase

will be affected). Some hair may not be affected by the IPL

8500 because of the different hair growth phases.

Response to IPL 8500 hair reduction differs between indi-

viduals depending on biological factors and how closely

treatment instructions are followed.

Note: Hair removal by lasers or intense pulse light sources

can cause increased hair growth in some individuals. Based

upon currently available data, the highest risk groups for

this response are females of Mediterranean, Middle East-

ern, and South Asian heritage treated on the face and neck.

4. Who should NOT use the IPL

8500?

IPL 8500 is designed especially for you, to be used over

normal, healthy and intact skin, for both safe and eect-

ive treatment. However, IPL 8500 is not appropriate for

everyone. Please read the information below before use. If

you still have any doubts, and you are unsure that the IPL

8500 is safe for your use, please consult with your per-

sonal physician.

Who cannot use the IPL8500 -

CONTRAINDICATIONS

Do NOT use IPL 8500 device if you have any of the fol-

lowing conditions:

• If you have an active implant such as a pacemaker, in-

sulin pumps, or similar devices since it may cause inter-

ference.

•

If you are pregnant or with a slight chance of being preg-

nant or nursing since it has not been established and

may result in stimulation of pigmentation.

•

If you have skin cancer or on areas at risk of malignancy

or if you have received radiation therapy or chemother-

apy within the past 3 months since it has not been es-

tablished and the immune system can be compromised

which can lead to serious injury.

• If you suffer from epilepsy, it could trigger seizure.

•

If you have damaged or broken skin or history of Herpes

or Psoriasis outbreak in the treatment area since it can

result serious side effects.

•

If you suffer from keloid scar (growth of extra scar tis-

sue where the skin has healed after an injury) formation

in the treatment area since it has not been established

and may result serious skin complications.

•

If you have been taking Tetracycline antibiotics and medi-

cation with the following active ingredients within the last

two weeks: Retinoid acid, Retina-A, Vitamin A such as

Accutane as it is considered to be a photo-sensitive drug

and may result serious skin injury.

• If you are photosensitive or have other diseases related

to light sensitivity as it may lead to serious injury.

•

If you suffer from severe or decompensated metabol-

ic conditions, such as diabetes, since it may cause a

greater risk of delayed healing and infection in the case

of an adverse effect.

•

If you have had a skin peel or other skin resurfacing pro-

cedure within the last 8 weeks in the treatment area as it

may result in stimulation of pigmentation.

Note: If you have undergone any other aesthetic procedures

or any uncertainty regarding potential side effects, consult

your physician before using the IPL 8500.

What you must do to avoid serious harm –

WARNINGS

•

Do not use IPL 8500 on naturally dark skin (see guidance

at the back cover and high Fitzpatrick level in the “Who

should use the IPL 8500 section”).

•

Do not use the IPL 8500 if you have dark brown or black

spots such as freckles, birth marks, around the nipples,

moles or blisters on the area to be treated.

• Do not use the IPL 8500 on mucous membranes such

as nostrils, lips of the mouth, eyelids, ears, genital area

and the anus as it may lead to serious injury.

•

Do not use the IPL 8500 over piercing or any metal items

such as earrings or jewelry on the area to be treated as

it may cause burns.

•

Do not use the IPL 8500 over areas with tattoos or

permanent makeup on the area to be treated.

•

Never look directly at the light coming from the IPL 8500

applicator and lamp as it may cause eye injury.

• Never use flammable liquids such as alcohol (including

perfumes, sanitizers, or other applications containing al-

cohol) or acetone to clean the skin one hour before using

IPL 8500 as it may cause burning of the skin.

• Do not use IPL 8500 on tanned skin or after sun ex-

posure as this can cause serious burns or skin injury.

Avoid more than 15 minutes of sun exposure for 4

weeks before your treatment and for at least 2 weeks

post treatment. If during this period your treated skin

area is exposed to sunlight, make sure to apply SPF

30 or higher sunscreens.

• Do not treat the same area of skin more than once

per treatment as it may cause skin irritation.

What you must do to avoid other harm –

CAUTIONS

• KEEP OUT OF CHILDREN’S REACH.

• This appliance is not intended for use by persons with

reduced physical, sensory or mental capabilities.

•

Do not use this appliance near bathtubs, showers or

other vessels containing water as it may lead to elec-

trocution risk.

• Do not open or repair the device as it may expose you

to dangerous electrical components which may cause

serious bodily damage.

• Do not leave the device unattended while plugged into

the electricity as it may lead to electrocution risk.

• Do not use the device if any part of the device or its ac-

cessories are not working properly, appear damaged,

broken, loose, missing, wet or if you see or smell smoke.

•

Before using IPL 8500, make sure the device is clean,

dry and intact. Cleaning instructions are detailed in the

“Cleaning” chapter.

•

Do not share device at any time, due to the possibility of

transmitting diseases between users.

•

Use IPL 8500 only with the supplied external

power and accessories. For your safety, never use

DC adapters which are not approved by the manu-

facturer.

• Use the IPL 8500 device only according to the instruc-

tion for use and the intended aesthetic use.

5. Possible Adverse Reactions

When using IPL 8500 device according to the instructions

for use, adverse reactions are rare. However, every aesthetic

procedure, including the usage of home-use devices, may

cause some degree of adverse reactions (as listed in the

table below). The possible adverse reactions are temporary,

rare, and resolve spontaneously within few hours or days.

In case adverse reactions appear, stop using the IPL 8500

device.

Please consult your physician if necessary.

Degree of Side Effects Side Effects

Minor

Side-Effects

Skin Irritation

Skin Redness

Skin Sensitivity

Rare

Side-Effects

Skin Burns

Scarring

Pigment Changes

Excessive Redness

and Swelling

Extremely Rare Side-Effects Infection

Bruising

For your convenience, additional explana-

tions are given below.

Skin Irritation

• The use of Pulsed Light Hair Removal System is gener-

ally very well-tolerated, the majority of users do feel a

sensation of warmth and a mild stinging sensation dur-

ing treatment or a few minutes after. Anything beyond

this skin irritation – discomfort is abnormal and means

that either the energy level is too high, or you shouldn’t

continue using the IPL 8500 as you are unable to toler-

ate the hair reduction application.

Skin Redness

•

Redness on the treated area may appear right after using

the application or within 24 hours of using the IPL 8500.

Consult your physician in case the redness does not dis-

appear within 2 to 3 days.

Skin Sensitivity

• You may feel that your skin in the treated area is more

sensitive so you may encounter dryness or flaking of

the skin.

Skin Burns

•

Rarely, burns on the treated area can occur following the

use of the hair removal system. The burns can require

a few weeks to heal and, extremely rarely, may leave a

visible permanent scar.

Scarring

•

In rare cases, permanent scarring may occur. Usually

when scarring occurs it is in the form of a flat and white

lesion on the skin (hypotrophic). However, it can be large

and red (hypertrophic) or large and extend beyond the

margins of the injury itself (keloid). Subsequent aesthet-

ic treatments may be required to improve the appear-

ance of the scar.

Pigment Changes

•

Use of the IPL 8500 may cause temporary skin hyper-

pigmentation (increased pigment or brown discoloration)

or hypopigmentation (whitening) to the surrounding skin.

The risk is higher for people with darker skin tones. Usu-

ally discoloration or changes to skin pigment are tempor-

ary and permanent hyperpigmentation or hypopigmen-

tation rarely occur.

Excessive Redness and Swelling

• Very rarely, the treated area skin may become very red

and swollen. This side effect is very common in sensi-

tive areas of the body. The redness and swelling should

be decreased after 2 to 7 days and you should treat the

area by applying ice. You should avoid exposure to sun.

Infection

• In rare cases, infection of the skin is a possible risk fol-

lowing a skin burns caused by the application.

Bruising

•

Blue-purple bruising is exceedingly rare by using the IPL

8500 and can last 5 to 10 days. As the bruising fades,

there may be a rust-brown discoloration of the skin

(hyperpigmentation) that can be permanent.

6. IPL 8500 Description

Device Components

The IPL 8500 device set consists of the following compon-

ents, as demonstrated in the picture below:

• Hand-held device

• External power supply

• Precise and Large Treatment windows

1. Status indicator:

Lack of contact

Non-allowed skin tone

Error mode

2. Internal lamp

3. Treatment window

4. Skin tone and contact window (Fitzpatrick window)

5. Trigger button

6. 1-6 energy level lights

7. Battery status indicator

8. Increase energy level button

9. Decrease energy level button

10. Trigger less mode button

11. ON/OFF button

12. Power supply socket

Large treatment

window

Precise treat-

ment window

Power adapter

User interface description

The user interface and control capabilities include the fol-

lowing features:

1. ON/OFF button – The button activates and deacti-

vates your device by a single press. In addition, when

the device is left unattended for 5 minutes, the device

will automatically turn off. When turning on the device,

all energy levels lights will light up for a split second, and

then the device will turn on at energy level 1.

2. Trigger-less mode button – A press on the button

will activate the trigger-less mode (‘glide mode’). In this

mode, consecutive pulses will be released without the

need to press the trigger button, as long as the device is

in full contact with the skin and applied on allowed skin

tone. The glide mode can be turned off by additional

press on the trigger-less button or will be automatically

turned off if the device is unused (or doesn’t have proper

skin contact and skin tone detected) for a few seconds.

3. Energy selection buttons – The + (Increase energy

level) and – (Decrease energy level) buttons, al-

lows energy level selection between 6 different lev-

els. Choose the energy level according to your com-

fort and as selected in the preliminary use test.

a. Pressing the + or - buttons (after the device turns

on) will increase or decrease the energy by a single

level. Each additional press will change the energy

level, between the lowest level (indicated as “1”) to

the highest (indicated as “6”).

Note that when you reach the maximal energy level

(“6”), pressing the + button again won’t change the

energy level. Similarly, when you reach the min

imal energy level (“1”), pressing the – button won’t

change the energy level.

b. The 1-6 energy level lights will light up Green ac-

cording to the selected energy level (e.g. at energy

level 1, one green light will be lit, at energy level 2,

two green lights will be lit).

4. Battery status indicator - The indicator, marked as ,

shows the status of the battery charging:

a. Red – battery is being charged.

Note: if in addition to this red light, energy level “1”

is green, the device is turned on.

b. Green - Battery is fully charged and the device is

connected to the external power supply.

c. ‘slow’ blinking red – low battery level (about 30%

of battery is charged).

d. ‘fast’ blinking red – low level of battery (about 10%

of fully charged).

Note: the green or blinking red battery status indi-

cators will appear only while the device is turned

on.

5. Large Treatment window and Precise Treatment win-

dow – for most comfortable treatment, select the ap-

propriate treatment window per different body areas:

a. Large Treatment window (the optical filter is built-

in the device) – use the IPL 8500 with the large treat-

ment window for treatment of large body areas, such

as legs, back and arms. Using this large window will

make hair removal faster and easier.

b. Precise Treatment window (additional snap-on win-

dow with red optical filter) – attach (just snap-on) the

Precise Treatment window for treatment of small and

delicate areas, such as face (below cheek line area)

and bikini line.

6. Status indicator light – this indicator (located at the back

side of the device) has several statuses, as detailed in

the table below:

Indicator Mode

“Steady”

green light

A pulse is ready. While

pulse is delivered or be-

tween pulses, no light ap-

pears.

“Momentary”

orange light

Activation

(pulse) is

blocked

The device does not deliv-

er a pulse due to the lack

of full skin contact.

“Momentary”

Red light

Activation

(pulse) is

blocked

The device does not de-

liver a pulse due to non-al-

lowed skin tone (high Fitz-

patrick level as described

at the back cover of the

User Guide).

“Blinking”

orange light

Close to

end of life

Indicates about the close

end of the lamp life time.

“Steady”

red light

End of life/

blocked

Device is permanent-

ly blocked, the lamp has

reached its maximum flash

limit or internal malfunc-

tion has been occurred or

the treatment area window

is not properly attached to

the device.

7. User Instructions

IPL 8500 is an optimal solution for all body areas such as

your underarms, bikini line, arms, back, shoulders, chest,

legs and allowed facial areas such as above upper lip,

cheek, jaw, chin and neck.

Preliminary Test

The preliminary test is intended to determine your skin’s re-

action to the IPL 8500 treatment and help you set the opti-

mal energy level for each treatment area.

Do a preliminary test on each area you intend to treat 48

hours prior to the first full treatment.

Note: Do not treat full areas with energy levels that you

have not tested before!

Do not treat the tested area for at least 48 hours after the

preliminary test is done.

1. Set up the device as indicated in the “Step 1: Device set

up” section and prepare your skin (as described in “Step

2: Prepare your skin”).

2. Select the lowest energy level and deliver a pulse on the

selected preliminary test skin area.

3. If you feel comfortable with the energy level, increase it to

level 2 and perform an additional pulse on the next spot.

4. Only if you feel comfortable, you may reach the maximum

energy level (6th).

5. Stop the test once you do not feel comfortable, as in-

creasing the energy level increases the risk of adverse

effects.

6. If you see adverse effects such as severe redness or blis-

tering - stop the test immediately.

7. Wait 48 hours and examine the tested area.

• If the skin in the test area seems normal (no response

or mild redness observed), you can proceed with a

full treatment in the highest comfortable energy level

that you tested.

•

If you see extreme redness, swelling, or blistering even

in the low-energy level settings, do not proceed to the

full treatment in that area.

Step 1: Device Set-Up

1. Remove all components from the box (handheld device,

desired treatment window and power supply).

2. Make sure the device is clean, dry, and intact.

3. Select the desired treatment window and simply snap it

onto the light exit window.

Note: the device will not operate without the treatment win-

dow or if the treatment window is not properly attached.

4. Charge your IPL 8500 device, as necessary.

•

Before your first use and when the battery is empty,

fully charge the IPL 8500 battery (full charging of the

battery takes up to 2.5 hours).

•

Whenever battery level is low, as indicated by the blink-

ing red light at the Battery status indicator, recharge

your device.

• Fully charge the appliance every 3 to 4 months, even

if you did not use the appliance.

•

For charging your device, insert the power cord into

the socket and the power supply into the wall socket.

When the battery is fully charged, the charging light

lights up green continuously.

•

After charging, remove the power adapter from the wall

socket and disconnect it from your device.

Notes:

• Some warming of the device and power adaptor during

charging is normal.

• Charging should be done in a room temperature or cool

environment, never above 104°F (40°C). The device is

equipped with battery-overheat protection and will not

charge if the room temperature exceeds 104°F (40°C).

• Never cover the appliance and the adapter during char-

ging.

•

You can use the device while it is being charged.

This may allow you limited number of pulses since

battery charging is slower then battery consump-

tion during use.

The IPL 8500 is now ready to be used.

Step 2: Prepare your skin

1. Remove all jewelries from treatment area.

2. Make sure your skin at the treatment area is shaved or

trimmed and cleaned from any residue such as pow-

ders, creams, makeup, antiperspirants or deodorants.

3. Between treatments, you can shave but don’t wax or

pluck hair.

4. Never use flammable liquids such as alcohol (including

perfumes, sanitizers, or other applications containing al-

cohol) or acetone to clean the skin one hour before using

the device as it may cause burning of the skin.

5. Do a preliminary test on a small patch of skin in the in-

tended treatment area, 48 hours prior to first use of the

IPL 8500 to determine energy level settings for your treat-

ment (as depicted in the preliminary test section).

Important: Do not use any cream or gel while using the

device since it may dirt your device and prevent its nor-

mal operation.

Remember: The IPL 8500 comes with a built-in skin-tone

sensor, enabling the application only on a suitable skin tone.

This unique safety feature will not let you treat areas where

your skin is too dark or too tanned, even if your general

skin type is lighter.

Step 3: Device operation

Note: A preliminary test should be conducted before pro-

ceeding to a full treatment. See “preliminary test” section

above.

1. Prepare your skin (see step 2).

2. To turn the IPL 8500 device on, press the ON/OFF but-

ton ( ). Energy level 1 green indicator will light on. The

device sets itself on the lowest energy level—level 1. For

other energy levels press the increase energy level but-

ton (+) or decrease energy level button (-).

3. You may decrease or increase the energy level accord-

ing to your convenience (to reach the level determined

in the preliminary test section). The energy level indica-

tor lights will light up green according to the selected

energy level, one green light for energy level 1, two lights

for energy level 2, etc.

4. Place the IPL 8500 treatment window on the desired body

area with full contact with the skin.

•

If IPL 8500 is not properly applied, the status indicator

will be “momentary” orange.

•

If your skin tone is too dark/ tanned, the status indicator

will be “momentary” red. In these cases, the IPL 8500

will not trigger a pulse in that area of skin.

5. Press the device window gently against your skin to be

treated to ensure proper contact and use the trigger but-

ton to release a pulse (make sure all treatment window

is in contact with the skin). Start moving the device with

each pulse to the next spot, while the device is detached

or not with your skin, according to your comfort. When

the pulse will be released, you will see a bright flash, you

will hear a popping noise, and you may feel a mild sting-

ing and/or heat sensation. After each pulse, the device

will immediately recharge and will be ready for the next

pulse. You may choose from 2 treatment modes, either

the ‘pulse mode’ or the ‘trigger-less mode’:

a. Pulse mode: Press the trigger button once for release

of a pulse to the treatment area. After moving to the

next spot to be treated, press the trigger button again

to release another pulse. The trigger button may be

either pressed or continuously held.

b. Trigger-less mode (glide mode): Begin treatment

in the ‘pulse mode’. After three consecutive pulses

without releasing the trigger button are released, or

after pressing the trigger-less button, the device will

automatically enter into the trigger-less mode and al-

low continuous consecutive pulses release without

the need to press or hold the trigger button. In trig-

ger-less mode, the device will automatically deliver

a pulse (without holding the trigger button) when a

pulse is ready (1-3 seconds after the previous pulse)

and when proper skin tone and contact are detected

by the skin tone and contact sensor. If activated by

the trigger-less button, the glide mode can be turned

off by additional press on the button or will be auto-

matically turned off if the device is unused (or doesn’t

have proper skin contact and skin tone detected) for

a few seconds. If activated by constant press on the

trigger button, the glide mode will be automatically

deactivated when the device is not in proper contact

with the skin or when skin is too dark/ tanned.

6. After the treatment, turn off the device by pressing the

“ON/OFF” button; an orange indicator will light up while

the device is in the shutdown mode.

7. Perform treatment sessions according to the “Recom-

mended treatment protocol” section.

Important notes:

• Try not to overlap pulses on the same spot of skin. Re-

peated pulses on the same spot may cause burns.

• Do not treat the same area of skin more than once per

treatment as it may cause skin irritation.

• IPL 8500 will not trigger a pulse if:

a. There is no full contact of the treatment window with

the skin

b. Your skin tone is too dark or tanned

Recommended treatment protocol:

Treatment areas depending on hair color and their treatment protocol:

Hair Color

Fitzpatrick Skin

Level

Energy Levels

Treatment Area

Average Number

of Treatments

Treatment Interval

Light Brown to

Brown

I–IV (Inclusive) 1–6 Legs 10–12

The 1–4 treatments

will be approximately

two weeks apart, fol-

lowed by four-week

time intervals.

Arms

Underarms

Bikini Lines

Brown to Black

I–IV (Inclusive) 1–6 Legs 8–10

Arms

Underarms

Bikini Lines

Important: Facial treatment should be performed at 1-4

energy levels only.

Don’t forget to select the proper treatment window

(either the large Treatment Window or the additional

small Precise Treatment window), according to the size

of the treatment area and your comfort.

Plan your IPL 8500 treatment

Energy level should primarily be chosen based on your own

comfort.

The energy levels vary from level 1 to level 6 with a light flu-

ence of 2-5 [J/cm

Each treatment pulse should be applied on different skin

spot with no repetition or overlap. The entire treatment area

(underarms, bikini line, arms, back, shoulders, chest, legs

and allowed facial areas) will be determined by the user.

Notes:

•

Response to IPL 8500 hair reduction differs between in-

dividuals, depending on their unique biological factors.

•

It may take up to 3-4 weeks before results of the IPL

8500 treatment can be seen. The hair will continue to

grow up to two weeks after a hair reduction session.

However, thereafter as the hair grows in three different

stages the hairs will naturally and gradually fall out de-

pending on the hair growth stage in during which the

treatment was done (only hairs in the active growth

phase will be affected). Some hair may not be affect-

ed by the IPL 8500 because of the different hair growth

phases. To remove this hair multiple treatment sessions

are required to reach the desired result.

•

The number of sessions required for achieving long term

results is different for every treatment area and changing

for every user, as it is affected by type of skin, hair and

hormonal changes.

•

Red hair may show some response. White, grey or blond

hair shows a more limited response. Nevertheless, some

users have noted hair reduction after multiple treatment

sessions.

• IPL 8500 is suitable for men. However male body hair,

especially those on the chest will require more hair re-

duction sessions.

• Maintenance will be needed from time to time if growth

is still visible.

•

You may use the treatment log at the end of this manual,

in order to assist you with recording your specific treat-

ments areas, dates and duration.

What to expect when using IPL 8500

During your hair removal treatment it is normal to experi-

ence:

• A flash of light on each press of the trigger button. The

light will not harm the eyes.

• A pop noise with each pulse – occurs whenever a pulse

is activated.

• A sensation of warmth – radiates from the light energy

after each pulse.

• A mild stinging sensation – can be felt, similar to being

snapped with a rubber band.

Some mild red or pink color may appear during or just

after using the IPL 8500.

Step 4: Cleaning & Storage

1. Make sure to turn off and unplug unit before cleaning.

2. It is recommended that the treatment window area will be

cleaned after every session by using a dry, clean cloth

to gently wipe the device.

3. Keep the device dry. Never place, store or use IPL 8500

near bathtubs, showers, basins or other vessels con-

taining water as this may cause severe electrocution.

4. If you do not plan on using your IPL 8500 for a long period

of time, it is recommended to keep it clean and stored.

5. If you plan to travel and take your IPL 8500 with you, you

should store it in the original box and follow this section.

8. Post treatment care

• Apply a calming lotion such as Aloe Vera.

•

Avoid using peeling and bleaching creams or similar

products for at least 24 hours, as this irritates the treat-

ed skin.

•

Avoid direct sun exposure for at least 2 weeks post treat-

ment. If recently treated skin is exposed to sunlight in

this time period, make sure to apply SPF 30 or higher

sunscreen.

•

Do not wax or pluck hairs from treated areas between

treatment sessions.

9. Troubleshooting

•

If you experience any problems with the IPL 8500, please

refer to below information to try to resolve it.

• If the IPL 8500 does not turn on, make sure that the de-

vice is charged (as indicated by the green light at the

battery status indicator).

• If IPL 8500 does not trigger a pulse:

a. the treatment window is properly attached to your de-

vice (the device will not be operable if the treatment

window is not attached or not properly attached to

the device.

b. the device did not automatically exit trigger-less mode

after proper contact and skin tone were not detected.

c. there is full contact with the skin. The trigger button

will activate a flash pulse only when the device is in

full contact with the skin.

d. the area you are trying to treat is not too small, curved

or bony to treat. You should get the whole treatment

window to touch the treatment area (try to pull the

skin flat).

e. if the skin color level identified by IPL 8500 is too dark,

the flash activation will be blocked. This situation is

indicated by a “momentary” red light on the device.

Page is loading ...

Beurer IPL 8500 Instructions For Use Manual

Brand: Beurer

Model: IPL 8500

Category: Skin care appliances

Type: Instructions For Use Manual

Download PDF

report

Beurer IPL 8500 Instructions For Use Manual

Beurer IPL 8500 Instructions For Use Manual

Related papers

Other documents