To avoid personal injury and/or property damage, please read and follow
ALL instructions before assembling and operating.
KEEP THIS MANUAL FOR REFERENCE
#06430
5000 LB. WINCH
12V DC
WARNING
Contact Information
Marine City, Michigan 48039
Thamesville, Ontario N0P 2K0
Toll Free: 1-888-546-4668
2
Safety READ THOROUGHLY BEFORE OPERATION YOUR WINCH.
FAILURE TO FOLLOW INSTRUCTIONS COULD RESULT IN
SERIOUS HARM OR DEATH
IF YOU HAVE QUESTIONS ABOUT YOUR WINCH, OR
ABOUT WINCH SAFE USE CONTACT
1. DO NOT exceed the rated capacity
2. DO NOT use for lifting or moving people or animals
3. Maintain a safe distance to the side of the cable when under tension
4. NEVER step OVER or NEAR a cable under load
5. The wire may break before the motor stalls. When loads are near or at rated capacity, use a
pulley block/snatch block to reduce the load on the wire rope.
6. DO NOT operate vehicle to pull a load on the winch cable (towing). This could result in
cable breakage.
7. Use specied anchor points on vehicle per manufacturer.
8. Winch is not intended to secure or hold a vehicle for extended period of time.
9. Do not use winch to secure load for transportation
10. After use disconnect remote control and battery leads
11. Do not accelerate your vehicle while winching. Loss of traction can cause a shock load on
the cable.
12. Keep sparks, and ames away from batteries at all time. Do not lean over battering during
operation. Wear protective eyeware.
13. Do not hoist loads or use for overhead lifting.
14. If motor stalls, do not maintain power to the winch.
ELECTRIC WINCHES ARE DESIGNED FOR INTERMITTENT USE.
15. Operate winch for short bursts. If the motor becomes uncomfortably hot to the touch, stop
winching immediately. DO NOT EXCEED PULL FOR MORE THAN 1 MIN. AT OR
NEAR RATED LOAD.
16. Never release the free-spool clutch when there is a load on the winch.
17. Use hook strap when handling the hook for spooling or unspooling the wire rope.
18. Use gloves when handling the cable. Never let the cable slide through your hands.
19. DO NOT wrap the cable around any object and hook back onto itself.
20. Use blocks under wheels of vehicle when on incline.
3
Components
Specifications
WARNING: DO NOT OPERATE IF ANY COMPONENTS ARE
MISSING OR DAMAGED. FAILURE TO COMPLY COULD RE-
SULT IN MULFUNCTION OR PERSONAL INJURY.
1. Winch / Treuil
2. Solenoid / Relais
3. Wiring / Câble
7. Handle bar mount / Interrupteur
8. Hook / Crochet
9. Fairlead / Guide-câble
4. Rocket switch / Interrupteur à bascule
5. Mounting plate / Plaque de montage
6. Assist strap / Sangle d’appoint
12
3
4
5
7
8
9
6
4
Assembly This class of winch is designed with a standard bolt pattern to
t many mounting kits available.
DO NOT route cables across sharp edges, through
or near moving parts, or parts that become hot.
DO NOT route cables across sharp edges, through
or near moving parts, or parts that become hot.
1. Insert bolts through mounting plate hole and
attach the roller fairlead to the mounting plate
with at washer, lock washer, and nut.
2. Attach the winch to the mounting plate and
at surface. Secure the winch to the mount-
ing plate with nut, at washer, and lock
washer.
3. Rotate the clutch knob to the ‘OUT’ position
to disengage clutch. Spool out a short lead
of wire rope. Feed wire rope through roller
fairlead.
4. Attach the clevis hook to the cable. Attach
assist strap to clevis hook.
1. The remote is typically installed on the left handlebar.
2. Use a piece of eletrical atpe around the handlebar to
prevent the remote from rotating. Do not tighten over
any hoses or cables.
3. Route the wires back to the battery
and winch.
4. Ensure there is full range of motion with the handle-
bars, then secure the remote controllers cables.
Motor leads may be rotated to avoid interferance with
other components
1. Decide which handlebar the rocker switch will be
mounted on. (The rocker switch is usually installed
on the left handlebar).
2. Use a piece of electrical tape (not provided) around
the handlebar to help prevent rotation of the mount.
3. Tighten the rocker switch in place. DO NOT over
tighten or tighten/clamp over any hoses or cables.
4. Once the rocker switch is mounted, the wires can
be routed back to where thte solenoid/ contactor is
located.
5. Make sure the handlebars have full range of motion
and then secure the rocker switch’s cable with the
supplied cable ties.
1. Connect the yellow and blue cables to the motor
terminals on the winch . (Yellow to the positive (+)
terminal of the motor . Blue to the negative(-) termi-
nal of the motor) . Tighten the terminal nuts on the
motor . DO NOT over tighten . Route the other ends
to the solenoid/ contactor location .
2. Connect the yellow and blue cables to the solenoid/
contactor (yellow to yellow and blue to blue). DO
NOT tighten nuts.
3. Connect the red and black cables to the solenoid/
contactor (red to red and black to black). DO NOT
tighten nuts. Route the other ends to the vehicle’s
battery.
4. Connect the red lead to the positive (+) terminal of
the vehicle’s 12 volt battery .
5. Connect the rocker switch to the solenoid/ contactor
(black to black and green to green) .
6. Splice the end of the red wire on the rocker switch,
to an ignition (keyed) controlled power source using
the supplied wire tap.
Assembling the Winch
Mounting the Remote
Installing the Rocker Switch
Wiring the Winch
Ensure motor, drum, and gear housing are
properly aligned on mounting plate for even
distribution of the rated load.
5
Motor leads may be rotated to avoid interferance with
other components
Wiring the Winch
Wiring the Switch
Wiring Diagrams
Positive
Negative
Blue Red
Black
Yellow
(+)
(-)
Positive
To Switch and Remote
Wiring. See Diagram
Negative
(+)
(-)
7. Once all wiring is connected to the solenoid/
contactor it can then be mounted using the
supplied M6 hardware.
8. Tighten the solenoid/contactor terminal nuts .
DO NOT over tighten.
9. Connect the black lead to the negative (–) ter-
minal of the vehicle’s 12 volt battery.
10. Place all terminal boots over terminals and
secure all cables with cable ties or electrical
tape (not provided).
11. Check for proper drum rotation. Pull and turn
the clutch knob to the “OUT” position (free
spooling). Pull out some cable from the drum,
and then turn the clutch knob to the “IN”
position to engage the gears. Press the cable
out button on the rocker switch. If the drum is
turning and releasing more cable, then your
connections are accurate. If the drum is turn-
ing and collecting more cable then reverse the
leads on the motor. Repeat and check rotation.
wiring continued
Green
Red
Ignition Wire
Black
66
Operation
General Tips for Safe Operation
Overloads can damage the winch, motor and/or wire rope. For loads over 50% the rated load
we recommend the use of a pulley block/snatch block to double the wire rope line. This will aid
in two ways:
(a) reduce the number or rope layers on the drum
(b) reduce the load on the wire rope by as much as 50%.
When doubling the line back to the vehicle, attach to the tow hook, frame or other load bearing
part. The vehicle engine should be kept running during operation of the winch to minimize bat-
tery drain and maximize power and speed of the winch. If the winch is used for a considerable
time with the engine off the battery may be drained and too weak to restart the engine.
We recommend that you set up a few test runs to familiarize yourself with rigging techniques,
the sounds your winch makes under various loads, the way the cable spools on the drum, etc.
Inspect the wire rope and equipment before each use. A frayed or damaged rope MUST be
replaced immediately. Inspect the winch installation and bolts to ensure that all bolts are tight
before each operation. Store the remote control in a place that it will not be damaged.
Any winch that appears to be damaged in any way, or operates abnormally MUST BE RE-
MOVED FROM SERVICE UNTIL REPAIRED.
Self Recovery
Locate a suitable anchor such as a strong tree trunk or boulder.
Always use a sling as an anchor point. (g. 1)
The roller fairlead helps guide the wire rope to reduce binding on short side pulls. DO NOT
PULL FROM acute angle. Wire rope that collects at one side of the drum will cause damage.
(g. 2)
A short pull from an angle can be used to straighten a vehicle. Long pulls the rope should be
at 90° to the winch.
Place a blanket/jacket over the wire rope ~6’ from the hook to dampen any snapback from a
broken cable. For additional protection open the hood of the vehicle. (g. 3)
g.2 Safe pulling angle g.3 Dampen possible snapback
from broken cable
g.1 Sling as anchor point
15˚
15˚
77
Warranty Qualifications
Effective from the day you purchase the product. Please keep your dated purchase invoice as proof.
Repair/Replacement Warranty
Erickson Manufacturing Ltd. warrants to the original purchaser that the mechanical components
will be free of defect in material and workmanship for 90 days from the original date of purchase.
Transportation charges on product submitted for repair or replacement under warranty are the
sole responsibility of the purchaser. This warranty only applies to the original purchaser and is
not transferable.
Do Not Return The Unit to the Place of Purchase
Contact Erickson Manufacturing Ltd’s Technical Service and service people will troubleshoot any
issue via phone or email. Repairs or replacements without prior authorization, or at an unauthorized
repair facility, will not be covered by this warranty.
Warranty Exclusions
This warranty does not cover the following repairs and equipment:
Normal Wear
This warranty does not cover the repair when use has exhausted the life of a part or the equipment
as a whole.
Installation, Use and Maintenance
This warranty will not apply to parts and/or labor if this product is deemed to have been misused,
neglected, involved in an accident, abused, loaded beyond specifications, modified, or installed
improperly. Normal maintenance is not covered by this warranty.
Other Exclusions
This warranty excludes:
• Cosmetic defect such as paint, decal etc.
• Wear items
• Accessory parts
• Failures due to acts of God and other force majeure events beyond the manufacturer’s control.
• Problems cause by parts that are not Erickson Manufacturing Ltd. parts.
Limits of implied Warranty and Consequential Damage
Erickson Manufacturing Ltd. disclaims any obligation to cover any loss time, use of this product, freight,
or any incidental or consequential claim by anyone from using this product. THIS WARRANTY IS
IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. A unit provided as exchange will
be subject to the warranty of the original unit. The length of the warranty governing the
exchanged unit will remain calculated by reference to the purchase date of the original unit. This
warranty gives you certain legal rights which may change from state to state. Your state and/or
province may also have other right you may be entitled to that are not listed within this warranty.
Contact Information
Marine City, Michigan 48039
Thamesville, Ontario N0P 2K0
Toll Free: 1-888-546-4668
Warranty
8
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Princess auto 9060922 User manual
-
Warn 103255 Installation guide
-
Champion Power Equipment 100218 User manual
-
Champion Power Equipment 201162 User manual
-
Champion Power Equipment 13050 User manual
-
Champion Power Equipment 13502 User manual
-
Champion Power Equipment 14001 User manual
-
Champion Power Equipment 14061 User manual
-
Champion Power Equipment 14560 Owner's Manual & Operating Instructions
-
Champion Power Equipment 12551 User manual
