Gigabyte G262-ZO0 User manual

G262-ZO0

HPC Server - 2U DP AMD OAM 4 GPU Server

User Manual

Rev. 1.0

Copyright

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE without

prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without GIGABYTE's prior written permission.

Documentation Classications

In order to assist in the use of this product, GIGABYTE provides the following types of documentation:

 User Manual: detailed information & steps about the installation, conguration and use of this

product (e.g. motherboard, server barebones), covering hardware and BIOS.



User Guide: detailed information about the installation & use of an add-on hardware or

software component (e.g. BMC rmware, rail-kit) compatible with this product.

 Quick Installation Guide: a short guide with visual diagrams that you can reference easily for

installation purposes of this product (e.g. motherboard, server barebones).

Please see the support section of the online product page to check the current availability of these

documents.

For More Information

For related product specications, the latest rmware and software, and other information please visit our website at

http://www.gigabyte.com

For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our reseller

portal: http://reseller.b2b.gigabyte.com

For further technical assistance, please contact your GIGABYTE representative or visit

https://esupport.gigabyte.com/ to create a new support ticket

For any general sales or marketing enquiries, you may also message GIGABYTE server directly by email:

server[email protected]

Conventions

The following conventions are used in this user's guide:

NOTE!

Gives bits and pieces of additional

information related to the current topic.

CAUTION!

Gives precautionary measures to

avoid possible hardware or software problems.

WARNING!

Alerts you to any damage that might

result from doing or not doing specic actions.

Server Warnings and Cautions

Before installing a server, be sure that you understand the following warnings and cautions.

WARNING!

To reduce the risk of electric shock or damage to the equipment:

• Do not disable the power cord grounding plug. The grounding plug is an important safety

feature.

• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all

times.

• Unplug all the power cords from the power supplies to disconnect power to the equipment.

• Shock Hazard! Disconnect all power supply cords before servicing.

• Do not route the power cord where it can be walked on or pinched by items placed against it.

Pay particular attention to the plug, electrical outlet, and the point where the cord extends from

the server.

WARNING!

To reduce the risk of personal injury from hot surfaces, allow the drives

and the internal system components to cool before touching them.

WARNING!

This server is equipped with high speed fans. Keep away from hazardous

moving fan blades during servicing.

WARNING!

This equipment is not suitable for use in locations where children are

likely to be present.

WARNING!

This equipment is intended to be used in Restrict Access Location. The

access can only be gained by Skilled person.

Only authorized by well trained professional person can access the

restrict access location.

CAUTION!

• Do not operate the server for long periods with the access panel open or removed.

Operating the server in this manner results in improper airow and improper cooling that can

lead to thermal damage.

• Danger of explosion if battery is incorrectly replaced.

• Replace only with the same or equivalent type recommended by the manufacturer.

• Dispose of used batteries according to the manufacturer’s instructions.

Electrostatic Discharge (ESD)

CAUTION!

ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOMMEND THAT YOU

PERFORM ALL PROCEDURES AT AN ESD WORKSTATION. IF ONE IS NOT AVAILABLE,

PROVIDE SOME ESD PROTECTION BY WEARING AN ANTI-STATIC WRIST STRAP AT-

TACHED TO CHASSIS GROUND -- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER

WHEN HANDLING PARTS.

Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by

their edges without any component and pin touching. After removing a board from its protective

wrapper or from the system, place the board component side up on a grounded, static free sur-

face. Use a conductive foam pad if available but not the board wrapper. Do not slide board over

any surface.

System power on/o: To remove power from system, you must remove the system from

rack. Make sure the system is removed from the rack before opening the chassis, adding, or

removing any non hot-plug components.

Hazardous conditions, devices and cables: Hazardous electrical conditions may be

present on power, telephone, and communication cables. Turn off the system and disconnect the

cables attached to the system before servicing it. Otherwise, personal injury or equipment dam-

age can result.

Electrostatic discharge (ESD) and ESD protection: ESD can damage drives,

boards, and other parts. We recommend that you perform all procedures in this chapter only at

an ESD workstation. If one is not available, provide some ESD protection by wearing an antistatic

wrist strap attached to chassis ground (any unpainted metal surface on the server) when handling

parts.

ESD and handling boards: Always handle boards carefully. They can be extremely

sensitive to electrostatic discharge (ESD). Hold boards only by their edges. After removing a

board from its protective wrapper or from the system, place the board component side up on a

grounded, static free surface. Use a conductive foam pad if available but not the board wrapper.

Do not slide board over any surface.

Installing or removing jumpers: A jumper is a small plastic encased conductor that slips

over two jumper pins. Some jumpers have a small tab on top that can be gripped with ngertips

or with a pair of ne needle nosed pliers. If the jumpers do not have such a tab, take care when

using needle nosed pliers to remove or install a jumper; grip the narrow sides of the jumper with

the pliers, never the wide sides. Gripping the wide sides can dam-age the contacts inside the

jumper, causing intermittent problems with the function con-trolled by that jumper. Take care to

grip with, but not squeeze, the pliers or other tool used to remove a jumper, or the pins on the

board may bend or break.

CAUTION!

Risk of explosion if battery is replaced incorrectly or with an incorrect type. Replace the battery

only with the same or equivalent type recommended by the manufacturer. Dispose of used bat-

teries according to the manufacturer’s instructions.

- 7 -

Table of Contents

Chapter 1 Hardware Installation ...................................................................................11

1-1 Installation Precautions .................................................................................. 11

1-2 Product Specications .................................................................................... 12

1-3 System Block Diagram ................................................................................... 16

Chapter 2 System Appearance ..................................................................................... 17

2-1 Front View ...................................................................................................... 17

2-2 Rear View ....................................................................................................... 18

2-3 Front Panel LED and Buttons ........................................................................ 19

2-4 Front System LAN LEDs ................................................................................ 20

2-5 Power Supply Unit (PSU) LED ....................................................................... 21

2-6 Hard Disk Drive LEDs .................................................................................... 22

Chapter 3 System Hardware Installation ......................................................................23

3-1 Removing and Installing the Top Rear Cover ................................................. 24

3-2 System Components ...................................................................................... 25

3-3 Removing and Installing the Fan Duct ........................................................... 26

3-4 Removing the GPU Module ........................................................................... 27

3-5 Removing the CPU Heat Sink ........................................................................ 28

3-6 Installing the CPU .......................................................................................... 29

3-7 Installing Memory ........................................................................................... 30

3-7-1 Eight Channel Memory Conguration .....................................................................30

3-7-2 Installing the Memory ............................................................................................31

3-7-3 Processor and Memory Module Matrix Table .........................................................31

3-7-4 Memory Population Table .......................................................................................32

3-8 Installing the PCI Expansion Card ................................................................. 33

3-9 Replacing the System FAN Module ............................................................... 43

3-10 Installing the Hard Disk Drive ......................................................................... 44

3-11 Removing and Installing the Power Supply .................................................... 45

3-12 Cable Routing ................................................................................................ 46

Chapter 4 Motherboard Components ...........................................................................53

4-1 Motherboard Components ............................................................................. 53

4-2 Jumper Setting .............................................................................................. 54

4-3 NVMe HDD Conguration ............................................................................. 54

- 8 -

Chapter 5 BIOS Setup ..................................................................................................55

5-1 The Main Menu .............................................................................................. 57

5-2 Advanced Menu ............................................................................................. 59

5-2-1 Trusted Computing .................................................................................................61

5-2-2 PSP Firmware Versions ..........................................................................................62

5-2-3 Legacy Video Select ...............................................................................................63

5-2-4 AST2500 Super IO Conguration ...........................................................................64

5-2-5 S5 RTC Wake Settings ...........................................................................................67

5-2-6 Serial Port Console Redirection .............................................................................68

5-2-7 CPU Conguration ..................................................................................................72

5-2-8 PCI Subsystem Settings .........................................................................................73

5-2-9 USB Conguration ..................................................................................................75

5-2-10 Network Stack Conguration ..................................................................................77

5-2-11 NVMe Conguration ...............................................................................................78

5-2-12 SATA Conguration.................................................................................................79

5-2-13 Graphic Output Conguration .................................................................................80

5-2-14 AMD Mem Conguration Status .............................................................................81

5-2-15 Tls Auth Conguration ............................................................................................82

5-2-16 ISCSI Conguration ................................................................................................83

5-2-17 Intel(R) I350 Gigabit Network Connection ..............................................................84

5-2-18 VLAN Conguration ................................................................................................86

5-2-19 MAC IPv4 Network Conguration ...........................................................................87

5-2-20 MAC IPv6 Network Conguration ...........................................................................88

5-3 AMD CBS Menu ............................................................................................. 89

5-3-1 CPU Common Options ...........................................................................................90

5-3-2 DF Common Options ..............................................................................................96

5-3-3 UMC Common Options ........................................................................................101

5-3-4 NBIO Common Options ........................................................................................ 116

5-3-5 FCH Common Options .........................................................................................122

5-3-6 SOC Miscellaneous Control .................................................................................126

5-3-7 Workload Tuning ...................................................................................................127

5-4 AMD PBS Menu ........................................................................................... 128

5-4-1 RAS ......................................................................................................................129

5-5 Chipset Setup Menu ..................................................................................... 131

5-5-1 North Bridge .........................................................................................................132

5-5-2 Fabric Resource ...................................................................................................133

5-6 Server Management Menu ........................................................................... 134

5-6-1 System Event Log ................................................................................................136

5-6-2 View FRU Information ..........................................................................................137

5-6-3 BMC Network Conguration .................................................................................138

5-6-4 IPv6 BMC Network Conguration .........................................................................139

- 9 -

5-7 Security Menu .............................................................................................. 140

5-7-1 Secure Boot .........................................................................................................141

5-8 Boot Menu .................................................................................................... 143

5-8-1 UEFI NETWORK Drive BBS Priorities ................................................................145

5-8-2 UEFI Application Boot Priorities ................................................................. 146

5-9 Save & Exit Menu ......................................................................................... 147

5-10 BIOS POST Beep code (AMI standard) ....................................................... 148

5-10-1 PEI Beep Codes ...................................................................................................148

5-10-2 DXE Beep Codes .................................................................................................148

- 10 -

This page intentionally left blank

- 11 - Hardware Installation

1-1 Installation Precautions

The motherboard/system contain numerous delicate electronic circuits and components which

can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully

read the user manual and follow these procedures:

• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

• Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

• When connecting hardware components to the internal connectors on the motherboard,

make sure they are connected tightly and securely.

• When handling the motherboard, avoid touching any metal leads or connectors.

• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

components such as a motherboard, CPU or memory. If you do not have an ESD wrist

strap, keep your hands dry and rst touch a metal object to eliminate static electricity.

•

Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

• Before unplugging the power supply cable from the motherboard, make sure the power

supply has been turned off.

• Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

• Before using the product, please verify that all cables and power connectors of your

hardware components are connected.

• To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

• Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

• Do not place the computer system on an uneven surface

.

• Do not place the computer system in a high-temperature environment.

• Turning on the computer power during the installation process can lead to damage to

system components as well as physical harm to the user.

• If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certied computer technician.

Chapter 1 Hardware Installation

Hardware Installation - 12 -

1-2 Product Specications

CPU AMD EPYC™ 7003 processors with AMD 3D V-Cache™ Technology

AMD EPYC™ 7003 series processor family

Dual processors, 7nm

Up to 64-core, 128 threads per processor

cTDP up to 280W

NOTE: If only 1 CPU is installed, some PCIe or memory functions might be

unavailable.

Compatible with AMD EPYC™ 7002 series processor family

Socket Socket SP3

Chipset System on Chip

Memory 16 x DIMM slots

DDR4 memory supported only

8-Channel memory per processor architecture

RDIMM modules up to 128GB supported

LRDIMM modules up to 128GB supported

3DS RDIMM/LRDIMM modules up to 256GB supported

Memory speed: Up to 3200/ 2933 MHz

LAN Front side:

2 x 1GbE LAN ports (1 x Intel® I350-AM2)

1 x 10/100/1000 management LAN

Video Integrated in Aspeed® AST2500

2D Video Graphic Adapter with PCIe bus interface

1920x1200@60Hz 32bpp, DDR4 SDRAM

Storage 4 x 2.5" Gen4 U.2 NVMe/ SATA/ SAS hot-swappable HDD/SSD bays

SAS card is required for SAS devices support

SAS Depends on optional SAS Card

RAID Depends on optional SAS Card

NOTE:

We reserve the right to make any changes to the product specications and product-related informa-

tion without prior notice.

- 13 - Hardware Installation

Expansion Slot Pre-installed with 4 x AMD MI250 OAM GPU modules

128GB HBM2e Memory per OAM module

Up to 6x GPU-GPU Innity Links at 25Gbps

Total 6 x Low prole Gen4 x16 expansion slots

Front Side: 2 x Low prole Gen4 x16 expansion slots

Rear Side: 4 x Low prole Gen4 x16 expansion slots

1 x OCP 3.0 mezzanine slot with PCIe Gen4 x16 bandwidth from CPU_0

Supported NCSI function by onboard NCSI_SW

1 x M.2 slot: (Onboard)

M-key

PCIe Gen4 x4

Supports 2280/22110 cards

2 x M.2 slots: (From CMTP072)

M-key

PCIe Gen4 x4

Supports 2242/2260/2280/22110 cards

Internal I/O 1 x TPM header

1 x Front panel header

Front I/O 2 x USB 3.0

1 x mini-DP

2 x RJ45

1 x MLAN

1 x Power button with LED

1 x ID button with LED

1 x Reset button

1 x System status LED

1 x HDD access LED

Backplane I/O 4 x 2.5" NVMe/ SATA hybrid ports

Speed and bandwidth: PCIe Gen4 or SATA 6Gb/s

TPM 1 x TPM header with SPI interface

Optional TPM2.0 kit: CTM010

Hardware Installation - 14 -

Power Supply 2 x 3000W redundant power supply

80 PLUS Platinum

AC Input:

115-127V~/ 14.2A, 50-60Hz

200-240V~/ 15.8A, 50-60Hz

DC Intput:

240Vdc/ 14A

DC Output:

Max 1200W/ 100-127V~

+54V/ 95.6A

+12Vsb/ 3.5A

- Max 3000W/ 200-240V~

+54V/ 178.1A

+12Vsb/ 3.5A

NOTE: The system power supply requires C19 type power cord

System

Management Aspeed® AST2500 management controller

GIGABYTE Management Console (AMI MegaRAC SP-X) web interface

Dashboard

HTML5 KVM

Sensor Monitor (Voltage, RPM, Temperature, CPU Status …etc.)

Sensor Reading History Data

FRU Information

SEL Log in Linear Storage / Circular Storage Policy

Hardware Inventory

Fan Prole

System Firewall

Power Consumption

Power Control

LDAP / AD / RADIUS Support

Backup & Restore Conguration

Remote BIOS/BMC/CPLD Update

Event Log Filter

User Management

Media Redirection Settings

PAM Order Settings

SSL Settings

SMTP Settings

- 15 - Hardware Installation

Operating

Properties

Operating temperature: 10°C to 35°C

Operating humidity: 8%-80% (non-condensing)

Non-operating temperature: -40°C to 60°C

Non-operating humidity: 20%-95% (non-condensing)

System

Dimension

2U

448 (W) x 86.8 (H) x 800 (D) (mm)

Hardware Installation - 16 -

1-3 System Block Diagram

- 17 - System Appearance

Chapter 2 System Appearance

2-1 Front View

1 8 7 6 5 4

2 3

HDD0

HDD1

HDD2

HDD3

No. Description

1. Front Panel LEDs and Buttons

2. PCIe Card Slot

3. PCIe Card Slot

4. Mini DP Port

5. USB 3.0 Port x 2

6. GbE LAN Port x 2

7. 10/100/1000 Server Management LAN Port

8. Mezzanine Card Slot (Option/OCP3)

NOTE! The Green HDD Latch Supports NVMe

• Please Go to Chapter 2-3 Front Panel LED and Buttons for detail description of function

LEDs.

System Appearance - 18 -

2-2 Rear View

PSU1

PSU2

PCIe 2

PCIe 1

PCIe 3

PCIe 4

1

No. Description

1. Full-Height Half-Length PCIe Card Slot x 4

- 19 - System Appearance

2-3 Front Panel LED and Buttons

RST

1

2

3

4

5

No. Name Color Status Description

1. Reset Button -- -- Press the button to reset the system.

2. Power button

with LED

Green On Indicates the system is powered on.

Green Blink System is in ACPI S1 state (sleep mode).

N/A Off • System is not powered on or in ACPI S5 state (power off)

• System is in ACPI S4 state (hibernate mode)

3. HDD Status

LED

Green On Indicates locating the HDD.

Blink Indicates accessing the HDD.

Amber On Indicates HDD error.

Green/

Amber Blink Indicates HDD rebuilding.

N/A Off Indicates no HDD access or no HDD error.

4. ID Button Press the button to activate system identication

5. System

Status LED

Green On Indicates system is operating normally.

Amber

On

Indicates a critical condition, may include:

-System fan failure

-System temperature

Blink

Indicates non-critical condition, may include:

-Redundant power module failure

-Temperature and voltage issue

-Chassis intrusion

N/A Off

Indicates system is not ready, may include:

-POST error

-NMI error

-Processor or terminator is missing

System Appearance - 20 -

2-4 Front System LAN LEDs

No. Name Color Status Description

1. 1GbE

Speed LED

Yellow On 1 Gbps data rate

Green On 100 Mbps data rate

N/A Off 10 Mbps data rate

2.

1GbE

Link/

Activity

LED

Green

On Link between system and

network or no access

Blink Data transmission or receiving is occurring

N/A Off No data transmission or

receiving is occurring

1 2 1 2 1 2

Page is loading ...

Gigabyte G262-ZO0 User manual

Related papers

Other documents