Australian Barbell Company 20 Class Bar Rack Assembly Instructions

Brand
Australian Barbell Company
Model
20 Class Bar Rack
Type
Assembly Instructions

Australian Barbell Company 20 Class Bar Rack is a sturdy and versatile storage solution for barbells and weight plates. It can accommodate up to 30 barbells and has three columns of plate storage, making it ideal for gyms, fitness centers, and home gyms. The rack is easy to assemble and comes with special plastic bolt-head covers to protect the bolts and nuts from damage.

Australian Barbell Company 20 Class Bar Rack is a sturdy and versatile storage solution for barbells and weight plates. It can accommodate up to 30 barbells and has three columns of plate storage, making it ideal for gyms, fitness centers, and home gyms. The rack is easy to assemble and comes with special plastic bolt-head covers to protect the bolts and nuts from damage.

Australian Barbell Company
54 Bond St West, Mordialloc, VIC 3195
ABN 29 004 420 848
P 03 9580 5945
F 03 9580 7123
[email protected]
www.australianbarbellco.com
20/30 CLASS BAR RACK
ASSEMBLY INSTRUCTIONS
Step 1: Arrange Racking as shown below. Note, pictures below are of the
20 bar rack. The 30 bar rack has three columns of plate storage.
Step 2: Loosely bolt into position ensuring;
i) 45mm End Washers are used at each position listed below.
ii) A flanged washer is located under each bolt head and each nut.
(Refer to ‘Plastic Bolt Head Covers’ below.)
Step 3: Tighten all bolts and nuts securely using two 16mm spanners.
Step 4: Push all nut/bolt head covers into place.
PLASTIC BOLT HEAD COVERS
NOTE: Your Australian Barbell Racking has been supplied with special Plastic Bolt-Head Covers.
These are used to cover all bolt heads and nuts. When assembling racking, please follow these
instructions to ensure they are fitted correctly.
i) Ensure that the flange on the Flanged Washer is facing upwards.
ii) After all bolts have been fully tightened, push the Plastic Bolt-Head Cover down onto the
steel washer and it will snap into place.
SIDE VIEW
TOP/BACK VIEW
Make sure bevel
on 45mm End Washer
faces outwards.
45mm End Washers
CLOSE UP
Use 4.5mm End Washers
in these locations.
45mm End Washer not
required in these areas for
30 Class Bar rack. Use in
outside bolt positions only
.
FULLY ASSEMBLED RACK
Australian Barbell Company
54 Bond St West, Mordialloc, VIC 3195
ABN 29 004 420 848
P 03 9580 5945
F 03 9580 7123
[email protected]
www.australianbarbellco.com
20/30 CLASS BAR RACK
ASSEMBLY INSTRUCTIONS
Step 1: Arrange Racking as shown below. Note, pictures below are of the
20 bar rack. The 30 bar rack has three columns of plate storage.
Step 2: Loosely bolt into position ensuring;
i) 45mm End Washers are used at each position listed below.
ii) A flanged washer is located under each bolt head and each nut.
(Refer to ‘Plastic Bolt Head Covers’ below.)
Step 3: Tighten all bolts and nuts securely using two 16mm spanners.
Step 4: Push all nut/bolt head covers into place.
PLASTIC BOLT HEAD COVERS
NOTE: Your Australian Barbell Racking has been supplied with special Plastic Bolt-Head Covers.
These are used to cover all bolt heads and nuts. When assembling racking, please follow these
instructions to ensure they are fitted correctly.
i) Ensure that the flange on the Flanged Washer is facing upwards.
ii) After all bolts have been fully tightened, push the Plastic Bolt-Head Cover down onto the
steel washer and it will snap into place.
SIDE VIEW
TOP/BACK VIEW
Make sure bevel
on 45mm End Washer
faces outwards.
45mm End Washers
CLOSE UP
Use 4.5mm End Washers
in these locations.
45mm End Washer not
required in these areas for
30 Class Bar rack. Use in
outside bolt positions only
.
FULLY ASSEMBLED RACK
  • Page 1 1
  • Page 2 2

Australian Barbell Company 20 Class Bar Rack Assembly Instructions

Brand
Australian Barbell Company
Model
20 Class Bar Rack
Type
Assembly Instructions

Australian Barbell Company 20 Class Bar Rack is a sturdy and versatile storage solution for barbells and weight plates. It can accommodate up to 30 barbells and has three columns of plate storage, making it ideal for gyms, fitness centers, and home gyms. The rack is easy to assemble and comes with special plastic bolt-head covers to protect the bolts and nuts from damage.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents