GB
Programme
Care
Labels
Max.
Load
kg
Type of wash / Notes
- respect the manufacturer's recommendations on the care label
Detergents and Additives Special options Max
Spin Speed
rpm
Pre-
wash
Main
Wash
Softener Start
delay
Av
vio
ritardato
Pre-
wash
Pre-
lavaggio
Eco
Eco
Intensive
rinse
Risciacquo
intensivo
Rinse
hold
Anti
piega
Variable
spin
Centrifuga
variabile
Cotton
40 - 60 - 95 °C
Cotone
40 - 60 - 95 °C
7.0
Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc.
made of cotton and linen.
With heavily soiled laundry the additional “Prewash” option can be selected as well.
Yes
Max.
Synthetics
30 - 40 - 60 °C
Sintetici
30 - 40 - 60 °C
3.0
Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira),
polyamide (Perlon, Nylon) or blends with cotton.
Yes
1000
1)
Delicates
30 - 40 °C
Delicati
30 - 40°C
1.5 Curtains and delicate clothing, dresses, skirts, shirts and blouses.
Yes
– –
1000
1)
Daily load
40 °C 40 °C
4.0
Shortly worn outer clothing made of cotton, polyester, polyamide and blends with
cotton.
– Yes
– –
Max.
Quick wash
30 °C
Rapido
30 °C
4.0
Shortly worn outer clothing made of cotton, polyester, polyamide and blends with
cotton.
– Yes
– – –
Max.
Wool
Cold - 40 °C
Lana
Freddo - 40 °C
1.0
Only woollens with a felt-free finish, labelled with the woolmark and identified as
machine washable.
– Yes
– – –
1000
1)
Handwash
40 °C
Lavaggio a mano
40 °C
1.0 Textiles made of linen, silk, wool and viscose marked as “handwashable”. – Yes
– – –
400
1)
Lingerie
30 °C
Lingerie
30 °C
1.0
This cycle is particurarly suitable to treat delicate lingerie (use of laundry net
strongly recommended).
– Yes
– – –
400
1)
Rinse & Spin
Risciacquo &
Centrifuga
– 7.0 Same as the last rinse and the final spin in the “Cotton” programme. – –
– –
Max.
Spin Centrifuga
– 7.0
In this programme spinning is intensive. Same as the spin cycle in the “Cotton”
programme.
– – –
– – – –
Max.
Gentle Spin Centrifuga breve
–
1.0
In this programme spinning is gentle. Same as the spin cycle in the “Wool” programme. – – –
– – – –
1000
1)
Drain Scarico acqua
– –
Drain only - no spinning. Alternative method of terminating programme after “Rinse
hold”.
– – –
– – – – – –
A. “Door open” indication
This washing machine is equipped
with automatic safety functions which
detect and diagnose faults at an early
stage and react appropriately, e.g.:
B. “Service” indication
C. “Water tap closed” indication
D. “Clean pump” indication
E. Programme selector
F. “Start/Pause” button
G. Spin speed selector
H. Programme sequence indicator
and St
art delay indicators
I. “Reset” button
J. “Start delay” button
A
B
PROGRAMME CHART
I
F
E
H
C
D
J
G
5019 301 01146
Whirlpool is a registered trademark of Whirlpool USA.
: option / Yes : dosing required
1)
For improved garment care spin speed is restricted in these programmes.
5019 301 01146
CONSUMPTION DATA
Add detergents as indicated on the front page and as
described in the chapter “Detergent and Additives” in
your Instructions for Use.
Turn the
programme selector to the desired
programme and temperature. The “Start/Pause”
indication lamp blinks and the indication lamp of the
predefined spin speed lights up.
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR AND
SELECT THE PROGRAMME
RED INDICATIONS
“Service”
Lighting up of the “Service” indication can be caused
by a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your “Instructions for
Use”; if the fault persists, contact our After Sales
Service.
“Water tap closed”
The appliance has no or insufficient water supply.
Open the water tap: if the indications still lights
up, refer to the “Troubleshooting Guide” in the
Instructions for Use.
“Clean pump”
Waste
water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned:
in the latter case refer to the Instructions for Use
(“Removing the Filter”).
“Intensive rinse” button
• More water is added and rinse cycle is prologned.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
“Rinse hold” button
• The laundry remains in the last rinse water
w
ithout progressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and
“Delicates”.
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want to
drain only.
• If you select “Rinse Hold” do not leave items to
soak for too long
.
Note: The programme stops to “Rinse hold” at
the time the “Rinse hold” light in the programme
sequence indicator is on. The indication lamp next
to the
“Start/Pause” button bllinks.
Terminate the “Rinse hold” option:
• Press the “Start/Pause” button; the programme
will terminate automatically with the final spin
cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain”
programme
and press the “Start/Pause” button.
PROGRAMME END
• All the lights of the programme sequence indicator
are off, and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start/Pause” button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the “Start/Pause” button again.
The new programme continues at the same
position where the previous programme was
interrupted. Do not add detergent for this
programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme before
the end.
• Press the “Reset” button for at least 3 seconds.
Any existing water is drained out before the door
can be opened.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the
respective indication lamp lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch
off automatically. Unsuitable combinations of options
are deselected automatically.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approxima
tely 15 min.
• Do not use liquid detergent for the main wash
when activating the Prewash option
.
“Eco” button
• With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
“Variable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during the rinse. The water is drained out only.
START DELAY
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)
Cotton 95 7.0 74 * 2.10 2:10
Cotton 60 7.0 69 1.33 2:10
Cotton with “Eco” ** 60 7.0 54 1.19 2:20
Cotton 40 7.0 69 0.75 2:15
Synthetics 60 3.0 50 * 0.80 1:35
Synthetics 40 3.0 45 0.50 1:20
Delicates 30 1.5 60 0.50 0:45
Daily load 40 4.0 45 0.50 1:00
Quick wash 30 4.0 45 0.40 0:30
Wool
40 1.0 60 0.50 0:45
Handwash 40 1.0 45 0.50 0:40
Lingerie 30 1.0 45 0.40 0:36
Whirlpool is a registered trademark of Whirlpool USA.
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the
lamp lights to show the the door can be opened.
As long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel (Reset)
a running programme before the end”.
PROGRAMME START
Open the tap and press the “Start/Pause” button.
The indication lamp next to the “Start/Pause”
button lights up. The programme sequence indicator
shows the current programme phase, running from
left to right through Wash, Rinse, Spin/Drain.
When the programme phrase is finised, the
corresponding indication goes out.
The “Start delay” allows to run the machine at the
consumer's convenience, for example at night when
electricity is cheaper. Do not use liquid detergent
when activating th Start Delay.
• Select programme, temperature and options.
• Press the “Start delay” button to select the delay
time by 1, 3, 6, 9 or 12 hours.
• Press the “Start/Pause” button.
The indication over the “Start delay” button
fleshes and goes off when the programme starts.
• Once having pressed the “Start/Pause” button,
the countdown of the time delay begins. When the
programme starts, the start delay indicator light
goes off and is replaced by the programme
sequence indication.
• After the “Start/Pause” button has been pressed,
the number of hours preselected can be reduced
by pressing again the “Start delay” button.
To cancel the “Start delay”
..before you press the “Start/Pause” button:
• Turn the programme selector to another position
or press the “Reset”
button.
..after having pressed the “Start/Pause” button:
• Press the “Reset” button for at least 3 second - the
start delay indicator light goes out.
/
